Semi‐interpenetrating polymer networks composed of poly(N‐isopropyl acrylamide) and polyacrylamide hydrogels

Three series of semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropyl acrylamide) (PNIPA) and 1 wt % nonionic or ionic (cationic and anionic) linear polyacrylamide (PAAm), were synthesized to improve the mechanical properties of PNIPA gels. The effect of the incorporation of linear polymers into responsive networks on the temperature‐induced transition, swelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25:1 to 100:1) of the monomer (N‐isopropyl acrylamide) to the crosslinker (methylenebisacrylamide). The hydrogels were characterized by the determination of the equilibrium degree of swelling at 25 °C, the compression modulus, and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. The introduction of cationic and anionic linear hydrophilic PAAm into PNIPA networks increased the rate of swelling, whereas the presence of nonionic PAAm diminished it. Transition temperatures were significantly affected by both the crosslinking density and the presence of linear PAAm in the hydrogel networks. Although anionic PAAm had the greatest influence on increasing the transition temperature, the presence of nonionic PAAm caused the highest dimensional change. Semi‐interpenetrating polymer networks reinforced with cationic and nonionic PAAm exhibited higher tensile strengths and elongations at break than PNIPA hydrogels, whereas the presence of anionic PAAm caused a reduction in the mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3987–3999, 2004     

High water content clay–nanocomposite hydrogels incorporating guanidinium‐pendant methacrylamide: Tuning of mechanical and swelling properties by supramolecular approach

Novel clay–polymer composite hydrogels with high water content (up to 98 wt %) are developed, in which mechanical properties are reinforced by the formation of multiple ion‐pairs between the polymer chains and clay nanosheets (CNS). When a small amount of guanidinium‐pendant methacrylamide (0.1–0.2 wt %) is copolymerized with a neutral monomer (0.5–2.0 wt %) in an aqueous dispersion of CNS (1.0–3.0 wt %), a self‐standing hydrogel with satisfactory mechanical toughness and elasticity results, despite its high water content (95–98 wt %). The mechanical properties and swelling behaviors of the hydrogels can be tuned by the amount of the guanidinium‐pendant acrylamide. A systematic study indicates that the ion pairs, formed between the guanidinium groups in the polymer chains and the oxyanions on the surfaces of the CNS, serve as crosslinking points in the three‐dimensional network developed in these hydrogels. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 839–847     

Double‐crosslinked reversible redox‐responsive hydrogels based on disulfide–thiol interchange

We present novel redox‐responsive hydrogels based on poly(N‐isopropylacrylamide) or poly(acrylamide), consisting of a reversible disulfide crosslinking agent N,N′‐bis(acryloyl)cystamine and a permanent crosslinking agent N,N′‐methylenebisacrylamide for microfluidic applications. The mechanism of swelling/deswelling behavior starts with the cleavage and reformation of disulfide bonds, leading to a change of crosslinking density and crosslinking points. Raman and ultraviolet‐visible spectroscopy confirm that conversion efficiency of thiol–disulfide interchange up to 99%. Rheological analysis reveals that the E modulus of hydrogel is dependent on the crosslinking density and can be repeatedly manipulated between high‐ and low‐stiffness states over at least 5 cycles without significant decrease. Kinetic studies showed that the mechanical strength of the gels changes as the redox reaction proceeds. This process is much faster than the autonomous diffusion in the hydrogel. Moreover, cooperative diffusion coefficient (D_coop) indicates that the swelling process of the hydrogel is affected by the reduction reaction. Finally, this reversibly switchable redox behavior of bulky hydrogel could be proven in microstructured hydrogel dots through short‐term photopatterning process. These hydrogel dots on glass substrates also showed the desired short response time on cyclic swelling and shrinking processes known from downsized hydrogel shapes. Such stimuli‐responsive hydrogels with redox‐sensitive crosslinkers open a new pathway in exchanging analytes for sensing and separating in microfluidics applications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2590–2601     

