Compressive stress relaxation of metallocene‐based polyolefin foams: Effect of gamma‐ray‐induced crosslinking

Metallocene‐based polyolefin (MPO) foams possess a closed‐cell structure which is in contrast to the open‐celled structure of polyurethane (PU) foams. In this study, we investigate the effects of gamma‐irradiation on the mechanical behavior of MPO foams using PU foam behavior as a basis. Compressive step‐strain experiments reveal a two‐step relaxation process in MPO foams, dominated by polymer chain relaxation at short times and gas diffusion from the closed cells at longer times. On the other hand, the relaxation in PU foams is similar to fully crosslinked polymers with the relaxation modulus reaching an equilibrium value after an initial decay. The closed‐celled structure of MPO foams lends to rapid stress relaxation and low structural recoverability upon application of compressive loads. Exposure to gamma radiation induces crosslinking in MPO foams and improves their resilience and recoverability. Stress relaxation tests reveal that nonradiated MPO foams show complete relaxation and structural loss at high temperatures. In contrast, radiated MPO foams show a significant retardation in relaxation kinetics and structural stability attributed to radiation‐induced crosslinking. Dynamic rheology and solvent‐extraction studies also support the results obtained from stress‐relaxation experiments. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1045–1056, 1999     

Bioreducible and core‐crosslinked hybrid micelles from trimethoxysilyl‐ended poly(ε‐caprolactone)‐S‐S‐poly(ethylene oxide) block copolymers: Thiol‐ene click synthesis and properties

Bioreducible and core‐crosslinked hybrid micelles were for the first time fabricated from biodegradable and biocompatible trimethoxysilyl‐terminated and disulfide‐bond‐linked block copolymers poly(ε‐caprolactone)‐S‐S‐poly(ethylene oxide), which were prepared by combining thiol‐ene coupling reaction and ring‐opening polymerization. The molecular structures, physicochemical, self‐assembly, and bioreducible properties of these copolymers were thoroughly characterized by means of FTIR, ¹H NMR, gel permeation chromatography, differential scanning calorimetry, wide‐angle X‐ray diffraction, dynamic light scattering (DLS), and transmission electron microscopy. The core‐crosslinking sol‐gel reaction was confirmed by ¹H NMR, and the core‐crosslinked hybrid micelles contained about 3 wt % of silica. The bioreducible property of both uncrosslinked and core‐crosslinked micelles in 10 mM 1,4‐dithiothreitol (DTT) solution was monitored by DLS, which demonstrated that the PEO corona gradually shedded from the PCL core. The anticancer doxorubicin drug‐loaded micelles showed nearly spherical morphology compared with blank micelles, presenting a DTT reduction‐triggered drug‐release profile at 37 °C. Notably, the core‐crosslinked hybrid micelles showed about twofold drug loading capacities and a half drug‐release rate compared with the uncross‐liked counterparts. This work provides a useful platform for the fabrication of bioreducible and core‐crosslinked hybrid micelles potential for anticancer drug delivery system. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Functionalization of surface‐grafted polymethylhydrosiloxane thin films with alkyl side chains

Thin films of crosslinked polymethylhydrosiloxane (PMHS) have been grafted on silica using the sol–gel process allowing further functionalization by effective quantitative hydrosilylation of SiH groups by olefins within the network. Postfunctionalization gives the polysiloxane network with n‐alkyl side chains. The PMHS coating was prepared by room temperature polycondensation of a mixture of methyldiethoxysilane HSiMe(OEt)₂ monomer and triethoxysilane HSi(OEt)₃ (TH) as crosslinker. The surface‐attached films are chemically stable and covalently bonded to the silica surface. Subsequently, films were functionalized without delamination. We showed by FTIR spectroscopy how the crosslinking ratio and the molecular size of the alkenes precursors influence the extent of the hydrosilylation reaction of SiH groups in the PMHS network. We have determined that quasi‐full olefin addition catalyzed by a platinum complex occurred within soft networks of less than 5% TH with 1‐alkenes CH₂?CH(CH₂)_n‐2CH₃ of various alkyl chain lengths (n = 5, 11, 17). Powders of PMHS gel were also modified with 1‐alkenes by hydrosilylation. The SiH groups within the soft gel (5% crosslinked) were fully functionalized as shown by ²⁹Si and ¹H solid‐state NMR. The structure of functionalized polysiloxane with n‐octadecyl and n‐dodecyl side chains was studied by FTIR, wide angle X‐ray diffraction, and DSC showing crystallization of the long n‐alkyl chains in the network. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3546–3562, 2008     

