Unstrained, modulation-doped, In0.3Ga0.7As/In0.29Al0.71As field-effect transistor grown on GaAssubstrate

The fabrication, structure, and properties of unstrained modulation-doped, 1-μm-long and 10-μm-wide gate, field effect transistors made of In_0.3Ga_0.7As/In_0.29As_0.71As heterojunctions grown on GaAs substrates using compositionally step-graded buffer layers are described. These devices have a transconductance of 335 mS/mm, f_max of 56 GHz, and a gate breakdown voltage of 23.5 V     

Enhanced device performance by unstrainedIn0.3Ga0.7As/In0.29Al0.71Asdoped-channel FET on GaAs substrates

An alternative In_0.3Ga_0.7As/In_0.29Al_0.71As heterostructure based on GaAs is proposed, which provides a large conduction-band discontinuity for a better carrier confinement, resulting in a high-carrier density. This unstrained high-In channel achieved a better device performance, as compared with the conventional pseudomorphic channel, which is always limited by the critical thickness. This unstrained channel is also proven to be more stable after a long-term biased-stress     

Metamorphic In0.4Al0.6As/In0.4Ga0.6As HEMTs on GaAs substrate

New In_0.4Al_0.6As/In_0.4Ga_0.6 As metamorphic (MM) high electron mobility transistors (HEMTs) have been successfully fabricated on GaAs substrate with T-shaped gate lengths varying from 0.1 to 0.25 μm. The Schottky characteristics are a forward turn-on voltage of 0.7 V and a gate breakdown voltage of -10.5 V. These new MM-HEMTs exhibit typical drain currents of 600 mA/mm and extrinsic transconductance superior to 720 mS/mm. An extrinsic current cutoff frequency f_T of 195 GHz is achieved with the 0.1-μm gate length device. These results are the first reported for In_0.4 Al_0.6As/In_0.4Ga_0.6As MM-HEMTs on GaAs substrate     

Influence of quantum-well width on device performance ofAl0.30Ga0.70As/In0.25Ga0.75As (on GaAs) MODFETs

An experimental study in which the quantum well width (W) is varied from 45 to 200 Å is discussed. Optimum device performance was observed at a well width of 120 Å. The 0.2-μm×130-μm devices with 120-Å quantum-well width typically exhibit a maximum channel current density of 550 mA/mm, peak transconductance of 550 mS/mm, and peak current gain cutoff frequency ( f_T) of 122 GHz. These results have been further improved in subsequent fabrications employing a trilevel-resist mushroom-gate process. The 0.2-μm×50-μm devices with mushroom gate exhibit a peak transconductance of 640 mS/mm, peak f _T of 100 GHz, and best power gains cutoff frequency in excess of 200 GHz. These results are among the best ever reported for GaAs-based FETs and are attributed to the high two-dimensional electron gas (2DEG) sheet density, good low-field mobility, low ohmic contact, and the optimized mushroom gate process     

Double-dopedIn0.35Al0.65As/In0.35Ga0.65As power heterojunction FET on GaAs substrate with 1 W outputpower

A double-doped metamorphic In_0.35Al_0.65As/In _0.35Ga_0.65As power heterojunction FET (HJFET) on GaAs substrate is demonstrated. The HJFET exhibits good dc characteristics, with gate forward turn on voltage of 1.0 V, breakdown voltage of 20 V, and maximum drain current of 490 mA/mm. Under RF operation at a frequency of 950 MHz, a power added efficiency of 63% with associated output power of 31.7 dBm is obtained at a gate width of 12.8 mm. This large gate width and state-of-the-art power performance in metamorphic HJFETS were enabled by a selective etching, sputtered WSi gate process and low surface roughness due to an Al_0.60Ga_0.40As_0.69Sb_0.31 strain relief buffer     

In0.52Al0.48As/In0.53Ga0.47As MSM photodetectors and HEMT's grown by MOCVD on GaAs substrates

The authors report the first demonstration of In_0.52Al _0.48As/In_0.53Ga_0.47As metal-semiconductor-metal (MSM) photodetectors and high-electron-mobility transistors (HEMTs) grown on GaAs substrates by organometallic chemical vapor deposition. Both photodetectors and transistors showed no degradation in performance compared to devices simultaneously grown on InP substrates. The photodetectors exhibited a responsivity of 0.45 A/W and leakage current of 10 to 50 nA. The HEMTs with a gate length of 1.0 μm showed a transconductance as high as 250 mS/mm, and f_T and f_max of 25 and 70 GHz, respectively     

