Supramolecular complexes of poly(3‐Hexylthiophene)‐block (and random)‐poly[3‐(2‐(6‐carboxyhexyl)methyl)thiophene] copolymers with perylene bisimide

Block and random copolymers of poly(3‐hexylthiophene) and poly[3‐(2‐(6‐carboxyhexyl)methyl)thiophene] with side‐chain carboxylic functionality ((P3HT‐b‐P3COOH) and (P3HT‐r‐P3COOH) were developed by Grignard Metathesis (GRIM) polymerization. The carboxylic functionality was introduced in the side chain via the oxazoline route. Both the block and random polythiophene copolymers were complexed with pyridine functionalized perylene bisimide to obtain supramolecular block and random polymer complexes. The complex formation in both systems was confirmed by ¹H NMR, WXRD and SAXS studies. An expansion of d spacing upon complex formation was observed in both the block and random copolymer, which could be traced by WXRD. Hole and electron mobilities measured for the supramolecular complexes indicated values which were higher by an order of magnitude for the supramolecular block complex (μ_h ≈ 2.9 × 10⁻⁴ cm²/Vs; μ_e ≈ 3.1 × 10⁻⁶ cm²/Vs) as compared to the random (μ_h ≈ 1.4 × 10⁻⁵ cm²/Vs; μ_e ≈ 4.7 × 10⁻⁷ cm²/Vs) copolymer. These results are indicative of the higher degree of disorder prevailing in the films of random copolymer system compared to the block copolymer. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1574–1583     

Charge transport properties of triphenylamine‐pendant polypeptide

The structurally ordered polymer, triphenylamine‐pendant polypeptide (PATPA: poly[γ‐4‐(N,N‐diphenylamino‐phenyl)‐L ‐glutamine]), was prepared in order to obtain high hole mobility and high thermal stability. The hole mobility obtained for PATPA (ca. 10⁻⁵ cm²/Vsec) at room temperature is higher than that for poly(N‐vinylcarbazole) (PVK) (ca. 10⁻⁷ cm²/Vsec) or that of carbazole‐pendant polypeptide (PCLG) (ca. 10⁻⁸ cm²/Vsec). These results are supported by thermally stimulated current (TSC) measurements because the TSC can be correlated with the mobility. The glass‐transition temperature (T_g) of PATPA was estimated to be about 130° by differential scanning calorimetry (DSC). From these results, PATPA is an alternative candidate as a photoconductive polymer with high thermal stability and high hole mobility. The ordered structure along the main chain is thought to facilitate hole transport. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 362–368, 2000     

Synthesis and characterization of indenofluorene‐based copolymers containing 2,5‐bis(2‐thienyl)‐N‐arylpyrrole for bulk heterojunction solar cells and polymer light‐emitting diodes

Two novel alternating π‐conjugated copolymers, poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P1 ) and poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(p‐octylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P2 ), were synthesized via the Suzuki coupling method and their optoelectronic properties were investigated. The resulting polymers P1 and P2 were completely soluble in various common organic solvents and their weight‐average molecular weights (M_w) were 5.66 × 10⁴ (polydispersity: 1.97) and 2.13× 10⁴ (polydispersity: 1.54), respectively. Bulk heterojunction (BHJ) solar cells were fabricated in ITO/PEDOT:PSS/polymer:PC₇₀BM(1:5)/TiO_x/Al configurations. The BHJ solar cell with P1 :PC₇₀BM (1:5) has a power conversion efficiency (PCE) of 1.12% (J_sc= 3.39 mA/cm², V_oc= 0.67 V, FF = 49.31%), measured using AM 1.5 G solar simulator at 100 mW/cm² light illumination. We fabricated polymer light‐emitting diodes (PLEDs) in ITO/PEDOT:PSS/emitting polymer:polyethylene glycol (PEG)/Ba/Al configurations. The electroluminescence (EL) maxima of the fabricated PLEDs varied from 526 nm to 556 nm depending on the ratio of the polymer to PEG. The turn‐on voltages of the PLEDs were in the range of 3–8 V depending on the ratio of the polymer to PEG, and the maximum brightness and luminance efficiency were 2103 cd/m² and 0.37 cd/A at 12 V, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3169–3177, 2010     

