Comparison of the mechanical properties of styrene‐based ionomers containing either crown ether or pentaethylene glycol with those of underneutralized ionomers

Dynamic mechanical properties of styrene‐based ionomers containing varying amounts of either 15‐crown‐5 ether (CE) or pentaethylene glycol (PG) are compared with those of ionomers of varying degree of neutralization (ND). The cluster T_g (T_g,c) and ionic modulus of the ionomers decrease with increasing amount of CE or PG or decreasing ND. Thus, we propose that the CE binds Na⁺ strongly to form a large‐sized complex. Thus, the electrostatic interactions between charges decrease, leading to lower T_g,c. For the PG‐containing ionomers, the PG acts as polar plasticizer, further lowing the T_g,c. In the case of the underneutralized ionomers, the T_g,c is reduced by the existence of both relatively weak hydrogen bonds between carboxylic acid groups and relatively strong ionic bonds between ion pairs in the multiplets. The small‐angle X‐ray scattering results are also supportive of the above interpretations. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1358–1367     

Dynamic mechanical properties of polystyrene ionomers containing both carboxylate and sulfonate anionic groups

Polystyrene‐based ionomers possessing sodium methacrylate (MA) and sodium styrenesulfonate (SS) units in each polymer chain [poly(styrene‐co‐methacrylate‐co‐styrenesulfonate) (PSMA‐SS)] were synthesized. The dynamic mechanical properties of PSMA‐SS ionomers were studied and compared with those of styrene ionomers containing only MA (PSMA ionomer) or SS (PSS ionomer) units. It was observed that the ionic moduli of PSMA‐SS ionomers depended directly on the total ion content and that the ionic modulus was highest for the PSMA ionomer and lowest for the PSMA‐SS ionomer. The matrix T_gs of the three ionomer systems were found to be similar to each other; the cluster T_g of PSMA‐SS ionomer was higher than that of PSS ionomer at low SS contents but became closer to each other at high SS contents. In addition, the small‐angle X‐ray scattering study revealed that the multiplet size might be in the following order: PSMA‐SS > PSS > PSMA. This implied that at the same ion content, the fractions of cluster regions were smallest for PSMA‐SS ionomer in comparison with those of PSS or PSMA ionomers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

SAXS study on ionic aggregates of styrene‐isoprene‐sulfonated isoprene terpolymer ionomer

The small‐angle X‐ray scattering profile of styrene‐isoprene‐sulfonated isoprene terpolymer ionomers was studied to clarify the structure of ionic aggregates at ambient temperature as a function of the degree of neutralization of Na or Mg cations. An ionic cluster peak was observed for ionomers with a degree of neutralization greater than 25%. The ionic cluster peak was analyzed by the modified hard sphere model proposed by Yarusso and Cooper [Macromolecules, 1983, 16, 1871], and the size of the ion cluster, the closest approach distance between the clusters, and the average system volume per ion cluster were evaluated by a curve‐fitting method. The size of the ion clusters of the ionomer with monovalent Na cation increased with the degree of neutralization, but for divalent Mg cation slightly changed. The number of ion clusters of the styrene‐isoprene‐sulfonated isoprene ionomer with Na and Mg cations characteristically increased with the neutralization. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1307–1311, 2000     

Wettability of poly(styrene‐co‐acrylate) ionomers improved by oxygen‐plasma source ion implantation

The surfaces of poly(styrene‐co‐acrylic acid) copolymers and their Na‐ and Cs‐neutralized ionomers were modified by O₂‐plasma source ion implantation (PSII) treatment to improve the surface wettability. The changes in the surface wettability, composition, and structure upon the PSII treatment were examined with contact‐angle measurements and X‐ray photoelectron spectroscopy. The untreated surfaces of the acid copolymers and ionomers exhibited different surface energies; this implied clearly that the type of ion species affects the surface hydrophilicity. Also, the PSII treatment induced oxygen‐containing groups to reside on the surface and ionic groups to come out toward the surface; this made the surfaces of the ionomers more hydrophilic as compared with that of the acid copolymers. The ionomers also showed slow hydrophobic recovery. Thus, it was suggested that the reduced mobility of the polymer chain because of the presence of ionic aggregates results in restricted reorientation of oxygen‐containing groups. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1791–1797, 2003     