Zr(IV)‐Crosslinked Polyacrylamide/Polyanionic Cellulose Composite Hydrogels with High Strength and Unique Acid Resistance

Recently, metal coordination has been widely utilized to fabricate high‐performance hydrogels, but conventional metal‐based hydrogels face some drawbacks, such as staining or acid lability. In the present study, a novel kind of colorless Zr(IV)‐crosslinked polyacrylamide/polyanionic cellulose (PAM/PAC) composite hydrogel with unique acid resistance was constructed via acrylamide polymerization in a PAC solution, followed by posttreatment in a zirconium oxychloride (ZrOCl₂) solution. The prepared gels were characterized in terms of Fourier transform infrared spectroscopy, scanning electron microscopy, and tensile and compressive mechanics, as well as acid resistance. Inside the gels, the synergistic action of hydrogen bonding and Zr(IV) coordination is responsible for their improved mechanical properties and good energy dissipation ability. One hydrogel with nearly 90 wt % of water content can sustain approximately 5 MPa of compression stress at 90% strain without damage. Both microscopic network structures and macroscopic mechanics demonstrate facile adjustability via changing the PAC dosages in polymerization and/or ZrOCl₂ concentrations in posttreatment. Moreover, the gels present unexpected acid resistance due to the strong Zr(IV) coordination with PAC, demonstrating their potential application as hydrogel electrolytes in supercapacitors. The current work provides a new approach to fabricate metal coordination‐based high strength, colorless hydrogels with acid resistance. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 981–991     

Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

Ru(II)(tpy)2‐functionalized hydrogels: Synthesis,reversible responsiveness,and coupling with the belousov‐zhabotinsky reaction

This work aims at developing an approach to Ru(II)(Tpy)₂‐functionalized hydrogels and exploring the coupling of the hydrogels with the Belousov‐Zhabotinsky (BZ) reaction. Based on free radical polymerization, two synthetic routes are developed. The first one is the direct gelation by copolymerization of acrylamide as hydrophilic component and Ru(II)(Tpy)₂ as the functional group. The second one is carried out through a combined approach. A terpyridine‐containing hydrogel is first prepared and then post‐functionalized by coordination between Ru(III)(Tpy)Cl₃ and terpyridine groups in the hydrogel network. Utilizing the synthetic hydrogels, the reversible redox responsiveness, the coupling with the BZ reaction, the occurrence and the self‐oscillating properties of the BZ reaction in the hydrogel networks are studied. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2214–2222     

Swelling behavior of poly{N‐[3‐(dimethylaminopropyl)] methacrylamide‐co‐acrylamide} hydrogels in aqueous solutions of surfactants

Temperature sensitive poly{N‐[3‐(dimethylaminopropyl)]methacrylamide‐co‐acrylamide} [P(DMAPMA‐co‐AAm)] hydrogels were prepared by the free‐radical crosslinking copolymerization of corresponding monomers in water with N,N‐methylenebisacrylamide as the crosslinker, ammonium persulfate as the initiator, and N,N,N′,N′‐tetramethylethylenediamine as the activator. The swelling equilibrium of the P(DMAPMA‐co‐AAm) hydrogels was investigated as a function of temperature in aqueous solutions of the anionic surfactant sodium dodecyl sulfate and the cationic surfactant dodecyltrimethylammonium bromide. In pure water, regardless of the amount of N,N‐methylenebisacrylamide, the P(DMAPMA‐co‐AAm) hydrogels showed a discontinuous phase transition between 30 and 36 °C. However, the transition temperature changed from discontinuous to continuous with the addition of surfactants; this was ascribed to the conversion of nonionic P(DMAPMA‐co‐AAm) hydrogels into polyelectrolyte hydrogels due to the binding of surfactants through hydrophobic interactions. Additionally, the concentrations of free sodium dodecyl sulfate and dodecyltrimethylammonium bromide ions were measured at different temperatures by conductometry, and it was found that the electric conductivity of the P(DMAPMA‐co‐AAm)–surfactant systems depended strongly on the swelling ratio; most notably, it changed drastically near the phase‐transition temperature of the P(DMAPMA‐co‐AAm) hydrogel. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1645–1652, 2006     

