Ethynylene‐containing donor–acceptor alternating conjugated polymers: Synthesis and photovoltaic properties

Four ethynylene‐containing donor‐acceptor alternating conjugated polymers P1 – P4 with 2,5‐bis(dodecyloxy) substituted phenylene or carbazole as the donor unit and benzothiadiazole (BTZ) as the acceptor unit were synthesized and used as donor polymers in bulk heterojunction polymer solar cells. The optical, electrochemical, and photovoltaic properties of these four polymers with the ethylene unit located at different positions of the polymer chains were systematically investigated. Our results demonstrated that absorption spectra and the HOMO and LUMO energy levels of polymers could be tuned by varying the position of the ethynylene unit in the polymer chains. Photovoltaic devices based on polymer/PC₇₁BM blend films spin coated from chloroform and dichlorobenzene solutions were investigated. For all four polymers, open circuit voltages (V_oc) higher than 0.8 V were obtained. P4 , with ethynylene unit between BTZ and thiophene, shows the best performance among these four polymers, with a V_oc of 0.94 V, a J_sc of 4.2 mA/cm², an FF of 0.40, and a PCE of 1.6%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Imide‐functionalized naphthodithiophene based donor‐acceptor conjugated polymers for solar cells

Donor‐acceptor conjugated polymers containing a new imide‐functionalized naphthodithiophene (INDT) as the acceptor unit and a 2,2'‐bithiophene with varied substituents as the donor unit have been synthesized. The bandgaps of these polymers depend strongly on the dihedral angle of the 2,2'‐bithiophene unit. The 3,3'‐dialkoxy substitution (polymers PDOR / PBOR ) leads to near planar bithiophene conformation due to the well‐known S–O short contact, while the 3,3'‐dialkyl substitution (polymer PDR ) results in significant twisting due to the steric effect. Consequently PDOR / PBOR shows the lowest bandgap of 1.82/1.85 eV while PDR has a bandgap of 2.38 eV. Bulk‐heterojunction solar cells of the polymer/fullerene blends have been fabricated. Preliminary results show that PBOR gives the best device performance with power conversion efficiencies as high as 2.45% in air without any thermal annealing treatment, indicating the promising potential of INDT‐containing conjugated polymers for efficient solar cells. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3818–3828     

Dithienobenzimidazole‐containing conjugated donor–acceptor polymers: Synthesis and characterization

The synthesis of two new conjugated polymers based on the relatively under‐exploited monomer, 5,8‐dibromo‐2‐[5‐(2‐hexyldecyl)‐2‐thienyl]‐1H‐dithieno[3,2‐e:2′,3′‐g]benzimidazole (dithienobenzimidazole, DTBI ), and either 4,7‐bis[4‐hexyl‐5‐(trimethylstannyl)‐2‐thienyl]‐2,1,3‐benzothiadiazole ( BTD ) or 2,6‐bis(trimethylstannyl)‐4,8‐bis(5‐(2‐ethylhexyl) thiophen‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene ( BDT ) is described. The polymers were synthesized via Stille polycondensation and characterized by traditional methods (¹H NMR, gel‐permeation chromatography, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, thermal gravimetric analysis, differential scanning calorimetry, ultraviolet–visible spectroscopy, photoluminescence, and cyclic voltammetry). Prior to their synthesis, trimer structures were modeled by DFT calculations facilitating a further understanding of the systems' electronic and geometric structure. Polymers were titrated with acid and base to take advantage of their amphiprotic imidazole moiety and their optical response monitored with ultraviolet–visible spectroscopy. Finally, pristine polymer thin‐films were treated with acid and base to evaluate (de)protonation's effect on system electronics, but thin‐film degradation was encountered. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 60–69     

Design and synthesis of pyromellitic diimide‐based donor–acceptor conjugated polymers for photovoltaic application