Effects of different acid functional groups on proton conductivity of polymer‐1,2,4‐triazole blends

Proton transfer reactions under anhydrous conditions have attracted remarkable interest due to chemical energy conversions in polymer electrolyte membrane fuel cells. In this work, 1H‐1,2,4‐triazole (Tri) was used as a proton solvent in different polymer host matrices such as Poly(vinylphosphonic acid) (PVPA), and poly(2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid) (PAMPS). PVPATri_x and PAMPSTri_x electrolytes were investigated where x is the molar ratio of Tri to corresponding polymer repeat unit. The interaction between polymer and Tri was studied via FTIR spectroscopy. Thermogravimetry analysis and differential scanning calorimetry were employed to examine the thermal stability and homogeneity of the materials, respectively. PVPATri_1.5 showed a maximum water‐free proton conductivity of 2.3 × 10^?3 S/cm at 120 °C and that of PAMPSTri₂ was 9.3 × 10^?4 S/cm at 140 °C. The results were interpreted in terms of different acidic functional groups and composition. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3315–3322, 2006     

Poly(thienylene‐vinylene‐thienylene) with cyano substituent: Synthesis and application in field‐effect transistor and polymer solar cell

A novel conjugated polymer, poly(thienylene‐vinylene‐thienylene) with cyano substituent ( CN‐PTVT ) was synthesized via Stille coupling for the application in air stable field‐effect transistor and polymer solar cell. The polymer was characterized by ¹H NMR, elemental analysis, UV‐vis absorption and photoluminescence spectroscopy, TGA, cyclic voltammetry and XRD analysis. CN‐PTVT exhibits a good thermal stability with 5% weight loss at 306 °C. The FET hole mobility of the polymer reached 5.9 × 10^?3 cm² V^?1 s^?1 with I_on/I_off ratio of 4.9 × 10⁴, which is one of the highest performance among the air‐stable amorphous polymers. The polymer solar cell based on CN‐PTVT as donor and PCBM as acceptor shows a relatively high open‐circuit voltage of 0.82 V and a power conversion efficiency of 0.3% under the illumination of AM1.5, 100 mW/cm². © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4028–4036, 2009     

Poly(4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene vinylene): Synthesis,optical and photovoltaic properties

A new benzodithiophene (BDT)‐based polymer, poly(4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene vinylene) (PBDTV), was synthesized by Pd‐catalyzed Stille‐coupling method. The polymer is soluble in common organic solvents and possesses high thermal stability. PBDTV film shows a broad absorption band covering from 350 nm to 618 nm, strong photoluminescence peaked at 545 nm and high hole mobility of 4.84 × 10^?3 cm²/Vs. Photovoltaic properties of PBDTV were studied by fabricating the polymer solar cells based on PBDTV as donor and PC₇₀BM as acceptor. With the weight ratio of PBDTV: PC₇₀BM of 1:4 and the active layer thickness of 65 nm, the power conversion efficiency of the device reached 2.63% with V_oc = 0.71 V, I_sc = 6.46 mA/cm², and FF = 0.57 under the illumination of AM1.5, 100 mW/cm². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1822–1829, 2010     

Mesogen‐controlled ion channel of star‐shaped hard–soft block copolymers for solid‐state lithium‐ion battery