Clustering in carboxylated polysulfone ionomers: A characterization by dynamic mechanical and small-angle X-ray scattering methods

The dynamic mechanical properties and morphology of carboxylated polysulfone ionomers were investigated by dynamic mechanical thermal analysis and small-angle X-ray scattering (SAXS) techniques. It was found that at 25 mol % of ions, ionomers show two glass transitions: one at about 200 °C (the matrix T_g) and the other at about 235 °C (the cluster T_g). It was also found that with increasing ion content up to about 37 mol %, the matrix T_g shifted to higher temperatures and the size of tan δ peak decreased. The cluster T_g did not change. From the results, it is suggested that even at high ion content, the ionomers contain a significant amount of unclustered material, but that the increase in the ion content does not increase the amount of clustered material. SAXS profiles showed the ionic peak, which represents the presence of multiplets in the cluster regions. In addition, the difference in the matrix and cluster T_g's of this ionomer system was found to be about 35°. Thus, it is postulated that ionic group aggregation is subject to steric hindrance owing to the bulkiness of benzene ring, and tension on polymer chains surrounding the multiplet owing to chain rigidity, which limit the size and stability of the multiplet significantly. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 3226–3232, 1999     

Reversible gelation of poly(dimethylsiloxane) with ionic and hydrogen‐bonding substituents

Poly(dimethylsiloxane) copolymers containing a small fraction of carboxylic acid or Zn‐carboxylate groups were prepared and compared regarding reversible gelation by hydrogen‐bonding and ion‐pair interaction. The polymers were synthesized by condensation of a t‐butylcarboxylate functionalized dichlorosilane with an α,ω‐dihydroxy‐poly(dimethylsiloxane), followed by thermal cleavage of the ester bond. Neutralization of the resulting carboxylic acid substituents was achieved by addition of Zn (acac)₂. Reversible crosslinking was investigated by step stress and oscillating shear experiments. The carboxylic acid containing poly(dimethylsiloxane) became rubberlike upon increasing the temperature and liquified again when it was brought back to room temperature. This observation has been explained tentatively by segregation of the carboxylic acid groups into polar domains at high temperatures [i.e., a behavior like it is observed for systems with a lower critical solution temperature (LCST)]. At ambient temperature, the carboxylic acid groups undergo hydrogen bonding to the Si–O–Si backbone. Clustering of the carboxylic acid groups occurs only as these hydrogen bonds break upon raising temperature. Moisture was found to have a strong influence on the reversal of the crosslinking. Addition of zinc acetylacetonate resulted in the formation of an elastic network already at ambient conditions consistent with the concept of ionomers which undergo reversible gelation by formation of ion‐pair multiplets and clusters in the hydrophobic polymer matrix in particularly at low temperatures. At high temperature, both the carboxylic acid and the carboxylate sample exhibited a rather similar viscoelastic behavior consistent with a common structure where transient crosslinks are formed by clusters of the carboxylic acid and the carboxylate groups. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 485–495, 1999     

Influence of ionic association on the nonisothermal crystallization kinetics of sodium sulfonate poly(butylene succinate) ionomers

We evaluated the relationship between the ionic substituents and nonisothermal crystallization behavior in poly(butylene succinate) (PBS) ionomers, synthesized by the introduction of sulfonated dimethyl fumarate (SDMF) with sodium sulfonate. In addition, we investigated the effect of sodium ions on the molecular structure of the PBS backbone by solid‐state ²³Na NMR analysis. Sodium ion aggregates (multiplets) was predominately created with the ionic group concentration, and melt rheology and dynamic melt analysis results showed that multiplet formation induced not only remarkable heterogeneity, but also a high degree of clustering in the PBS chains. At low ionic group concentration, well dispersed multiplets behaved as effective nuclei during the crystallization of the PBS ionomer and accelerated the rate of crystallization. As ionic group concentration grew higher, crystallization rates decreased due to hindered chain mobility by clusters consisting of numerous multiplets. A combined Ozawa and Avrami equation proved to be more effective than the Ozawa equation in describing the nonisothermal crystallization kinetics of PBS and its ionomers. The observed nucleation activity indicates that the nonisothermal crystallization rate is not directly proportional to the ionic group concentration. Superior nucleation activity was observed in PBS ionomer containing 1 mol % SDMF. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 925–937, 2008     

