Effect of PS‐b‐PCL block copolymer on reaction‐induced phase separation in epoxy/PEI blend

PS‐b‐PCL block copolymer is used to study its influence on the phase evolution of epoxy resin/polyetherimides (PEI) blends cured with methyl tetrahydrophthalic anhydride. The effect of PS‐b‐PCL on the reaction‐induced phase separation of the thermosetting/thermoplastic blends is studied via optical microscopy, scanning electron microscope, and time‐resolved light scattering. The results show that secondary phase separation and typical phase inverted morphologies are obtained in the epoxy/PEI blends with addition of PS‐b‐PCL. It can be attributed to the preferential location of the PS‐b‐PCL in the epoxy‐rich phase, which enhances the viscoelastic effect of epoxy/PEI system and leads to a dynamic asymmetry system between PEI and epoxy. The PS‐b‐PCL block copolymer plays a critical role on the balance of the diffusion and geometrical growth of epoxy molecules. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1395–1402     

Nanostructured thermoset epoxy resin templated by an amphiphilic poly(ethylene oxide)‐block‐poly(dimethylsiloxane) diblock copolymer

An amphiphilic poly(ethylene oxide)‐block‐poly(dimethylsiloxane) (PEO–PDMS) diblock copolymer was used to template a bisphenol A type epoxy resin (ER); nanostructured thermoset blends of ER and PEO–PDMS were prepared with 4,4′‐methylenedianiline (MDA) as the curing agent. The phase behavior, crystallization, hydrogen‐bonding interactions, and nanoscale structures were investigated with differential scanning calorimetry, Fourier transform infrared spectroscopy, transmission electron microscopy, and small‐angle X‐ray scattering. The uncured ER was miscible with the poly(ethylene oxide) block of PEO–PDMS, and the uncured blends were not macroscopically phase‐separated. Macroscopic phase separation took place in the MDA‐cured ER/PEO–PDMS blends containing 60–80 wt % PEO–PDMS diblock copolymer. However, the composition‐dependent nanostructures were formed in the cured blends with 10–50 wt % PEO–PDMS, which did not show macroscopic phase separation. The poly(dimethylsiloxane) microdomains with sizes of 10–20 nm were dispersed in a continuous ER‐rich phase; the average distance between the neighboring microdomains was in the range of 20–50 nm. The miscibility between the cured ER and the poly(ethylene oxide) block of PEO–PDMS was ascribed to the favorable hydrogen‐bonding interaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3042–3052, 2006     

Controlled epoxidation of poly(styrene‐b‐isoprene‐b‐styrene) block copolymer for the development of nanostructured epoxy thermosets

To be used as templates for nanostructured thermosets, a commercial poly(styrene‐b‐isoprene‐b‐styrene) (SIS) block copolymer (BCP) was epoxidized by three different epoxidation procedures. An exhaustive analysis of methodologies using metal catalyzed/hydrogen peroxide, dimethyldioxirane (DMDO), and meta‐chloroperbenzoic acid (m‐CPBA) was performed to obtain reactive BCPs. The DMDO approach was the best strategy to obtain highly epoxidized SIS BCP (85 mol %) without formation of side products. Careful control in BCP epoxidation by metal catalyzed/hydrogen peroxide and m‐CPBA approaches led to a maximum epoxidation degree (ED) of approximately 60 mol % without the formation of side products. The ED by metal catalyzed/hydrogen peroxide strategy could be further increased to 69 mol %, but a significant amount of crosslinking, ring opening, and polymer chain scission reactions were detected by spectroscopic and chromatographic techniques. The miscibility of epoxidized BCPs with diglycidyl ether of bisphenol‐A epoxy system before and after curing was analyzed to develop nanostructured epoxy thermosets. For ED higher than 69 mol %, BCPs were miscible, while those with lower ED presented macrophase separation. Highly epoxidized BCPs obtained by the DMDO methodology were successfully used to obtain ordered nanodomains inside the epoxy matrix, as determined by atomic force microscopy. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of poly(di[methylamine]ethyl methacrylate)‐b‐poly(cyclohexyl methacrylate)‐b‐poly(di[methylamine]ethyl methacrylate) amphiphilic triblock copolymers by ATRP: Condensed‐phase and solution properties