Novel star‐shaped hard–soft triblock copolymers, 4‐arm poly(styrene)‐block‐poly [poly(ethylene glycol) methyl ethyl methacrylate]‐block‐poly{x‐[(4‐cyano‐4′‐biphenyl) oxy] alkyl methacrylate} (4PS‐PPEGMA‐PMAxLC) (x = 3, 10), with different mesogen spacer length are prepared by atom‐transfer radical polymerization. The star copolymers comprised three different parts: a hard polystyrene (PS) core to ensure the good mechanical property of the solid‐state polymer, and a soft, mobile poly[poly(ethylene glycol) methyl ethyl methacrylate] (PPEGMA) middle sphere responsible for the high ionic conductivity of the solid polyelectrolytes, and a poly{x‐[(4‐cyano‐4′‐biphenyl)oxy]alkyl methacrylate} with a birefringent mesogens at the end of each arm to tuning the electrolytes morphology. The star‐shaped hard–soft block copolymers fusing hard PS core with soft PPEGMA segment can form a flexible and transparent film with dimensional stability. Thermal annealing from the liquid crystalline states allows the cyanobiphenyl mesogens to induce a good assembly of hard and soft blocks, consequently obtaining uniform nanoscale microphase separation morphology, and the longer spacer is more helpful than the shorter one. There the ionic conductivity has been improved greatly by the orderly continuous channel for efficient ion transportation, especially at the elevated temperature. The copolymer 4PS‐PPEGMA‐PMA10LC shows ionic conductivity value of 1.3 × 10^?4 S cm^?1 (25 °C) after annealed from liquid crystal state, which is higher than that of 4PS‐PPEGMA electrolyte without mesogen groups. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4341–4350     

Investigation of proton conductivity of anhydrous proton exchange membranes prepared via grafting vinyltriazole onto alkaline‐treated PVDF

This work uses a simple “grafting through” approach in the preparation of anhydrous poly(vinylidene fluoride) (PVDF)‐g‐PVTri polymer electrolyte membranes (PEMs). Alkaline‐treated PVDF was used as a macromolecule in conjunction with vinyltriazole in the graft copolymerization. The obtained polymer was subsequently doped with triflic acid (TA) at different stoichiometric ratios with respect to triazole units and the anhydrous PEMs (PVDF‐g‐PVTri‐(TA)_x) were prepared. All samples were characterized by FTIR and ¹H NMR. The composition of PVDF‐g‐PVTri was determined by energy dispersive spectroscopy. Thermal properties of the membranes were examined by thermogravimetric analysis and differential scanning calorimetry. The surface roughness and morphology of the membranes were studied using atomic force microscopy, X‐ray diffraction, and scanning electron microscopy. PVDF‐g‐PVTri‐(TA)₃ (C3‐TA₃) with a degree of grafting of 47.22% showed a maximum proton conductivity of 0.09 S cm^?1 at 150 °C and anhydrous conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1885–1897     

Polymer electrolyte membranes by in situ polymerization of poly(ethylene carbonate‐co‐ethylene oxide) macromonomers in blends with poly(vinylidene fluoride‐co‐hexafluoropropylene)

Salt‐containing membranes based on polymethacrylates having poly(ethylene carbonate‐co‐ethylene oxide) side chains, as well as their blends with poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP), have been studied. Self‐supportive ion conductive membranes were prepared by casting films of methacrylate functional poly(ethylene carbonate‐co‐ethylene oxide) macromonomers containing lithium bis(trifluorosulfonyl)imide (LiTFSI) salt, followed by irradiation with UV‐light to polymerize the methacrylate units in situ. Homogenous electrolyte membranes based on the polymerized macromonomers showed a conductivity of 6.3 × 10^?6 S cm^?1 at 20 °C. The preparation of polymer blends, by the addition of PVDF‐HFP to the electrolytes, was found to greatly improve the mechanical properties. However, the addition led to an increase of the glass transition temperature (T_g) of the ion conductive phase by ～5 °C. The conductivity of the blend membranes was thus lower in relation to the corresponding homogeneous polymer electrolytes, and 2.5 × 10^?6 S cm^?1 was recorded for a membrane containing 10 wt % PVDF‐HFP at 20 °C. Increasing the salt concentration in the blend membranes was found to increase the T_g of the ion conductive component and decrease the propensity for the crystallization of the PVDF‐HFP component. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 79–90, 2007     