Three of conjugated polymers based on pyromellitic diimide (PMDI) as the acceptor unit and thienothiophene (TT) as the donor unit were successfully synthesized by Stille coupling. The effect of the side chain length and thiophene π‐bridge on the polymers' optical and electrochemical properties was investigated. Electrochemical characterization indicated that these polymers have deep highest occupied molecular orbital energy levels between ?5.7 and ?5.8 eV. Polymer solar cells were fabricated by using these PMDI‐based polymers as the donor and [6,6]‐phenyl‐C61‐butyric acid methyl ester as the acceptor. The polymer P1 whose PMDI unit was functionalized with 2‐ethylhexyl side chain shows the higher short‐circuit current (J_sc) and fill factor (FF) compared with that of P2 with a 2‐octyldodecyl side chain on the PMDI unit. The results also illustrate that the insertion of a thiophene π‐bridge between PMDI and TT (the polymer P3) leads to the broader absorption and better photovoltaic performance. The best performance was obtained from the cell based on the polymer P3 with a power conversion efficiency of 0.43% under the illumination of AM 1.5 G, 100 mW/cm². Copyright © 2014 John Wiley & Sons, Ltd.     

New benzodithiophene‐ and benzooxadiazole/benzothiadiazole‐based donor–acceptor π‐conjugated polymers for organic photovoltaics

A new set of push‐pull type 2D‐conjugated polymers (P1–P4) were designed and synthesized where A1, A2 (oxygen analogues) and A3, A4 (sulfur analogues) are electron deficient units used as co‐monomers. On introduction of new repeating units into the polymer backbone, significant changes were observed in optoelectronic properties. Furthermore, the heteroatom exchange in new repeating units has also brought notable changes in photophysical properties, in particular P1 and P2 (oxygen analogues) showed bathochromic shift in UV‐vis absorption spectra and deeper HOMO energy levels than P3, P4 (sulfur analogues). Interestingly P1, P3 absorption spectra shows a vibronic shoulder (659, 652 nm) peak in lower energy region, and this might originated from non‐covalent interactions between the electron rich and electron deficient units. In addition, the systematic investigation of these polymers with additive and solvent treatment, yielded in enhanced power conversion efficiency of 4.29% for P3‐based devices in bulk heterojunction organic solar cells. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2668–2679     

Synthesis and morphology of all‐conjugated donor–acceptor block copolymers based on poly(3‐hexylthiophene) and poly(naphthalene diimide)

A series of all‐conjugated diblock and triblock copolymers comprised of poly(naphthalene diimide) (PNDI)‐based n‐type and the poly(3‐hexylthiophene) (P3HT) segments could be synthesized via the Kumada catalyst‐transfer polycondensation process. The crystalline structures and chain orientation of the block copolymer thin films were systematically studied by grazing incident wide‐angle X‐ray scattering (GIWAXS). The GIWAXS results indicated that both the P3HT and PNDI segments in the block copolymers form exclusive crystalline domains in which the P3HT domain aligns with an edge‐on rich orientation, and the PNDI domain aligns with a face‐on rich orientation. In contrast, the blend films of the P3HT and PNDI homopolymers also show two distinguished crystalline domains in which the P3HT domain aligns with an edge‐on rich orientation, and the PNDI domains align in different ways depending on the chemical structure of n‐type polymers, that is, PNDI1Th is isotropically dispersed, while PNDI2Th aligns with a face‐on rich orientation. In addition, the effect of thermal annealing on the crystalline behavior of the block copolymers is reported. The GIWAXS results indicated that thermal annealing increases the crystallinity of both segments without affecting their chain orientation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1139–1148     

Effects of substituted side‐chain position on donor–acceptor conjugated copolymers