The synthesis of amphiphilic triblock copolymers, poly(di[methylamine]ethyl methacrylate)‐b‐poly(cyclohexyl methacrylate)‐b‐poly(di[methylamine]ethyl methacrylate) PDMAE‐b‐PCH‐b‐PDMAE, has been performed by atom transfer radical polymerisation. Those have been obtained in a well‐controlled manner in terms of molecular weight and polydispersity index. The triblock copolymer characterisation has been made in condensed state and in solution. The existence of microphase separation has been confirmed by differential scanning calorimetry. However, the domains of both inner and outer blocks seem not to be ordered for one another from small‐angle X‐ray scattering (SAXS) measurements using synchrotron radiation. The micelle formation in dilute methanol solutions has been confirmed for all triblock copolymers by dynamic light scattering analyses. The size of these micelles has been demonstrated to be dependent on the molecular weight. Similar observations have been made in concentrate methanol solutions by using SAXS experiments, pointed also out that an increment of the intermicelle interactions is produced as the concentration increases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 85–92, 2008     

PEG‐b‐PtBA‐b‐PHEMA well‐defined amphiphilic triblock copolymer: Synthesis,self‐assembly,and application in drug delivery

A series of well‐defined amphiphilic triblock copolymers, poly(ethylene glycol)‐b‐poly(tert‐butyl acrylate)‐b‐poly(2‐hydroxyethyl methacrylate) (PEG‐b‐PtBA‐b‐PHEMA), were synthesized via successive atom transfer radical polymerization (ATRP). ATRP of tBA was first initiated by PEG‐Br macroinitiator using CuBr/N,N,N′,N″,N′″‐pentamethyldiethylenetriamine as catalytic system to give PEG‐b‐PtBA diblock copolymer. This copolymer was then used as macroinitiator to initiate ATRP of HEMA, which afforded the target triblock copolymer, PEG‐b‐PtBA‐b‐PHEMA. The critical micelle concentrations of obtained amphiphilic triblock copolymers were determined by fluorescence spectroscopy using N‐phenyl‐1‐naphthylamine as probe. The morphology and size of formed aggregates were investigated by transmission electron microscopy and dynamic light scattering, respectively. Finally, an acid‐sensitive PEG‐b‐PtBA‐b‐P(HEMA‐CAD) prodrug via cis‐aconityl linkage between doxorubicin and hydroxyls of triblock copolymers with a high drug loading content up to 38%, was prepared to preliminarily explore the application of triblock copolymer in drug delivery. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of fluorine‐containing PAA‐b‐PTPFCBPMA amphiphilic block copolymer

A series of perfluorocyclobutyl (PFCB) aryl ether‐based amphiphilic diblock copolymers containing hydrophilic poly(acrylic acid) (PAA) and fluorophilic poly(p‐(2‐(p‐tolyloxy)perfluorocyclobutoxy)phenyl methacrylate) segments were synthesized via successive atom transfer radical polymerization (ATRP). 2‐MBP‐initiated and CuBr/N,N,N′,N′,N″‐pentamethyldiethylenetriamine‐catalyzed ATRP homopolymerization of the PFCB‐containing methacrylate monomer, p‐(2‐(p‐tolyloxy)perfluorocyclobutoxy)phenyl methacrylate, can be performed in a controlled mode as confirmed by the fact that the number‐average molecular weights (M_n) increased linearly with the conversions of the monomer while the polydispersity indices kept below 1.38. The block copolymers with narrow molecular weight distributions (M_w/M_n ≤ 1.36) were synthesized by ATRP using Br‐end‐functionalized poly(tert‐butyl acrylate) (PtBA) as macroinitiator followed by the acidolysis of hydrophobic PtBA block into hydrophilic PAA segment. The critical micelle concentrations of the amphiphilic diblock copolymers in different surroundings were determined by fluorescence spectroscopy using N‐phenyl‐1‐naphthylamine as probe. The morphology and size of the micelles were investigated by transmission electron microscopy and dynamic laser light scattering, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Regulation of Micellar Morphology of PCL‐b‐PEO Block Copolymers by Crystallization Temperature