Spontaneous formation of hierarchical proton‐conductive structures in sulfonated poly(p‐phenylene terephthalamide) copolymer films

Two partially sulfonated copolymers of poly(p‐phenylene terephthalamide) were studied; the sulfonated diamine to nonsulfonated diamine ratios were x = 1 and x = 2. Polymer solutions in water demonstrated lyotropic liquid‐crystalline behavior, with the critical concentration for nematic phase formation being around 0.7 wt %. Films of these copolymers could be considered for fuel‐cell applications. The in‐plane proton conductivities were of the order of 10^?3 to 10^?2 S cm^?1 between 20 and 90 °C. Increasing the sulfonation level resulted in a more conductive material. Spontaneous alignment of the polymer occurred during film formation, as revealed by X‐ray diffraction. Scattering along the polymer backbone was observed perpendicular to the film, implying that the polymer chains were homeotropically aligned with respect to the film. The average degree of alignment was determined to be 0.66 and 0.77 for x = 1 and x = 2, respectively. Evidence of secondary layering within the plane of the film was seen in SEM images. These layers could provide a pathway for proton conduction to occur within the plane of the film. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 666–676, 2007     

Thin poly(ionic liquid) and poly(vinylidene fluoride) blend films with ferro‐ and piezo‐electric polar γ‐crystals

Ferro‐ and piezo‐electric poly(vinylidene fluoride) (PVDF) thin film is reported to be obtained by using a poly(ionic liquid) (PIL) [poly(2‐(dimethylamino)ethyl methacrylate) methyl chloride quaternary salt] through solution route. The short range interactions between localized cationic ions of PIL and polar >CF₂ of PVDF are responsible for modified polar γ‐PVDF (T₃GT₃Ḡ) formation. Modification in chain conformation of PVDF is confirmed by FTIR, XRD, and DSC studies suggesting the miscible PVDF–PIL (PPIL) blend. Up to 40 wt % loading of PIL in PVDF matrix enhances relative intensity of γ‐phase up to 50% in the entire crystalline phase. The P‐E hysteresis loop of PVDF‐PIL blends at 25 wt % PIL loading (PPIL‐25) thin film at sweep voltage of ±50 V shows excellent ferroelectric property with nearly saturated high remnant polarization ∼6.0 µC cm⁻² owing to large proportion of γ‐PVDF. However, non‐polar pure PVDF thin film shows unsaturated hysteresis loop with 1.4 µC cm⁻² remnant polarization. The operation voltage decreases effectively because of the polar γ‐phase formation in PPIL blended film. High‐sensitivity piezo‐response force microscopy shows electromechanical switching property at low voltages in PPIL‐25 thin films through local switching measurements, making them potentially suitable as ferroelectric tunnel barriers. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 795–802     

Bay‐annulated indigo based near‐infrared sensitive polymer for organic solar cells

A new conjugated polymer (PBAIIDTT) based on bay‐annulated indigo and indacenodithieno[3,2‐b]thiophene was designed, synthesized, and characterized. PBAIIDTT shows strong absorption in 400–500 and 600–800 nm, and its HOMO and LUMO energy levels are −5.45 eV and −3.65 eV, respectively. In organic field‐effect transistors, the polymer exhibits a relatively high hole mobility of 0.39 cm² V⁻¹ s⁻¹. PBAIIDTT was added to poly(3‐hexylthiophene) (P3HT) and phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) based organic solar cells. Ternary blend solar cells with 10% PBAIIDTT show an increased short circuit current density due to the broadened photocurrent generated in the near‐infrared region, and a power conversion efficiency of 3.78%, which is higher than that of the P3HT:PC₆₁BM binary control devices (3.33%). © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 213–220     

