In-fiber polarizer based on a long-period fiber grating written on photonic crystal fiber

A novel in-fiber polarizer based on a long-period fiber grating (LPFG) is written by using a focused CO2 laser beam to notch a photonic crystal fiber periodically. Such a polarizer exhibits a high polarization extinction ratio of more than 20 dB over a wide wavelength range of ~11 nm near 1550 nm and a very low temperature sensitivity of 3.9 pm/ degrees C, which overcomes the disadvantages of the temperature sensitivity of other in-fiber polarizers created on conventional single-mode fiber.     

Long-period fiber gratings with variable coupling for real-time sensing applications

We demonstrate a long-period grating whose resonance varies in strength but remains fixed in wavelength with either temperature or strain. Using this fiber-grating sensor, we resolved a change of 1 muepsilon of strain or 0.04 degrees C in temperature. Such sensors require no spectrometer or other frequency-selective components and can operate in real time.     

Fiber Bragg grating sensor for simultaneous measurement of displacement and temperature

A new approach to measuring displacement and temperature simultaneously by use of a specially designed isosceles triangular cantilevered beam as a strain agent is demonstrated. A fiber Bragg grating epoxied onto the beam surface is experimentally demonstrated to have a temperature sensitivity of ~0.113 nm/ degrees C below 60 degrees C and a displacement sensitivity of 9.24x10(-2) nm/mm .     

Temperature sensitivity of Ge-B-SiO(2) waveguide Bragg gratings on a crystallized glass substrate

Waveguide Bragg gratings were fabricated by plasma-enhanced chemical-vapor deposition followed by irradiation with KrF excimer laser light through a phase mask. The period of the Bragg grating was 0.53 mum, and the Bragg wavelength was ~1.53 mum . The temperature dependence of the Bragg wavelength was 11 pm/ degrees C for a 10GeO(2) -90SiO(2)(mol.%) core waveguide on a Si substrate, and the Bragg wavelength shift was successfully reduced to 5.0pm/ degrees C by use of a 14GeO(2)-12B(2)O(3)-74SiO(2) (mol.%) core and a crystallized glass substrate with a thermal-expansion coefficient of -2.0x10(-6)(/ degrees C) .     

Simultaneous measurement of axial strain, temperature, and transverse load by a superstructure fiber grating

A novel and simple fiber-optic sensor based on a superstructure fiber grating for simultaneous measurement of temperature, axial strain, and transverse load is proposed and demonstrated. By measurement of the shift and split of broadband and narrow-band loss peaks, one can determine the temperature, axial strain, and transverse load simultaneously over the ranges 0-140 degrees , 0-1200muepsilon, and 0-0.3 kg/mm, respectively.     

Measurement of refractive-index variation with temperature by use of long-period fiber gratings

The thermo-optic coefficient of the core material of a fiber is analyzed by use of a pair of long-period fiber gratings. First the effective index difference between the core and the cladding modes is measured from the peaks of the interference fringe generated by the grating pair. The order of the cladding mode is decided by the cutoff wavelength and the numerical aperture of the fiber. The material index of the fiber core is obtained in terms of wavelength. At each wavelength the index is chosen to minimize the difference between the measured and the calculated spectra of the grating pair. Finally the thermo-optic coefficient of the fiber core is calculated by repetition of the measurement at different temperatures. With a germanosilicate-core fiber and a boron codoped germanosilicate-core fiber, the thermo-optic coefficients were 1.1x10(-5)/( degrees )C and 0.75x10(-5)/( degrees )C, respectively.     

基于长周期光纤光栅嵌入型Sagnac环光谱的折射率测量

将长周期光纤光栅(LPG)和光纤Sagnac环相结合,实现了折射率和温度的同时测量.首先利用二氧化碳激光器在保偏光纤上制作了长周期光纤光栅(PM-LPG),然后把该PM-LPG和普通单模光纤耦合器组成Sagnac环,作为传感单元.实验选择其某一透射峰作为测试对象,其波长随温度变化,强度随折射率变化,因此可实现两个参量的...     

