Sliding threshold of spike‐rate dependent plasticity of a semiconducting polymer/electrolyte cell

Spike‐rate dependent plasticity, one of the conventional learning protocols in neuroscience, has been achieved in semiconducting polymer/electrolyte cells. The frequency threshold θ_m of spike‐rate dependent plasticity is sliding in requirement of stability. In this work, various prior signal inputs are applied to poly[2‐methoxy‐5‐(2‐ethylhexyloxy)?1,4‐phenylenevinylene]/polyethylene oxide ‐Nd³⁺ cells to explore their effects on θ_m.The study find that a prior inhibitory input, i.e., a weak stimulation, moves θ_m in the low frequency direction, while a prior excitatory input, i.e., an intensive stimulation, moves θ_m in the high frequency direction. Our results demonstrate the adaptivity of ionic kinetics in macromolecules systems for signal handling and learning. We suggest that a sliding threshold is due to the variable active ionic domains depending on stimulation strength and history. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2412–2417     

Preparation of lithium fast ionic conductor by sol-gel-hydrothermal method

The solid fast ionic conductor was synthesized by the sol-gel-hydrothermal method. The influences of the dispersion reagent, the alkalinity and the calcination temperature on the surface morphology of nanopowders, and the electric conductivity were discussed. When PEG 12000 was used as the dispersion reagent, the alkalinity was 1.0% and the calcination temperature was 550°C; the electric conductivity at ambience temperature of the inorganic nanopowder of lithium fast ionic conductor synthesized was 2.59 × 10⁻³ S·cm⁻¹. __________ Translated from Journal of National University of Defense Technology, 2005, 27(2) (in Chinese)     

固体电解质Li9-nxMn+xN2Cl3(M=Na、Mg、Al)的合成及表征

高温固相反应合成了固体电解质Li_(9-nx)M~(n )_xN_2Cl_3(M=Na、Mg、Al)。利用粉末 X射线衍射测定样品结构。测定了离子电导率 ,分解电压和电子电导。得出掺杂可以提高快离子导体材料 Li_9N_2Cl_3的电导率。并讨论了掺杂阳离子的半径和价态与替代离子的关系和影响。使用 x=0.05mol的二价镁离子替代 Li_9N_2Cl_3中的 Li＋离子可以很大程度的提高其电导率。     

Large‐scale aligned fiber mats prepared by salt‐induced pulse electrospinning

In this article, a new large‐scale aligned fiber mats formation method called salt‐induced pulse electrospinning was developed. By electrospinning salted solution in a humid environment, traditional continuous electrospinning changed into pulse electrospinning and aligned fibers were thus formed. The possible mechanisms for the occurrence of salt‐induced pulse electrospinning and the formation of fiber alignment were studied. The continuous electrospinning changing into the pulse electrospinning was due to the change of viscosity and conductivity of salted polymer solution in a wet electrospinning condition. Fishing net‐shaped whipping region of the electrospinning jet during pulse electrospinning process was considered as the key factor for the formation of fiber alignment. The mechanical properties of the aligned fiber mat increased significantly compared with that of the random fiber mat. This aligned fiber preparation method only requires a very low rotating drum speed as the receiver and can produce large‐scale aligned fiber mats for many applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Synthesis and characterization of Ti and N binary‐doped ɑ‐C films deposited by pulse cathode arc with ionic source assistant

Using ionic source assistant, Ti and N co‐doped amorphous C (α‐C:N:Ti) thin films were prepared by pulse cathode arc technique. Microstructure, composition, elemental distribution, morphology, and mechanical properties of α‐C:N:Ti films were investigated in dependence of nitrogen source, pulse frequency, and target current by Raman spectroscopy, X‐ray diffraction, scanning electron microscopy, X‐ray photoelectron spectroscopy, atomic force microscopy, nanoindentation, and surface profilometer. The results show the presence of titanium carbide and nitride in a‐C:N:Ti films. The α‐C:N⁺:Ti film (6 Hz, 60 A) shows the smaller size and the higher disordering degree of Csp² clusters. The α‐C:N⁺:Ti films present smoother surface and smaller particle size than for α‐C:N₂:Ti films. N ions facilitate the formation of N‐sp³C bonds in the α‐C:N⁺:Ti films, and α‐C:N⁺:Ti (10 Hz, 80 A) film possesses the more graphite‐like N bonds. Higher hardness and lower residual stress present in the α‐C:N₂:Ti (10 Hz, 80 A) film.     