The effect of crystallization temperature on the micellar morphology of PCL‐b‐PEO block copolymers in water has been studied. It is found that the micellar morphology of PCL_nPEO₄₄ and PCL_nPEO₁₁₃ changes with crystallization temperature in different ways because of two competitive factors: perfection of the PCL crystals in the core and deformation of the soluble PEO block. For PCL_nPEO₄₄, perfection of the PCL crystals dominates the micellar morphology and lamellar micelles are formed at a higher crystallization temperature. For PCL_nPEO₁₁₃ the micellar morphology is mainly determined by the tethering density and spherical micelles or cylindrical micelles with a larger length/diameter ratio are formed at a higher crystallization temperature because of the larger tethering density.

     

Investigation by combined solid‐state NMR and SAXS methods of the morphology and domain size in polystyrene‐b‐polyethylene oxide‐b‐polystyrene triblock copolymers

The microphase structure of a series of polystyrene‐b‐polyethylene oxide‐b‐polystyrene (SEOS) triblock copolymers with different compositions and molecular weights has been studied by solid‐state NMR, DSC, wide and small angle X‐ray scattering (WAXS and SAXS). WAXS and DSC measurements were used to detect the presence of crystalline domains of polyethylene‐oxide (PEO) blocks at room temperature as a function of the copolymer chemical composition. Furthermore, DSC experiments allowed the determination of the melting temperatures of the crystalline part of the PEO blocks. SAXS measurements, performed above and below the melting temperature of the PEO blocks, revealed the formation of periodic structures, but the absence or the weakness of high order reflections peaks did not allow a clear assessment of the morphological structure of the copolymers. This information was inferred by combining the results obtained by SAXS and ¹H NMR spin diffusion experiments, which also provided an estimation of the size of the dispersed phases of the nanostructured copolymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 55–64, 2010     

Solid‐supported amphiphilic triblock copolymer membranes grafted from gold surface

Gold‐supported amphiphilic triblock copolymer brushes composed of two hydrophilic poly(2‐hydroxyethyl methacrylate) (PHEMA) blocks and a hydrophobic poly(n‐butyl methacrylate) (PBMA) middle part were synthesized using a surface‐initiated ATRP. Attenuated total reflectance Fourier transform infrared spectroscopy, polarization modulation infrared reflection absorption spectroscopy (PM‐IRRAS), ellipsometry, contact angle measurements, and atomic force microscopy were used for the characterization of PHEMA‐co‐PBMA‐co‐PHEMA brushes. The PM‐IRRAS analysis revealed an increase of the chain tilt toward the gold surface during growth of the individual blocks. We suggest that the orientation of the amphiphilic polymer brushes is influenced by both the chain length and the interchain interactions. Additionally, a detachment of the polymer membranes from the solid support and subsequent gel permeation chromatography analyses allowed us to establish their compositions. We applied block‐selective solvents (water and hexane) as well as a good solvent for the whole polymer chain (ethanol) to study the morphology and solvent responsive behavior of the amphiphilic brushes. The presented results could serve as a good starting point for the fabrication of functional solid‐supported membranes for biosensing applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1–13, 2009     

Phase behavior,crystallization, and nanostructures in thermoset blends of epoxy resin and amphiphilic star‐shaped block copolymers

