新型混合离子-电子导体Sm0.9Ca0.1Al1-xMnxO3-δ的制备及其电性能研究

采用有机凝胶法结合固相烧结技术制备了单相的Sm0.9Ca0.1Al1-xMnxO3-δ(SCAM, x=0.1-0.5)新型混合离子-电子导体.通过TG-DTA,XRD和直流四引线法研究了凝胶前驱体的热分解和相转化过程、烧结体的结构、相稳定性、导电性能及其电输运机理.结果表明,凝胶前驱体在900℃焙烧5h可以形成完全晶化的四方钙钛矿相纳米粉体,SCAM陶瓷样品在还原气氛下的相稳定性随Mn含量的升高而降低.经高温烧结制得的SCAM陶瓷的总电导率取决于p型电导,其值随Mn含量和温度的升高而增大,导电行为符合p型小极化子跳跃机理. 随烧结温度的升高或保温时间的延长,SCAM9155的电导率和相对密度先增大后减小,1600℃烧结10h的SCAM9155样品具有最高的电导率和相对密度(98.2%),该样品在空气和5%H2/Ar气氛中850℃时的电导率分别为7.30和1.91eV.具有较高电导率的Ca,Mn掺杂的SmAlO3有望成为一种新型的SOFC阳极材料.     

双掺杂的Sm0.9Sr0.1Al1-xCoxO3-δ钙钛矿结构导电陶瓷的制备及其电性能

采用有机凝胶法结合高温烧结制备了Sm_0.9Sr_0.1Al_1-xCo_xO_3-δ (SSAC,x = 0.2,0.4,0.5,0.6) 系列钙钛矿结构混合导电陶瓷,并详细讨论了烧结温度和Co掺杂量对其晶体结构、相组成和电性能的影响.X射线衍射结果显示,过高的烧结温度或Co掺杂量都会导致杂相Sm(Sr)CoO₃生成,Co在该体系的固溶限位于50mol%—60mol%之间,Co对Al的部分取代使晶格体积增大.电性能测量结果表明,SSAC陶瓷的电导率主要取决于p型电导,其导电行为符合小极化子跳跃导电机制;随着烧结温度的升高,材料的电导率逐渐增大;在固溶限内随Co含量的增加,SSAC陶瓷的电导率增大,表观活化能减小;1200 ℃烧结10 h制得的单相Sm_0.9Sr_0.1Al_0.5Co_0.5O_3-δ陶瓷体在800℃的电导率达63.4 S/cm,表观活化能为0.14eV.具有良好电性能的SSAC导电陶瓷有望应用于高温电化学领域. 关键词： 导电陶瓷 3')" href="#">Sr和Co掺杂的SmAlO₃ 有机凝胶法 电性能     

Sm0.9Sr0.1AlO3-δ钙钛矿氧化物的固相反应合成和电学性能

用固相反应法制备了Sm_0.9Sr_0.1AlO_3-δ钙钛矿氧化物陶瓷.通过XRD,SEM和交流复阻抗谱以及氧浓差电池方法研究了样品的物相结构、微观形貌、电学性能及输运机理.结果表明,在1650℃烧结时,可以制备出单相的具有四方钙钛矿结构的氧化物Sm_0.9Sr_0.1AlO_3-δ;1650℃烧结16 h时的Sm_0.9Sr_0.1AlO_3-δ样品具有最高的相对密度和电导率,其值分别为96.7%和1.3×10^-2S/cm(900℃),比未掺杂的SmAlO₃的电导率大4个数量级左右,高温区电导活化能(T>670℃)小于低温区电导活化能(T<670℃);Sm_0.9Sr_0.1AlO_3-δ在空气气氛中是一个氧离子和电子空穴的混合导体,氧离子迁移数在0.7左右,并随温度升高逐渐增加,氧离子电导活化能(0.95eV)大于空穴电导活化能(0.84eV),900℃时氧离子电导率为9.65×10^-3S/cm. 关键词： 3')" href="#">SmAlO₃ 氧离子导电性 混合导体 活化能     

