Effects of solvent,casting temperature,and guest/host stoichiometries on the properties of shape memory material based on partial α‐CD‐PEG inclusion complex

A series of supramolecular inclusion complex (IC) films were formed by threading α‐cyclodextrin (α‐CD) molecules over poly(ethylene glycol) (PEG), according to the designed ratio of α‐CD/PEG. Because of containing α‐CD‐PEG inclusion crystallites as physical crosslinks and uncovered PEG crystallites as “switch phase”, the resulting supramolecular α‐CD‐PEG partial ICs displayed a shape memory effect. The properties of the materials were investigated by ¹H‐NMR, X‐ray diffraction (XRD), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and swelling measurement. It was found that the casting temperature, solvent, and the ratio of α‐CD‐PEG inclusion/PEG had great influence on the formation and properties of α‐CD‐PEG partial ICs. The modes of complexes on different conditions were proposed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 951–957, 2010     

Transport properties of small molecules in zwitterionic polymers

Despite great interests in using zwitterionic polymers for membrane surface modification to enhance antifouling properties, there lacks fundamental understanding of the relationship between polymer structure and water/salt separation properties. In this study, two series of zwitterionic polymers were prepared from sulfobetaine methacrylate and 2‐methacryloyloxyethyl phosphorylcholine. Both are crosslinked by poly(ethylene glycol) diacrylate (PEGDA). These copolymers were thoroughly characterized in terms of sol‐gel fraction, density, glass transition temperature, contact angle, water and salt transport properties, and pure‐gas permeability. Interestingly, the zwitterionic polymers exhibit water sorption and permeability similar to noncharged poly(ethylene glycol)‐based materials. These zwitterionic polymers exhibit lower NaCl diffusivity and permeability and thus higher water/NaCl selectivity than the non‐charged PEG‐based materials at similar water volume fractions, demonstrating their promise for membrane surface modification for desalination and wastewater treatment. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1924–1934     

Crosslinking polymerization leading to interpenetrating polymer network formation. II. Polyaddition crosslinking reactions of poly(methyl methacrylate‐co‐2‐methacryloyloxyethyl isocyanate) with various diols

As part of our continuing studies concerned with the elucidation of the crosslinking polymerization mechanism leading to interpenetrating polymer network (IPN) formation, in which IPNs consist of both polymethacrylates and polyurethane (PU) networks, this article explores the polyaddition crosslinking reactions of multifunctional poly(methyl methacrylate‐co‐2‐methacryloyloxyethyl isocyanate) [poly(MMA‐co‐MOI)] [MMA/MOI = 90/10] with various diols leading to PU network formation. Thus, the equimolar polyaddition crosslinking reactions of poly(MMA‐co‐MOI) with ethylene glycol (EG), 1,6‐hexane diol, and 1,10‐decane diol (DD) were carried out in N‐methyl pyrrolidone at a 0.25 mol/L isocyanate group concentration at 80 °C. The second‐order rate constants decreased from EG to DD. The deviation of the actual gel point from the theoretical one was smaller from EG to DD. The intrinsic viscosity of resulting prepolymer demonstrated almost no variation with progressing polymerization for the EG system, whereas it gradually increased with conversion for the DD system. Close to the gel point conversion it increased rather drastically for both systems. The swelling ratio of resulting gel was higher from EG to DD. These are discussed mechanistically in terms of the significant occurrence of intramolecular cyclization and intramolecular crosslinking reactions leading to shrinkage of the molecular size. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3243–3248, 2003     

Lithium chloride as catalyst for the ring-opening polymerization of lactide in the presence of hydroxyl-containing compounds

Lithium chloride was found to be an effective and biocompatible catalyst for the ring-opening polymerization of lactide in the presence of hydroxyl-containing compounds. Ethylene glycol (EG) and methyl α-D -glucopyranoside (MGlc) were used as multifunctional initiators. The polymerization was carried out at 128°C in bulk with 1% (w/w) of LiCl. Polylactide (PLA) of different molecular weights was obtained with varied molar ratios of monomer/initiator ([M]₀/[I]₀). The LiCl-catalyzed ring-opening polymerization was applied to the synthesis of a number of amphiphilic PLA copolymers when poly(ethylene glycol) (PEG), hydroxyethyl cellulose (HEC), and hydroxypropyl cellulose (HPC) were used as macroinitiators. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3486–3491, 1999     