This article reports thermoset blends of bisphenol A‐type epoxy resin (ER) and two amphiphilic four‐arm star‐shaped diblock copolymers based on hydrophilic poly(ethylene oxide) (PEO) and hydrophobic poly(propylene oxide) (PPO). 4,4′‐Methylenedianiline (MDA) was used as a curing agent. The first star‐shaped diblock copolymer with 70 wt % ethylene oxide (EO), denoted as (PPO‐PEO)₄, consists of four PPO‐PEO diblock arms with PPO blocks attached on an ethylenediamine core; the second one with 40 wt % EO, denoted as (PEO‐PPO)₄, contains four PEO‐PPO diblock arms with PEO blocks attached on an ethylenediamine core. The phase behavior, crystallization, and nanoscale structures were investigated by differential scanning calorimetry, transmission electron microscopy, and small‐angle X‐ray scattering. It was found that the MDA‐cured ER/(PPO‐PEO)₄ blends are not macroscopically phase‐separated over the entire blend composition range. There exist, however, two microphases in the ER/(PPO‐PEO)₄ blends. The PPO blocks form a separated microphase, whereas the ER and the PEO blocks, which are miscible, form another microphase. The ER/(PPO‐PEO)₄ blends show composition‐dependent nanostructures on the order of 10?30 nm. The 80/20 ER/(PPO‐PEO)₄ blend displays spherical PPO micelles uniformly dispersed in a continuous ER‐rich matrix. The 60/40 ER/(PPO‐PEO)₄ blend displays a combined morphology of worm‐like micelles and spherical micelles with characteristic of a bicontinuous microphase structure. Macroscopic phase separation took place in the MDA‐cured ER/(PEO‐PPO)₄ blends. The MDA‐cured ER/(PEO‐PPO)₄ blends with (PEO‐PPO)₄ content up to 50 wt % exhibit phase‐separated structures on the order of 0.5–1 μm. This can be considered to be due to the different EO content and block sequence of the (PEO‐PPO)₄ copolymer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 975–985, 2006     

Aggregation behavior of polystyrene‐b‐poly(ethylene/butylene)‐b‐polystyrene triblock copolymer in N‐methylpyrrolidone

Solution property of hydrogenated polystyrene‐b‐poly(ethylene/butylene)‐b‐polystyrene triblock copolymer (SEBS copolymer) was studied by using static light scattering and dynamic light scattering for cyclohexane and N‐methylpyrrolidone (NMP) solutions. From the values of dimensionless parameters ρ, defined as the ratio of radius of gyration 〈S²〉^1/2 to hydrodynamic radius R_H, and solubility parameters, SEBS copolymer proved to exist as single chain close to random coil in nonpolar cyclohexane, whereas aggregate into the core‐shell micelle consisting of poly(ethylene/butylene) (PEB) core surrounded by PS shell in polar NMP. The core‐shell micelle formed in NMP is composed of 65 polymer chains, having three times larger average chain density (d = 0.12 g cm^?3) than a single polymer chain (d = 0.04 g cm^?3) in cyclohexane. The comparison with the aggregation behaviors in other solvents demonstrated that the aggregate compactness of the copolymer depended largely on solvent polarity, resulting in formation of the highly dense PEB core (R_c = 4.5 nm) and the thick PS shell (ΔR = 22.9 nm) in high‐polar NMP. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 588–594, 2010     

Thermogelling behaviors of poly(caprolactone‐b‐ethylene glycol‐b‐caprolactone) triblock copolymer in the presence of hyaluronic acid

