Experimental and numerical studies on interactions of a spherical flame with incident and reflected shocks

Observations are presented from experiments and calculations where a laminar spherical CH4/air flame is perturbed successively by incident and reflected shock waves. The experiments are performed in a standard shock tube arrangement, in which a high-speed shadowgraph imaging system is used to record evolutions of the flame. Numerical simulations are conducted by using second-order wave propagation algorithms, based on two-dimensional axisymmetric Navier-Stokes equations with detailed chemical reactions. Qualitative agreements are obtained between the experimental and numerical results. Under actions of incident shock waves, Richtmyer-Meshkov instability responsible for the flame deformation is induced in the flame, and the distoned flame takes a barrel shape. Then, under subsequent actions of the shock wave reflected from a planar wall, the flame takes an inclined non-symmetrical kidney shape in a symmetric cross section, which means a mushroom-like shape of the flame comes finally into being. The vorticity direction in the ring cap has been altered by the reflected shock＇s action, which makes the head of the mushroom-like flame extend quickly to the side wall.     

Near-wall imaging using toluene-based planar laser-induced fluorescence in shock tube flow

A quantitative thermometry technique, based on planar laser-induced fluorescence (PLIF), was applied to image temperature fields immediately next to walls in shock tube flows. Two types of near-wall flows were considered: the side wall thermal boundary layer behind an incident shock wave, and the end wall thermal layer behind a reflected shock wave. These thin layers are imaged with high spatial resolution (15μm/pixel) in conjunction with fused silica walls and near-UV bandpass filters to accurately measure fluorescence signal levels with minimal interferences from scatter and reflection at the wall surface. Nitrogen, hydrogen or argon gas were premixed with 1–12% toluene, the LIF tracer, and tested under various shock flow conditions. The measured pressures and temperatures ranged between 0.01 and 0.8 bar and 293 and 600 K, respectively. Temperature field measurements were found to be in good agreement with theoretical values calculated using 2-D laminar boundary layer and 1-D heat diffusion equations, respectively. In addition, PLIF images were taken at various time delays behind incident and reflected shock waves to observe the development of the side wall and end wall layers, respectively. The demonstrated diagnostic strategy can be used to accurately measure temperature to about 60 μm from the wall.     

Type of reflection of a near-wall shock wave in the process of diffraction from a square channel

The results of an experimental and numerical investigation of the process of diffraction of shock waves from a square channel at a ninety-degree convex corner are presented for various incident shock wave Mach numbers M₀ (1.4<M₀<7). The type of reflection of the near-wall fragment of the diffracting shock wave from the wall and the wave velocity are determined as functions of M₀, direction, and time. Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 1, pp. 145–151, January–February, 2000. The work was carried out with partial support from the Russian Foundation for Basic Research (project No. 96-02-16170a).     

Re-initiation phenomenon of gaseous detonation induced by shock reflection

The two-dimensional, time-dependent, reactive Navier–Stokes equations including the effects of viscosity, thermal conduction and molecular diffusion were solved to reveal the wave evolution and chemical dynamics involved in the re-initiation process. The computation was performed for hydrogen–oxygen–argon mixtures at the low initial pressure (8.00 kPa), using detailed chemical reaction model. The results show that, the decoupled leading shock reflects on the right wall of the vertical branch. High temperature and pressure behind the reflected shock induce the generation of hot spots and local explosion. Therefore, the re-initiation of gaseous detonation occurs. In the re-initiation area, there exist very high OH concentration and no H ₂ concentration. However, in front of reflected shock, there exist relatively high H ₂ concentration and no OH radicals. Additionally, the shock–flame interaction induces RM instability. This results in the fast mixing between hot reacted gas mixture and the relatively cold unreacted gas mixture and accelerates the chemical reactions. However, the shock–flame interaction contributes much less to the re-initiation, in contrast with shock reflection. The transition of leading shock from regular reflection to Mach reflection happens during the re-initiation. The computed evolution of wave structures involved in the re-initiation is qualitatively agreeable with that from the experimental schlieren images.      