Wide-passband, temperature-insensitive, and compact pi-phase-shifted long-period gratings in endlessly single-mode photonic crystal fiber

We demonstrate what is believed to be the first fabrication of a wide-passband, temperature-insensitive, and compact spectral filter based on a pi-phase-shifted long-period grating in an endless single-mode photonic crystal fiber. By introducing a pi-phase shift in the middle of a 12-period long-period grating, two symmetrical rejection bands at wavelengths of 1252.65 and 1418.7 nm are obtained with isolation higher than 18 dB and a passband bandwidth of 84.15 nm. The pi-phase-shifted long-period gratings are inscribed by the relaxation of mechanical stress with the focused pulses of a CO2 laser and a point-by-point technique without geometric deformation. The length of the spectral filter is approximately 6.6 mm with a sensitivity of 8 pm/ degrees C at a medium temperature range of 23-190 degrees C.     

Performance analysis of all optical swapping networks with a label eraser made of a Gaussian filter

In this paper, a simple label eraser employing Gaussian apodized fiber Bragg grating (FBG) for all optical label swapping (AOLS) networks is proposed. Relying on the analysis of the payload through multi-stage erasers, this kind of eraser significantly improves the cascadability in comparison with the traditional fiber-loop mirror (FLM) eraser. The influences of the residual labels on the intermediate swapping node labels through the eraser are also investigated. It is shown that the power penalty is only less 1 dB when the optical power ratio of residual label to the new label signal arrives at -8 dB. The influence is negligible due to the sharp notch filtering effect of the Gaussian apodized FBG.     

基于半导体光放大器四波混频效应的多种调制格式的波长转换实验

实验报道了利用半导体光放大器(SOA)的四波混频(FWM)效应实现多种码型的波长转换.其中对于非归零(NRZ)信号实现了从单信道到三信道的多波长转换.调制速率从10 Gb/s到40 Gb/s均实现多波长转换.对于归零(RZ)信号分别实现了20 Gb/s和40 Gb/s的RZ格式的波长转换和40 Gb/s的载波抑制归零(CSRZ)格式的波长转换,利用光纤布拉格光栅(FBG)作为带陷滤波器消除共轭光和抽运光之间的串扰.对于非归零差分相移键控(NRZ_DPSK)信号分别实现了20 Gb/s和40 Gb/s的波长转换,利用实验室自制的光纤延时干涉仪进行NRZ-DPSK信号的解调.基于FWM效应的转换光的输出消光比大于7 dB,转换后消光比退化约为3 dB.     

Strain-insensitive and high-temperature long-period gratings inscribed in photonic crystal fiber

We fabricate and demonstrate strain-insensitive and high-temperature long-period gratings in endlessly single-mode photonic crystal fiber by use of focused pulses of a CO2 laser and a periodic stress relaxation technique without geometrical deformation and elongation of the fiber. The thermal dependence of mode coupling at 1299.59 nm is 10.9 pm/degrees C from 24 to 992 degrees C, whereas the coefficient of strain sensitivity is -0.192 pm/muepsilon up to the maximum strain of 2.74%epsilon. It is found for what is believed to be the first time that, in contrast with the traditional fiber case, the coupling resonance shifts toward shorter wavelengths under applied strain, indicating that the refractive index of the core is decreased as a result of the rebuilding of tension attributed to the stress-elastic effect, and the cladding modes is highly dispersive because of airholes arranged in the fiber cladding.     

Large increase in photosensitivity through massive hydroxyl formation

We report a large increase in photosensitivity of germanium-doped silicate fibers by rapid heat treatment of hydrogen-loaded fibers at 1000 degrees C before exposure of the fibers to 242-nm radiation. The increase in photosensitivity is compared with thermally induced absorption caused by introduction of massive amounts of hydroxyl species. The absorption loss was measured to be 0.02 dB/cm mol.% OH at 1.55 mum. Strong gratings (Dn > 1 x 10(-4)) in germanium-free phosphorous-doped fibers in the presence of 242-nm radiation have also been manufactured by this technique.     