Sm0.9Sr0.1AlO3-δ钙钛矿氧化物的固相反应合成和电学性能

用固相反应法制备了Sm0.9Sr0.1AlO3-δ钙钛矿氧化物陶瓷.通过XRD,SEM和交流复阻抗谱以及氧浓差电池方法研究了样品的物相结构、微观形貌、电学性能及输运机理.结果表明,在1650℃烧结时,可以制备出单相的具有四方钙钛矿结构的氧化物Sm0.9Sr0.1AlO3-δ;1650℃烧结16 h时的Sm0.9Sr0.1AlO3-δ样品具有最高的相对密度和电导率,其值分别为96.7%和1.3×10-2S/cm(900℃),比未掺杂的SmAlO3的电导率大4个数量级左右,高温区电导活化能(T＞670℃)小于低温区电导活化能(T＜670℃);Sm0.9Sr0.1AlO3-δ在空气气氛中是一个氧离子和电子空穴的混合导体,氧离子迁移数在0.7左右,并随温度升高逐渐增加,氧离子电导活化能(0.95 eV)大于空穴电导活化能(0.84 eV),900℃时氧离子电导率为9.65×10-3S/cm.     

钙钛矿型中温固体氧化物燃料电池阴极Ba0.5Sr0.5Al0.1Fe0.9O3-δ

研究一种新型不含钴的钙钛矿型中温固体氧化物燃料电池阴极Ba_0.5Sr_0.5Al_0.1Fe_0.9O_3-δ (BSAF)材料的晶体结构、电导率以及在对称电池中的电极极化性能. 研究发现,BSAF阴极在空气中低于450 oC表现出典型的具有正温度系数的半导体行为,最高电导率达到14 S/cm;在450-750 oC,却表现出负温度系数,且电导率在750 oC下降到6 S/cm. 电化学研究表明,在基于混合离子导体的对称电池中,BSAF阴极在650-700 oC表现出良好的电极极化性能.以3%H₂O/H₂为燃料和空气为氧化剂,单电池在700 oC的开路电压和最大功率输出分别达到420 mW/cm².     

钙钛矿型氧离子导体KNb1-xMgxO3-δ的制备和表征

在高温高压（4.0GPa，870℃）下合成了具有正交钙钛矿结构的KNb_1-xMg_x O_3-δ（x=0.0—0.3）系列固体电解质，并系统地研究了Mg掺杂对其结构相变和导电性的影响.变温拉曼谱和DTA测量结果表明，随着温度的升高，KNb_{1-xMgxO3-δ发生了结构相变，由铁电正交、四方相转变为顺 电立方相.由于Mg掺杂削弱了B位离子对自发极化的贡献以及A位离子与BO关键词： 钙钛矿 离子电导 1-xMgxO3-δ')" href="#">KNb1-xMgxO3-δ 高温高压 铁电相变}     

Bi1-xLaxFeO3±δ薄膜的快速制备及铁电性

样品的制备是对影响样品质量的各个工艺参数进行优化的过程. 传统的试错法是对各个参数逐个进行尝试, 需要的周期较长. 与传统的单参数尝试法相比, 高通量样品制备方法可以对参数实现并行筛选, 因而极大地缩短了优化工艺所需的时间. 本工作借助高通量制备方法成功实现系列镧掺杂BiFeO₃薄膜的快速优化, 包括对烧结温度、镧元素含量和高温固态反应气氛等关键工艺参数的快速筛选, 同时分析了不同生长条件下样品的结构并测试了其铁电性. 实验结果表明: 1) 560 ℃ 烧结可得到单相薄膜; 2)测量不同La含量样品的铁电性, 发现当E=75 kV/cm时, La=15%的样品剩余极化值(2Pr)最大, 约为26.7 μC/cm²; 3) 在纯氧气氛下烧结有助于得到结晶性更好的单相Bi_0.75La_0.25FeO_3±δ 薄膜, 并且能够提高薄膜的铁电性.     

