Molecularly imprinted solid‐phase extraction coupled with ultra high performance liquid chromatography and fluorescence detection for the determination of estrogens and their metabolites in wastewater

Estrogens are an important class of endocrine‐disrupting compounds, and their contamination of environmental waters through the effluents of wastewater treatment plants could have an important impact on aquatic biota, even at low concentrations. For this reason, the development of selective and sensitive extraction methodologies, which permit the identification and quantification of these compounds at trace level concentrations, is very important. In this study, a quantitative method based on molecularly imprinted solid phase extraction coupled to ultra high performance liquid chromatography with fluorescence detection has been developed. It has been used for the simultaneous determination of three estrogens and two of their metabolites in water samples from wastewater treatment plants. The method developed presents satisfactory limits of detection (between 0.18 and 0.45 ng·mL^?1), good recoveries (higher than 60%) and low relative standard deviations (under 10%). The method was used to analyze wastewater from a veterinary hospital as well as influent and effluent samples of a wastewater treatment plant of Gran Canaria (Spain) The concentrations of the detected hormones ranged from 1.35 to 2.57 ng·mL^?1.     

Natural estrogens in dairy products: Determination of free and conjugated forms by ultra high performance liquid chromatography with tandem mass spectrometry

Natural estrogens are synthesized by mammals in different amounts depending on the developmental stage and pregnancy/lactation period, and they may pass into milk, where they are mostly present as glucuronated and sulfated forms. In modern dairy practices, about 75% of milk is produced from pregnant cows; therefore, the amount of hormones that may pass into milk could be of concern. While estrogen determination in milk has been investigated in depth, the individual determination of estrogens and their conjugated forms in dairy products has not been fully addressed. The aim of this work was to develop and assess a sensitive method, using the peculiar retention properties of graphitized carbon black, to extract natural free estrogens and their major conjugated metabolites, without any enzymatic cleavage, from yogurt, cheese, and butter. The free and conjugated estrogens were eluted in two distinct fractions from the solid‐phase extraction cartridge and analyzed separately by ultra high performance liquid chromatography coupled to tandem mass spectrometry. Recoveries were higher than 80% for all the three sample typologies. The highest matrix effects were observed for butter, which was richest in lipid content, but was below 30%. A survey on some commercial dairy products suggests that production processes decreased estrogen content.     

Determination of estrogens and bisphenol A in bovine milk by automated on-line C30 solid-phase extraction coupled with high-performance liquid chromatography–mass spectrometry

Using triacontyl bonded silica (C₃₀) as on-line solid-phase extraction (SPE) material and a specially designed on-line analytical system which allowed large sample volume injection, a high speed and robust on-line SPE-HPLC–MS method was established for the analysis of five estrogens and bisphenol A (BPA) in milk samples. The milk sample is pretreated with acetonitrile for protein precipitation and then treated with primary secondary amine for the removal of polar impurities in the matrix. Then the pretreated sample can be automatically loaded by a LC pump. For effective extraction, an offshoot with NH₄Ac solution of high-flow rate was employed to dilute the loaded sample by a mixing tee before sample was loaded onto the C₃₀ extraction column. In this way, large volume injection (1 mL in this experiment) could be achieved. Some important parameters such as sample loading flow rate, sample dilution ratio and injection volume were optimized. Under the optimized conditions, the recoveries for all analytes range from 71.4 to 97.1% and reproducibility represented as RSDs are less than 15.0% (n = 5) with milk samples spiked at 0.6 and 15 ng/mL of each analyte. To the authors’ knowledge, it constitutes the first work describing a C₃₀ on-line SPE-LC–MS analytical method for the screen and monitoring of these estrogens and BPA in milk.     

Determination of pharmaceuticals in wastewaters using solid-phase extraction-liquid chromatography-tandem mass spectrometry