Organic–inorganic hybrid hydrogels involving poly(N‐isopropylacrylamide) and polyhedral oligomeric silsesquioxane: Preparation and rapid thermoresponsive properties

3‐Acryloxypropylhepta(3,3,3‐trifluoropropyl) polyhedral oligomeric silsesquioxane (POSS) was synthesized and used as a modifier to improve the thermal response rates of poly(N‐isopropylacrylamide) (PNIPAM) hydrogel. The radical copolymerization among N‐isopropylacrylamide (NIPAM), the POSS macromer and N,N′‐methylenebisacrylamide was performed to prepare the POSS‐containing PNIPAM cross‐linked networks. Differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) showed that the POSS‐containing PNIPAM networks displayed the enhanced glass transition temperatures (T_g's) and improved thermal stability when compared with plain PNIPAM network. The POSS‐containing PNIPAM hydrogels exhibited temperature‐responsive behavior as the plain PNIPAM hydrogels. It is noted that with the moderate contents of POSS, the POSS‐containing PNIPAM hydrogels displayed much faster response rates in terms of swelling, deswelling, and re‐swelling experiments than plain PNIPAM hydrogel. The improved thermoresponsive properties of hydrogels have been interpreted on the basis of the formation of the specific microphase‐separated morphology in the hydrogels, that is, the POSS structural units in the hybrid hydrogels were self‐assembled into the highly hydrophobic nanodomains, which behave as the microporogens and promote the contact of PNIPAM chains and water. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 504–516, 2009     

Structural rearrangement and stiffening of hydrophobically modified supramolecular hydrogels during thermal annealing

Dynamic crosslinks formed by thermoreversible associations provide an energy dissipation mechanism to toughen hydrogels. However, the details of the organization of these crosslinks impact the hydrogel properties through constraints on the network chain conformation. The physical crosslinks generated by hydrophobic association of the 2‐(N‐ethylperfluorooctane‐sulfonamido)ethyl methacrylate (FOSM) groups in a random copolymer of N,N‐dimethylacrylamide (DMA) and FOSM provide a simple system to investigate how the hydrogel structure (as determined from small angle neutron scattering impacts the mechanical properties of the hydrogel. The initial hydration of the copolymer at 25 °C leads to a kinetically trapped structure with large‐scale heterogeneities. Heating the hydrogel at 60 °C, which is above the glass transition temperature for the FOSM domains, allows the hydrogel structure to rearrange to reduce the density of network defects and the structural heterogeneities. That effectively increases the crosslink density of the network, which stiffens the hydrogel and decreases the swelling at equilibrium at 25 °C. The processing history determines how the hydrophobes aggregate to form the physically crosslinked network, whose structure defines the mechanical properties of these hydrogels. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1036–1044     

Network structure and swelling–shrinking behaviors of pH‐sensitive poly(acrylamide‐co‐itaconic acid) hydrogels

pH‐sensitive poly(acrylamide‐co‐itaconic acid) [P(AAm/IA)] hydrogels were prepared by radiation induced copolymerization of acrylamide (AAm) and itaconic acid (IA) at various ratios. Swelling and shrinking behaviors of these hydrogels were found greatly dependent on the composition of the hydrogel and pH of the buffer solution. The basic structural parameters of the P(AAm/IA) networks such as the molecular weight between crosslinks (M _c) and polymer–solvent interaction parameter (χ) were also determined using the modified Flory‐Rehner equations. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2586–2594, 2004     

Novel salep‐based chelating hydrogel for heavy metal removal from aqueous solutions