The optical properties and electrical properties of a series of low‐band‐gap conjugated copolymers, in which alkyl side chains were substituted at various positions, were investigated using donor–acceptor conjugated copolymers consisting of a cyclopentadithiophene derivative and dithienyl‐benzothiadiazole. With substituted side chains, the intrinsic properties of the copolymers were significantly altered by perturbations of the intramolecular charge transfer. The absorption of poly[2, 6‐(4,4‐bis(2‐octyl)‐4H‐cyclopenta‐[2,1‐b:3,4‐b′]dithiophene)‐alt‐4, 7‐bis(4‐octyl‐thiophene‐2‐yl)benzo‐2,1,3‐thiadiazole] [ PCPDT‐ttOTBTOT ( P2 )], which assumed a tail–tail configuration, tended to blue shift relative to the absorption of poly[2,6‐(4,4‐bis(2‐octyl)‐4H‐cyclopenta‐[2,1‐b:3,4‐b′]dithiophene)‐alt‐4,7‐bis (thiophene‐2‐yl)benzo‐2,1,3‐thiadiazole] [ PCPDT‐TBTT ( P1 )]. The absorption of poly[2,6‐(4,4‐bis(2‐octyl)‐4H‐cyclopenta‐[2,1‐b:3, 4‐b′]dithiophene)‐alt‐4,7‐bis(3‐octyl‐thiophene‐2‐yl)benzo‐2,1,3‐thiadiazole] [ PCPDT‐hhOTBTOT ( P3 )], which assumed a head–head configuration, was blue shifted relative to that of P2 . The electrical transport properties of field‐effect transistors were sensitive to the side chain position. The field‐effect mobility in P2 (μ₂ = 1.8 × 10^?3 cm²/V s) was slightly lower than that in P1 (μ₁ = 4.9 × 10^?3 cm²/V s). However, the mobility of P3 was very low (μ₃ = 3.8 × 10^?6 cm²/V s). Photoexcitation spectroscopy showed that the charge generation efficiency (shown in transient absorption spectra) and polaron pair mobility in P1 and P2 were higher than in P3 , yielding P1 and P2 device performances that were better than the performance of devices based on P3 . © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Diketopyrrolopyrrole‐based liquid crystalline conjugated donor–acceptor copolymers with reduced band gap for polymer solar cells

A new liquid crystalline (LC) acceptor monomer 2,5‐bis[4‐(4′‐cyanobiphenyloxy)dodecyl]‐3,6‐dithiophen‐2‐yl‐pyrrolo[3,4‐c]pyrrole‐1,4‐dione (TDPPcbp) was synthesized by incorporating cyanobiphenyl mesogens into diketopyrrolopyrrole (DPP). The monomer was copolymerized with bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′] dithiophene (BDT) and N‐9′‐heptadecanylcarbazole (CB) donors to obtain donor–acceptor alternating copolymers poly[4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐alt‐3,6‐bis(thiophen‐5‐yl)‐2,5‐bis[4‐(4′‐cyanobiphenyloxy)dodecyl]‐2,5‐dihydropyrrolo[3,4‐c]pyrrole‐1,4‐dione] (PBDTDPPcbp) and poly[N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐3,6‐bis(thiophen‐5‐yl)‐2,5‐bis[4‐(4′‐cyano‐biphenyloxy)dodecyl]‐2,5‐dihydropyrrolo[3, 4‐c]pyrrole‐1,4‐dione] (PCBTDPPcpb) with reduced band gap, respectively. The LC properties of the copolymers, the effects of main chain variation on molecular packing, optical properties, and energy levels were analyzed. Incorporating the mesogen cyanobiphenyl units not only help polymer donors to pack well through mesogen self‐organization but also push the fullerene acceptor to form optimized phase separation. The bulk heterojunction photovoltaicdevicesshow enhanced performance of 1.3% for PBDTDPPcbp and 1.2% for PCBTDPPcbp after thermal annealing. The results indicate that mesogen‐controlled self‐organization is an efficient approach to develop well‐defined morphology and to improve the device performance. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Effect of side‐chain positions on morphology and photovoltaic properties of phenazine‐based donor–acceptor copolymers

Two phenazine donor–acceptor‐conjugated copolymers (P1 and P2) with the same polymer backbone but different anchoring positions of alkoxy chain on the phenazine unit were investigated to identify the effect of changing the position of alkoxy chains on their optical, electrochemical, blend film morphology, and photovoltaic properties. Although the optical absorption and frontier orbital energy levels were insensitive to the position of alkoxy chains, the film morphologies and photovoltaic performances changed significantly. P1/PC₇₁BM blend film showed the formation of phase separation with large coarse aggregates, whereas P2/PC₇₁BM blend film was homogeneous and smooth. Accordingly, power conversion efficiency (PCE) of photovoltaic devices increased from 1.50% for P1 to 2.54% for P2. In addition, the PCE of the polymer solar cell based on P2/PC₇₁BM blend film could be further improved to 3.49% by using solvent vapor annealing treatment. These results clearly revealed that tuning the side‐chain position could be an effective way to adjust the morphology of the active layer and the efficiency of the photovoltaic device. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2910–2918     