Surface‐initiated ring‐opening polymerization of p‐dioxanone on Wang resin bead

Biodegradable poly(p‐dioxanone) (PPDO) was formed on Wang resin surface by surface‐initiated ring‐opening polymerization (SI‐ROP). The SI‐ROP of p‐dioxanone (PDO) was achieved by heating a mixture of Tin(II) bis(2‐ethylhexanoate) [Sn(Oct)₂], hydroxyl functionalized Wang resin, and PDO in anhydrous toluene at 80 °C. The resultant polymer‐grafted Wang resin (Wang‐g‐PPDO) was characterized by fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), optical microscopy (OM), and field‐emission scanning electron microscopy (FE‐SEM). The FTIR spectra of Wang‐g‐PPDO show peak characteristic of PPDO at 2943 cm^?1 (? C? H stretch), at 1741 cm^?1 (? C?O stretch), and 1136 cm^?1 (C? O? C stretch) indicating the formation of ester linkage between PPDO and hydroxyl terminated Wang resin. The DSC thermogram show melting peak corresponding to PPDO polymer on Wang resin surface. Thermogravimetric investigation shows increase in PPDO content on the Wang resin surface in terms of percentage of weight loss with increase in reaction time. The OM and SEM photographs clearly show the formation of PPDO polymer on the Wang resin surface without altering the spherical nature of Wang resin bead. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1178–1184, 2008     

Synthesis and characterization of a new ethynyl‐linked alternating anthracene/fluorene copolymer for organic thin film transistor

A new p‐type conjugated copolymer, poly(9,10‐diethynylanthracene‐alt‐9,9‐didodecylfluorene) (PDADF), which is composed of ethynyl‐linked alternating anthracene/fluorene, is synthesized via a palladium(II)‐catalyzed Sonogashira coupling reaction with 9,10‐diethynylanthracene and 2,7‐diiodo‐9,9‐didodecyl‐fluorene. The obtained polymer is confirmed by FTIR, ¹H‐NMR, ¹³C‐NMR and elemental analysis. The PDADF had very good solubility in organic solvents such as chloroform and had a weight average molecular weight of 29,300 with a polydispersity index of 1.29. The PL maximum of the polymer was found at 533 and 568 nm for a solution and 608 nm for film, respectively. The highest occupied molecular orbital (HOMO) energy of the polymer is ?5.62 eV as measured via cyclic voltammetry (CV). A solution‐processed thin film transistor device showed a carrier mobility value of 6.0 × 10^?4 cm²/Vs with a threshold voltage of ?17 V and a capacitance (C_i) of 10 nF/cm². The out‐of‐plane and in‐plane GIXD pattern of spin‐coated polymer on SiO₂ dielectric surfaces showed an amorphous halo near 2θ = 20°. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1609–1616, 2009     

Arborescent polystyrene‐graft‐poly(tert‐butyl methacrylate) copolymers: Synthesis and enhanced polyelectrolyte effect in solution

A technique is described for the preparation of arborescent graft copolymers containing poly(tert‐butyl methacrylate) (PtBMA) segments. For this purpose, tert‐butyl methacrylate is first polymerized with 1,1‐diphenyl‐2‐methylpentyllithium in tetrahydrofuran. The graft copolymers are obtained by addition of a solution of a bromomethylated polystyrene substrate to the living PtBMA macroanion solution. Copolymers incorporating either short (M_w ≈ 5000) or long (M_w ≈ 30,000) PtBMA side chains were prepared by grafting onto linear, comb‐branched (G0), G1, and G2 bromomethylated arborescent polystyrenes. Branching functionalities ranging from 9 to 4500 and molecular weights ranging from 8.8 × 10⁴ to 6.3 × 10⁷ were obtained for the copolymers, while maintaining a low apparent polydispersity index (M_w/M_n ≈ 1.14–1.25). Arborescent polystyrene‐graft‐poly(methacrylic acid) (PMAA) copolymers were obtained by hydrolysis of the tert‐butyl methacrylate units. Dynamic light scattering measurements showed that the arborescent PMAA copolymers are more expanded than their linear PMAA analogues when neutralized with NaOH. This effect is attributed to the higher charge density in the branched arborescent copolymer structures. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2335–2346, 2008     