固体电解质Li9-nxMn+xN2Cl3(M=Na、Mg、Al)的合成及表征

高温固相反应合成了固体电解质Ｌｉ９－ｎｘＭ＾ｎ＋ｘＮ２Ｃｌ３（Ｍ＝Ｎａ、Ｍｇ、Ａｌ）。利用粉末Ｘ射线衍射测定样品结构,测定了离子电导率,分解电压和电子电导。得出掺杂可以提高快离子快离子导体材料Ｌｉ９Ｎ２Ｃｌ３中的Ｌｉ＾＋离子可以很大程度的提高其电导率。     

Adjusting the chromatographic properties of poly(ionic liquid)‐modified stationary phases by substitution on the imidazolium cation

Poly(ionic liquid)‐modified stationary phases can have multiple interactions with solutes. However, in most stationary phases, separation selectivity is adjusted by changing the poly(ionic liquid) anions. In this work, two poly(ionic liquid)‐modified silica stationary phases were prepared by introducing the cyano or tetrazolyl group on the pendant imidazolium cation on the polymer chains. Various analytes were selected to investigate their mechanism of retention in the stationary phases using different mobile phases. Two poly(ionic liquid)‐modified stationary phases can provide various interactions toward solutes. Compared to the cyano‐functionalized poly(ionic liquid) stationary phase, the tetrazolyl‐functionalized poly(ionic liquid) stationary phase provides additional cation‐exchange and π‐π interactions, resulting in different separation selectivity toward analytes. Finally, applicability of the developed stationary phases was demonstrated by the efficient separation of nonsteroidal anti‐inflammatory drugs.     

Extraction of Cupric Ions with Ionic Liquids Containing Polypyridine‐type Small Molecules or Peripherally Pyridine‐modified Dendrimers

The hydrophobic ionic liquid N‐butyl‐N‐methylpyrrolidinium bis((trifluoromethyl)sulfonyl)amide (BMP‐TFSA IL), which contains a series of flexible ionophores of polypyridine‐type small molecules or two rigid ionophores of peripherally pyridine‐modified PAMAM dendrimers, was used to extract cupric ions from aqueous solutions. The polypyridine‐type ionophores show good selectivity toward cupric ions at pH 2. The selectivity is affected by the spacing between the two amino groups. However, the pyridine‐modified dendrimers showed poor selectivity, although their extraction efficiency still depended on the pH of the aqueous solution. The ionic liquids that contained small molecular ionophores and their dendrimer analogs were reused after acid washing or electrochemical reduction. During acid washing, the nitrogen atoms of the ionophores were protonated to release the cupric ions into the aqueous phase, and the copper atoms were deposited onto the electrode surface during the electrochemical reduction accompanied by the regeneration of the ionophores.     

Shape transformation of poly(butadiene)‐b‐poly(ethyleneoxide) plus DTAB compound micelles in aqueous solutions

The micellar shape of Poly(butadiene)‐b‐poly(ethyleneoxide) (PB‐PEO) plus Dodecyltrimethylammoniumbromide (DTAB) compound micelles was investigated by light scattering, small‐angle X‐ray scattering and small‐angle neutron scattering in dependence of the molar ratio between block copolymer and surfactant. The given block copolymer forms cylindrical micelles in binary aqueous solution, which transform to spherical aggregates upon the addition of a sufficiently high amount of DTAB. It is interesting to note that the micellar shape seems to be a bistable feature, in the sense that it depends not only on the molar ratio of BCP and DTAB but also in a predictable manner on the preparation procedure of the solution.     