窄带隙KNb1-xFexO3-δ的室温铁磁性

We have investigated the structure, optical and magnetic properties of ferroelectric KNb_1-xFexO_3-δ (X=0, 0.01, 0.03, 0.05, 0.10, 0.15, 0.20, 0.25) synthesized by a traditional solid-state reaction method. According to the X-ray diffraction and the results of Rietveld refinement, all the samples maintain orthorhombic distorted perovskite structures with Amm2 space group without any secondary phase, suggesting the well incorporation of Fe ions into the KNbO₃ matrix. With the increase of Fe concentration, the band gap of each sample is decreased gradually, which is much smaller than the 3.18 eV band gap of pure KNbO₃. Through X-ray photoelectron spectrum analysis, the increased density of oxygen vacancy and Fe ions may be responsible for the observed decrease in band gap. Compared with the pure KNbO₃, Fe doped samples exhibit room-temperature weak ferromagnetism. The ferromagnetism in KNb_1-xFexO_3-δ with low-concentration dopants (X=0.01-0.10) can be attributed to the bound magnetic polaron mediated exchange. The enhancement of magnetism for the high-concentration (X=0.10-0.20) doped samples may arise from the further increase of magnetic Fe ions.     

Sr掺杂钙钛矿型氧化物Y1-xSrxCoO3的溶胶-凝胶制备及电阻率温度关系研究

采用溶胶-凝胶方法成功制备了Sr的替代化合物Y_1-xSr_xCoO₃ (x=0, 0.01, 0.05, 0.10, 0.15, 0.20), 系统地研究了20–720 K温度范围内Y_1-xSr_xCoO₃的电阻率温度关系. 研究表明, 随着Sr的替代含量的增加, Y_1-xSr_xCoO₃的电阻率迅速地降低, 这主要是由于载流子浓度的增加引起. 样品x=0和0.01在低于330和260 K的温度范围内, 电阻率与温度之间满足指数关系lnρ∝1/T, 获得导电激活能分别为0.2950和0.1461 eV. 然而, 实验显示lnρ∝1/T关系仅成立于重掺杂样品的高温区; 在低温区莫特定律lnρ∝T^-1/4成立, 且表明重掺杂引入势垒, 导致大量局域态的形成. 根据莫特T^-1/4定律拟合实验数据, 评估了局域态密度N(E_F), 它随着掺杂量的增加而增加. 关键词： 热电材料 溶胶-凝胶 3')" href="#">YCoO₃     

PrBa2Cu3O7-δ的制备和电子结构

采用固相反应法制备了正交单相PrBa₂Cu₃O_7-δ样品.运用标准直流四引线法测量了该样品的电阻,发现它随温度的变化呈半导体行为.通过XPS测量表明,样品中明显合有Pr⁴⁺.最后从能带结构讨论了PtBa₂Cu₃0_7-δ不超导的原因. 关键词：     

双掺杂BaxAgyCa3-x-yCo4O9氧化物的织构与电输运性能

采用柠檬酸溶胶凝胶和放电等离子烧结制备了Ca位双掺杂型的Ba_xAg_yCa_3-x-yCo₄O₉烧结体,利用X射线衍射仪、扫描电子显微镜、电阻率测试仪等研究了烧结体相组成、取向度、织构及电性能.结果表明：含Ag的掺杂试样中出现了偏离化学计量比分布的Ag单质,掺杂试样取向度随Ba与Ag掺杂量之比x/y的增大而提高,含Ag的掺杂试样取向度低于未掺杂试样,不含Ag的掺杂试样取向度高于未掺杂试样.x=y=01的试样导电机理发生变化.Ba,Ag掺杂量相等的试样保持较低取向度的同时具有较低的电阻率,在973 K时达到最低值（73 mΩcm）,而取向度最低的Ag单掺杂试样电阻率在所有试样中最低,在973 K时为63 mΩcm. 关键词： 3Co₄O₉')" href="#">Ca₃Co₄O₉ 双掺杂 织构 电输运性能     