Poly[(2‐alkoxy‐5‐methyl‐1,3‐phenylene vinylene)‐alt‐(phenylene vinylene)] derivatives with different contents of cis‐ and trans‐olefins: The effect of the olefin bond geometry and conjugation length on luminescence

Poly[(2‐alkyloxy‐5‐methyl‐1,3‐phenylenevinylene)‐alt‐(1,3‐phenylenevinylene)]s ( 8 ) and poly[(2‐alkyloxy‐5‐methyl‐1,3‐phenylenevinylene)‐alt‐(1,4‐phenylenevinylene)]s ( 10 ) were synthesized by the Wittig reaction to provide materials containing 45–62% cis‐vinylene bonds. The optical characteristics of 8 and 10 were compared with those of their respective isomers, 3 and 4 , the cis‐vinylene contents of which were significantly lower (9–16%). Although a greater fraction of cis‐CH?CH linkages caused the absorption maximum (λ_max) of 8 and 10 to be slightly blueshifted (by ～3–6 nm) from that of 3 and 4 , the impact of the vinylene bond geometry appeared to be negligible on their fluorescence spectra. The fluorescence quantum efficiencies of 8 and 10 were estimated to be approximately 0.25 and 0.72, respectively. Both 8 (λ_max ≈ 445 or 462 nm) and 10 (λ_max ≈ 480 or 506 nm) were electroluminescent, showing effective color tuning by the controlled insertion of m‐phenylene moieties. The external electroluminescence quantum efficiencies were determined to be 4.26 × 10^?3% for 8 and 0.63% for 10 . The cis/trans‐vinylene bond ratio had a great impact on the electroluminescence device performance of 8 but a much smaller impact on the performance of 10 . © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 303–316, 2004     

New P‐type of poly(4‐methoxy‐triphenylamine)s derived by coupling reactions: Synthesis,electrochromic behaviors,and hole mobility

Methoxy‐substituted poly(triphenylamine)s, poly‐4‐methoxytriphenylamine ( PMOTPA ), and poly‐N,N‐bis(4‐methoxyphenyl)‐N′,N′‐diphenyl‐p‐phenylenediamine ( PMOPD ), were synthesized from the nickel‐catalyzed Yamamoto and oxidative coupling reaction with FeCl₃. All synthesized polymers could be well characterized by ¹H and ¹³C NMR spectroscopy. These polymers possess good solubility in common organic solvent, thermal stability with relatively high glass‐transition temperatures (T_gs) in the range of 152–273 °C, 10% weight‐loss temperature in excess of 480 °C, and char yield at 800 °C higher than 79% under a nitrogen atmosphere. They were amorphous and showed bluish green light (430–487 nm) fluorescence with quantum efficiency up to 45–62% in NMP solution. The hole‐transporting and electrochromic properties are examined by electrochemical and spectroelectrochemical methods. All polymers exhibited reversible oxidation redox peaks and E_onset around 0.44–0.69 V versus Ag/AgCl and electrochromic characteristics with a color change under various applied potentials. The series of PMOTPA and PMOPD also showed p‐type characteristics, and the estimated hole mobility of O ‐ PMOTPA and Y ‐ PMOPD were up to 1.5 × 10^?4 and 5.6 × 10^?5 cm² V^?1 s^?1, respectively. The FET results indicate that the molecular weight, annealing temperature, and polymer structure could crucially affect the charge transporting ability. This study suggests that triphenylamine‐containing conjugated polymer is a multifunctional material for various optoelectronic device applications. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4037–4050, 2009     

Naphthodithiophene‐Diketopyrrolopyrrole‐Based donor–Acceptor alternating π‐Conjugated polymers for Organic thin‐Film transistors