In this article, we studied the effect of hyaluronic acid (HA) on thermogelation of poly(caprolactone‐b‐ethylene glycol‐b‐caprolactone) (PCL‐PEG‐PCL) aqueous solution designed as an injectable system for prevention of postsurgical tissue adhesion. The PCL‐PEG‐PCL triblock copolymers were simply synthesized by ring‐opening polymerization of ε‐caprolactone (CL) in the presence of PEG as a polymeric initiator. The synthesized copolymers were confirmed by proton nuclear magnetic resonance (¹H‐NMR) spectroscopy. Possible interactions between HA and PCL‐PEG‐PCL triblock copolymers in the blend were evaluated by Fourier‐transform infrared spectroscopy (FTIR). The effect of HA on the micellization of PCL‐PEG‐PCL aqueous solution was investigated by dye solubilization method and electrophoretic lighting scattering (ELS) spectrophotometer. Also, the thermogelling behaviors of the PCL‐PEG‐PCL triblock copolymers in the presence of HA and their mechanism were investigated by test tube inverting method, ¹³C‐NMR, ¹H‐NMR, Advanced Rheometic Expansion System (ARES), and differential scanning calorimetry (DSC). The PCL‐PEG‐PCL/HA blend aqueous solutions undergo the sol‐gel‐sol transition in response to an increase in temperature (10–60 °C) and the gelation of the PCL‐PEG‐PCL was rather accelerated by HA. Presumably, this accelerated gelation seems to arise from the attractive interactions between them and the effect of chain confinement in the micelle corona region. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3629–3637, 2008     

Synthesis and dielectric properties of novel liquid crystalline triblock copolymers with cyanobiphenyl moieties and poly(n‐butyl acrylate) segments

In this work, self‐assembly method was used to improve the dielectric constant of triblock copolymers. A series of ABA triblock copolymers with a defined length of poly(n‐butyl acrylate) (PBA, B block) segment and different lengths of liquid crystalline (LC) poly[11‐(4‐cyano‐4′‐biphenoxy)undecyl methacrylate] (P11CBMA, A block) segments were synthesized by using the atom transfer radical polymerization method. The well‐defined triblock copolymers P11CBMA_m‐b‐PBA_n‐b‐P11CBMA_m possess three different B/A ratios (n = 50, m = 17, 43, 53). Due to the supramolecular cooperative motion effect, the copolymers can form worm‐like microstructure (W_LC = 52.8%), cylinder‐like nanostructure with P11CBMA phase embedded in PBA matrix (W_LC = 73.9%), and wide stripe structure with LC domains distributed unevenly in a continuous PBA matrix (W_LC = 77.7%) after annealed at 160°C (above T_i) under N₂ for 24 h, respectively. In order to study the influence of microphase separated morphology of triblock copolymer on the dielectric properties, solvent annealing was also used to develop various nanostructures. After thermal or solvent annealing, the dielectric constants of block copolymers increased dramatically while their loss factors remained the same. For different block copolymers, the dielectric constants increased with the increase of the LC block length. For diverse treatments, dielectric permittivities of samples varied widely with different nanostructures. The results show that the dielectric constants of block copolymers could be tuned by the block ratios and the self‐assembled microstructures. These findings will inspire researchers using self‐assembly method to design and develop novel flexible materials with high dielectric permittivity. Copyright © 2014 John Wiley & Sons, Ltd.     

Nanostructured organic–inorganic hybrid films prepared by the sol–gel method from self‐assemblies of PS‐b‐paptes‐b‐PS triblock copolymers

ABA‐based triblock copolymers of styrene as block ends and gelable 3‐acryloxypropyltriethoxysilane (APTES) as the middle block were successfully prepared through nitroxide‐mediated polymerization (NMP). The copolymers were bulk self‐assembled into films and the degree of phase separation between the two blocks was evaluated by differential scanning calorimetry (DSC). Their morphology was examined through small angle X‐ray scattering (SAXS) and transmission electron microscopy (TEM), whereas the mechanical properties of the corresponding cross‐linked self‐assembled nanostructures were characterized by dynamic mechanical analysis (DMA). Acidic treatment of the triblock copolymers favored the hydrolysis and condensation reactions of the APTES‐rich nanophase, and induced a mechanical reinforcement evidenced by the increase of storage modulus values and the shift of the glass transition temperature to higher temperatures due to confinement effects. In addition, the lamellar structure of the hybrid films was retained after the removal of the organic part by calcination. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Structure and properties of PBO–PEO diblock copolymer modified epoxy