Regular reflection of a shock wave from a solid wall in a stream of fuel mixture

The two-dimensional stationary problem of regular reflection of a shock wave from a plane solid wall in a fuel gas mixture is examined in the case when the mixture is ignited at the intersection of the incident wave with the wall and a flame front is formed behind the reflected shock wave. The shock waves and the flame front are considered plane surfaces of discontinuity. The fuel mixture and the reaction products are considered perfect, inviscid, and non-heat-conducting gases.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 4, pp. 161–163, July–August, 1978.     

Numerical investigation of ethylene flame bubble instability induced by shock waves

In this paper, the ethylene/oxygen/nitrogen premixed flame instabilities induced by incident and reflected shock wave were investigated numerically. The effects of grid resolutions and chemical mechanisms on the flame bubble deformation process are evaluated. In the computational frame, the 2D multi-component Navier–Stokes equations with second-order flux-difference splitting scheme were used; the stiff chemical source term was integrated using an implicit ordinary differential equations (ODEs) solver. The two ethylene/oxygen/nitrogen chemical mechanisms, namely 3-step reduced mechanism and 35-step elementary skeletal mechanism, were used to examine the reliability of chemistry. On the other hand, the different grid sizes, Δx × Δy = 0.25 × 0.5mm and Δx × Δy = 0.15 × 0.2mm, were implemented to examine the accuracy of the grid resolution. The computational results were qualitatively validated with experimental results of Thomas et al. (Combust Theory Model 5:573–594, 2001). Two chemical mechanisms and two grid resolutions used in present study can qualitatively reproduce the ethylene spherical flame instability process generated by an incident shock wave of Mach number 1.7. For the case of interaction between the flame and reflected shock waves, the 35-steps mechanism qualitatively predicts the physical process and is somewhat independent on the grid resolutions, while the 3-steps mechanism fails to reproduce the instability of ethylene flame for the two selected grid resolutions. It is concluded that the detailed chemical mechanism, which includes the chain elementary reactions of fuel combustion, describes the flame instability induced by shock wave, in spite of the fact that the flame thickness (reaction zone) is represented by 1–2 grids only.      

Reflection of a plane shock wave from a rigid concave wall

We present the results of an experimental study of the reflection of a plane stationary shock wave with Mach number in the range 1.21–1.35 from a rigid cylindrical concave wall. The experiments were carried out in a shock tube. In experimental shock tube technology the reflection of a shock wave from a rigid wall is often used for obtaining high temperatures [1]. This circumstance is associated with the fact that the temperature behind the reflected wave is significantly higher than that behind the incident wave.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 4, pp. 33–39, July–August, 1970.     

Reflection of shock waves from a solid boundary in a mixture of condensed materials. 1. Equilibrium approximation

The process of reflection of shock waves (SW) from a solid wall in a two-component mixture of condensed materials is studied within the framework of mechanics of heterogeneous media. The velocity of a reflected SW and the values of the parameters behind its front are analytically determined as functions of the velocity of the incident wave and the initial parameters of the mixture. It is shown that the absolute value of the velocity of the reflected SW can be greater than the velocity of the incident SW in mixtures with a small content of the light component and at low velocities of the incident shock wave. The nonmonotonic character of the dependence of pressure in the final equilibrium state behind the incident SW on the initial volume concentration of particles is demonstrated. The velocity of the incident SW is estimated for the case where a similar effect is also observed behind a reflected SW. It is established that, for weak shock waves, the dependence of the amplification factor of the reflected SW on the initial volume concentration of the light component is nonmonotonic and has a local maximum. It is noted that, as the velocity of the incident SW increases, the effect of compacting of the mixture (increase in concentration of the heavy component) behind the reflected SW becomes much less pronounced than in a passing SW. Institute of Theoretical and Applied Mechanics, Siberian Division, Russian Academy of Sciences. Novosibirsk 630090. Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 40, No. 5, pp. 73–78, September–October, 1999.     