La0.1Bi0.9-xEuxFeO3化合物的结构与性能研究

利用固相反应烧结技术制备La_0.1Bi_0.9-xEu_xFeO₃系列化合物. 利用X射线粉末衍射进行物相鉴定和结构分析,确定了材料的相关系：x≤0.05,材料为R3c结构相;0.08≤x≤0.12,材料为赝R3c结构相;x≥0.15是Pbnm相,其中0.15≤x≤0.20区域Pbnm相存在畸变. 磁测量结果表明,材料具有弱铁磁性,对于x≤0.20材料,磁矩在x=0.12成分存在极值. 利用阻抗分析仪测量了室温介电常数随成分的变化关系.讨论了材料的结构与弱铁磁性和室温介电常数间的关系. 关键词： 0.1Bi_0.9-xEu_xFeO₃')" href="#">La_0.1Bi_0.9-xEu_xFeO₃ X射线衍射 磁性 介电常数     

CaCu3Ti4O12陶瓷的微观结构和电学性能

利用传统的固相反应工艺，在不同的烧结温度下制备了一系列的CaCu₃Ti₄O₁₂陶瓷样品，考察了其微观结构以及介电和复阻抗方面的电学性质.研究发现这些样品在微观结构方面可分为三种类型，高介电性与微观结构有着密切的关联性.室温下，样品的低频介电常数随陶瓷晶粒尺寸的增大而提高.随着测试温度的升高，不同微观结构类型的样品呈现出不同的电学性质的变化，但其中也存在着一些相同的特征.高温下，介电频谱呈现出一个低频介电响应和两个类Debye型弛豫色散，复阻抗谱呈现出三个Cole-Cole半圆弧.将实验上观测到的电学性质的起因归于陶瓷多晶微结构中的晶畴、晶界和晶粒内的缺陷. 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 微观结构 电学性质     

Synthesis and electrical properties of In2O3(ZnO)m superlattice nanobelt

One-dimensional（ID） In₂O₃（ZnO）_m superlattice nanobelts are synthesized by a chemical vapor deposition method.The formation of the In₂O₃（ZnO）_m superlattice is verified by the high-resolution transmission electron microscopy images.The typical zigzag boundaries could be clearly observed.An additional peak at 614 cm^-1 is found in the Raman spectrum,which may correspond to the superlattice structure.The study about the electrical transport properties reveals that the In₂O₃（ZnO）_m nanobelts exhibit peculiar nonlinear I-V characteristics even under the Ohmic contact measurement condition,which are different from the Ohmic behaviors of the In-doped ZnO nanobelts.The photoelectrical measurements show the differences in the photocurrent property between them,and their transport mechanisms are also discussed.     

Resistive switching in ceramic multiferroic Bi0.9Ca0.1FeO3

We report resistive switching effects in polycrystalline samples of the multiferroic Bi_0.9Ca_0.1FeO₃ with silver electrodes. Mössbauer spectroscopy shows that upon Ca-doping the Fe remains in a 3+ valence state, suggesting charge compensation through the creation of large amounts of oxygen vacancies. Electrical characterization shows that the oxide/metal resistance can be switched between high and low resistance states by applying voltage pulses. This process was shown to be forming free and a strong relaxation after switching was found. We rationalize our results by considering oxygen vacancies migration to and from the metal–oxide interface, resulting in variations of the Schottky potential barrier height that modulate the interface resistance.     

Magnetic properties of Nd0.9Dy0.1Fe3(BO3)4

The magnetic properties of trigonal Nd_0.9Dy_0.1Fe₃(BO₃)₄ substituted compound with the competitive Nd-Fe and Dy-Fe exchange interactions have been investigated. It has been shown that in Nd_0.9Dy_0.1Fe₃(BO₃)₄ a spontaneous spin-reorientation transition from an ease-axis state to an easy-plane occurs near 8 K. Anomalies of the magnetization curves are observed in a spin-flop transition induced by the magnetic field B‖c. The calculations were performed using a molecular-field approximation and a crystal-field model for the rare-earth subsystem. Extensive experimental data on the magnetic properties of Nd_0.9Dy_0.1Fe₃(BO₃)₄ have been interpreted and good agreement between theory and experiment has been achieved using the obtained theoretical dependences.     