In0.52Al0.48As/In0.53Ga0.47As double-heterojunction p-n-p bipolar transistors grown bymolecular beam epitaxy

P-n-p In_0.52Al_0.48As/In_0.53Ga_0.47 As double-heterojunction bipolar transistors with a p⁺-InAs emitter cap layer grown by molecular-beam epitaxy have been realized and tested. A five-period 15-Å-thick In_0.53Ga_0.47As/InAs superlattice was incorporated between the In_0.53Ga_0.47As and InAs cap layer to smooth out the valence-band discontinuity. Specific contact resistance of 1×10^-5 and 2×10^-6 Ω-cm² were measured for nonalloyed emitter and base contacts, respectively. A maximum common emitter current gain of 70 has been measured for a 1500-Å-thick base transistor at a collector current density of 1.2×10³ A/cm². Typical current gains of devices with 50×50-μm² emitter areas were around 50 with ideality factors of 1.4     

In0.53Ga0.47As/In0.52Al0.48As雪崩光电二极管的数值模拟研究

建立了SACM型In0.53Ga0.47As/In0.52Al0.48As雪崩光电二极管(APD)的分析模型,通过数值研究和理论分析设计出高性能的In0.53Ga0.47As/In0.52Al0.48As APD。器件设计中,一方面添加了In0.52Al0.48As势垒层来阻挡接触层的少数载流子的扩散,进而减小暗电流的产生;另一方面,雪崩倍增区采用双层掺杂结构设计,优化了器件倍增区的电场梯度分布。最后,利用ATLAS软件较系统地研究并分析了雪崩倍增层、电荷层以及吸收层的掺杂水平和厚度对器件电场分布、击穿电压、IV特性和直流增益的影响。优化后APD的单位增益可以达到0.9 A/W,在工作电压(0.9 Vb)下增益为23.4,工作暗电流也仅是纳安级别(@0.9 Vb)。由于In0.52Al0.48As材料的电子与空穴的碰撞离化率比InP材料的差异更大,因此器件的噪声因子也较低。     

High-performance In0.52Al0.48As/In0.53Ga0.47As HFET compatible with optical-detectorintegration

The authors report the successful demonstration of a 1.0-μm gate InAlAs/InGaAs heterojunction FET (HFET) on top of thick InGaAs layers using lattice-matched molecular beam epitaxy (MBE). This scheme is compatible with metal-semiconductor-metal (MSM) photodetector fabrication. The authors measured the performance of InAlAs/InGaAs HFETs from 0 to 40 GHz. Device performance is characterized by peak extrinsic transconductances of 390 mS/mm and as-measured cutoff frequencies up to 30 GHz for a nominal 1.0-μm-gate-length HFET. HFET device measurements are compared for samples growth with and without the thick underlying InGaAs optical-detector absorbing layer     

120nm栅长In0.7Ga0.3As/In0.52Al0.48As HEMTs 器件

利用新型的PMMA/PMGI/ZEP520/PMGI四层胶T形栅电子束光刻技术制备出120nm栅长InP基雁配In0.7Ga0.3As/In0.52Al0.48As 高电子迁移率晶体管。制作出的InP基HEMT器件获得了良好的直流和高频性能,跨导、饱和漏电流密度、阈值电压、电流增益截止频率和最大单向功率增益频率分别达到520 mS/mm, 446 mA/mm, -1.0 V, 141 GHz 及 120 GHz。文中的材料结构和所有器件制备均为本研究小组自主研究开发。     

Self-alignedIn0.52Al0.48As/In0.53Ga0.47As heterojunction bipolar transistors with graded interface onsemi-insulating InP grown by molecular beam epitaxy

A self aligned In_0.52Al_0.48As/In_0.53 Ga_0.47As double heterojunction bipolar transistor (HBT) with a graded heterointerface has been grown by molecular-beam epitaxy (MBE) and tested. The DC characteristics of HBT structures with a compositionally graded junction using a linear graded In_0.53Ga_0.47-xAl_xAs between two ternary layers were investigated. Typical quaternary graded devices with an emitter dimension of 50×50 μm² exhibited a current gain as high as 1260, as compared to 800 for abrupt devices, at a collector current density of 2.8×10³ A/cm²     