Photophysics and morphology of a polyfluorene donor–acceptor triblock copolymer for solar cells

We present a study of the optical, structural and device properties of a polyfluorene (PFM)‐based (PFM‐F8BT‐PFM) donor–acceptor triblock copolymer for use in an organic solar cell. Neutron reflectivity is employed to probe the vertical composition profile before and after thermal annealing while the crystallinity was examined using grazing incidence wide‐angle X‐ray. The absorption spectra and photoluminescence emission for the triblock and analogous blend of PFM with F8BT reveal a greater degree of intermixing in the triblock. However, the triblock copolymer exhibits exciplex emission, which necessitates a geminate polar pair; long‐lived exciplex states are detrimental in organic photovoltaic devices. The triplet yield in the triblock and the blend is estimated using photoinduced absorption, with the triblock copolymer generating a triplet population 20 times that of the blend. This is far from ideal as triplets are wasted states in organic photovoltaic devices and they can also act as scavengers of polarons reducing the efficiency even more. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1705–1718     

Time‐resolved spectroscopy study of donor–acceptor‐type copolymers in a monodisperse system: The effect of ratio between the acceptor and the donor

The photoexcitation processes of two donor–acceptor‐type copolymers PCFBT with different ratios between the donor and the acceptor ( PCFBT_0.5 and PCFBT_0.1 ) in the solution system are systematically studied. If the number of the donor is equal to that of the acceptor in one repeat unit (such as PCFBT_0.5 ), intrachain charge transfer (ICT) can occur and participate in the relaxation of the excited state after photoexcitation. When the number of donors is much larger than that of acceptors (such as PCFBT_0.1 ) in one repeat unit, the ICT character can disappear, and the localized exciton decay process is dominant in the relaxation of the copolymer, which also involves an excitation intensity‐independent vibrational thermal relaxation process at the initial time. The results further the understanding of the basic structure‐property relationship. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 992–996     

Synthesis and characterization of donor–acceptor poly(3‐hexylthiophene) copolymers presenting 1,3,4‐oxadiazole units and their application to photovoltaic cells

We have used Grignard metathesis polymerization to prepare poly(3‐hexylthiophene)‐based copolymers containing electron‐withdrawing 4‐tert‐butylphenyl‐1,3,4‐oxadiazole‐phenyl moieties as side chains. We characterized these copolymers using ¹H and ¹³C nuclear magnetic resonance spectroscopy, thermogravimetric analysis, and gel permeation chromatography. The band gap energy of copolymer was determined from the onset of the optical absorption. The quenching effects were observed in the photoluminescence spectra of the copolymers incorporating pendant electron‐deficient 1,3,4‐oxadiazole moieties on the side chains. The photocurrents of devices were enhanced in the presence of an optimal amount of the 1,3,4‐oxadiazole moieties, thereby leading to improved power conversion efficiencies. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3331–3339, 2010     

Soft template synthesis of donor–acceptor conjugated polymer nanoparticles: Structural effects,stability, and photothermal studies