Electro‐conductive double‐network hydrogels

Novel electro‐conductive and mechanically‐tough double network polymer hydrogels (E‐DN gels) were synthesized by polymerization of 3, 4‐ethylenedioxythiophene in the presence of a double network hydrogel (DN gel) matrix. The E‐DN gels showed not only excellent mechanical performance, having a fracture stress of 1.4–2.1 MPa, but also electrical conductivity as high as 10^?3 S cm^?1, both under dry and water‐swollen states. The fracture stress and fracture energy of the E‐DN gel was increased by 1.7 and 3.4 times, respectively, as compared with the DN gel. From scanning electron microscope and AFM observations, it was found that electro‐conductive poly(3,4‐ethylenedioxythiophene) (PEDOT) was incorporated into DN gel matrix, apparently due to the formation of a poly‐ion complex with sulfonic acid group of the DN gel network. Thus, PEDOT incorporated into the DN gel matrix greatly improves not only electronic conductivity, but also mechanical properties, reinforcing the double network gel matrix. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Environmentally Stable Polymer Gels with Super Deformability and High Recoverability Enhanced by Sub‐5 nm Particles in the Nonvolatile Solvent

It remains challenging to satisfy the combined performances for hydrogels with excellent mechanical behavior, high deformability, and super recoverability under harsh environmental conditions. In this study, we first established a strong polymer network via the crosslinking of polymer chains on the surfaces of sub‐5‐nm calcium hydroxide nanospherulites in ethylene glycol solvent. The organic gel expressed excellent mechanical properties such as a recoverable compressive engineering stress of 249 MPa and an elongation stress of 402 KPa, which was attributed to the uniform nanosized crosslinking structure as characterized by SEM. Moreover, the nonvolatile solvent remained in the gel, meaning that the sample can resist a wide temperature range of ?56 to 100 °C without losing the elastic properties. This novel organic gel could provide promising routes to develop the ideal elastic carriers for wearable devices, smart skin sensors, and damping materials. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 713–721     

Production of crosslinked,hollow nanoparticles by surface‐initiated living free‐radical polymerization

Surface‐initiated living free‐radical polymerization is employed in a multistep procedure to prepare hollow polymeric nanocapsules. Initially, trichlorosilyl‐substituted alkoxyamine initiating groups are attached to the surface silanol groups of silica nanoparticles. This surface layer of initiating groups is then used to grow functionalized linear chains leading to a core–shell morphology. The choice of functional groups is governed by their ability to undergo facile crosslinking reactions, with both active ester and benzocyclobutene groups being examined. Under either chemical or thermal conditions, the reaction of these functionalities gives a crosslinked polymeric shell that is covalently attached to, and surrounds, the central silica core. Removal of the silica core with HF then gives the hollow polymeric nanocapsules, which are stable under solvent dissolution and thermal treatment because of their crosslinked structure. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1309–1320, 2002     

Nafion®/(organically modified silicate) nanocomposites via polymer in situ sol–gel reactions: Mechanical tensile properties

A series of Nafion®/[organically modified silicate (ORMOSIL)] hybrid materials have been created by in situ sol–gel copolymerizations of tetraethylorthosilicate and semiorganic silicon alkoxide monomers. The trends in the mechanical tensile properties of these hybrid materials were largely rationalized in terms of the entrapment of the long sulfonic acid side chains in silicate or ORMOSIL structures. There is a significant increase in the mechanical strength relative to that of unfilled Nafion®, except in one case. Young's modulus is enhanced relative to that of unfilled acid form Nafion® in a number of cases, although the degree of ductility is reduced relative to that of unfilled Nafion®. The filler fractions are beneath a critical value that would reflect percolation of a glassy, direct load‐bearing silicate phase. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2237–2247, 2002     

A facile and controllable synthesis of dual‐crosslinked elastomers based on linear bifunctional polydimethylsiloxane oligomers

Dual‐crosslinked supramolecular elastomers with the hybrid network consisting of hydrogen bonds and covalent bonds combine the reversibility of hydrogen bond and mechanical properties of covalent crosslinking network. In this article, isocyanate mixture is used as curing agent to prepare dual‐crosslinked elastomer based on bifunctional polydimethylsiloxane under mild condition. This method can effectively build up a hybrid network with the designed structure. A series of elastomers with same hydrogen bond density and variable covalent crosslinking degree are obtained. Swelling measurements and ¹H‐NMR spectra confirm the feasibility and controllability of curing method, the increasing of bifunctional isocyanate give rise to higher covalent crosslinking degree, improving the solvent resistance. The studies on viscoelastic property show that the introduction of an irreversible covalent crosslinking network stabilize the hybrid network, restrain the chain movement. The mechanical and self‐healing property studies reveal that the covalent crosslink significantly reinforce the whole network, while the reparable strength seems to mainly depend on the hydrogen bond density. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3760–3768     