Buried-Pt gate InP/In0.52Al0.48As/In0.7Ga0.3As pseudomorphic HEMTs

InP-based high electron mobility transistors (HEMTs) were fabricated by depositing Pt-based multilayer metallization on top of a 6-nm-thick InP etch stop layer and then applying a post-annealing process. The performances of the fabricated 55-nm-gate HEMTs before and after the post-annealing were characterized and were compared to investigate the effect of the penetration of Pt through the very thin InP etch stop layer. After annealing at 250 °C for 5 min, the extrinsic transconductance (G_m) was increased from 1.05 to 1.17 S/mm and Schottky barrier height was increased from 0.63 to 0.66 eV. The unity current gain cutoff frequency (f_T) was increased from 351 to 408 GHz, and the maximum oscillation frequency (f_max) was increased from 225 to 260 GHz. These performance improvements can be attributed to penetration of the Pt through the 6-nm thick InP layer, and making contact on the InAlAs layer. The STEM image of the annealed device clearly shows that the Pt atoms contacted the InAlAs layer after penetrating through the InP layer.     

InP/In0.53Ga0.47As heterojunction bipolartransistors with a carbon-doped base grown by MOCVD

InP/In_0.53Ga_0.47As heterojunction bipolar transistors (HBTs) utilizing a carbon-doped base have been demonstrated. The devices were grown by low-pressure metalorganic chemical vapor deposition (LP-MOCVD) using carbon tetrachloride (CCl₄) as the p-type dopant source. These devices exhibit a DC common-emitter current gain of 50 and an emitter-base junction ideality factor of 1.29 in a structure for which no undoped spacer layer was employed at the emitter-base junction. These preliminary results suggest that C-doping of In_0.53Ga_0.47As may be a suitable alternative to Zn in MOCVD-grown InP/In_0.53Ga_0.47As HBTs     

Fabrication of 80-nm T-gate high indium In0.7Ga0.3As/In0.6Ga0.4As composite channels mHEMT on GaAs substrate with simple technological process

An 80-nm gate length metamorphic high electron mobility transistor (mHEMT) on a GaAs substrate with high indium composite compound-channels In_0.7Ga_0.3As/In_0.6Ga_0.4As and an optimized grade buffer scheme is presented. High 2-DEG Hall mobility values of 10200 cm²/(V· s) and a sheet density of 3.5 × 10¹² cm^-2 at 300 K have been achieved. The device's T-shaped gate was made by utilizing a simple three layers electron beam resist, instead of employing a passivation layer for the T-share gate, which is beneficial to decreasing parasitic capacitance and parasitic resistance of the gate and simplifying the device manufacturing process. The ohmic contact resistance R_c is 0.2 Ω ·mm when using the same metal system with the gate (Pt/Ti/Pt/Au), which reduces the manufacturing cycle of the device. The mHEMT device demonstrates excellent DC and RF characteristics. The peak extrinsic transconductance of 1.1 S/mm and the maximum drain current density of 0.86 A/mm are obtained. The unity current gain cut-off frequency (f_T) and the maximum oscillation frequency (f_max) are 246 and 301 GHz, respectively.     

MetamorphicIn0.53Ga0.47As/In0.52Al0.48As HEMTs on germanium substrates

We report for the first time the successful epitaxial growth and processing of high-performance metamorphic high electron mobility transistors (HEMTs) on Ge substrates, with a transconductance of 700 mS/mm and a saturation channel current of 650 mA/mm. To reduce parasitic capacitances due to the conductive substrate, a dry etch method based on CF₄ and O₂ reactive ion etching (RIE) is developed for selective substrate removal. Devices with 0.2 μm gate length display an increase of the extrinsic cut-off frequency f_T from 45 GHz before, to 75 GHz after substrate removal, whereas the maximum oscillation frequency f_max increases from 68 GHz to 95 GHz. Based on this excellent rf performance level, in combination with the highly selective thinning process, we think that Ge as a sacrificial substrate is a promising candidate for the integration of thinned individual HEMTs with passive circuitry on low-cost substrates. This could result in low-cost advanced hybrid systems for mass-market millimeter wave applications     

Characterization of surface-undoped In0.52Al0.48As/In0.53Ga0.47As/InP high electron mobilitytransistors