The effect of composition variables on precursor degradation and their consequence on Nb2O5 film properties prepared by the Pecchini Method

The calcination of Nb₂O₅ prepared by the Pecchini method was investigated using thermal analysis. The polymer precursor was prepared with different citric acid/ethylene glycol (CA/EG) and citric acid/niobium precursor (CA/Nb) molar ratios. The results suggest a strong influence of the CA/EG molar ratio, mainly on the polymerization degree. The CA/Nb ratio also modifies the degradation process of the precursor solution. The effect of the precursor compositional variation was also observed in the oxide structure, as well as in its electrochemical and electrochromic behavior. Films prepared using high CA/EG and a Nb salt precursor amount have the highest values of charge density and coloration efficiency. Moreover XRD data for this sample show a crystalline structure while the samples prepared with low CA/EG ratio are amorphous.     

Synthesis and characterization of poly(2,5‐furan dicarboxylate)s based on a variety of diols

Novel polyesters from renewable resources based on 2,5‐dicarboxylic acid and several diols were synthesized and characterized using different polycondensation techniques. The aliphatic diols were sufficiently volatile to allow the use of polytransesterifications, which gave high‐molecular weight semicrystalline materials with good thermal stability. In particular, the polyester based on ethylene glycol displayed properties comparable with those of its aromatic counterpart, poly(ethylene terephthalate), namely, the most important industrial polyester. The use of isosorbide gave rise to amorphous polymers with very stiff chains and hence a high glass transition temperature and an enhanced thermal stability. The interfacial polycondensation between the acid dichloride and hydroquinone produced a semicrystalline material with features similar to those of entirely aromatic polyesters, characterized essentially by the absence of melting and poor solubility, both associated with their remarkable chain rigidity. The replacement of hydroquinone with the corresponding benzylic diol was sufficient to provide a more tractable polyester. This study provided ample evidence in favor of the exploitation of furan monomers as renewable alternatives to fossil‐based aromatic homologs. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of poly(ethylene glycol) bottlebrush networks via ring-opening metathesis polymerization

Herein it is reported how the overlap concentration (C*) can be used to overcome crosslinking due to diol impurities in commercial poly(ethylene glycol) (PEG), allowing for the synthesize of bottlebrush polymers with good control over molecular weight. Additionally, PEG-based bottlebrush networks are synthesized via ring-opening metathesis polymerization, attaining high conversions with minimal sol fractions (<2%). The crystallinity and mechanical properties of these networks are then further altered by solvent swelling with phosphate buffer solution and 1-ethyl-3-methylimidazolium ethyl sulfate/dichloromethane cosolvents. The syntheses reported here highlight the potential of the bottlebrush network architecture for use in the rational design of new materials.     

聚己内酯－聚乙二醇嵌段共聚物Ⅱ．组成、结晶性同降解性间关系

采用ＤＳＣ法测定了新嵌段共聚物聚己内酯（ＰＣＬ）－聚乙二醇（ＰＥＧ）嵌段共聚物（ＰＣＥ）的结晶性，研究了共聚物的结晶性同组成及降解性的关系．结果表明随着共聚物中ＰＥＧ组分的含量和分子量增加，共聚物的结晶性下降，亲水性提高，降解速度加快．     

Construction of different supramolecular polymer systems by combining the host–guest and hydrogen‐bonding interactions

Poly(ethylene glycol) (PEG) can form either the inclusion complex with α‐cyclodextrins (α‐CDs) through host–guest interactions or the interpolymer complex with poly(acrylic acid) (PAA) through hydrogen‐bonding interaction. Mixing α‐CD, PEG, and PAA ternary components in an aqueous solution, the competition between host–guest and hydrogen‐bonding interactions occurs. Increasing feed ratio of α‐CD:EG:AA from 0:1:1 to 0.2:1:1 (molar ratio), various interesting supramolecular polymer systems, such as hydrogen‐bonding complex, dynamic polyrotaxane, crystalline inclusion complex, and thermoresponsive hydrogel, are successively obtained. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1114–1120, 2008     