A comparative study of phosphoric acid‐doped m‐PBI membranes

Phosphoric acid (PA)‐doped m‐polybenzimidazole (PBI) membranes used in high temperature fuel cells and hydrogen pumps were prepared by a conventional imbibing process and a sol–gel fabrication process. A comparative study was conducted to investigate the critical properties of PA doping levels, ionic conductivities, mechanical properties, and molecular ordering. This systematic study found that sol–gel PA‐doped m‐PBI membranes were able to absorb higher acid doping levels and to achieve higher ionic conductivities than conventionally imbibed membranes when treated in an equivalent manner. Even at similar acid loadings, the sol–gel membranes exhibited higher ionic conductivities. Heat treatment of conventionally imbibed membranes with ≤29 wt % solids caused a significant reduction in mechanical properties; conversely, sol–gel membranes exhibited an enhancement in mechanical properties. From X‐ray structural studies and atomistic simulations, both conventionally imbibed and sol–gel membranes exhibited d‐spacings of 3.5 and 4.6 Å, which were tentatively attributed to parallel ring stacking and staggered side‐to‐side packing, respectively, of the imidazole rings in these aromatic heterocyclic polymers. An anisotropic staggered side‐to‐side chain packing present in the conventional membranes may be related to the reduction in mechanical properties. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Polym. Phys. 2014 , 52, 26–35     

Development of Gelatin‐Alginate Hydrogels for Burn Wound Treatment

Hydrogels are interesting as wound dressing for burn wounds to maintain a moist environment. Especially gelatin and alginate based wound dressings show strong potential. Both polymers are modified by introducing photocrosslinkable functionalities and combined to hydrogel films (gel‐MA/alg‐MA). In one protocol gel‐MA films are incubated in alg‐MA solutions and crosslinked afterward into double networks. Another protocol involves blending both and subsequent photocrosslinking. The introduction of alginate into the gelatin matrix results in phase separation with polysaccharide microdomains in a protein matrix. Addition of alg(‐MA) to gel‐MA leads to an increased swelling compared to 100% gelatin and similar to the commercial Aquacel Ag dressing. In vitro tests show better cell adhesion for films which have a lower alginate content and also have superior mechanical properties. The hydrogel dressings exhibit good biocompatibility with adaptable cell attachment properties. An adequate gelatin‐alginate ratio should allow application of the materials as wound dressings for several days without tissue ingrowth.     

A novel shape memory poly(ε‐caprolactone) network via UV‐triggered thiol‐ene reaction

A facile method to prepare shape memory polymers crosslinked by SiO₂ is described. A series of biodegradable shape memory networks were obtained through thiol‐ene reaction triggered by UV irradiation between surface‐thiol‐modified SiO₂ nanoparticles and end‐acrylate poly (ε‐caprolactone) (PCL). The highly selective thiol‐ene reaction ensured a uniform distribution of PCL chains between crosslinkers, contributing well‐defined network architecture with enhanced mechanical and shape‐memory properties. Thiol‐functionalized silica nanoparticle was characterized by using FTIR and XPS analysis, and ¹H NMR spectra was used to confirm the successful modification of terminal hydroxyl group of PCL diol. Surface‐modified silica particles were found well dispersible in acrylate‐capped PCL supported by SEM. Thermal and crystalline behaviors of the obtained polymers were analyzed by DSC and XRD, and DMA measurement proved good mechanical property. The shape memory behavior and tensile strength was somewhat tunable by the length of PCL. Acceptably, sample SiO₂‐SMP2k presented 99% recovery ratio and 97% shape fixity, and its relatively high tensile strength showed an attractive potential for biomedical application. Finally, a possible molecular mechanism accounting for the shape memory property was illustrated. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 692–701     

Actuation design for high‐performance shape memory polyurethanes

A series of shape memory polyurethanes were synthesized from poly(tetramethylene glycol), 4,4‐methylene diphenyl diisocyanate, and 1,3‐butanediol. The prepolymers with different molecular weights (M_c) were capped with 2‐hydroxyl ethylacrylate or 3‐aminopropyltriethoxysilane (APTES) and crosslinked by UV curing or a sol–gel reaction. Variations of the crosslinker functionality (f), subchain density (N), and hard segment content (HSC) produced systematic variations of the glass transition temperature (6–45 °C), accompanied by changes in the mechanical, dynamic mechanical and shape memory properties. More than 95% of shape fixity and 98% of shape recovery up to the fourth cycles were obtained with APTES crosslinked 3000M_c with 30% of HSC. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1473–1479     