Interpretation of the polyelectrolyte and antipolyelectrolyte effects of poly(N‐vinylimidazole‐co‐sodium styrenesulfonate) hydrogels

Hydrogels of N‐vinylimidazole (VI) and sodium styrenesulfonate (SSS) were synthesized in aqueous solution by radical crosslinking copolymerization with N,N′‐methylene‐bis(acrylamide) as crosslinker. Swelling in several saline solutions was measured for hydrogel samples synthesized with different comonomer concentrations (C_T = 10, 25, or 40%) and with SSS mole fractions covering a broad range (f_SSS = 0–0.7), while the crosslinker ratio was 2 wt % in all cases. The degree of swelling in aqueous solution with a specific ionic strength (μ), plotted versus the SSS composition of the feed, shows a minimum for any set of samples synthesized with a fixed C_T. The dependence of swelling on μ shows both polyelectrolyte (f_SSS beyond the minimum) and antipolyelectrolyte behaviors (in the low f_SSS limit). It was found that the nonGaussian factor of the crosslinking density and the polymer‐solvent interaction parameter increase with f_SSS for any C_T. Moreover, in the low f_SSS limit, the osmotic swelling pressure is governed not only by the ionic contribution, but also by the polymer‐solvent mixing and, the concentration of mobile counterions inside the gel is not proportional to the net fixed charge but to the addition of cationic and anionic side groups, what discards the formation of ionic pairs. The antipolyelectrolyte effect is interpreted as due to the increasing protonation of VI as μ goes up. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1683–1693, 2007     

Computer‐Assisted Design of Imidazolate‐Based Ionic Liquids for Improving Sulfur Dioxide Capture,Carbon Dioxide Capture,and Sulfur Dioxide/Carbon Dioxide Selectivity

A new strategy involving the computer‐assisted design of substituted imidazolate‐based ionic liquids (ILs) through tuning the absorption enthalpy as well as the basicity of the ILs to improve SO₂ capture, CO₂ capture, and SO₂/CO₂ selectivity was explored. The best substituted imidazolate‐based ILs as absorbents for different applications were first predicted. During absorption, high SO₂ capacities up to ≈5.3 and 2.4 mol mol_IL⁻¹ could be achieved by ILs with the methylimidazolate anions under 1.0 and 0.1 bar (1 bar=0.1 MPa), respectively, through tuning multiple N ⋅⋅⋅ S interactions between SO₂ and the N atoms in the imidazolate anion with different substituents. In addition, CO₂ capture by the imidazolate‐based ILs could also be easily tuned through changing the substituents of the ILs, and 4‐bromoimidazolate IL showed a high CO₂ capacity but a low absorption enthalpy. Furthermore, a high selectivity for SO₂/CO₂ could be reached by IL with 4,5‐dicyanoimidazolate anion owing to its high SO₂ capacity but low CO₂ capacity. The results put forward in this work are in good agreement with the predictions. Quantum‐chemical calculations and FTIR and NMR spectroscopy analysis methods were used to discuss the SO₂ and CO₂ absorption mechanisms.     

Exploiting the versatility of vacuum‐assisted headspace solid‐phase microextraction in combination with the selectivity of ionic liquid‐based GC stationary phases to discriminate Boswellia spp. resins through their volatile and semivolatile fractions

The frankincense resins, secreted from Boswellia species, are an uncommon example of a natural raw material where every class of terpenoids is present in similar proportions. Diterpenoids (serratol, incensole, and incensole acetate) are used to discriminate samples from different species and origins. Headspace solid‐phase microextraction has been used for frankincense analysis, although it requires long sampling time for medium‐ to low‐volatility markers; headspace solid‐phase microextraction under vacuum can overcome this limit. Gas chromatography is used for analysis but the separation of incensole and serratol needs polar stationary phases. In this study, we develop a method to discriminate frankincenses based on vacuum‐assisted headspace solid‐phase microextraction combined with fast gas chromatography‐mass spectrometry with ionic liquid–based stationary phases. The optimized conditions for solid samples were: air evacuation below 0°C, 15 min of incubation time, and 15 min of extraction time. Losses of volatiles due to vial air‐evacuation in the presence of the sample were minimized by sample amount above 100 mg and low sample temperature. Fast gas chromatography provides the baseline separation of all markers in 20 min. By applying vacuum sampling and fast gas chromatography, the total analysis was reduced to 50 min compared to 120 min (60 min sampling plus 60 min analysis) as previously reported. The method was successfully applied to commercial frankincense samples.     