Donor–acceptor conjugated polymer nanoparticles and nanofibers, based on Poly[4,4‐bis(2‐ethylhexyl)‐cyclopenta[2,1‐b;3,4‐b']dithiophene‐2,6‐diyl‐alt?2,1,3‐benzoselenadiazole‐4,7‐diyl] (PCPDTBSe), were synthesized using Pluronic F127 as a template. The nanomaterials were compared to previously reported PCPDTBSe nanoparticles, which were synthesized without the use of a template. Our goal was to improve on the aqueous stability and photothermal heating efficiency of the previously synthesized PCPDTBSe nanoparticles by decreasing their size and coating them with a biocompatible surfactant. The pluronic wrapped PCPDTBSe (PW‐PCPDTBSe) nanoparticles (40–60 nm) showed excellent aqueous stability compared to the PW‐PCPDTBSe nanofibers (d = 20–60 nm, l = 200–1000 nm) and previously synthesized PCPDTBSe nanoparticles (150 nm). Under stimulation from 800 nm near infrared light (3 W, 1 min), the PW‐PCPDTBSe nanoparticles showed greater heat generation (ΔT = 47 °C) compared to bare PCPDTBSe nanoparticles and PW‐PCPDTBSe nanofibers (ΔT = 35 °C for both). Cytotoxicity studies determined that both the PW‐PCPDTBSe nanoparticles and PW‐PCPDTBSe nanofibers displayed no significant toxicity toward either noncancerous small intestinal cells (FHs 74 Int) or colorectal cancer cells (CT26). Photothermal ablation studies confirmed that both the PW‐PCPDTBSe nanoparticles and the PW‐PCPDTBSe nanofibers can be used as localized photothermal agents to eradicate colorectal cancer cells due to their excellent ablation efficiency (>95% cell death at 15 µg/mL concentration). © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1622–1632     

Novel low‐bandgap oligothiophene‐based donor‐acceptor alternating conjugated copolymers: Synthesis,properties, and photovoltaic applications

A series of novel soluble donor‐acceptor low‐bandgap‐conjugated polymers consisting of different oligothiophene (OTh) coupled to electron‐accepting moiety 2‐pyran‐4‐ylidenemalononitrile (PM)‐based unit were synthesized by Stille or Suzuki coupling polymerization. The combination of electron‐accepting PM building block with varied OTh_n (the number of thiophene unit increases from 3 to 5) results in enhanced π–π stacking in solid state and intramolecular charge transfer (ICT) transition, which lead to an extension of the absorption spectra of the copolymers. Cyclic voltammetry measurements and molecular orbital distribution calculations indicate that the highest occupied molecular orbitals (HOMO) energy levels could be fine‐tuned by changing the number of thiophene units of the copolymers, and the resulting copolymers possessed relatively low HOMO energy levels promising good air stability and high‐open circuit voltage (V_oc) for photovoltaic application. Bulk heterojunction photovoltaic devices were fabricated by using the copolymers as donors and (6,6)‐phenyl C₆₁‐butyric acid methyl ester as acceptor. It was found that the highest V_oc reached 0.94 V, and the short circuit currents (J_sc) were improved from 1.78 to 2.54 mA/cm², though the power conversion efficiencies of the devices were measured between 0.61 and 0.99% under simulated AM 1.5 solar irradiation of 100 mW/cm², which indicated that this series copolymers can be promising candidates for the photovoltaic applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2765–2776, 2010     

Enhanced dispersion of nanotubes in organic solvents by donor–acceptor interaction between functionalized poly(phenylacetylene) chains and carbon nanotube walls

Phenylacetylene derivatives containing carbazole ( 1 ) and fluorene ( 2 ) moieties were polymerized by [Rh(nbd)Cl]₂ into corresponding polymers P 1 and P 2 of high molecular weights (M_w ～ 150 × 10³–465 × 10³) in high yields (up to 98%). The polymers were characterized by NMR, IR, UV, PL, and CV techniques. Hybrids of the polymers with multiwalled carbon nanotubes (MWNTs) were prepared by simply mixing the two components in common organic solvents such as dichloromethane. The solvating power of the polymer carrying the electron‐donating carbazolyl pendant (P 1 ) is stronger than that of its counterpart carrying fluorenyl pendant (P 2 ), due to the stronger donor–acceptor (D–A) interaction between the P 1 chains and the MWNT walls. This work clearly manifests that D–A effect plays an important role in the polymer‐aided MWNT dispersion in organic solvents. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4995–5005, 2009     

Synthesis of grafted poly(p‐phenyleneethynylene) with energy donor–acceptor architecture via atom transfer radical polymerization: Towards nonaggregating and hole‐facilitating light‐emitting material