Tunable microwave photonic notch filter using a dual-wavelength fiber laser with phase modulation

A novel tunable microwave photonic notch filter using a phase-modulated dual-wavelength fiber laser is presented. A stable dual-wavelength erbium-doped fiber laser with a linear cavity is formed by a polarization-maintaining uniform fiber Bragg grating (PM-FBG) and a polarization maintaining linearly chirped fiber Bragg grating (PM-LCFBG), both of which were fabricated on a high-birefringence (Hi-Bi) fiber. It is found that a stable room-temperature dual-wavelength operation can be achieved due to the presence of two reflection peaks arising from the orthogonal states of polarization (SOP) of the PM-FBG. Experimental results show stable dual-wavelength lasing operation with a wavelength separation of ∼0.36 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. The dual-wavelength fiber laser is combined with a phase modulator and a segment of single-mode fiber (SMF) as a dispersive device to form a tunable microwave photonic notch filter. By stretching the PM-FBG to tune the wavelength separation of the dual-wavelength fiber laser, a tunable microwave photonic notch filter with various free spectral ranges (FSRs) and a rejection ratio greater than 35 dB was developed.     

In-fiber polymer-glass hybrid waveguide Bragg grating

A 1.2 microm (height) x 125 microm (depth) x 500 microm (length) microslot along a fiber Bragg grating was engraved across the optical fiber by femtosecond laser patterning and chemical etching. By filling epoxy in the slot and subsequent UV curing, a hybrid waveguide grating structure with a polymer core and glass cladding was fabricated. The obtained device is highly thermally responsive with linear coefficient of 211 pm/ degrees C.     

2-噻吩甲酰基-2-咔唑-N-丁基三氟丙酮化合物的合成与光谱研究

在苯和 5 0 %NaOH介质中 ,温度在 70～ 80℃时 ,1 ,4 二溴丁烷与咔唑 (CZ)反应 ,生成N 溴丁基咔唑 (BCZ)。在丙酮和K2 CO3 介质中 ,温度在 5 0℃时 ,N 溴丁基咔唑与噻吩甲酰三氟丙酮 (TTA)反应 ,生成 2 噻吩甲酰基 2 咔唑 N 丁基三氟丙酮 (TCBTA)。TCBTA为浅褐色针状结晶 ,熔点 2 1 1～ 2 1 4℃。详细研究了CZ ,BCZ ,TTA和TCBTA的紫外光谱和红外光谱 ,以及TCBTA的色谱 /质谱 ,证实了TCBTA合成产物的真实性。在氯仿中TCBTA的最大吸收波长为 2 4 1 ,2 6 5和 2 95nm ,摩尔吸光系数依次为 1 88× 1 0 5,1 2 5× 1 0 5和 1 0 8×1 0 5L·mol-1 ·cm-1 。TCBTA用于Fe(Ⅲ )和Nd(Ⅲ )的萃取 ,萃取率比TTA分别高 3倍和 1 6倍 ,与Nd(Ⅲ )形成络合物的荧光强度 ,TCBTA是TTA的 6倍 ,表明TCBTA具有优良的光敏特性。     

Compact and monolithic coarse wavelength-division multiplexer-demultiplexer fabricated by use of a high-spatial-frequency transmission grating buried in a slab waveguide

A compact and monolithic four-channel demultiplexer with 20-nm spacing was fabricated by use of a high-spatial-frequency transmission grating buried in a silica waveguide. The grating was successfully buried in a silica slab waveguide by overcladding by plasma-enhanced chemical-vapor deposition. The device's size was approximately 5.1 mm x 9.2 mm. The average insertion loss was 13 dB. The average cross talk was -15 dB for adjacent channels and -19 dB for nonadjacent channels. The polarization-dependent loss was estimated to be as low as 0.7 dB.     