Amphiphilic poly(n‐butylene oxide)‐b‐poly(ethylene oxide) (PBO–PEO) diblock copolymers of various compositions were synthesized and studied as modifiers for epoxy resins. In blends of PBO–PEO, epoxy resin, and curing agent, the copolymers formed well‐defined microstructures that persisted upon curing of the epoxy. The resulting morphologies were vesicles, worm‐like micelles, and spherical micelles (in order of increasing size of PEO block), as well as transitional morphologies. Addition of 5% by weight of these block copolymers improved the fracture toughness of the epoxy by as much as 19 times with relatively small reduction in the elastic modulus. The highest level of toughness was measured in a system containing branched worm‐like micelles. Close examination of the fracture surfaces of these compositions suggests that although all the dispersed morphologies played a similar role to inclusions in particle‐toughened thermosets, crack deflection toughening contributed to the significantly higher levels of toughness in the worm‐like micelle systems. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Chem 43: 1950–1965, 2005     

Synthesis of well‐defined amphiphilic polymethylene‐b‐poly(ε‐caprolactone)‐b‐poly(acrylic acid) triblock copolymer via a combination of polyhomologation,ring‐opening polymerization,and atom transfer radical polymerization

Well‐defined amphiphilic polymethylene‐b‐poly(ε‐caprolactone)‐b‐poly(acrylic acid) (PM‐b‐PCL‐b‐PAA) triblock copolymers were synthesized via a combination of polyhomologation, ring‐opening polymerization (ROP), and atom transfer radical polymerization (ATRP). First, hydroxyl‐terminated polymethylenes (PM‐OH; M_n = 1100 g mol^?1; M_w/M_n = 1.09) were produced by polyhomologation followed by oxidation. Then, the PM‐b‐PCL (M_n = 10,000 g mol^?1; M_w/M_n = 1.27) diblock copolymers were synthesized via ROP of ε‐caprolactone using PM‐OH as macroinitiator and stannous octanoate (Sn(Oct)₂) as a catalyst. Subsequently, the macroinitiator transformed from PM‐b‐PCL in high conversion initiated ATRPs of tert‐butyl acrylate (^tBA) to construct PM‐b‐PCL‐b‐P^tBA triblock copolymers (M_n = 11,000–14,000 g mol^?1; M_w/M_n = 1.24–1.26). Finally, the PM‐b‐PCL‐b‐PAA triblock copolymers were obtained via the hydrolysis of the P^tBA segment in PM‐b‐PCL‐b‐P^tBA triblock copolymers. The chain structures of all the polymers were characterized by gel permeation chromatography, proton nuclear magnetic resonance, and Fourier transform infrared spectroscopy. Porous films of such triblock copolymers were fabricated by static breath‐figure method and observed by scanning electron microscope. The aggregates of PM‐b‐PCL‐b‐PAA triblock copolymer were studied by transmission electron microscope. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Fourier transform infrared/attenuated total reflectance analysis of water diffusion in poly[styrene‐b‐isobutylene‐ b‐styrene] block copolymer membranes

A Fourier transform infrared/attenuated total reflectance technique was used to study the diffusion of water through poly(styrene‐b‐isobutylene‐b‐styrene) block copolymers (BCPs), as well as sulfonated (H⁺) and Na⁺‐sulfonated ionomer versions. Diffusion data were collected and interpreted for these membranes versus polystyrene block composition, degree of sulfonation, Na⁺ ion content in the ionomers, and the effect of initially dry versus prehydrated conditions. An “early time” diffusion coefficient, D, decreased with increasing percent polystyrene for a series of unmodified BCPs. D decreased with increasing degree of sulfonation, and with increasing ion content for the Na⁺‐exchanged samples and this was interpreted in terms of diffusion limitations caused by a strong tendency for ion hydration. The method also yielded information relating to the time evolution of water structure from the standpoint of degree of intermolecular hydrogen bonding. Membrane prehydration causes profound increases in D for both the unmodified BCP and sulfonated samples, as in plasticization. The simultaneous acquisition of information relating to interactions between water molecules and interactions of water molecules with functional groups on the host polymer matrix offers more information than conventional diffusion measurement techniques that simply count transported molecules. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 764–776, 2005     

