Effect of structural,redox and acid characteristics of M<Subscript>x</Subscript>O<Subscript>y</Subscript>/ZrO<Subscript>2</Subscript>(Al<Subscript>2</Subscript>O<Subscript>3</Subscript>) (M-Mn,Co, Cr) oxide nanocomposites on their catalytic properties in the deep oxidation of methane

Alumina-and zirconia-manganese catalysts for the deep oxidation of methane were studied by X-ray phase analysis, temperature-programmed hydrogen reduction, and IR spectroscopy. The most active catalyst has the optimal combination of dimensional, redox, and acid characteristics. The zirconia-manganese catalysts formed on the surface of a kaolin-aerosil honeycomb matrix provides for 80–100% conversion of methane to CO₂ at 690–750 °C. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 43, No. 6, pp. 367–372, November–December, 2007.     

Role of rare-earth element oxides in catalysts for the oxidative conversion of methane based on Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

It has been established that oxides of the rare-earth elements with moderate redox potentials (La₂O₃, CeO₂) increased the activity and working stability of Ni-Al₂O₃/cordierite catalysts in the reactions of deep and partial oxidation of methane. In the presence of the (NiO + La₂O₃ + Al₂O₃)/cordierite catalyst the process of carbon dioxide conversion of methane can be intensified by introduction of oxygen into the reaction gas mixture which decreases the temperature to achieve high conversion to 75–100 °C and has practically no effect on selectivity with respect to H₂. Translated from Teoreticheskaya i éksperimental'naya Khimiya, Vol. 44, No. 6, pp. 359–364, November–December, 2008.     

Sulfur resistance and stability of yttrium-stabilized binary Co-Cu and Ni-Cu composites with zirconium dioxide in the oxidative conversion of methane

Binary Co-Cu and Ni-Cu composites with YSZ have demonstrated rather high thermal resistance (up to 1000 °C) and stability in the extensive oxidation of methane. The tendency of the nickel–copper composites to carbon deposition depends on the amount of nickel introduced. The higher stability was found for the sample with active phase containing 4% Ni, 16% Cu. The sulfur resistance of the palladium-doped Ni–Cu composite is attributed to the formation of an adsorbed [PdO·SO₂] complex. TPHR data indicated that the oxygen in this sample is less reactive in methane oxidation.     

Influence of H<Subscript>2</Subscript>O and SO<Subscript>2</Subscript> on the activity of deposited cobalt oxide catalysts in the processes of reduction of nitrogen(I), (II) oxides with carbon monoxide and C<Subscript>3</Subscript>-C<Subscript>4</Subscript> alkanes

It is shown that palladium–cobalt oxide–cerium catalyst deposited on cordierite catalyzes the reduction of nitrogen(II) oxide with carbon monoxide, and cobalt–iron catalysts in simultaneous reduction of NO + N₂O with C₃-C₄ alkanes retained high activity in the presence of water vapor and sulfur dioxide. The Pd-Co₃O₄/cordierite catalyst exceeds the Pt-Co₃O₄/codierite catalyst in the conversion of NO and CO in the reaction mixture CO + NO + O₂ + H₂O + SO₂. Modification of the Pd-Co₃O₄/cordierite with cerium oxide considerably increases its sulfur resistance.     

Effect of the composition and structural and size characteristics of composites based on stabilized zirconia and transition metal (Cu,Co, Ni) oxides on their catalytic properties in methane oxidation reactions

The effects of transition metal (Cu, Co, Ni) oxides and platinum-group metals (Pt, Pd, Rh) in composites based on Y(Sc)-stabilized zirconia on their catalytic properties (activity, selectivity, sulfur resistance) and service life characteristics (thermal stability, performance stability) in methane oxidation reactions have been investigated. The high activity of the composites (75–99% methane conversion at 600–800°C) correlates with the amount and mobility of surface oxygen in these materials. The promoting effect of the platinum-group metals depends on the composition of the reaction medium (on whether it corresponds to the partial or total methane oxidation and on whether it contains sulfur dioxide).     