Preparation, structure and ferromagnetic properties of the nanocrystalline Ti1-xMnxO2 thin films grown by radio frequency magnetron co-sputtering

This paper reported that the Mn-doped TiO2 films were prepared by radio frequency （RF） magnetron cosputtering. X-ray diffraction measurements indicate that the samples are easy to form the futile structure, and the sizes of the crystal grains grow big and big as the Mn concentration increases. X-ray photoemlssion spectroscopy measurements and high resolution transmission electron microscope photographs confirm that the manganese ions have been effectively doped into the TiO2 crystal when the Mn concentration is lower than 21%. The magnetic property measurements show that the Ti1-xMnxO2 （x = 0.21） films are ferromagnetic at room temperature, and the saturation magnetization, coercivity, and saturation field are 16.0 emu/cm^3, 167.5 × 80 A/m and 3740 × 80 A/m at room temperature, respectively. The room-temperature ferromagnetism of the films can be attributed to the new futile Ti1-xMnxO2 structure formed by the substitution of Mn^4＋ for Ti^4＋ into the TiO2 crystal .lattice, and could be explained by O vacancy （Vo）-enhanced ferromagnetism model.     

X-ray photoelectron spectroscopic investigations on cubic BaTiO3, BaTi0.9Fe0.1O3 and Ba0.9Nd0.1TiO3 systems

X-ray photoelectron spectroscopic (XPS) studies were carried out on wet-chemically synthesized cubic BaTiO₃, Ba_0.9Nd_0.1TiO₃ and BaTi_0.9Fe_0.1O_3−δ powders. The compounds were prepared by hydrothermal and gel to crystallite conversion technique; and phases formed readily at 420 K. The phase purity of the powders was confirmed from X-ray diffractometry. Chemical state and chemical environment of the constituent elements in the compositions were examined by XPS. Ba²⁺ was found to exist in two different chemical environments in these titanates. The Ti 2p_3/2 photoelectron peak in BaTi_0.9Fe_0.1O_3−δ was found to be broadened after Fe³⁺ substitution. Any resolvable broadening was not observed distinctly in the Ti 2p peak for Ba_0.9Nd_0.1TiO₃, unsintered BaTiO₃ and BaTiO₃ annealed in hydrogen (8% H₂ + Ar) at 1000 K. The prevalence of mixed-valent titanium and iron in BaTi_0.9Fe_0.1O_3−δ composition was evident from the XPS results and was further supported by the enhanced electrical conductivity at 298-550 K for BaTi_0.9Fe_0.1O_3−δ in comparison to BaTiO₃ and Ba_0.9Nd_0.1TiO₃. Hydroxyl incorporation was facilitated by substituting Nd³⁺ in Ba-sublattice. The presence of hydroxyls was observed from the broadening of the O 1s peak in XPS studies of the compounds.     

La0.9Sr0.1MnO3薄膜中电流效应研究

用直流磁控溅射法在(100)LaAlO₃衬底上制备了La_0.9Sr_0.1MnO₃薄膜.经退火处理后薄膜的原子力显微镜形貌观测和X射线衍射分析显示具有比较好的质量.电阻率-温度关系表明La_0.9Sr_0.1MnO₃薄膜在281 K处发生金属绝缘体转变.电流在0.01—4 mA范围内，薄膜的峰值电阻率随电流增大而减小，在4 mA下获得了30.5%的峰值电阻率变 关键词： 掺杂锰氧化合物 0.9Sr_0.1MnO₃薄膜')" href="#">La_0.9Sr_0.1MnO₃薄膜 电流诱导效应 相分离理论