Novel perfluorocyclobutyl aryl ether‐based well‐defined amphiphilic block copolymer

A series of fluorine‐containing amphiphilic diblock copolymers comprising hydrophobic poly(p‐(2‐(p‐tolyloxy)perfluorocyclobutoxy)phenyl methacrylate) (PTPFCBPMA) and hydrophilic poly(2‐(diethylamino)ethyl methacrylate) (PDEAEMA) segments were synthesized via successive reversible addition fragmentation chain transfer (RAFT) polymerizations. RAFT homopolymerization of p‐(2‐(p‐tolyloxy)perfluorocyclobutoxy)phenyl methacrylate was first initiated by 2,2′‐azobisisobutyronitrile using cumyl dithiobenzoate as chain transfer agent, and the results show that the procedure was conducted in a controlled way as confirmed by the fact that the number‐average molecular weights increased linearly with the conversions of the monomer while the polydispersity indices kept below 1.30. Dithiobenzoate‐capped PTPFCHPMA homopolymer was then used as macro‐RAFT agent to mediate RAFT polymerization of 2‐(diethylamino)ethyl methacrylate, which afforded PTPFCBPMA‐b‐PDEAEMA amphiphilic diblock copolymers with different block lengths and narrow molecular weight distributions (M_w/M_n ≤ 1.28). The critical micelle concentrations of the obtained amphiphilic diblock copolymers were determined by fluorescence spectroscopy technique using N‐phenyl‐1‐naphthylamine as probe. The morphology and size of the formed micelles were investigated by transmission electron microscopy and dynamic light scattering, respectively. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Biocompatible and pH‐responsive triblock copolymer mPEG‐b‐PCL‐b‐PDMAEMA: Synthesis,self‐assembly,and application

A series of well‐defined amphiphilic triblock copolymers [polyethylene glycol monomethyl ether]‐block‐poly(ε‐caprolactone)‐block‐poly[2‐(dimethylamino)ethyl methacrylate] (mPEG‐b‐PCL‐b‐PDMAEMA or abbreviated as mPEG‐b‐PCL‐b‐PDMA) were prepared by a combination of ring‐opening polymerization and atom transfer radical polymerization. The chemical structures and compositions of these copolymers have been characterized by Fourier transform infrared spectroscopy, ¹H NMR, and thermogravimetric analysis. The molecular weights of the triblock copolymers were obtained by calculating from ¹H NMR spectra and gel permeation chromatography measurements. Subsequently, the self‐assembly behavior of these copolymers was investigated by fluorescence probe method and transmission electron microscopy, which indicated that these amphiphilic triblock copolymers possess distinct pH‐dependent critical aggregation concentrations and can self‐assemble into micelles or vesicles in PBS buffer solution, depending on the length of PDMA in the copolymer. Agarose gel retardation assays demonstrated that these cationic nanoparticles can effectively condense plasmid DNA. Cell toxicity tests indicated that these triblock copolymers displayed lower cytotoxicity than that of branched polyethylenimine with molecular weight of 25 kDa. In addition, in vitro release of Naproxen from these nanoparticles in pH buffer solutions was conducted, demonstrating that higher PCL content would result in the higher drug loading content and lower release rate. These biodegradable and biocompatible cationic copolymers have potential applications in drug and gene delivery. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1079–1091, 2010