Four different commercial sorbents for solid-phase extraction have been evaluated for the extraction of a group of acidic pharmaceuticals in terms of selectivity and capacity: Oasis hydrophilic-lipophilic balance (HLB), Oasis MAX (strong anion exchange), Oasis WAX (weak anion exchange) and a commercial available molecularly imprinted polymer specific for non-steroidal anti-inflammatory drugs. Among the sorbents studied, molecularly imprinted polymer proved to be very effective in the reduction of matrix interferences and the selective extraction of acidic pharmaceuticals, such as salicylic acid, ibuprofen, fenoprofen, diclofenac and naproxen, among others, from effluent wastewater samples. Moreover, molecularly imprinted solid-phase extraction protocol was applied to liquid chromatography coupled to tandem mass spectrometry (MS/MS) with the purpose of evaluating the clean-up effect on ion suppression/enhancement when the complexity of the samples increases and a reduction of this effect was observed. Molecularly imprinted solid-phase extraction followed by liquid chromatography coupled to ultraviolet detection and liquid chromatography coupled to tandem mass spectrometry validation methodologies with effluent wastewaters were developed, obtaining recoveries between 70 and 85% and limits of detection at low levels of μg/L (0.15-1 μg/L) and ng/L (0.5-2 ng/L), respectively. The final application of molecularly imprinted solid-phase extraction and liquid chromatography coupled to MS/MS detection showed the presence of acidic pharmaceuticals studied in this work in effluent wastewaters (相似文献   

Determination of tricyclic antidepressants in human plasma using pipette tip solid-phase extraction and gas chromatography-mass spectrometry

A method for the simultaneous extraction of four tricyclic antidepressants from human plasma samples using pipette tip SPE with MonoTip C(18) tips is presented. Human plasma (0.1 mL) containing four tricyclic antidepressants (amitriptyline, amoxapine, imipramine, and trimipramine) and an internal standard (IS), protriptyline, was mixed with 0.4 mL of distilled water and 100 microL 1 M NaOH solution. After centrifugation of the mixture, the supernatant was extracted to the C(18) phase of the tip by 20 repeated aspirating/dispensing cycles using a manual micropipettor. The analytes retained in the tip were eluted with methanol by five repeated aspirating/dispensing cycles. Without evaporation and reconstitution, the eluate was directly injected into a gas chromatograph injector and detected by a mass spectrometer with SIM in the positive-ion electron impact mode. Recovery of the four antidepressants and IS spiked into human plasma was 80.2-92.1%. The regression equations for the four antidepressants showed excellent linearity in the range of 0.2-40 ng/0.1 mL. LODs and LOQs for the four drugs were 0.05-0.2 ng/0.1 mL and 0.2-0.5 ng/0.1 mL, respectively. Intra- and interday CVs for the four drugs in plasma were no greater than 9.5%.     

Determination of avoparcin in animal tissues and milk using LC‐ESI‐MS/MS and tandem‐SPE

A highly sensitive and selective method using LC‐ESI‐MS/MS and tandem‐SPE was developed to detect trace amounts of avoparcin (AV) antibiotics in animal tissues and milk. Data acquisition using MS/MS was achieved by applying multiple reaction monitoring of the product ions of [M + 3H]³⁺ and the major product ions of AV‐α and ‐β at m/z 637 → 86/113/130 and m/z 649 → 86/113/130 in ESI(+) mode. The calculated instrumental LODs were 3 ng/mL. The sample preparation was described that the extraction using 5% TFA and the tandem‐SPE with an ion‐exchange (SAX) and InertSep C18‐A cartridge clean‐up enable us to determine AV in samples. Ion suppression was decreased by concentration rates of each sample solution. These SPE concentration levels could be used to detect quantities of 5 ppb (milk), 10 ppb (beef), and 25 ppb (chicken muscle and liver). The matrix matching calibration graphs obtained for both AV‐α (r >0.996) and ‐β (r >0.998) from animal tissues and milk were linear over the calibration ranges. AV recovery from samples was higher than 73.3% and the RSD was less than 12.0% (n = 5).     

Simultaneous determination of a selected group of cytostatic drugs in water using high-performance liquid chromatography-triple-quadrupole mass spectrometry

In recent years, an increasing concern has risen about the presence of pharmaceuticals in the aquatic environment. Despite their toxicity, increasing consumption and release into the municipal sewage, only a few studies have been focused on cytostatic drugs, mainly due to the lack of methods for their simultaneous analysis. In this work, a method, based on solid-phase extraction prior to high-performance liquid chromatography-triple quadrupole mass spectrometry determination, was optimized and validated for the simultaneous determination of some (14) of the most widely used cytostatic drugs in river water, influent and effluent wastewater. Process efficiency was in the range between 41 and 99% in real samples, except for cytarabine (24%), docetaxel (17%) and methotrexate (30%), due to suppression effects; precision values were <11%, except for gemcitabine (up to 19%); and detection limits were in the range between 0.1 and 38 ng/L. Cytarabine, doxorubicin, etoposide, gemcitabine, iphosphamide and vinorelbine were found at concentration levels up to 14 ng/L in influent and effluent wastewater, showing an insignificant decrease during sewage treatment; cytarabine and gemcitabine were found in effluent wastewater and were also detected in river water associated with effluent discharges.     