Mechanical properties and morphology of homoblends of a poly(ethyl acrylate) ionomer having one ion pair per ionic repeat unit and a poly(ethyl acrylate) ionomer having two ion pairs

The mechanical properties and morphology of homoblends of poly(ethyl acrylate‐co‐acrylate) (PEAA) having one ion pair per ionic monomer repeat unit and poly(ethyl acrylate‐co‐itaconate) (PEAITA) having two ion pairs were investigated. It was found that the compositional variation in the ionomer homoblends did not affect the matrix or cluster glass transition temperatures of the two ionomers of the homoblends. It was also observed that the ionomer homoblends showed two ionic plateaus and that the changes in the two ionic moduli were directly related to the relative amounts of the two ionomers. The ionic moduli calculated with the model for filler‐dispersed materials were found to fit the experimental data to a great extent. Therefore, it was suggested that the PEAITA/PEAA ionomer homoblends were filler‐containing composite materials rather than miscible blends. In the X‐ray scattering study, it was observed that the morphology of the ionomer homoblends was not affected by mixing. The results obtained in this work might be useful for the modification of the storage moduli of copolymers in a certain temperature range without the alteration of their processing temperatures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1045–1052, 2007.     

Side‐chain functionalized liquid‐crystalline polymers and blends. IX.* Phase behavior and structure of comb‐shaped liquid‐crystalline ionomers containing calcium ions

Liquid‐crystalline (LC) ionomers containing 2–15 mol % calcium ions were synthesized by the exchange reaction between the nematic LC copolymer, bearing oxycyanobiphenyl mesogenic groups, and the carboxyl groups of acrylic acid, with calcium acetate. The incorporation of 2–3 mol % Ca ions in the LC copolymer leads to some rise in the clearing point and glass‐transition temperature. A further increase in the concentration of metal ions (>5 mol %) is accompanied by induction of the smectic A phase where clearing point and glass‐transition temperatures keep constant values. Phase behavior of the LC ionomers may be understood on the basis of a structural model that considers the dual role of calcium ions in a polymer matrix. Metal ions act as points of noncovalent electrostatic binding of the polymer chains and are capable of forming larger ionic associates (multiplets). The comparison of the phase behavior of sodium and calcium containing LC ionomers shows that the formation of ionic links may lead to the growth of structure defects suppressing a positive influence of charged groups on the mesophase clearing temperature. The orientation behavior of the LC ionomers in the magnetic field was studied. It was shown that the incorporation of calcium ions (3 mol %) in the LC copolymer matrix leads to the growth of orientation order parameter S of the nematic phase. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3953–3959, 2001     

Ionic aggregation in random copolymers containing phosphonium ionic liquid monomers

Copolymers of n‐butyl acrylate and phosphonium ionic liquid monomers possessing various alkyl substituents and counterions were synthesized through a combination of conventional free radical copolymerization and anion exchange. Differential scanning calorimetry and dynamic mechanical analysis provided the thermal and mechanical properties of these phosphonium cation‐containing random copolymers. Factors including alkyl chain length of phosphonium substituents, counterion type, as well as ionic concentration significantly influenced the association of phosphonium cations. Phosphonium ionomers with trialkyl substituents on phosphonium cations did not display the characteristic small‐angle X‐ray scattering peak, suggesting the absence of ionic clusters. However, low q peaks in wide‐angle X‐ray diffraction was indicative of significant concentration fluctuations wherein the ionic monomeric units associated. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Reactivity and catalytic activity of cationic lonomers for the nucleophilic substitution reactions