Spectral and level effects in noise-on-tone suppression

The effective internal level of a 1-kHz tone at 50 dB SPL was estimated by measuring the forward masking produced on a 10-ms signal tone of the same frequency. Noise containing a spectral notch was then added to the masker tone, and its influence on the effective level of the tone was measured with a variety of noise levels, notch widths, and notch shapes. In experiment 1, the masker tone was centered in the spectral notch, itself centered in a 2-kHz band of noise. As the spectrum level in the noise passbands increased from 6 dB/Hz to 36 dB/Hz, signal threshold decreased, indicating a decrease in masking by the masker tone. This "unmasking" effect of the noise was attributed to suppression of the masker tone by the components in the noise. Unmasking was greatest with the narrowest spectral notch (250 Hz), and decreased to zero as the notch widened to 1500 Hz. Compared to its level when presented alone, the effective internal level of the masker tone could be reduced by up to 30 dB (250-Hz notch, 36 dB/Hz). The relative suppressive strength of individual noise components was estimated in experiment 2, in which the 1-kHz masker tone was located at one edge of a spectral notch, rather than in the center. Noise spectrum level was fixed at 16 dB/Hz. As notch width decreased to zero, on either the high-frequency or low-frequency side of the masker tone, its effective internal level was again reduced by approximately 30 dB. In a tentative analysis, the first derivative of the smoothed threshold function was taken, to provide an estimate of the relative contributions to suppression at 1 kHz of noise components between 250 and 1740 Hz.(ABSTRACT TRUNCATED AT 250 WORDS)     

Wide-range tuning of polymer microring resonators by the photobleaching of CLD-1 chromophores

We present a simple and effective method for the postfabrication trimming of optical microresonators. We photobleach CLD-1 chromophores to tune the resonance wavelengths of polymer microring resonator optical notch filters. A maximum wavelength shift of -8.73 nm is observed. The resonators are fabricated with a soft-lithography molding technique and have an intrinsic Q value of 2.6 x 10(4) and a finesse of 9.3. The maximum extinction ratio of the resonator filters is -34 dB, indicating that the critical coupling condition has been satisfied.     

Improved stabilization of a 1.3 microm femtosecond optical frequency comb by use of a spectrally tailored continuum from a nonlinear fiber grating

We report significant enhancement (+24 dB) of the optical beat note between a 657 nm cw laser and the second-harmonic generation of the tailored continuum at 1314 nm generated with a femtosecond Cr:forsterite laser and a nonlinear fiber Bragg grating. The same continuum is used to stabilize the carrier-envelope offset frequency of the Cr:forsterite femtosecond laser and permits improved optical stabilization of the frequency comb from 1.0 to 2.2 microm. Using a common optical reference at 657 nm, a relative fractional frequency instability of 2.0 x 10(-15) is achieved between the repetition rates of Cr:forsterite and Ti:sapphire laser systems in 10 s averaging time. The fractional frequency offset between the optically stabilized frequency combs of the Cr:forsterite and Ti:sapphire lasers is +/-(0.024 +/- 6.1) x 10(-17).     

Deep-notch, ultracompact long-period grating in a large-mode-area photonic crystal fiber

An extremely short long-period grating (LPG) with strong resonance has been developed in a large-mode-area photonic crystal fiber (PCF) by use of the heat source of a CO2 laser. We believe that such a LPG in pure silica PCF is the first example to be obtained with the point-by-point technique. The fabrication method is simple and repeatable. The resulting LPG has 8 periods, written by a CO2 laser, within a 2.8-mm length of fiber, which yields a deep notch of core-cladding mode coupling of -31.5 dB at the telecommunication wavelength of 1529.2 nm, with a FWHM of approximately 0.7 nm. The principal advantages of this LPG are that it is practical, cost effective, and compact.