A novel optimized chelating hydrogel was synthesized via graft copolymerization of acrylamide and 2‐hydroxyethyl methacrylate (as two‐dentate chelating co‐monomer) onto salep (a multicomponent polysaccharide obtained from dried tubers of certain natural terrestrial orchids) using N,N′‐methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator. Reaction parameters (N,N′‐methylenebisacrylamide and ammonium persulfate amounts as well as acrylamide/2‐hydroxyethyl methacrylate weight ratio) affecting the water absorption of the chelating hydrogel were optimized using a systematic method to achieve a hydrogel with high swelling capacity as possible. Heavy metal ion adsorption capacity of the optimized hydrogel for metal ions [Cu (II), Pb (II), Cd (II), and Cr (III)] were investigated in aqueous media containing different concentrations of these ions (5–50 ppm). The results showed that the hydrogel have great potential for heavy metal removal from aqueous solutions. The hydrogel formation was confirmed by Fourier transform infrared spectroscopy, and surface morphology study of the hydrogel was performed by scanning electron microscope. Copyright © 2016 John Wiley & Sons, Ltd.     

pH/temperature double responsive behaviors and mechanical strength of laponite‐crosslinked poly(DEA‐co‐DMAEMA) nanocomposite hydrogels

A nanocomposite (NC) hydrogel crosslinked by inorganic Laponite XLG was successfully synthesized via in situ free radical polymerization of monomers N,N‐diethylacrylamide and (2‐dimethylamino) ethyl methacrylate (DMAEMA). Polymerization was carried out at room temperature due to the accelerating effect of DMAEMA. The as‐prepared hydrogels displayed controlled transformation in optical transmittance and volume in response to small diversification of environmental factors, such as temperature and pH. The compressive strength of swollen D_6:1G₆ hydrogels was as high as 2219 kPa while compressive strain was 95%. Cyclic compression measurement exhibited good elastic properties of NC hydrogels. This work provides a facile method for fabricating stimuli‐responsive hydrogels with superior mechanical property. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 876–884     

Thermoresponsive super water absorbent hydrogels prepared by frontal polymerization of N‐isopropyl acrylamide and 3‐sulfopropyl acrylate potassium salt

Super water absorbent polymer hydrogels were synthesized by frontal polymerization. These materials were obtained by copolymerizing N‐isopropyl acrylamide (NIPAAm) and 3‐sulfopropyl acrylate potassium salt (SPAK) in the presence of N,N′‐methylene‐bis‐acrylamide as a crosslinker. It was found that their swelling behavior in water can be easily tuned by using either the appropriate monomer ratio or the amount of the crosslinker used. Namely, the swelling ratio was found to range from about 1000% for the NIPAAm homopolymer in the presence of 5.0 mol % of crosslinker, up to 35,000% for the sample containing 87.5 mol % of SPAK and 1.0 mol % of crosslinker. The affinity toward water was also confirmed by contact angle analysis. Moreover, the obtained hydrogels exhibit a thermoresponsive behavior, with a lower critical solution temperature of about 28–30 °C. This value is close to that of poly(NIPAAm) but with a swelling capability that dramatically increases as the amount of SPAK increases. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

pH‐responsive ionic poly(N,N‐diethylaminoethyl methacrylate‐co‐N‐vinyl‐2‐pyrrolidone) hydrogels: Synthesis and swelling properties

A series of an ionic hydrogels composed of N,N‐diethylaminoethyl methacrylamide (DEAEMA), N‐vinyl‐2‐pyrrolidone (VP), and itaconic acid were synthesized by free‐radical cross‐linking copolymerization in water–ethanol mixture by using N,N‐methylenebis(acrylamide) as the cross‐linker, ammonium persulfate as the initiator, and N,N,N′,N′‐tetramethylenediamine as the activator. The swelling behaviors of these hydrogels were analyzed in buffer solutions at various pH. It was observed that the swelling behavior of cross‐linked ionic poly(N,N‐diethylaminoethyl methacrylamide‐co‐N‐vinyl‐2‐pyrrolidone) [P(DEAEMA/VP)] hydrogels at different pH agreed with the modified Flory–Rehner equation based on the affine network model and the ideal Donnan theory. The swelling process in buffer solutions at various pH was found to be Fickian‐type diffusion. The pH‐reversibility and on–off switching properties of the P(DEAEMA/VP) hydrogels may be considered as good candidate to design novel drug‐delivery system. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2819–2828, 2005     