In this contribution, we demonstrate a new effective methodology for constructing highly efficient and durable poly(p‐phenyleneethynylene) (PPE) containing emissive material with nonaggregating and hole‐facilitating properties through the introduction of hole‐transporting blocks into the PPE system as the grafting coils as well as building the energy donor–acceptor architecture between the grafting coils and the PPE backbone. Poly(2‐(carbazol‐9‐yl)ethyl methacrylate) (PCzEMA), herein, is chosen as the hole‐transporting blocks, and incorporated into the PPE system as the grafting coils via atom transfer radical polymerization. The chemical structure of the resultant copolymer, PPE‐g‐PCzEMA, was characterized by NMR and gel permeation chromatography, showing that the desirable copolymer was obtained with the narrow polydispersity. The increased thermal stability of PPE‐g‐PCzEMA was confirmed by thermogravimetric analysis and differential scanning calorimetry along with its macroinitiator. The optoelectronic properties of this copolymer were studied in detail by ultraviolet‐visible absorption, photoluminescence emission and excitation spectra, and cyclic voltammogram (CV). The results indicate that PPE‐g‐PCzEMA exhibits the solid‐state luminescent property dominated by individual lumophores, and also the energy transfer process from the PCzEMA blocks to the PPE backbone with a relatively higher energy transfer efficiency in the solid‐state compared to that of the solution state. Additionally, the hole‐injection property is greatly facilitated due to the presence of PCzEMA, as confirmed by CV profiles. All these data indicate that PPE‐g‐PCzEMA is a good candidate for use in optoelectronic devices. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3776–3787, 2007     

Poly(3‐hexylthiophene)‐b‐poly(3‐cyclohexylthiophene): Synthesis,microphase separation,thin film transistors,and photovoltaic applications

We report the synthesis, characterization, microphase separation, field‐effect charge transport, and photovoltaic properties of regioregular poly(3‐hexylthiophene)‐b‐poly(3‐cyclohexylthiophene) (P3HT‐b‐P3cHT). Two compositions of P3HT‐b‐P3cHT (HcH63 and HcH77) were synthesized with weight‐average molecular weights of 155,500 and 210,800 and polydispersity indices of 1.45 and 1.57, respectively. Solvent‐casted HcH77 was found to self‐assemble into nanowires with a width of 12.5 ± 0.9 nm and aspect ratios of 50–120, as observed by TEM imaging. HcH77 and HcH63 annealed 280 °C were observed by small angle X‐ray scattering (SAXS) and wide angle X‐ray scattering (WAXS) to be microphase‐separated with characteristic length scales of 17.0–21.7 nm. The microphase‐separated domains were shown to be crystalline with interlayer backbone (100) d‐spacings of 1.69 and 1.40 nm, which correspond to the P3HT and P3cHT blocks, respectively. Field‐effect transistors fabricated from P3HT‐b‐P3cHT thin films showed a mobility of holes (0.0019 cm²/Vs) which is independent of thermal annealing. Bulk heterojunction solar cells based on HcH77/fullerene (PC₇₁BM) blend thin films had a maximum power conversion efficiency of 2.45% under 100 mW/cm² AM1.5 solar illumination in air. These results demonstrate that all‐conjugated block copolymers are suitable semiconductors for applications in field‐effect transistors and bulk heterojunction solar cells. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 614–626, 2010     

Direct arylation synthesis of thienoisoindigo‐based low‐band‐gap polymer from asymmetric donor–acceptor monomer

Thienoisoindigo (TIG) moiety has been paid numerous attentions as an excellent acceptor building block in low‐band‐gap polymers. Herein, a new TIG‐dithiophene alternating copolymer (PTIG2T) was successfully synthesized from an asymmetric TIG‐based donor–acceptor (D‐A) monomer via the self‐condensation‐type direct arylation polymerization. PTIG2T exhibited the light absorption over 1000 nm owing to the intramolecular charge transfer in the thin film state, which corresponded to an optical band gap of 1.24 eV. The HOMO and LUMO levels of PTIG2T were determined to be −5.08 and −3.60 eV, respectively. Furthermore, the organic photovoltaic (OPV) with a PTIG2T/PC₆₁BM active layer achieved a power conversion efficiency (PCE) of 3.19%, which is one of the highest PEC achieved by OPVs with TIG‐based materials. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 430–436