High-performance 0.3-μm-gate-length surface-undoped In_0.52 Al_0.48As/In_0.53Ga_0.47As/InP high-electron-mobility transistors (HEMTs) grown by molecular beam epitaxy (MBE) have been characterized and compared with a surface-doped structure. At 18 GHz, the surface-undoped HEMT has achieved a maximum stable gain (MSG) of 19.2 dB compared to 16.0 dB for the surface-doped structure. The higher MSG value of the surface-undoped HEMTs is obtained due to the improved g_m/g₀ ratio associated with the surface-induced electric field spreading effect. Comparison of identical 0.3-×150-μm-gate devices fabricated on surface-undoped and -doped structures has shown greatly improved gate leakage characteristics and much lower output conductance for the surface-undoped structure. It is demonstrated that the surface potential, modulated by different surface layer designs, affects the charge control in the conducting channel, especially the carrier injection into the buffer, resulting in excess output conductance. Several millimeter-wave coplanar waveguide (CPW) monolithic distributed amplifiers have been successfully fabricated by using the surface-undoped HEMT structure. A high gain per stage distributed amplifier with 170-dB±1-dB small-signal gain across a frequency band of 24-40 GHz, a W-band monolithic integrated circuit with 6.4-dB gain at 94 GHz, and a broad bandwidth distributed amplifier with 5-dB gain across a frequency band of 5 to 100 GHz have been demonstrated by using the surface-undoped structures     

Long-wavelength In0.53Ga0.47As metamorphicp-i-n photodiodes on GaAs substrates

Metamorphic In_0.53Ga_0.47As p-i-n photodiodes on GaAs substrate exhibiting the lowest dark current ever reported were fabricated and characterized. Their dark current, DC and RF performances were measured and compared for devices of different sizes. Typical dark current for 15-μm-diameter devices was 600 pA under 5-V reverse bias, corresponding to a dark current density of 3.40×10^-4 A/cm². Typical responsivity measured with 1.55-μm optical radiation was 0.55 A/W corresponding to an external quantum efficiency of 44%. The electrical 3 dB bandwidths of the photodiodes with diameters smaller than 20 μm were over 20 GHz     

Novel In0.52Al0.48As/In0.53Ga0.47As metamorphic high electron mobility transistors on GaAs substrate with InxGa1−xP graded buffer layers

Compositionally graded In_xGa_1−xP (x=0.48→x=1) metamorphic layers have been grown on GaAs substrate by solid source molecular beam epitaxy using a valved phosphorus cracker cell. Three series of samples were grown to optimize the growth temperature, V/III ratio and grading rate of the buffer layer. X-ray diffraction (XRD) and photoluminescence (PL) were used to characterize the samples. The following results have been obtained: (1) XRD measurement shows that all the samples are nearly fully strain relaxed and the strain relaxation ratio is about 96%; (2) the full-width at half-maximum (FWHM) of the XRD peak shows that the sample grown at 480°C offers better material quality; (3) the grading rate does not influence the FWHM of XRD and PL results; (4) adjustment of the V/III ratio from 10 to 20 improves the FWHM of XRD peak, and the linewidth of PL peak is close to the data obtained for the lattice-matched sample on InP substrate. The optimization of growth conditions will benefit the metamorphic HEMTs grown on GaAs using graded InGaP as buffer layers.     

Impact of surface layer on In0.52Al0.48As/In0.53Ga0.47As/InP high electron mobilitytransistors

The surface potential of FETs has shown a strong effect on the channel potential and charge control in the channel. A study of the role of undoped versus doped cap layers in In_0.52Al_0.48As-In_0.53Ga_0.47 As-InP high-electron-mobility transistors (HEMT) is discussed. As the result of surface potential effect, direct comparison of 0.3×150-μm² gate devices yielded improved gate breakdown characteristics and a DC output conductance of less than 15 mS/mm for the surface undoped structure compared to 50 mS/mm for the doped structure. The surface undoped MEMT achieved a very high maximum stable gain of 19.2 dB compared to 16.0 dB for the surface doped HEMT at 18 GHz, largely due to the improved g_m/g ₀ ratio. This study demonstrates that control of the surface potential in In_0.52Al_0.48As-In_0.53Ga _0.47As-InP HEMTs is consistent with the effect of a gate recess in MESFETs. This study also shows that, in achieving high-gain applications of HEMTs, the surface potential near the gate edge should be optimized through unconventional surface layer design     

Fabrication of In0.25Ga0.75As/InGaAsPstrained SQW lasers on In0.05Ga0.95As ternarysubstrate

A uniform In_0.05Ga_0.95As ternary substrate was grown by using liquid encapsulated Czochralski (LEC) technique with a method of supplying GaAs source material at a constant temperature, and InGaAs/InGaAsP strained single quantum well (SQW) lasers were fabricated on the substrate for the first time. The lasers lased at 1.03 μm and exhibited low threshold current density of 222 A/cm² and excellent characteristic temperature of 221 K, showing that the ternary substrate has a sufficient quality for laser fabrication