Structure of compression shock waves in porous elastoplastic materials

The shock-wave structure in a porous elastoplastic material is studied. In a certain range of parameters, the existence of a four-wave structure of a compression shock wave is possible. Regimes in which a reflected shock wave does not appear at all have been found in the problem of shock-wave reflection from a rigid wall. In this case, the entire energy of the incident shock wave transforms to thermal energy due to dissipation induced by the viscous collapse of the pores. Institute of Theoretical and Applied Mechanics, Siberian Division, Russian Academy of Sciences, Novosibirsk 630090. Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 39, No. 6, pp. 27–32, November–December, 1998.     

激波诱导火焰变形、混合和燃烧的数值研究

为了深入研究激波诱导的火焰变形以及由此带来的混合和燃烧变化特性,采用带单步化学反应的Navier-Stokes方程和高网格分辨率,对平面入射激波及其反射激波诱导球形火焰变形的现象进行了二维数值研究,计算结果与实验结果较好吻合。研究结果显示,在反射激波作用前,火焰的变形和皱褶主要受入射激波诱导等物理过程影响;而在反射激波与失稳火焰作用后,燃烧放热率、火焰有效面积和界面长度均迅速增加,控制火焰变形的机制逐渐向化学反应(燃烧)过程过渡;在失稳火焰发展的后期,增强的燃烧过程能够削弱火焰界面的皱褶,进而抑制未燃气和可燃气的混合。由此可以得出结论,激波诱导的火焰界面通过变形可促进界面两侧未燃气与可燃气的混合,进而强化燃烧过程,但燃烧的增强却反过来能抑制混合;认识两者之间的关系有助于利用或控制激波 火焰相互作用过程。     

A numerical study of oblique shock wave reflections over wedges in an ideal quantum gas

The various oblique shock wave reflection patterns generated by a moving incident shock on a planar wedge using an ideal quantum gas model are numerically studied using a novel high resolution quantum kinetic flux splitting scheme. With different incident shock Mach numbers and wedge angles as flow parameters, four different types of reflection patterns, namely, the regular reflection, simple Mach reflection, complex Mach reflection and the double Mach reflection as in the classical gas can be classified and observed. Both Bose–Einstein and Fermi–Dirac gases are considered.      

Guderley reflection for higher Mach numbers in a standard shock tube

An experimental study shows that the Guderley reflection (GR) of shock waves can be produced in a standard shock tube. A new technique was utilised which comprises triple point of a developed weak Mach reflection undergoing a number of reflections off the ceiling and floor of the shock tube before arriving at the test section. Both simple perturbation sources and diverging ramps were used to generate a transverse wave in the tube which then becomes the weak reflected wave of the reflection pattern. Tests were conducted for three ramp angles (10°, 15°, and 20°) and two perturbation sources for a range of Mach numbers (1.10–1.40) and two shock tube expansion chamber lengths (2.0 and 4.0 m). It was found that the length of the Mach stem of the reflection pattern is the overall vertical distance traveled by the triple point. Images with equivalent Mach stem lengths in the order of 2.0 m were produced. All tests showed evidence of the fourth wave of the GR, namely the expansion wave behind the reflected shock wave. A shocklet terminating the expansion wave was also identified in a few cases mainly for incident wave Mach numbers of approximately 1.20.     

Regular reflection of a magnetohydrodynamic shock wave from a conducting wall

In two-dimensional supersonic gasdynamics, one of the classical steady-state problems, which include shock waves and other discontinuities, is the problem concerning the oblique reflection of a shock wave from a plane wall. It is well known [1–3] that two types of reflection are possible: regular and Mach. The problem concerning the regular reflection of a magnetohydrodynamic shock wave from an infinitely conducting plane wall is considered here within the scope of ideal magnetohydrodynamics [4]. It is supposed that the magnetic field, normal to the wall, is not equal to zero. The solution of the problem is constructed for incident waves of different types (fast and slow). It is found that, depending on the initial data, the solution can have a qualitatively different nature. In contrast from gasdynamics, the incident wave is reflected in the form of two waves, which can be centered rarefaction waves. A similar problem for the special case of the magnetic field parallel to the flow was considered earlier in [5, 6]. The normal component of the magnetic field at the wall was equated to zero, the solution was constructed only for the case of incidence of a fast shock wave, and the flow pattern is similar in form to that of gasdynamics. The solution of the problem concerning the reflection of a shock wave constructed in this paper is necessary for the interpretation of experiments in shock tubes [7–10].Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 3, pp. 102–109, May–June, 1977.The author thanks A. A. Barmin, A. G. Kulikovskii, and G. A. Lyubimov for useful discussion of the results obtained.     