Determination of estrogens in wastewater using three-phase hollow fiber-mediated liquid-phase microextraction followed by HPLC

Three-phase hollow fiber-mediated liquid-phase microextraction followed by HPLC was used for the determination of three synthetic estrogens, namely diethylstilbestrol, dienestrol, and hexestrol, in wastewater. Extraction conditions including organic solvent, volume ratio between donor solution and acceptor phase, extraction time, stirring rate, donor phase and acceptor phase were optimized. The target compounds were extracted from a 10 mL aqueous sample at pH 1.5 (donor solution) through a 45 mm in length hollow polypropylene fiber that was immersed in 1-octanol in advance, and then the hollow fiber was filled with 10 microL 0.5 mol/L sodium hydroxide solution (acceptor phase). After a 40 min extraction, the acceptor phase was directly injected into an HPLC system for detection. Under the optimized extraction conditions, a large enrichment factor (more than 300-fold) was achieved for the three estrogens. The determination limit at an S/N of 3 ranged from 0.25 to 0.5 microg/L for the estrogens. The recovery ratio was more than 86% in the determination of these estrogens in wastewater.     

Simultaneous determination of four trace estrogens in feces,leachate, tap and groundwater using solid–liquid extraction/auto solid‐phase extraction and high‐performance liquid chromatography with fluorescence detection

A simple and selective high‐performance liquid chromatography method coupled with fluorescence detection was developed for the simultaneous measurement of trace levels of four estrogens (estrone, estradiol, estriol and 17α‐ethynyl estradiol) in environmental matrices. For feces samples, solid–liquid extraction was applied with a 1:1 v/v mixture of acetonitrile and ethyl acetate as the extraction solvent. For liquid samples (e.g., leachate and groundwater), hydrophobic/lipophilic balanced automated solid‐phase extraction disks were selected due to their high recoveries compared to conventional C₁₈ disks. Chromatographic separations were performed on a reversed‐phase C₁₈ column gradient‐eluted with a 45:55 v/v mixture of acetonitrile and water. The detection limits were down to 1.1 × 10^?2 (estrone), 4.11 × 10^?4 (estradiol), 5.2 × 10^?3 (estriol) and 7.18 × 10^?3 μg/L (17α‐ethynyl estradiol) at excitation/emission wavelengths of 288/310 nm, with recoveries in the range of 96.9 ± 3.2–105.4 ± 3.2% (n = 3). The method was successfully applied to determine estrogens in feces and water samples collected at livestock farms and a major river in Northeast China. We observed relatively high abundance and widespread distribution of all four estrogens in our sample collections, implying the urgency for a comprehensive and intricate investigation of estrogenic fate and contamination in our researched area.     

Determination of Acrolein‐Derived 3‐Hydroxypropylmercapturic Acid in Human Urine Using Solid‐phase Extraction Combined with Molecularly Imprinted Mesoporous Silica and LC‐MS/MS Detection

A novel method for the analysis of (3‐hydroxypropyl)mercapturic acid (HPMA), a major acrolein metabolite in human urine incorporating a molecularly imprinted solid‐phase extraction (MISPE) process using N‐acetylcysteine ‐imprinted mesoporous silica particles coupled with LC‐MS/MS detection was developed. The molecularly imprinted mesoporous silica particles were synthesized based on the supported material of ordered mesoporous silica SBA‐15 with N‐acetylcysteine (NAC) as template using surface molecular imprinting technology. The condition of MISPE procedures was optimized. The use of MISPE improved the accuracy and precision of the LC‐MS method and lowered the limit of detection (0.23 ng/mL). The recoveries at three spiked levels ranged between 88.5% to 108.6%. The developed MISPE method enabled the selective extraction of HPMA successfully in human urine and could be used as an effective approach for the determination of ultra‐trace HPMA in complex biological matrices. The results in real samples showed that median levels of HPMA were significantly higher (1922.0 ng/mg of creatinine, N = 75) in smokers than in nonsmokers (759.1 ng/mg of creatinine, N = 5), demonstrating the higher acrolein uptake in smokers than in nonsmokers.     