聚己内酯－聚乙二醇嵌段共聚物Ⅱ．组成、结晶性同降解性间关系

采用ＤＣＳ法测定了新嵌段共聚物聚己内酯－聚乙二醇嵌段共聚物的结晶性，研究了共聚物的结晶性同组成及降解性的关系。结果表明随着共聚物中ＰＥＧ组分的含量和分子量增加，共聚物的结晶性下降，亲水性提高，降解速度加快。     

Structural Versatility in Slide‐Ring Gels: Influence of Co‐Threaded Cyclodextrin Spacers

We describe a one‐pot strategy for the fabrication of novel slide‐ring (SR) gels based on supramolecular polyrotaxane structures with cyclodextrin‐derived cross‐links and additional free cyclodextrin ring spacers co‐threaded onto the polymer backbones. Photoinitiated thiol‐yne click coupling leads to facile hydrogel fabrication from pseudo‐polyrotaxanes prepared in situ from β‐cyclodextrin derivatives and bifunctional polyethylene glycol (PEG). The obtained SR gels were characterized by NMR spectroscopy using a polyrotaxane model compound with the ratio of cyclodextrin sliding spacers to PEG backbone controlled by adjusting the feed ratio of the starting materials. This structural tuning leads to dramatic changes in the rheological properties, mechanical properties, and swelling behavior of the SR gels. In addition, the coupling of simple synthetic procedures with enhanced properties offers a versatile approach to novel elastomeric materials. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 55, 1156–1165     

New semi-interpenetrating network hydrogels: synthesis, characterization and properties

Amphiphilic hydrogels composed of aliphatic polyesters and poly(ethylene glycol) have potential applications in drug delivery, tissue engineering and other biomedical devices due to their advantageous biological properties, biocompatibility and biodegradability. However, they also exhibit some shortcomings in terms of their reactivity, swelling and mechanical properties. To address these limitations, new semi-interpenetrating network (semi-IPN) hydrogels based on poly(ethylene glycol)-co-poly(epsilon-caprolactone) (PEG-PCL) diacrylate macromer and hydroxypropyl guar gum (HPGG) were prepared by a low intensity ultraviolet (UV) light irradiation method, and characterized by FT-IR, DSC and WAXD analysis. Their properties were evaluated by investigating the swelling kinetics, dynamic mechanical rheology and the release behavior for bovine serum albumin (BSA). It was found that the introduction of the semi-IPN structure and HPGG decreased the crystallinity of PEG segments in the hydrogel, and improved the swelling and mechanical properties of the hydrogel, as well as lowered the release percentage of BSA from the hydrogel. Such hydrogel materials may have more advantages as a potentially interesting platform for the design of medical devices.The elastic modulus (G') and viscous modulus (G') as a function of frequency for various hydrogel samples.     

Preparation of LiTaO<Subscript>3</Subscript> nanoparticles by a sol–gel route

A sol–gel route was developed to prepare pure ultrafine LiTaO₃ powders using Ta₂O₅, Li₂CO₃, citric acid (CA) as chelating agent, ethylene glycol (EG) as esterification agent and polyethylene glycol (PEG) as dispersant. The effects of pH value and heat treatment temperature of powder precursor on the synthesis of LiTaO₃ powders were investigated. The phase content and morphology of the final product were evaluated by XRD, SEM and TEM. A transparent gel was produced when heating a mixed-solution of CA, EG, Li and Ta ions with a molar ratio of [CA]:[EG]:[Li]:[Ta] = 3.0:6.0:1.0:1.0 and 2‰ PEG additions with a pH value of 7 at water bath temperature of 80 °C. The results showed that single phase LiTaO₃ powders with average particle sizes of nanometers were produced after heat treatment of the powder precursor at 650, 700, 800, and 900 °C respectively for 2 h.     