The reflected pressure field in the interaction of weak shock waves with a compressible foam

This paper deals with the waves that are reflected from slabs of porous compressible foam attached to a rigid wall when impacted by a weak shock wave. The interest is in establishing possible attenuation of the pressure field after a shock or blast wave has struck the surface. Foam densities from 14 to 38 kg/m³ were tested over a range of shock wave Mach numbers less than 1.4. It is shown that the initial reflected shock wave strength is accurately predicted by the pseudo-gas model of Gelfand et al. (1983), with a pressure ratio of approximately 80% of the value for reflection off a rigid wall. Evidence is presented of gas entering the foam during the early stages of the process. A second wave emerges from the foam at a later stage and is separated from the first by a region of constant velocity and pressure. This second wave is not a shock wave but a compression front of significant thickness, which emerges from the foam earlier than predicted by the pseudo-gas model. Analysis of the origin of this wave points to much more complex flows within the foam than previously assumed, particularly in an apparent decrease in average wave front speed as the foam is compressed. It is shown that the pressure ratio across both these waves taken together is slightly higher than that for reflection off a rigid wall. In some cases this compression wave train is followed by a weak expansion wave.This article was processed using Springer-Verlag T_EX Shock Waves macro package 1990.     

Further analytical considerations of weak planar shock wave reflections over a concave wedge

A simplified analytical model of the Mach reflection of a planar shock wave over a concave cylindrical wedge has been used to predict the triple point trajectory and the triple point trajectory angle at glancing incidence.Comparison with experimental results suggests that the simplified approach for predicting the triple point trajectory is good for an incident shock wave Mach number, M_i, less than 1.1. However, the prediction of the triple point trajectory angle at glancing incidence is good for any value of M_i as long as the assumption of a perfect gas is valid.     

On flows behind shock waves reflected from a solid wall

The flow fields associated with the interaction of a normal shock wave with a plane wall kept at a constant temperature were studied based on kinetic theory which can describe appropriately the shock structure and its reflection process. With the use of a difference scheme, the time developments of the distributions of the fluid dynamic quantities (velocity, temperature, pressure and number density of the gas) were obtained numerically from the BGK model of the Boltzmann equation subject to the condition of diffusive-reflection at the wall for several cases of incident Mach number:M ₁=1.2, 1.5, 2.0, 3.0, 4.0, 5.0 and 6.0. The reflection process of the shocks is shown explicitly together with the resulting formation of the flow fields as time goes on. The nonzero uniform velocity toward the wall occurring between the viscous boundary layer and the reflected shock wave is found to be fairly large, the magnitude of which is of the order of several percent of the velocity induced behind the incident shock, decreasing as the incident Mach number increases. It is also seen that a region of positive velocity (away from the wall) within the viscous boundary layer manifests itself in the immediate vicinity of the wall, which is distinct for larger incident Mach numbers. Some of the calculated density profiles are compared with available experimental data and also with numerical results based on the Navier-Stokes equations. The agreement between the three results is fairly good except in the region close to the wall, where the difference in the conditions of these studies and the inappropriateness of the Navier-Stokes equations manifest themselves greatly in the gas behavior.This article was processed using Springer-Verlag TEX Shock Waves macro package 1990.     