Multi-residue method for the analysis of synthetic surfactants and their degradation metabolites in aquatic systems by liquid chromatography-time-of-flight-mass spectrometry

Synthetic surfactants are economically important chemicals, as they are widely used in household cleaning detergents, textiles, paints, polymers and personal care products. In this work we have developed a method capable of the isolation and analysis of the most widely used surfactants (linear alkylbenzene sulfonates, LAS, nonylphenol ethoxylates, NPEO, and alcohol ethoxylates, AEO) and their main degradation products (sulfophenyl carboxylic acids, SPC, nonylphenol ethoxycarboxylates, NPEC, and polyethylene glycols, PEG) in aqueous and solid environmental matrices. First, analytes were extracted by ultrasonic extraction from sediments and suspended solids using methanol at 50°C as solvent and 3 cycles (30 min per cycle). Clean-up and pre-concentration of the extracts and water samples were carried out by solid-phase extraction (SPE), using Oasis HLB cartridges. Recoveries were generally about 80% for most compounds. Identification and quantification of target compounds were performed by liquid chromatography-time-of-flight-mass spectrometry (LC-ToF-MS), which has been much less used in the field of environmental analysis than other MS techniques. Examples which illustrate the possible advantages of this technique for multi-analyte analysis of target and non-target contaminants in environmental samples are provided. Finally, the methodology developed here was validated by measuring the concentration of surfactants and their metabolites in selected marine sediment and seawater samples collected in Long Island Sound (NY), and in influent and effluent wastewater from Stony Brook treatment plant (NY). This paper presents some of the first data relative to the occurrence of PEG in the environment, especially in sediments where concentrations were generally higher (up to 1490 μg/kg) than those for other classes of targeted surfactants and their metabolites.     

Isolation and determination of estrogens in water samples by solid‐phase extraction using molecularly imprinted polymers and HPLC

Advanced SPE with molecularly imprinted polymers (MIP) was used in this study. A noncovalent imprinting approach was applied to separate 17β‐estradiol, estriol, and estrone from water samples. Polymer material was prepared by bulk polymerization with methacrylic acid as a functional monomer, divinylbenzene and ethyleneglycol dimethacrylate as crosslinkers, and acetonitrile, acetonitrile/toluene (3:1, v/v) or isooctane/toluene (1:99, v/v) as a porogen. We also prepared an MIP film on a silica gel surface with methacrylic acid and ethyleneglycol dimethacrylate as monomers and acetonitrile as a solvent. Qualitative and quantitative hormone analyses were carried out by HPLC with various detection techniques, including UV/visible spectroscopic detection (diode array detection) and electrochemical detection (CoulArray). The results of the study indicate that MIP technology is an excellent method for the quality control of estrogens in environmental analyses with a low quantification limit for 17β‐estradiol of around 26 (diode array detection) and 0.25 ng/mL (electrochemical detection). The proposed method was found to be suitable for routine determinations of the analyzed compound in environmental laboratories.     

Determination of haloacetic acids in water using layered double hydroxides as a sorbent in dispersive solid‐phase extraction followed by liquid chromatography with tandem mass spectrometry

In the present study, highly efficient and simple dispersive solid‐phase extraction procedure for the determination of haloacetic acids in water samples has been established. Three different types of layered double hydroxides were synthesized and used as a sorbent in dispersive solid‐phase extraction. Due to the interesting behavior of layered double hydroxides in an acidic medium (pH?4), the analyte elution step was not needed; the layered double hydroxides are simply dissolved in acid immediately after extraction to release the analytes which are then directly introduced into a liquid chromatography with tandem mass spectrometry system for analysis. Several dispersive solid‐phase extraction parameters were optimized to increase the extraction efficiency of haloacetic acids such as temperature, extraction time and pH. Under optimum conditions, good linearity was achieved over the concentration range of 0.05–100 μg/L with detection limits in the range of 0.006–0.05 μg/L. The relative standard deviations were 0.33–3.64% (n = 6). The proposed method was applied to different water samples collected from a drinking water plant to determine the concentrations of haloacetic acids.     