Polystyrene-based crosslinked cationic ionomers containing ammonium or phosphonium chlorides (AxRCI and PxBuCI) were reacted with decyl methanesulfonate. The kinetic data were correlated with the swelling behavior of the ionomers and the solution viscosity of the corresponding linear ionomers. The reactivity of the ionomers was independent of the particle size of the ionomer beads, indicating no diffusion control of the reaction. The solvent and the ion content of the ionomers greatly affect the reactivity. In nonpolar solvents with a low acceptor number, A_N, such as toluene, the aggregation of ionic groups with an increasing ion content reduces the reactivity. A solvent with a high value of A_N, such as chloroform, led a very low reactivity independent of the ion content. Aprotic polar solvent, such as acetonitrila, promoted the dissociation of the ionic groups and furnished a relatively high reactivity independent of the ion content. Several catalytic substitution reactions were carried out under liquid-solid-solid triphase conditions. The kinetic results were accounted for in terms of slow nucleophile transport and fast chemical reaction within the ionomer particles. © 1994 John Wiley & Sons, Inc.     

Fourier transform infrared/attenuated total reflectance analysis of water diffusion in poly[styrene‐b‐isobutylene‐ b‐styrene] block copolymer membranes

A Fourier transform infrared/attenuated total reflectance technique was used to study the diffusion of water through poly(styrene‐b‐isobutylene‐b‐styrene) block copolymers (BCPs), as well as sulfonated (H⁺) and Na⁺‐sulfonated ionomer versions. Diffusion data were collected and interpreted for these membranes versus polystyrene block composition, degree of sulfonation, Na⁺ ion content in the ionomers, and the effect of initially dry versus prehydrated conditions. An “early time” diffusion coefficient, D, decreased with increasing percent polystyrene for a series of unmodified BCPs. D decreased with increasing degree of sulfonation, and with increasing ion content for the Na⁺‐exchanged samples and this was interpreted in terms of diffusion limitations caused by a strong tendency for ion hydration. The method also yielded information relating to the time evolution of water structure from the standpoint of degree of intermolecular hydrogen bonding. Membrane prehydration causes profound increases in D for both the unmodified BCP and sulfonated samples, as in plasticization. The simultaneous acquisition of information relating to interactions between water molecules and interactions of water molecules with functional groups on the host polymer matrix offers more information than conventional diffusion measurement techniques that simply count transported molecules. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 764–776, 2005     

Solid‐state NMR analyses of the crystalline–noncrystalline structure and its thermal changes for ethylene ionomers

The crystalline–noncrystalline structure and its structural changes from thermal treatments for ethylene ionomers have been investigated with solid‐state ¹³C and ²³Na NMR spectroscopy. ¹³C spin–lattice relaxation time (T_1C) measurements reveal that as‐received ethylene ionomers have much enhanced molecular mobility in the crystalline region in comparison with conventional polyethylene samples. By appropriate annealing, however, polyethylene‐like morphological features reflecting T_1C behavior can also be observed. ¹³C spin–spin relaxation time (T_2C) measurements for the noncrystalline region reveal the existence of two components with different T_2C values, and these two components have been assigned to the crystalline–amorphous interfacial and rubbery–amorphous components. These results indicate that the structure of the major part of the noncrystalline region in the ethylene ionomers is similar to that of bulk‐crystallized polyethylene samples, regardless of possible ionic aggregates. The origin of the lower temperature endothermic peak in the heating process of the differential scanning calorimetry curve observed for the as‐received sample has also been examined somewhat in detail. As a result, it is proposed that the melting of smaller crystallites produced during storage at room temperature is the origin of the lower temperature peak. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1142–1153, 2002     

Temperature‐induced aggregation of the copolymers of N‐isopropylacrylamide and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate in aqueous solutions