Synthesis,characterization, and drug release behaviors of a novel thermo‐sensitive poly(N‐acryloylglycinates)

In this study, a novel thermo‐sensitive poly(N‐acryloylglycinates) was prepared in order to get a potential drug release carrier. The corresponding monomers and the polymers were characterized with Fourier‐transform infrared (FTIR) and ¹H NMR. The thermo‐sensitivity of the poly(N‐acryloylglycinates) was evaluated by measuring their lower critical solution temperatures (LCST) in water, inorganic salt solution, and different pH solutions. The results indicated that poly(N‐acryloylglycine methyl ester) (NAGME) and poly(N‐acryloylglycine ethyl ester) (NAGEE) exhibit a reversible thermo‐sensibility in their aqueous solutions at 61.5 and 12.5°C, respectively. However, no thermo‐sensitive behavior of poly(N‐acryloylglycine propyl ester) (NAGPE) was found due to its over hydrophobicity. The swelling studies on hydrogels were carried out at different temperatures, in different pH, and inorganic salt solutions. The hydrogels showed a remarkable phase transition at about 35°C with changing temperature. The release rate of caffeine from the thermo‐sensitive hydrogel was apparently decreased as the crosslinker content increased and temperature decreased. Seventy five percent caffeine from the polymeric hydrogel with 5% NMBA (N, N‐methylenebis(acrylamide)) was released at room temperature within 240 min, whereas 95.4% caffeine diffused into the medium at 37°C. Copyright © 2009 John Wiley & Sons, Ltd.     

Self‐assembled graphene oxide–gelatin nanocomposite hydrogels: Characterization,formation mechanisms,and pH‐sensitive drug release behavior

Novel physically crosslinked graphene oxide (GO)‐gelatin nanocomposite hydrogels were obtained by self‐assembly. The hydrogels with various ratios of GO to gelatin were prepared, and characterized by X‐ray diffraction, Fourier transform infrared spectroscopy, Raman spectroscopy, and scanning electron microscopy. The static and dynamic rheological properties of the hydrogels were investigated, along with the underlying hydrogel formation mechanisms. The storage modulus of the hydrogels (containing 98–98.5 wt % water) reached 114.5 kPa, owing to the relatively strong physical bonding (i.e., hydrogen bonding and electrostatic forces) between GO and gelatin. Drug release tests showed that the drug release from the hydrogel was pH‐dependent, with 96% of the model drug released in a neutral environment, compared to 28% released in an acidic medium. These hydrogels could have potential in pH‐sensitive drug delivery. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 356–367     

Poly(hexamethylene guanidine)‐based hydrogels with long lasting antimicrobial activity and low toxicity

Long lasting antimicrobial activity and low toxicity are essentials for hydrogels in biomedicine. However, most reported hydrogels cannot combine these characteristics. In this work, poly (hexamethylene guanidine) hydrochloride (PHMG), a cheap cationic polymer with two terminal amino groups, was first modified with methacrylic anhydride to give PHMG dimethacrylamide (PHMGDMAAm), which was further used to prepare hydrogels with acrylamide (AAm) under ultraviolet irradiation in the presence of α‐ketoglutaric acid (α‐KGA) as photoinitiator in aqueous medium. The resultant hydrogels showed strong antibacterial activity against both Gram‐negative and Gram‐positive bacteria due to the PHMG segments in the hydrogel backbone. Moreover, the antimicrobial activity of the hydrogels did not decrease significantly after being soaked in water for one month and washed by water frequently for many times. Hemolysis and cytotoxicity assays demonstrated the excellent biocompatibility of the PHMG‐PAAm hydrogels. This kind of low cost cationic hydrogels with long lasting antimicrobial activity and low toxicity is expected to have potential applications in biomedicine. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2027–2035     