Influence of the composition of carriers based on ZrO<Subscript>2</Subscript> and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> on the properties of cobalt-containing catalysts on the selective reduction of NO with methane

A series of cobalt-containing granulated and structured catalysts based on zirconium and aluminum oxides has been studied. The optimum composition of binary oxide samples (80% ZrO₂ − 20% Al₂O₃) for the selective reduction of nitrogen monoxide with methane (84% conversion of NO achieved at 320 °C) has been determined. The activity of the structured catalysts depends on both the composition of the secondary carrier (ZrO₂, Al₂O₃, and their mixture) and on the nature of the skeleton of the cellular structure (cordierite, kaolin-aerosil). __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 43, No. 4, pp. 237–241, July–August, 2007.     

Effect of the alkoxides addition order on the properties of Pd/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–ZrO<Subscript>2</Subscript> catalysts used for methane combustion

A series of Pd/Al₂O₃–ZrO₂ catalysts were prepared to be used in methane oxidation. The effect of the addition order of metal alkoxides on the texture, structure and catalytic properties of the solids is studied. The control of the preparation parameters is achieved via sol gel way as an attractive route of the preparation of these catalysts. N₂ physisorption, XRD, Scanning Electronic Microscopy (SEM) and H₂ chemisorption are the main techniques used to characterize the prepared Pd/Al₂O₃–ZrO₂ catalysts. Textural analysis reveals the mesoporosity of all the catalysts independently of the addition order of alkoxides while surface area is more pronounced when the aluminium alkoxide is added before or with the zirconium precursor. XRD patterns show the development of the zirconia tetragonal phase for all the catalysts. Better metallic dispersion is obtained when aluminium alkoxide is added first which can be justified by the high homogeneity observed on the corresponding catalyst as revealed by SEM technique.     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.     

Oxidative conversion of methane and methanol on M/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/cordierite structured metal oxide catalysts (m = Ni,Cu, Zn)

A study was carried out on the properties of Ni/Al₂O₃ and Cu-ZnO/Al₂O₃ composites supported on ceramic honeycomb monoliths made from synthetic cordierite in the carbon dioxide conversion of methane and the partial oxidation of methanol. The structured nickel-alumina catalysts are significantly more efficient than the conventional granulated catalysts. The improved working stability of these catalysts was achieved by adjusting the acid-base properties of the surface by introducing sodium and potassium oxides, which leads to inhibition of surface carbonization. The hydrogen yield was close to 90% in the partial oxidation of methanol with a stoichiometric reagent ratio in the presence of the Cu-ZnO/Al₂O₃/cordierite catalyst. A synergistic effect was found, reducing the selectivity of CO formation in the presence of the Cu-ZnO catalyst relative to samples derived from the individual components Cu and ZnO. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 43, No. 5, pp. 299–306, September–October, 2007.     

New organic metal β-(DOET)<Subscript>2</Subscript>FSO<Subscript>3</Subscript> · H<Subscript>2</Subscript>O: Synthesis and crystal structure

An organic metal β-(DOET)₂FSO₃ · H₂O based on a novel donor DOET (DOET is (1,4-dioxane-2,3-diyldithio)ethylenedithiotetrathiafulvalene) was synthesized and structurally characterized. Single crystals were prepared by electrochemical oxidation of DOET in the d.c. mode. The salt has a layered structure with the DOET^1/2+ radical cation layers parallel to the ab plane. The FSO ₃ ⁻ anion is equiprobably disordered over two positions relative to the center of symmetry (1/2, 0, 0). The temperature behavior of conductivity is characteristic of metals in the temperature range from 293 down to 96 K; below 96 K, an increase in resistance is observed. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 2387–2389, October, 2005.     

LaNi<Subscript>0.5</Subscript>Ti<Subscript>0.5</Subscript>O<Subscript>3</Subscript>/CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>-based sensor for sensitive determination of paracetamol

A novel electrochemical sensor based on LaNi_0.5Ti_0.5O₃/CoFe₂O₄ nanoparticle-modified electrode (LNT–CFO/GCE) for sensitive determination of paracetamol (PAR) was presented. Experimental conditions such as the concentration of LNT–CFO, pH value, and applied potential were investigated. Under the optimum conditions, the electrochemical performances of LNT–CFO/GCE have been researched on the oxidation of PAR. The electrochemical behaviors of PAR on LNT–CFO/GCE were investigated by cyclic voltammetry. The results showed that LNT–CFO/GCE exhibited excellent promotion to the oxidation of PAR. The over-potential of PAR decreased significantly on the modified electrode compared with that on bare GCE. Furthermore, the sensor exhibits good reproducibility, stability, and selectivity in PAR determination. Linear response was obtained in the range of 0.5 to 901 μM with a detection limit of 0.19 μM for PAR.     