Multiresidue determination of UV filters in water samples by solid‐phase extraction and liquid chromatography with tandem mass spectrometry analysis

UV filters, contained in sunscreens and other cosmetic products, as well as in some plastics and industrial products, are nowadays considered contaminants of emerging concern because their widespread and increasing use has lead to their presence in the environment. Furthermore, some UV filters are suspected to have endocrine disruption activity. In the present work, we developed an analytical method based on liquid chromatography with tandem mass spectrometry for the determination of UV filters in tap and lake waters. Sixteen UV filters were extracted from water samples by solid‐phase extraction employing graphitized carbon black as adsorbent material. Handling 200 mL of water sample, satisfactory recoveries were obtained for almost all the analytes. The limits of detection and quantification of the method were comparable to those reported in other works, and ranged between 0.7–3.5 and 1.9–11.8 ng/L, respectively; however in our case the number of investigated compounds was larger. The major encountered problem in method development was to identify the background contamination sources and reduce their contribution. UV filters were not detected in tap water samples, whereas the analyses conducted on samples collected from three different lakes showed that the swimming areas are most subject to UV filter contamination.     

Determination of organophosphate esters in water samples by mixed‐mode liquid chromatography and tandem mass spectrometry

A simple and sensitive method for the determination of organophosphate esters in water samples by mixed‐mode liquid chromatography with electrospray ionization tandem mass spectrometry coupled with solid‐phase extraction is developed. Using seven alkyl phosphates, three chlorinated alkyl phosphates, and four aryl phosphates as the targets, the developed method was systematically evaluated on the basis of the influence of the solid‐phase extraction cartridge, eluting solvent, sample‐loading volume, mobile phase condition, and the separation of reversed‐phase chromatography and mixed‐mode liquid chromatography. Under the optimal conditions, these organophosphate esters can be extracted by ENVI‐18 cartridge, eluted by 6 mL of 25% dichloromethane in acetonitrile, and then qualified and quantified by mixed‐mode liquid chromatography with tandem mass spectrometry in the multiple reaction‐monitoring mode. The application of mixed‐mode liquid chromatography endows the separation with reasonable retention for both hydrophilic and hydrophobic organophosphate esters regardless of their polarity, which is hardly achieved by reversed‐phase chromatography. Good linearity (from 0.9877 to 0.9969), low quantification limits (1–35 ng/L after extraction of 100 mL of river water), and acceptable recovery rates (58.6–116.2%, with the relative standard deviation <18.0%) were obtained. Finally, the established method was used for analyzing surface water samples, and the good applicability of this method was demonstrated.     

Solid‐phase extraction of perfluoroalkylated compounds from sea water

This study describes an in‐depth investigation of the parameters involved in the solid‐phase extraction performance of perfluoroalkylated compounds (seven carboxylates and one sulfonate), particularly with sea water samples. The two most popular sorbents, Oasis WAX and Oasis HLB, were considered and it was observed that the high ionic strength of sea water may impair solid‐phase extraction recoveries. In the final protocol, Oasis HLB cartridges were selected, incorporating a 10% methanol clean‐up step before elution with methanol, since less matrix effects were obtained. The proposed method allows successful recoveries, higher than 71%, and relative standard deviations lower than 20%. It also provides excellent limits of detection values between 0.01 and 0.21 ng/L. Finally, the method was applied to fresh and sea water samples, where several perfluoroalkylated compounds were found at concentrations ranging between 0.16 and 64 ng/L. In the case of perfluorooctane sulfonate, recently included in the Water Frame Directive, its concentration reached the highest values among the perfluoroalkylated compounds measured (64 ng/L in river samples).     

Simultaneous determination of benzodiazepines and their metabolites in human serum by liquid chromatography-tandem mass spectrometry using a high-resolution octadecyl silica column compatible with aqueous compounds

A liquid chromatography-tandem mass spectrometry (LC-MS/MS) method using a high-resolution octadecyl silica column compatible with aqueous compounds was developed for the simultaneous determination of benzodiazepines and their metabolites in human serum. This method enabled us to determine multiple benzodiazepines, including flurazepam, bromazepam, chlordiazepoxide, nitrazepam, clonazepam, flunitrazepam, estazolam, clobazam, lorazepam, alprazolam, triazolam, brotizolam, fludiazepam, diazepam, quazepam, prazepam and their metabolites such as 7-aminonitrazepam, 7-aminoclonazepam, 7-acetamidonitrazepam, N-desmethylclobazam and N-desmethyldiazepam. The analytes spiked into human serum were subjected to solid-phase extraction followed by liquid chromatography coupled with electrospray ionization tandem mass spectrometry. The running time was within 25 min for the measurement of 22 benzodiazepines and their metabolites. The recovery rates exceeded 58.1% for those compounds except for quazepam, which showed a recovery of 45.8%. The limit of detection ranged from 0.3 to 11.4 ng/mL. Linearity was satisfactory for all compounds. These data suggest that the present method can be applicable to routine assay for benzodiazepines in the clinical setting.     