Polyacrylamide cryogels by photoinitiated free radical polymerization

A novel method for the preparation of poly(acrylamide) cryogels by photoinitiated polymerization of monomeric precursors was described. A series of poly(acrylamide) cryogels were easily prepared by irradiating aqueous solutions containing acrylamide and N,N′‐methylene(bis)acrylamide as monomer and cross‐linker, respectively, in the presence of 1‐[4‐(2‐hydroxyethoxy)phenyl]‐2‐hydroxy‐2‐methyl‐1‐propane‐1‐one (Irgacure 2959) as water‐soluble photoinitiator with the help of freezing–thawing procedures. Photolysis was conducted at ?13 °C isothermally through specially designed cryostat‐integrated Rayonet merry‐go‐round photoreactor. On comparing the described photochemical method with the conventional redox counter part, the polymerization is initiated, and gelation proceeds only on external stimulation by light. This way, concomitant hydrogel formation usually observed with the redox process as a result of premature polymerization during the cooling process was prevented. The obtained cryogels exhibited superfast swelling behavior. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and swelling behavior of comb‐type grafted hydrogels by reversible addition–fragmentation chain transfer polymerization

The comb‐type grafted hydrogels poly(N‐isopropylacrylamide)‐g‐poly(N‐isopropylacrylamide) (PNIPAM‐g‐PNIPAM) and poly(acrylic acid)‐g‐poly(N‐isopropylacrylamide) (PAAc‐g‐PNIPAM) were prepared by reversible addition–fragmentation chain transfer polymerization. A macromolecular chain‐transfer agent was prepared first. Then, hydrogels were obtained by a reaction with a comonomer (N‐isopropylacrylamide or acrylic acid) in the presence of N,N‐methylenebisacrylamide as a crosslinker. The equilibrium swelling ratios and the swelling and deswelling kinetics of PNIPAM‐g‐PNIPAM were measured. The effects of the chain length and amount on the swelling behavior were investigated. The deswelling mechanism was illustrated. Meanwhile, the PAAc‐g‐PNIPAM hydrogel was used to confirm the versatility of this novel method. It was prepared in an alcoholic medium, whereas hydrogen‐bonding complexes formed in 1,4‐dioxane, which was chosen as the reaction medium for the PNIPAM‐g‐PNIPAM hydrogel. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2615–2624, 2005     

Thermosensitive molecularly imprinted hydrogel cross‐linked with N‐malely chitosan for the recognition and separation of BSA

A novel temperature‐sensitive molecularly imprinted hydrogel composed of N‐isopropylacrylamide and acrylamide has been prepared by using free‐radical polymerization and was cross‐linked by modified water‐soluble N‐maley chitosan in aqueous solution. BSA (pI 4.9, MW 66.0 kDa) was used as the template protein. The produced hydrogels were characterized by environmental SEM to reveal the microcosmic morphology. A microporous structure was only found in the imprinted hydrogel, while no obvious microporous structure was found in nonimprinted hydrogels. The lower critical solution temperature of the hydrogels was 34°C, and the optimal binding conditions were tested, namely, the adsorption equilibrium time of 6 h and initial BSA concentration of 1.0 mg/mL. The adsorption capacity Q_max was determined by Langmuir isotherm plots and was 5.72 mg/g for imprinted hydrogel and 1.18 mg/g for nonimprinted hydrogels. A separation factor (β) of 4 was obtained when bovine hemoglobin (pI 6.9, MW 64.0 kDa) was selected as the particular reference protein. Molecular weights and pIs were chosen to investigate the selectivity of the hydrogels. It was shown that the shape memory and the size effect were the major factors for the recognition. This imprinted hydrogel was used to specifically adsorb the BSA from the protein mixture.