Phosphorus‐containing renewable polyester‐polyols via ADMET polymerization: Synthesis,functionalization, and radical crosslinking

An α,ω‐diene containing hydroxyl groups was prepared from plant oil‐derived platform chemicals. The acyclic diene metathesis copolymerization (ADMET) of this monomer with a phosphorus‐containing α,ω‐diene (DOPO II), also plant oil derived, afforded a series of phosphorus containing linear polyesters, which have been fully characterized. The backbone hydroxyls of these polyesters have been acrylated and radically polymerized to produce crosslinked polymers. The thermomechanical and mechanical properties, the thermal stability, and the flame retardancy of these phosphorus‐based thermosets have been studied. Moreover, methyl 10‐undecenoate has been used as chain stopper in selected ADMET polymerizations to study the effect of the prepolymers' molecular weights on the different properties of the final materials. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1649–1660, 2010     

Synthesis of polyethylene oxide graft polysilylenes and networks based on poly(di‐n‐pentylsilylene/n‐pentyloct‐7‐enyl) copolymers

Poly(dipentylsilylene) copolymers containing n‐pentyl‐n‐oct‐7‐enylsilane units were prepared by reductive coupling of the corresponding dichlorosilanes. Linear high molecular weight and some crosslinked polymer were obtained. The soluble products exhibited optical and thermal properties like poly(dipentylsilylene). Differential scanning calorimetry was used to investigate crystallization and to monitor thermal crosslinking. Vinyl functionalized side chains were hydrosilylated with dipentylsilane and dimethylchlorosilane and crosslinked via the side chains. Hydrosilylation with di‐n‐pentyl(trimethylsiloxypropyl)silane led to a partial hydroxy functionalization of the polysilylene and enabled anionic PEO grafting of the poly(dipentylsilylene). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2306–2318, 2000     

Synthesis of crosslinked poly(butyl methacrylate‐co‐pentaerythritol triacrylate) gel by single electron transfer‐living radical polymerization and its oil‐absorbing properties

A novel high oil‐absorbing crosslinked gel was synthesized by copolymerization of butyl methacrylate (BMA) with a small amount of pentaerythritol triacrylate (PETA) crosslinker using single electron transfer‐living radical polymerization (SET–LRP) initiated with carbon tetrachloride (CCl₄) and catalyzed by Cu(0)/hexamethylenetetramine (HMTA) in N, N‐dimethylformamide (DMF). The polymerization followed first‐order kinetics as indicated by linear increase of monomer concentration with reaction time. Effects of reaction temperature, crosslinker, initiator, and catalyst on the oil‐absorbing properties of the crosslinked gel were investigated in detail. The oil absorptions of the crosslinked gel to chloroform, toluene could reach 51.9, 34.5 g/g, respectively. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Strain stiffening and negative normal stress in alginate hydrogels

Alginate hydrogels are polysaccharide biopolymer networks widely useful in biomedical and food applications. Here, we report nonlinear mechanical responses of ionically crosslinked alginate hydrogels captured using large amplitude oscillatory shear experiments. Gelation was performed in situ in a rheometer and the rheological investigations on these samples captured the strain‐stiffening behavior for these gels as a function of oscillatory strain. In addition, negative normal stress was observed, which has not been reported earlier for any polysaccharide networks. The magnitude of negative normal stress increases with the applied strain amplitude and can exceed that of the shear stress at large‐strain. Fitting a constitutive relationship to the stress‐strain curves reveals that the mode of deformation involves stretching of the alginate chains and bending of both the chains and the junction zones. The contribution of bending increases near saturation of G blocks as Ca²⁺ concentration was increased. The results presented here provide an improved understanding of the deformation behavior of alginate hydrogels and such understanding can be extended to other crosslinked polysaccharide networks. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1767–1775     

Ionic liquid‐based organic–inorganic hybrid electrolytes: Impact of in situ obtained and dispersed silica