The reflection of a shock wave over a cone

An investigation was made of the reflection of planar shock waves from cones. 86 cones, the half apex angle of which varied from 10° to 52° at every 0.5°, were installed in a 60 mm×150 mm diaphragmless shock tube equipped with holographic interferometry. The diaphragmless shock tube had a high degree of reproducibility with which the scatter of shock wave Mach number was within ±0.25% for shock wave Mach number ranging from 1.16 to approximately 2.0. The reflection of shock waves over cones was visualized using double exposure holographic interferometry. Whitham's geometrical shock wave dynamics was used to analyse the motion of Mach stems over cones. It is found that for relatively smaller apex angles of cones trajectory angles of resulting irregular reflections coincide with the so-called glancing incidence angles and their Mach stems appear to be continuously curved from its intersection point with the incident shock wave, which shows the chractericstic of von Neumann reflection. The domain of the existence of the von Neumann reflection was analytically obtained and was found to be broadened much more widely than that of two-dimensional reflections of shock waves over wedges.     

Gas content factor in the interaction of shock waves of different intensity in a two-phase gas-liquid medium

The transition from regular to Mach interaction is investigated in connection with the interaction of two plane weak or moderate shock waves of different intensity in a two-phase gas-liquid medium over the entire range of gas contents. A nonmonotonic dependence of the transition limit and the flow parameters on the gas content is detected. The investigation extends the results of [1] corresponding to the reflection of a shock wave from a wall. At intermediate gas contents in the case of opposing shock waves, analogous to the normal reflection of a shock wave from a solid wall, the results are in agreement with [2]. In the case of weak shock waves non-linear asymptotic expansions [3] are employed. In the extreme cases of single-phase media the results coincide with the findings of [3, 4]. Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 172–174, November–December, 1986.     

A holographic interferometric study of shock wave focusing in a circular reflector

A holographic interferometric study was made of the focusing of reflected shock waves from a circular reflector. A diaphragmless shock tube was used for incident shock Mach numbers ranging from 1.03 to 1.74. Hence, the process of reflected shock wave focusing was quantitatively observed. It is found that a converging shock wave along the curved wall undergoes an unsteady evolution of mach reflection and its focusing is, therefore, subject to the evolution of the process of shock wave reflections. The collision of triple points terminates the focusing process at the geometrical focus. In order to interprete quantitatively these interferograms, a numerical simulation using an Eulerian solver combined with adaptive unstructured grids was carried out. It is found numerically that the highest density appears immediately after the triple point collision. This implies that the final stage of focusing is mainly determined by the interaction between shock waves and vortices. The interaction of finite strength shock waves, hence, prevents a curved shock wave from creating the infinite increase of density or pressure at a focal point which is otherwise predicted by the linear acoustic theory.     

Interaction of a high-speed combustion front with a closely packed bed of spheres

The head-on collision of a combustion front with a closely packed bed of ceramic-oxide spheres was investigated in a vertical 76.2 mm diameter tube containing a nitrogen diluted stoichiometric ethylene–oxygen mixture. A layer of spherical beads in the diameter range of 3–12.7 mm was placed at the bottom of the tube and a flame was ignited at the top endplate. Four orifice plates spaced at one tube diameter were placed at the ignition end of the tube in order to accelerate the flame to either a “fast-flame” or a detonation wave before the bead layer face. The mixture reactivity was adjusted by varying the initial mixture pressure between 10 and 100 kPa absolute. The pressure before and within the bead layer was measured by flush wall-mounted pressure transducers. For initial pressures where a fast-flame interacts with the bead layer peak pressures recorded at the bead layer face were as high as five times the reflected Chapman–Jouget detonation pressure. The explosion resulting from the interaction developed by two distinct mechanisms; one due to the shock reflection off the bead layer face, and the other due to shock transmission and mixing of burned and unburned gas inside the bead layer. The measured explosion delay time (time after shock reflection from the bead layer face) was found to be independent of the incident shock velocity. As a result, the explosion initiation is not the direct result of the shock reflection process but instead is more likely due to the interaction of the reflected shock wave and the trailing flame. The bead layer was found to be very effective in attenuating the explosion front transmitted through the bead layer and thus isolating the tube endplate. This paper is based on work that was presented at the 21th International Colloquium on the Dynamics of Explosions and Reactive Systems, Poitiers, France, July 23–27, 2007.