Synthesis and characterization of spherical and hemispherical polyepoxide micrometer‐sized particles of narrow size distribution by a single‐step swelling of uniform polystyrene template microspheres with glycidyl methacrylate

Polystyrene template microspheres of narrow size distribution were prepared by dispersion polymerization of styrene in a mixture of ethanol and 2‐methoxy ethanol. Spherical and hemispherical polystyrene/poly(glycidyl methacrylate) microspheres of narrow size distribution were prepared by a single‐step swelling of the polystyrene template microspheres with the swelling solvent monomer glycidyl methacylate, followed by polymerization of the monomer within the swollen template microspheres at 73 °C. Uniform polystyrene/poly(glycidyl methacylate‐ethylene glycol dimethacrylate) polyepoxide composite microspheres were synthesized similarly, substituting glycidyl methacylate for glycidyl methacylate and ethylene glycol dimethacrylate. Uniform crosslinked poly(glycidyl methacylate‐ethylene glycol dimethacrylate) polyepoxide microspheres have been prepared by dissolution of the PS template polymer of the former composite microspheres. Particles with different properties, for example size, size distribution, shape, surface morphology, surface area, and so forth, were prepared by changing various parameters belonging to the swelling and/or polymerization steps, for example, volume of the swelling monomer/s and/or the swelling solvent dibutyl phthalate. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4612–4622, 2007     

Interaction between poly(ethylene glycol) and water as studied by differential scanning calorimetry

The interaction between poly(ethylene glycol) (PEG) and water was studied by differential scanning calorimetry (DSC). The DSC curves of PEG–water systems were classified into three groups according to the difference in molecular weight. The melting peaks of eutectic mixture appeared for PEG with molecular weight higher than 1000. The eutectic point temperature shifted to higher temperatures and the eutectic point composition shifted to lower concentrations of PEG with increasing molecular weight. The maximum hydration number per ethylene glycol (EG) unit was estimated as 1.6, 2.4, and 3.3 for samples with molecular weights 400, 1540, and 70,000, respectively. No thermal change was found in PEG1540‐water system for a narrow weight fraction range of 0.585–0.605 for overall measuring temperatures due to perfect supercooling. The glass transition temperature shifted to higher temperatures with increasing molecular weight of PEG. A modified Flory–Huggins equation was used to fit curves for experimental liquidus data in phase diagrams. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 496–506, 2001     

Solid polymer electrolytes III: Preparation,characterization, and ionic conductivity of new gelled polymer electrolytes based on segmented,perfluoropolyether‐modified polyurethane

New segmented polyurethanes with perfluoropolyether (PFPE) and poly(ethylene oxide) blocks were synthesized from a fluorinated macrodiol mixed with poly(ethylene glycol) (PEG) in different ratios as a soft segment, 2,4‐toluene diisocyanate as a hard segment, and ethylene glycol as a chain extender. Fourier transform infrared, NMR, and thermal analysis [differential scanning calorimetry and thermogravimetric analysis (TGA)] were used to characterize the structures of these copolymers. The copolymer films were immersed in a liquid electrolyte (1 M LiClO₄/propylene carbonate) to form gel‐type electrolytes. The ionic conductivities of these polymer electrolytes were investigated through changes in the copolymer composition and content of the liquid electrolyte. The relative molar ratio of PFPE and PEG in the copolymer played an important role in the conductivity and the capacity to retain the liquid electrolyte solution. The copolymer with a 50/50 PFPE/PEG ratio, having the lowest decomposition temperature shown by TGA, exhibited the highest ionic conductivity and lowest activation energy for ion transportation. The conductivities of these systems were about 10^?3 S cm^?1 at room temperature and 10^?2 S cm^?1 at 70 °C; the films immersed in the liquid electrolyte with an increase of 70 wt % were homogenous with good mechanical properties. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 486–495, 2002; DOI 10.1002/pola.10119     

Synthesis and characterization of block poly(ester‐ether‐urethane)s from bacterial poly(3‐hydroxybutyrate) oligomers