A series of random copolymers of N‐isopropylacrylamide (NIPAM) and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate (AMPS) was synthesized by free‐radical copolymerization. The content of AMPS in the copolymers ranged from 1.1 to 9.6 mol %. The lower critical‐solution temperature (LCST) of copolymers in water increased strongly with an increasing content of AMPS. The influence of polymer concentration on the LCST of the copolymers was studied. For the copolymers with a higher AMPS content, the LCST decreased faster with an increasing concentration than for copolymers with a low content of AMPS. For a copolymer containing 1.1 mol % of AMPS the LCST dropped by about 3 °C when the concentration increased from 1 to 10 g/L, whereas for a copolymer containing 9.6 mol % of AMPS the LCST dropped by about 10 °C in the concentration range from 2 to 10 g/L. It was observed that the ionic strength of the aqueous polymer solution very strongly influences the LCST. This effect was most visible for the copolymer with the highest content of AMPS (9.6 mol %) for which an increase in the ionic strength from 0.2 to 2.0 resulted in a decrease in the LCST by about 27 °C (from 55 to 28 °C), whereas for the copolymer containing 1.1 mol % of AMPS the LCST decreased only by about 6 °C (from 37 to 31 °C) when the ionic strength increased from 0.005 to 0.3. The reactivity ratios for the AMPS and NIPAM monomer pairs were determined using different methods. The values of r_AMPS and r_NIPAM obtained were 11.0–11.6 and 2.1–2.4, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2784–2792, 2001     

3,4-聚异戊二烯的磺化反应及其离聚体的结构研究

本工作合成了磺化的3,4-聚异戊二烯及其离子聚合体,IR和NMR谱图证明对3,4-聚异戊二烯的磺化反应是成功的,并且磺酸基团主要与3,4-链节的侧基双键发生反应。WAXD对磺化3,4-聚异戊二烯及其离聚体的研究表明,磺化度的增加使离聚体的结晶能力降低,SAXS结果表明,在离子含量为3.29mol％的离聚体中,未观察到离子簇聚集,只观察到多重离子对的散射。     

Utilizing thiol–ene chemistry for crosslinked nickel cation‐based anion exchange membranes

Metal cation‐based anion exchange membranes (AEMs) are a unique class of materials that have shown potential to be highly stable AEMs with competitive conductivities. Here, we expand upon previous work to report the synthesis of crosslinked nickel cation‐based AEMs formed using the thiol–ene reaction. These thiol–ene‐based samples were first characterized for their morphology, both with and without nickel cations, where the nickel‐containing membranes demonstrated a disordered scattering peak characteristic of ionic clusters. The samples were then characterized for their water uptake, chemical and mechanical stability, and conductivity. They showed a combination of high water content and extreme brittleness, which also resulted in fairly low conductivity. The brittleness resulted from large water swelling as well as the need for each nickel cation to act as a crosslinker, necessary with the current nickel‐coordination chemistry. Therefore, increasing the ion exchange capacity (IEC) for these types of AEMs, important for enhancing conductivity, also increased the crosslink density. The low conductivity and brittleness seen in this work demonstrated the need to develop non‐crosslinking metal‐complexes. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 328–339     

Novel multiblock‐co‐ionomers as potential polymer electrolyte membrane materials

In this contribution a series of novel multiblock‐co‐ionomers consisting of hydrophobic (partially fluorinated) and hydrophilic (sulfonated) domains has been prepared and characterised in terms of their applicability as fuel cell membranes. The synthesis of these multiblock‐co‐ionomers is a four‐step procedure including (1) the sulfonation of the monomer 4,4′‐difluorodiphenylsulfone, (2) the preparation of hydrophilic telechelic macromonomers by molecular‐weight controlled step‐growth polycondensation of the sulfonated monomer with various bis(thio)phenols, (3) the preparation of a hydrophobic telechelic macromonomer and (4) the coupling of both telechelic macromonomers to yield microphase‐separated block‐co‐ionomers. This study focuses on the investigation of the influence of various linkage groups and atoms within the hydrophilic domains of the multiblock‐co‐ionomers. Both the telechelic macromonomers and the multiblock‐co‐ionomers were structurally investigated by ¹H‐ and ¹⁹F‐NMR spectroscopy and gel permeation chromatography (GPC). All multiblock‐co‐ionomers of this series could be cast into membranes and their membrane properties (ion‐exchange capacity, specific resistance, swelling ratio, water uptake, thermal and oxidative stability) were measured and discussed in dependence of the various linkage groups within the hydrophilic domains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5237–5255, 2007     