Organic–inorganic hybrid electrolytes based on PEO‐NaTFSI‐ionic liquid (HMIMTFSI)‐silica (in situ production via sol gel process) are being reported in this article. The variation in conductivity with ionic liquid (IL) addition has been explained on the basis of number of free TFSI anions evaluated using ATR‐IR data. The deconvolution of the IR spectra of these hybrid electrolytes has given evidence of ion‐pair formation which has been compared vis‐á‐vis the conductivity variation. The hybrid electrolyte with maximum conductivity comprises the highest number of free imide ions and has lowest glass transition temperature. FESEM has displayed a porous and layered surface morphology with dispersed silica nanoparticles. In addition, the optimized hybrid electrolyte has been compared with 5 wt% (limit of mechanical stability) ex situ silica added composite where the temperature cycling of conductivity has shown that the ex situ dispersed hybrid electrolytes do not retrace their conductivity path contrary to the in situ prepared hybrid electrolytes. This behavior has been explained to be due to the hindrance offered by the ex situ added silica in the recrystallization kinetics of PEO. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 207–218     

Aliphatic Polyester/polyhedral Oligomeric Silsesquioxanes Hybrid Networks via Copper‐free 1,3‐dipolar Cycloaddition Click Reaction

In this study, we describe the preparation and characterization of a new class of thermoset hybrid networks containing aliphatic polyester and polyhedral oligomeric silsesquioxanes (POSS). The copper‐free 1,3‐dipolar cycloaddition click reaction of internal alkyne functionalized aliphatic polyester and multifunctional azido POSS with different concentrations led to highly crosslinked thermoset networks. The click reactions performed under ambient conditions (i.e., in tetrahydrofuran at room temperature for 1 day) in the absence of any catalyst. The chemical composition of hybrid networks and homogenous distribution of POSS molecules were confirmed by Fourier transform infrared spectroscopy and scanning electron microscopy with energy dispersive spectroscopy. The swelling ratios of hybrid networks were commonly decreased by increasing POSS‐N₃ content and by changing polar solvents to apolar solvents. Thermogravimetric analysis results demonstrated that the thermal stability of hybrid networks increased with higher POSS feeding ratio. Tensile tests were applied to evaluate the mechanical properties of hybrid networks. Compared to neat aliphatic polyester, the mechanical properties of hybrid networks significantly improved. For instance, the tensile strength were enhanced from 5 MPa to 19 MPa by increasing the concentration of azido functionalized POSS from 10 to 40. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2222–2227     

Epoxy‐functionalized,low‐glass‐transition‐temperature latex. II. Interdiffusion versus crosslinking in the presence of a diamine

This article describes the results of experiments examining the competition between the polymer diffusion rate and the crosslinking rate in low‐glass‐transition‐temperature, epoxy‐containing latex films in the presence of a diamine. We examined films formed from donor‐ and acceptor‐labeled poly(butyl acrylate‐co‐methyl methacrylate‐co‐glycidyl methacrylate) copolymer latex and studied the influence of several parameters on the growth rate of gel content and the rate of polymer diffusion. These factors include the molecular weight of the latex polymer, the presence or absence of a diamine crosslinking agent, and the cure protocol. The results were compared to the predictions of a recent theory of the competition between crosslinking and polymer diffusion across interfaces. In the initially formed films, polymer diffusion occurs more rapidly than the chemical reaction rate. Therefore, these films fall into the fast‐diffusion category of this model. In our system (unlike in the model), the latex polymer has a broad distribution of molecular weights and a distribution of diffusivities. The shortest chains contribute to the early time diffusion that we measure. At later stages of our experiment, slower diffusing species contribute to the signal that we measure. The diffusion time decreases substantially, and we observe a crossover to a regime in which the chemical reaction dominates. The increases in chain branching and gel formation bring polymer diffusion to a halt. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4098–4116, 2002     

Photo‐induced thiol‐ene polysulfide‐crosslinked materials with tunable thermal and mechanical properties

Photo‐induced thiol‐ene crosslinked polymeric networks have been extensively explored in constructing a variety of new materials with enhanced mechanical properties for optical, biomedical, and sensing applications. Toward the broad applications, however, tunable mechanical properties are greatly desired. Here, an effective approach utilizing high‐molecular‐weight methacrylate copolymers having pendant thiol and vinyl groups (MCPsh and MCPenes) to modulate thermal and mechanical properties of photo‐induced thiol‐ene crosslinked materials is reported. The MCP copolymers are synthesized by an industrially friendly polymerization method, followed by post‐modification including either a facile coupling reaction or reductive cleavage. Upon UV irradiation, thiol‐ene reactive blends of MCPsh and MCPenes yield highly crosslinked materials through the formation of flexible sulfide linkages. These polysulfide‐crosslinked materials based on rigid MCP backbones exhibit enhanced mechanical properties. Further, their thermal and mechanical properties are tuned by modulating monomer compositions of MCPs as well as varying numbers of pendant SH or vinyl groups (i.e., extent of crosslinking densities). This approach is versatile and effective for development of high performance polymeric materials. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3060–3068