Novel naphtho[1,2‐b:5,6‐b′]dithiophene (NDT) and diketopyrrolopyrrole (DPP)‐containing donor‐acceptor conjugated polymers (PNDTDPPs) with different branched side chains were synthesized via Pd(0)‐catalyzed Stille coupling reaction. Octyldodecyl (OD) and dodecylhexadecyl (DH) groups were tethered to the DPP units as the side chains. The soluble fraction of PNDTDPP‐OD polymer in chloroform has much lower molecular weight than that of PNDTDPP‐DH polymer. PNDTDPP‐DH polymer bearing relatively longer DH side chains exhibited much better charge‐transport behavior than PNDTDPP‐OD polymer with shorter OD side chains. The thermally annealed PNDTDPP‐DH polymer thin films exhibited an outstanding charge carrier mobility of ～1.32 cm² V^?1 s^?1 (I_on/I_off ～ 10⁸) measured under ambient conditions, which is almost six times higher than that of thermally annealed PNDTDPP‐OD polymer thin films. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5280–5290     

Cationic photopolymerization of cis‐2,3‐tetramethylene‐1,4,6‐trioxaspiro[4,4]nonane

The spiro‐orthoester, cis‐2,3‐tetramethylene‐1,4,6‐trioxaspiro[4,4]nonane (cis‐TTN) ( I ), underwent rapid cationic photopolymerization when exposed to UV light using diphenyliodonium salts as a photoinitiator. The polymer, poly[(trans‐OCB)_x′‐(cis‐OCB)_x″‐(CHO)_y] thus formed consisted of poly(trans‐2‐oxycyclohexyl butanoate) (trans‐OCB)_x′ ( II ), poly(cis‐2‐oxycyclohexyl butanoate) (cis‐OCB)_x″ ( III ), and poly‐ (1,2‐cyclohexene oxide) (CHO)_y segments, and no expected pure poly(ether‐ester), that is, poly(2‐oxycyclohexyl butanoate), was isolated. The structure of the polymer was identified, and the mechanism of the reaction was deduced. The polymer thus formed exhibited expansion in volume during cationic photopolymerization when compared to that obtained by conventional cationic polymerization using a Lewis acid (e.g., BF₃OEt₂, CH₃OSO₂CF₃, or SnCl₄) as an initiator, which demonstrated volume shrinkage during polymerization. The volume expansion of the polymer during polymerization was due to (1) the lower content of the higher density (CHO)_y segment in the polymer chain and, more importantly, (2) the higher and optimal mole ratio of (trans‐OCB)_x′ and (cis‐OCB)_x″ segments that led the polymer in a more disordered, less dense, and higher volumetric state. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3680–3690, 2009     

Aggregation behavior of polystyrene‐b‐poly(ethylene/butylene)‐b‐polystyrene triblock copolymer in N‐methylpyrrolidone

Solution property of hydrogenated polystyrene‐b‐poly(ethylene/butylene)‐b‐polystyrene triblock copolymer (SEBS copolymer) was studied by using static light scattering and dynamic light scattering for cyclohexane and N‐methylpyrrolidone (NMP) solutions. From the values of dimensionless parameters ρ, defined as the ratio of radius of gyration 〈S²〉^1/2 to hydrodynamic radius R_H, and solubility parameters, SEBS copolymer proved to exist as single chain close to random coil in nonpolar cyclohexane, whereas aggregate into the core‐shell micelle consisting of poly(ethylene/butylene) (PEB) core surrounded by PS shell in polar NMP. The core‐shell micelle formed in NMP is composed of 65 polymer chains, having three times larger average chain density (d = 0.12 g cm^?3) than a single polymer chain (d = 0.04 g cm^?3) in cyclohexane. The comparison with the aggregation behaviors in other solvents demonstrated that the aggregate compactness of the copolymer depended largely on solvent polarity, resulting in formation of the highly dense PEB core (R_c = 4.5 nm) and the thick PS shell (ΔR = 22.9 nm) in high‐polar NMP. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 588–594, 2010