Characterisation of mixed lithium dodecyl sulphate/lithium perfluorooctanesulphonate pseudo‐stationary phases in MEKC

Lipophilicity and methylene selectivity of mixed pseudo‐stationary phases (PSPs) (containing lithium dodecyl sulphate (LDS) and lithium perfluorooctanesulphonate (LiPFOS) in different molar ratios) applied in MEKC have been investigated. Micellar proportion (t_prop,mic, a quantity expressing that how much time is spent by the analyte in the micellar phase related to its whole migration time), CLOGP₅₀ value (showing the value of hydrophobicity of a molecule spending exactly 50% of its migration time in the PSP) and methylene selectivity have been determined for different LDS/LiPFOS mixed phases. Values of the above‐mentioned parameters have been determined for analytes with different chemical structures (alkylbenzene and alkylphenone homologous series, alcohols). Good linear correlation was obtained between either the micellar proportion, CLOGP₅₀, or methylene selectivity and the phase composition for the mixed phases. Lipophilicity and methylene selectivity of the mixed LDS/LiPFOS PSPs can be calculated and can continuously be changed by mixing the two single phases (LDS and LiPFOS) in the appropriate (and calculable) portion.     

On the High‐temperature Crystal Structure of Sr/Mg‐doped Lanthanum Gallate. Evidence for the First Perovskite‐type Structure with R3¯m Symmetry

The high temperature structure above 700 °C of the oxygen superionic conductor La_0.9Sr_0.1Ga_0.8Mg_0.2O_2.85 has been analyzed by means of a combined neutron and high resolution synchrotron powder study. The splitting of reflections and the absence of any superstructure reflections leads to the conclusion that the correct space group is R3¯m. This is the first example of this space group appearing within the subgroup family of the ideal parent perovskite structure with Pm3¯m symmetry.     

Metal‐Nitrogen‐doped Porous Carbons Derived from Metal‐Containing Ionic Liquids for Oxygen Reduction Reaction

This study describes a self‐doping and additive‐free strategy for the synthesis of metal‐nitrogen‐doped porous carbon materials (CMs) via carbonizing well‐tailored precursors, metal‐containing ionic liquids (M‐ILs). The organic skeleton in M‐ILs serves as both carbon and nitrogen sources, while metal ions acts as porogen and metallic dopants. A high nitrogen content, appropriate content of metallic species and hierarchical porosity synergistically endow the resultant CMs (MIBA‐M‐T) as effective electrocatalysts for the oxygen reduction reaction (ORR). MIBA‐Fe‐900 with a high specific surface area of 1567 m² g^?1 exhibits an activity similar to that of Pt/C catalyst, a higher tolerance to methanol than Pt/C, and long‐term durability. This work supplies a simple and convenient route for the preparation of metal‐containing carbon electrocatalysts.     

Gas sorption and characterization of poly(ether‐b‐amide) segmented block copolymers

The solubilities of He, H₂, N₂, O₂, CO₂, CH₄, C₂H₆, C₃H₈, and n‐C₄H₁₀ were determined at 35°C and pressures up to 27 atmospheres in a systematic series of phase separated polyether–polyamide segmented block copolymers containing either poly(ethylene oxide) [PEO] or poly(tetramethylene oxide) [PTMEO] as the rubbery polyether phase and nylon 6 [PA6] or nylon 12 [PA12] as the hard polyamide phase. Sorption isotherms are linear for the least soluble gases (He, H₂, N₂, O₂, and CH₄), convex to the pressure axis for more soluble penetrants (CO₂, C₃H₈, and n‐C₄H₁₀) and slightly concave to the pressure axis for ethane. These polymers exhibit high CO₂/N₂ and CO₂/H₂ solubility selectivity. This property appears to derive mainly from high carbon dioxide solubility, which is ascribed to the strong affinity of the polar ether linkages for CO₂. As the amount of the polyether phase in the copolymers increases, gas solubility increases. The solubility of all gases is higher in polymers with less polar constituents, PTMEO and PA12, than in polymers with more polar PEO and PA6 units. CO₂/N₂ and CO₂/H₂ solubility selectivity, however, are higher in polymers with higher concentrations of polar repeat units. The sorption data are complemented with physical characterization (differential scanning calorimetry, elemental analysis, and wide angle X‐ray diffraction) of the various block copolymers. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2463–2475, 1999     