Oxidation of hydrogen on previously reduced Ta<Subscript>2</Subscript>O<Subscript>5</Subscript> with Pt and Pd additives

X-ray photoelectron spectroscopy (XPS) was used to establish that the surface layer of catalysts obtained by the reduction of Ta₂O₅ with added Pt and Pd by hydrogen contains nonstoichiometric oxides TaO_x, which enhance the activity of the catalyst. A study of the hydrogen oxidation kinetics showed that the kinetic relationships are described satisfactorily by the Eley-Riedel mechanism, according to which the reaction occurs by an interaction of hydrogen from the gas phase with adsorbed oxygen. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 44, No. 4, pp. 254–258, July–August, 2008.     

Structure and Catalytic Properties of Ceria-based Nickel Catalysts for CO<Subscript>2</Subscript> Reforming of Methane

Carbon dioxide reforming (CDR) of methane to synthesis gas over supported nickel catalysts has been reviewed. The present review mainly focuses on the advantage of ceria based nickel catalysts for the CDR of methane. Nickel catalysts supported on ceria–zirconia showed the highest activity for CDR than nickel supported on other oxides such as zirconia, ceria and alumina. The addition of zirconia to ceria enhances the catalytic activity as well as the catalyst stability. The catalytic performance also depends on the crystal structure of Ni–Ce–ZrO₂. For example, nickel catalysts co-precipitated with Ce_0.8Zr_0.2O₂ having cubic phase gave synthesis gas with CH₄ conversion more than 97% at 800 °C and the activity was maintained for 100 h during the reaction. On the contrary, Ni–Ce–ZrO₂ having tetragonal phase (Ce_0.8Zr_0.2O₂) or mixed oxide phase (Ce_0.5Zr_0.5O₂) deactivated during the reaction due to carbon formation. The enhanced catalytic performance of co-precipitated catalyst is attributed to a combination effect of nano-crystalline nature of cubic Ce_0.8Zr_0.2O₂ support and the finely dispersed nano size NiO _x crystallites, resulting in the intimate contact between Ni and Ce_0.8Zr_0.2O₂ particles. The Ni/Ce–ZrO₂/θ–Al₂O₃ also exhibited high catalytic activity during CDR with a synthesis gas conversion more than 97% at 800 °C without significant deactivation for more than 40 h. The high stability of the catalyst is mainly ascribed to the beneficial pre-coating of Ce–ZrO₂ resulting in the existence of stable NiO _x species, a strong interaction between Ni and the support, and an abundance of mobile oxygen species in itself. TPR results further confirmed that NiO _x formation was more favorable than NiO or NiAl₂O₄ formation and further results suggested the existence of strong metal-support interaction (SMSI) between Ni and the support. Some of the important factors to optimize the CDR of methane such as reaction temperature, space velocity, feed CO₂/CH₄ ratio and H₂O and/or O₂ addition were also examined.     

Catalytic Activity of WO<Subscript>3</Subscript> and MoO<Subscript>3</Subscript> with Pt and Pd Additives in Oxidation of Hydrogen

We have shown that WO₃ and MoO₃ with Pt or Pd additives exhibit high catalytic activity in the reaction of H₂ oxidation. In the temperature range 313 K to 353 K, we have studied the kinetic behavior of the reaction on 0.1 mass % Pt(Pd)/WO₃ and Pt(Pd)/MoO₃ samples. We have established that the kinetics of H₂ oxidation on these catalysts correspond to an Eley - Rideal mechanism. __________ Translated from Teoreticheskaya i Eksperimental'naya Khimiya, Vol. 41, No. 5, pp. 313–316, September–October, 2005.     

Chain termination mechanism in the Fischer-Tropsch synthesis on a Co/SiO<Subscript>2</Subscript>Zr(IV) catalyst at elevated pressure

The mechanism for the formation of C₂₊ paraffins differs from the mechanism for the formation of methane. While methane is obtained due to hydrogenation of methyl groups, C₂₊ hydrocarbons are formed as the result of the conversion of alkyl intermediates into hydroalkene intermediates, which can decompose to give olefins or undergo hydrogenation to give saturated hydrocarbons. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 44, No. 3, pp. 175–179, May–June, 2008.     