Correlating backbone‐to‐backbone distance to ionic conductivity in amorphous polymerized ionic liquids

The morphology and ionic conductivity of poly(1‐n‐alkyl‐3‐vinylimidazolium)‐based homopolymers polymerized from ionic liquids were investigated as a function of the alkyl chain length and counterion type. In general, X‐ray scattering showed three features: (i) backbone‐to‐backbone, (ii) anion‐to‐anion, and (iii) pendant‐to‐pendant characteristic distances. As the alkyl chain length increases, the backbone‐to‐backbone separation increases. As the size of counterion increases, the anion‐to‐anion scattering peak becomes apparent and its correlation length increases. The X‐ray scattering features shift to lower angles as the temperature increases due to thermal expansion. The ionic conductivity results show that the glass transition temperature (T_g) is a dominant, but not exclusive, parameter in determining ion transport. The T_g‐independent ionic conductivity decreases as the backbone‐to‐backbone spacing increases. Further interpretation of the ionic conductivity using the Vogel–Fulcher–Tammann equation enabled the correlation between polymer morphology and ionic conductivity, which highlights the importance of anion hoping between adjacent polymer backbones. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Phosphorus‐containing telechelic polyester‐based ionomer: Facile synthesis and antidripping effects

The ionomer concept was introduced to the field of flame‐retardant polyesters for the first time. The ionic monomer, sodium salt of 2‐hydroxyethyl 3‐(phenylphosphinyl)propionate (SHPPP), was synthesized by selective esterification of 3‐(hydroxyphenylphosphinyl)propionic acid with ethylene glycol, followed by neutralization with sodium carbonate anhydrous. SHPPP was characterized with ¹H, ¹³C, and ³¹P NMR spectroscopy, Fourier transform infrared spectroscopy, and X‐Ray photoelectron spectroscopy. Poly(ethylene terephthalate)‐based ionomers containing terminal units derived from this ionic monomer, were synthesized by melt polycondensation. The chemical structure of the ionomers was characterized with ¹H, ¹³C, and ³¹P NMR spectroscopy. The effects of SHPPP on the thermal properties and melting behaviors of the ionomers were investigated by thermogravimetric analysis and differential scanning calorimetry. The flammability of the ionomers was characterized by the limiting oxygen index test. The test results show that the ionomers themselves possess both excellent flame retardancy and antidripping properties. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2994–3006, 2008     

Membranes from poly(aryl ether)‐based ionomers containing multiblock segments of randomly distributed nanoclusters of 18 sulfonic acid groups

Multiblock copolymers 1a (M_n = 31,500–47,400) of sulfonated poly(aryl ether)s were synthesized by polycondensation of 4,4′‐difluorobenzophenone (DFBP), bis(4‐hydroxyphenyl)sulfone (BHPS), and an hydroxy‐terminated sulfonated oligomer, which was synthesized from DFBP and 2,2′,3,3′,5,5′‐hexaphenyl‐4,4′‐dihydroxybiphenyl a . The copolymerization of trimeric monomer b with DFBP and BHPS gave a series of copolymers 1b (M_n = 26,200–45,900). The copolymers were then sulfonated with chlorosulfonic acid to give ionomers 3a with hydrophilic multiblock segments and ionomers 3b with segments containing clusters of 18 sulfonic acid groups. The proton exchange membranes cast from ionomers 3a and 3b were characterized with regard to thermal stability, water uptake, proton conductivity, and morphology. Transmission electron microscopy images of 3a‐1 and 3b‐1 revealed a phase separation similar to that of Nafion that may explain their higher proton conductivities compared with randomly sulfonated copolymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4762–4773, 2009