Determination of diphenylether herbicides in water samples by solid-phase microextraction coupled to liquid chromatography

Solid-phase microextraction (SPME) coupled to LC for the analysis of five diphenylether herbicides (aclonifen, bifenox, fluoroglycofen-ethyl, oxyfluorfen, and lactofen) is described. Various parameters of extraction of analytes onto the fiber (such as type of fiber, extraction time and temperature, pH, impact of salt and organic solute) and desorption from the fiber in the desorption chamber prior to separation (such as type and composition of desorption solvent, desorption mode, soaking time, and flush-out time) were studied and optimized. Four commercially available SPME fibers were studied. PDMS/divinylbenzene (PDMS/DVB, 60 microm) and carbowax/ templated resin (CW/TPR, 50 microm) fibers were selected due to better extraction efficiencies. Repeatability (RSD, < 7%), correlation coefficient (> 0.994), and detection limit (0.33-1.74 and 0.22-1.94 ng/mL, respectively, for PDMS/DVB and CW/TPR) were investigated. Relative recovery (81-104% for PDMS/DVB and 83-100% for CW/TPR fiber) values have also been calculated. The developed method was successfully applied to the analysis of river water and water collected from a vegetable garden.     

SPE–HPLC–MS/MS method for the trace analysis of tobacco‐specific N‐nitrosamines and 4‐(methylnitrosamino)‐1‐(3‐pyridyl)‐1‐butanol in rabbit plasma using tetraazacalix[2]arene[2]triazine‐modified silica as a sorbent

Tobacco‐specific N‐nitrosamines (TSNAs), including N′‐nitrosonornicotine, 4‐(methylnitrosamino)‐1‐(3‐pyridyl)‐1‐butanone, N′‐nitrosoanatabine, and N′‐nitrosoanabasine, have been implicated as a source of carcinogenicity in tobacco and cigarette smoke. We present a rapid and effective method comprising SPE based on tetraazacalix[2]arene[2]triazine‐modified silica as sorbent and analysis with HPLC–MS/MS for the determination of TSNAs and 4‐(methylnitrosamino)‐1‐(3‐pyridyl)‐1‐butanol (NNAL), a metabolite of 4‐(methylnitrosamino)‐1‐(3‐pyridyl)‐1‐butanone, in rabbit plasma. The linear dynamic ranges were 10–2000 pg/mL for NNAL and 4–2000 pg/mL for the four TSNAs with good correlation coefficients (>0.9965). The LODs were in the range of 0.9–3.7 pg/mL, and the LOQs were between 2.9 and 12.3 pg/mL. The accuracies of the method were also evaluated and found to be in the range of 90.1–113.3%. This method is promising to be applied to the preconcentration and determination of TSNAs and NNAL in smoke and human body fluids.     

Determination of anatoxin-a in environmental water samples by solid-phase microextraction and gas chromatography-mass spectrometry

In the present work, a method was developed and optimized aiming at the determination of anatoxin-a in environmental water samples. The method is based on the direct derivatization of the analyte by adding hexylchloroformate in the alkalinized sample (pH = 9.0). The derivatized anatoxin-a was extracted by a solid-phase microextraction (SPME) procedure, submersing a PDMS fiber in an amber vial for 20 min under magnetic stirring. GC-MS was used to identify and quantify the analyte in the SIM mode. Norcocaine was used as internal standard. The following ions were chosen for SIM analyses (quantification ions in italics): anatoxin-a: 191, 164, 293 and norcocaine: 195, 136, 168. The calibration curve showed linearity in the range of 2.5-200 ng/mL and the LOD was 2 ng/mL. This method of SPME and GC-MS analysis can be readily utilized to monitor anatoxin-a for water quality control.