Properties of the surface layer and catalytic activity of Ta<Subscript>2</Subscript>O<Subscript>5</Subscript> with Pt or Pd additives in the oxidation of hydrogen

The catalytic activity in the oxidation of hydrogen (in the gaseous state in the presence of excess oxygen) has been studied for samples of Pt(Pd)/Ta₂O_5−x, formed by reduction with hydrogen. The samples obtained had greater activity than the traditional catalysts Pt(Pd)/Al₂O₃. According to X-ray diffraction analysis and electron microscopic studies, Ta₂O_5−x becomes amorphous with the formation of more reduced non-stoichiometric oxygen-deficient tantalum oxides with a surface layer of catalyst. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 44, No. 3, pp. 180–185, May–June, 2008.     

Studies on thermal decomposition and oxidation of CoSb<Subscript>3</Subscript>

Thermal durability of CoSb₃ in vacuum, helium and air was investigated over the temperature range of 20–850 °C. A scanning electron microscope (SEM) and X-ray powder diffraction technique were used to investigate the microstructure and to carry out the phase analysis of the degradation products. The analysis of a non-isothermal and isothermal decomposition and oxidation of the CoSb₃ powders and polycrystalline samples were performed using simultaneous TG/DTA technique. More detailed studies were carried out on the oxidation in the temperature range 400–600 °C. It was established that the decomposition products are CoSb₂ and a volatile antimony. In case of oxidation a complex three-layered scale is formed, consisting of CoSb₂O₄, CoSb₂O₆ and Sb₂O₄ layers. Both the decomposition and the oxidation kinetics are determined by a diffusion through the growing layers of products. The electrical resistivity and Seebeck coefficient measurements have been also performed on pure and oxidized samples, which showed a large influence of the oxidation on the electrical properties.     

Homogeneous catalytic fluoroalkylation of thiophenols,phenols and pyrrole by Freons BrCF<Subscript>2</Subscript>CF<Subscript>2</Subscript>Br and CF<Subscript>2</Subscript>ClCFCl<Subscript>2</Subscript>

The use of sulfur dioxide as an electron transfer mediator in the presence of nitrogen bases permits the rather selective fluoroalkylation of thiophenols, phenols, and pyrrole by Freons BrCF₂CF₂Br and CF₂ClCFCl₂ under mild conditions. In the case of thiophenols, the fluoroalkylation occurs to give polyfluoroalkyl aryl sulfides, while phenols and pyrrole are alkylated in the ring. Effects were found for the electronic structure of the substrates and basicity of the medium (pK_α of the pyridines) on the oxidation-reduction properties of the reagents and the efficiency of the reactions studied. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 43, No. 5, pp. 315–322, September–October, 2007.     

Effect of the preparation method on the catalytic performance of Ca<Subscript>3</Subscript>Co<Subscript>4</Subscript>O<Subscript>9</Subscript> for methane oxidation

The layered structure oxide Ca₃Co₄O₉ particle was synthesized by two routes of citrate sol–gel method. The structure, morphology and surface property of Ca₃Co₄O₉ was characterized by XRD, SEM and XPS, respectively. The catalytic activity of Ca₃Co₄O₉ for methane combustion was tested in a fixed bed quartz tubular microreactor. The catalysis results reveal that the catalytic activity is sensitive to the texture of Ca₃Co₄O₉ by different route. TG measures confirm that the small particle size of Ca₃Co₄O₉ favors the oxygen transformation on the surface, which can be ascribed the random distribution of the crystal axes in irregular Ca₃Co₄O₉ particle.     

Nitrite oxidation on RuO<Subscript>2</Subscript> electrodes

An electrochemical kinetic investigation of nitrite oxidation to nitrate on RuO₂ is discussed. The process is studied by cyclic voltammetry, steady-state measurements and potential step measurements. The overall oxidation reaction is a two-electron process where the first step involves a reversible charge transfer: NO₂⁻ ⇔ NO₂ + e⁻ The one-electron oxidation of nitrite yields adsorbed NO₂ which is further oxidized to adsorbed (NO₂)⁺ and subsequently desorbed via a chemical reaction. In the general case, fit of experimental data is obtained with adsorption described by a Temkin isotherm unless the electrode is pre-treated at a cathodic potential where the (NO₂)_ads is removed. This treatment lowers the degree of coverage by intermediates but not the nature of the slow step. Published in Russian in Elektrokhimiya, 2008, Vol. 44, No. 1, pp. 142–149. The text was submitted by the authors in English.