Protection‐Group‐Free Synthesis of Sequence‐Defined Macromolecules via Precision λ‐Orthogonal Photochemistry

An advanced light‐induced avenue to monodisperse sequence‐defined linear macromolecules via a unique photochemical protocol is presented that does not require any protection‐group chemistry. Starting from a symmetrical core unit, precision macromolecules with molecular weights up to 6257.10 g mol^?1 are obtained via a two‐monomer system: a monomer unit carrying a pyrene functionalized visible light responsive tetrazole and a photo‐caged UV responsive diene, enabling an iterative approach for chain growth; and a monomer unit equipped with a carboxylic acid and a fumarate. Both light‐induced chain growth reactions are carried out in a λ‐orthogonal fashion, exciting the respective photosensitive group selectively and thus avoiding protecting chemistry. Characterization of each sequence‐defined chain (size‐exclusion chromatography (SEC), high‐resolution electrospray ionization mass spectrometry (ESI‐MS), and NMR spectroscopy), confirms the precision nature of the macromolecules.     

Preparation and utilization of poly(methacryloylsilatrane) as a salt‐dissociation enhancer in PEO‐based polymer electrolytes

Polymers containing silatrane units were prepared by the free radical polymerization of methacryloylsilatrane (MPS), and their conductivities were evaluated. We confirmed that MPS can be polymerized without excessive decomposition of the silatrane units by the radical polymerization initiated by azobisisobutyronitrile. The chemical structure of the polymerized MPS (pMPS) was characterized by Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy, gel permeation chromatography, and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectroscopy. The pMPS formed a homogeneous complex with lithium trifluoromethyl sulfonate (LiOTf), although the obtained pMPS/LiOTf complex did not show conductivity. The negligible conductivity was caused by the high glass transition temperature (T_g) of the pMPS matrix, which exceeded 70°C. The pMPS was subsequently utilized as a salt‐dissociation enhancer for the poly(ethylene oxide)‐based polymer electrolyte. MPS was copolymerized with poly[methacryloyl oligo(ethylene oxide)] (pMEO) by free radical polymerization. When the pMEO incorporated a small amount of MPS units (i.e. lower than 15 mol%), the elevation in T_g was not observed, and the conductivity markedly improved. Among the series of copolymers and when compared with pristine pMEO, the copolymer containing 6.3% of MPS units had the maximum conductivity (3.1 × 10^?4 S cm^?1 at 80°C). The Vogel–Fulcher–Tammann fitting parameters showed that the conductivity was improved by the increase in the number of carrier ions. The enhancement in salt dissociation was presumably due to the homogeneous incorporation of polar MPS units. However, when the MPS unit content exceeded 15 mol%, the conductivity was lowered because of the increase in T_g. Copyright © 2013 John Wiley & Sons, Ltd.     

Engineering Fast Ion Conduction and Selective Cation Channels for a High‐Rate and High‐Voltage Hybrid Aqueous Battery

The rechargeable aqueous metal‐ion battery (RAMB) has attracted considerable attention due to its safety, low costs, and environmental friendliness. Yet the poor‐performance electrode materials lead to a low feasibility of practical application. A hybrid aqueous battery (HAB) built from electrode materials with selective cation channels could increase the electrode applicability and thus enlarge the application of RAMB. Herein, we construct a high‐voltage K–Na HAB based on K₂FeFe(CN)₆ cathode and carbon‐coated NaTi₂(PO₄)₃ (NTP/C) anode. Due to the unique cation selectivity of both materials and ultrafast ion conduction of NTP/C, the hybrid battery delivers a high capacity of 160 mAh g^?1 at a 0.5 C rate. Considerable capacity retention of 94.3 % is also obtained after 1000 cycles at even 60 C rate. Meanwhile, high energy density of 69.6 Wh kg^?1 based on the total mass of active electrode materials is obtained, which is comparable and even superior to that of the lead acid, Ni/Cd, and Ni/MH batteries.