Telechelic hydroxylated poly(3‐hydroxybutyrate) (PHB‐diol) oligomers have been successfully synthesized in 90–95% yield from high molar mass PHB by tin‐catalyzed alcoholysis with different diols (mainly 1,4‐butanediol) in diglyme. The PHB‐diol oligomers structure was studied by nuclear magnetic resonance, Fourier transformed infrared spectroscopy MALDI‐ToF MS, and size exclusion chromatography, whereas their crystalline structures, thermal properties and thermal stability were analyzed by wide angle X‐ray scattering, DSC, and thermogravimetric analyses. The kinetic of the alcoholysis was studied and the influence of (i) the catalyst amount, (ii) the diol amount, (iii) the reaction temperature, and (iv) the diol chain length on the molar mass was discussed. The influence of the PHB‐diol molar mass on the thermal stability, the thermal properties and optical properties was investigated. Then, tin‐catalyzed poly(ester‐ether‐urethane)s (PEEU) of M_n = 15,000–20,000 g/mol were synthesized in 1,2‐dichloroethane from PHB‐diol oligomers (P_ester) with modified 4,4'‐MDI and different polyether‐diols (P_ether) (PEG‐2000, PEG‐4000, and PPG‐PEG‐PPG). The influence of the PHB‐diol chain length, the P_ether/P_ester ratio, the polyether segment nature and the PEG chain length on the thermal properties and crystalline structures of PEEUs was particularly discussed. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1949–1961     

Combining “click” chemistry and step‐growth polymerization for the generation of highly functionalized polyesters

Aliphatic polyesters bearing pendant alkyne groups were successfully prepared by step‐growth polymerization of different building blocks such as adipic acid and succinic acid in combination with an acetylene‐based diol, 2‐methyl‐2‐propargyl‐1,3‐propanediol, besides 1,4‐butanediol and ethylene glycol. It was demonstrated that the alkyne groups survive the high reaction temperatures (200 °C) in the presence of a radical inhibitor. The alkyne loading has been tuned by the ratio of the different monomers used, up to 25 mol % of alkyne groups. Subsequently, the alkyne groups have been reacted with azides by the copper‐catalyzed Huisgen 1,3‐dipolar cycloaddition reaction, a popular type of “click” chemistry. “Click” reactions have been performed quantitatively in the presence of benzyl azide and azide‐terminated poly(ethylene glycol), yielding brush copolymers in the latter case. Kinetic investigations about this click reaction have been performed by means of on‐line Fourier transform mid‐infrared spectroscopy, which was reported for the first time in the field of the click chemistry research. A whole range of functionalized polyesters, based on poly(ethylene succinate) and poly(butylene adipate), is available, the properties of which can be tailored by choosing the appropriate azide compound. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6552–6564, 2008     

Characterization of well‐defined poly(ethylene glycol) hydrogels prepared by thiol‐ene chemistry

Considering the large number of applications for hydrogels, a better understanding of the relation between molecular structure and mechanical properties for well‐defined hydrogel is essential. A new library has been compiled of poly(ethylene glycol) polymers (PEG) of different length end functionalized with diallyl, dithiol, and dimethacrylate, and crosslinked with complementary trifunctional crosslinkers. In this study, the hydrogels were initially analyzed by FT‐Raman and NMR to study the conversion ratio of the functional groups. The effects of solvent type, solid content concentration, curing time and length of the PEG chains on the final leaching, swelling and tensile properties of the hydrogels were studied. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

The fabrication of hollow magnetite microspheres with a nearly 100% morphological yield and their applications in lithium ion batteries

Hollow Fe_3O_4(H-Fe_3O_4) microspheres were fabricated through a facile one-step solvothermal synthesis,which was performed in an ethylene glycol(EG)–diethylene glycol(DEG) mixed solvent using polyethylene glycol(PEG) as the stabilizer. The addition of DEG increased the viscosity of the system,which caused the Fe_3O_4 primary crystal to aggregate slower and the morphological yield to approach nearly 100%. The as-prepared hollow Fe_3O_4 microspheres show promise for application in lithium ion battery anodes and showed a reversible specific capacity of 453.3 mAh g~(-1) after 50 cycles at 100 mA g~(-1).