应用聚L-色氨酸/石墨烯修饰电极同时测定尿酸和黄嘌呤

将玻碳电极(GCE)放入含有L-色氨酸(TR)和氧化石墨烯(GO)底液进行循环扫描聚合,得到聚L-色氨酸(PTR)和电化学还原石墨烯(ERGO),从而制备了PTR-ERGO/GCE,电极具有较快的电子传递速率和较好的催化能力。利用循环伏安法(CV)和差分脉冲伏安法(DPV)探究尿酸(UA)和黄嘌呤(Xa)在该电极上的电化学行为。UA和Xa在电极表面的氧化过程均受吸附和扩散共同控制,以扩散为主。在最佳条件下,UA在0.626 V处产生一个氧化峰,Xa在0.994 V处产生一个氧化峰,两峰分开0.368 V,不需分离,即可同时进行测定。采用DPV法同时测定UA和Xa的线性范围分别为5.0×10-8~2.0×10-4mol/L和1.0×10-7~2.0×10-4mol/L,检出限分别为10和30 nmol/L。方法已用于人体尿样中尿酸和黄嘌呤的同时测定。     

肉桂酸修饰电极同时测定多巴胺和抗坏血酸的研究

用电化学聚合方法制备肉桂酸(CA)修饰的玻碳电极(PCA/GC),研究多巴胺(DA)和抗坏血酸(AA)在修饰电极上的电化学行为.结果表明,在DA和AA共存体系中,DA、AA在PCA/GC电极上氧化峰电流增大且氧化峰电位相差200 mV,据此可同时检测DA和AA.在pH 7.0磷酸盐缓冲液中,DA和AA的氧化峰电流与其浓...     

纳米铜修饰电极对多巴胺和抗坏血酸的同时测定

用电沉积方法制备了纳米铜修饰电极并将其用于混合溶液中多巴胺(DA)和抗坏血酸的同时测定。在优化的实验条件下,修饰电极对多巴胺和抗坏血酸具有良好的电催化响应,多巴胺的峰电流与浓度在8.0×10-7mol/L~1.0×10-4mol/L范围内成很好的线性关系,抗坏血酸的氧化峰电流与其浓度在8.0×10-6mol/L~1.0×10-3mol/L的范围成良好的线性关系。该修饰电极制备简单、稳定性好,用于样品检测,效果良好。     

用修饰电极导数伏安法同时测定多巴胺和肾上腺素

研究了２,６－吡啶二甲酸在玻碳电极上电化学聚合的实验条件及修饰电极的电化学特性,发现该聚合物膜修饰电极对多巴胺和肾上腺素的电化学氧化有显著的催化作用,而对抗坏血酸等阴离子没有响应。利用在修饰电极上循环伏安阴极过程多巴胺和肾上腺素的峰电位不同,采用阴极化导数伏安法可同时测定多巴胺和肾上腺素。     

聚L-精氨酸修饰电极存在下同时测定多巴胺和肾上腺素

用循环伏安法制备了聚L-精氨酸修饰玻碳电极,研究了多巴胺和肾上腺素在修饰电极上的电化学行为,建立了同时测定多巴胺和肾上腺素的新方法。在pH7.5的磷酸盐缓冲溶液中,多巴胺在修饰电极上产生一对氧化还原峰,峰电位分别为0.276V和0.059V;肾上腺素在修饰电极上产生3个氧化峰和一个还原峰,峰电位分别为0.262V、0.121V、-0.126V和-0.316V(对Ag/AgCl电极)。多巴胺和肾上腺素同时存在时ΔEpc=375mV,用还原峰对多巴胺和肾上腺素同时测定的线性范围分别为8.0×10-7~5.0×10-4mol/L和5.0×10-7~5.0×10-5mol/L;检出限分别为3.0×10-7mol/L和1.0×10-7mol/L。大量的抗坏血酸和尿酸不干扰测定,用于人尿液中多巴胺和肾上腺素样品的同时测定,结果满意。     

应用单壁碳纳米管修饰纳米碳纤维电极同时测定多巴胺和抗坏血酸

采用滴涂法制备了单壁碳纳米管修饰的纳米碳纤维电极,研究了多巴胺(DA)、抗坏血酸(AA)及其混合溶液在修饰前后电极上的电化学行为。在20 mmol/L Tris-HCl(pH 7.4)缓冲溶液中,修饰电极对DA和AA具有很好的电催化作用。采用差示脉冲伏安法对DA与AA混合溶液氧化峰电流与浓度的关系进行定量分析,DA和AA的氧化峰电流在1.0×10-7~5.0×10-5mol/L和1.0×10-5~1.0×10-3mol/L范围内与浓度呈线性关系,其线性回归方程及相关系数分别为Ip=0.0012c+4×10-9,r=0.9907;Ip=10-5c+7×10-10,r=0.9974,两种物质的检测限分别达到8.0×10-9mol/L和2×10-6mol/L。     

同时测定多巴胺和肾上腺素的大环镍膜修饰电极

研究了大环镍膜修饰电极对多巴胺和肾上腺素的电化学响应特性；结果表明，该修饰电极对多巴胺和肾上腺素的电极反应具有良好的催化活性，多巴胺和肾上腺素在修饰电极上的氧化电位比在裸铂电极上分别负移了230mV和70mV，使二者的阳极峰得到很好的分离，且灵敏度大为提高；将该修饰电极用于多巴胺和肾上腺素的同时检测，获得满意结果，生物体中的主要干扰物质抗坏血酸和NO2^-等均不干扰测定。     

聚多巴胺-还原氧化石墨烯修饰电极同时测定邻苯二酚和对苯二酚

制备了聚多巴胺-还原氧化石墨烯修饰玻碳电极(PDA-rGO/GCE),以此修饰电极作为工作电极,采用循环伏安法(CV)对邻苯二酚(CC)和对苯二酚(HQ)的电化学行为进行了研究。结果表明CC和HQ在该修饰电极上的峰电流与氧化石墨烯修饰电极相比有了明显增高,并且它们的氧化峰电位差和还原峰电位差均超过110 mV,证明该修饰电极用于两种酚的同时检测是可行的。在优化实验条件下,采用微分脉冲伏安法(DPV)对CC和HQ同时进行检测,CC和HQ的峰电流与其浓度均在1.0×10~(-6)～4.0×10~(-3) mol/L范围内呈良好的线性关系,检出限(S/N=3)分别为2.0×10~(-7) mol/L和3.6×10~(-7) mol/L。以所制备的修饰电极对自来水水样和湖水水样进行了加标回收检测,回收率在97.6%～100.6%范围内。     

碳纳米管修饰电极对多巴胺和肾上腺素的电分离及同时测定

研究了多巴胺 (DA)和肾上腺素 (EP)在多壁碳纳米管 (MWNT)修饰电极上的电化学性质 ,发现该修饰电极对神经递质DA和EP有显著的增敏和电分离作用。还原峰电位差达ΔEp=390mV ,可同时测定DA和EP。DA和EP的还原峰电流与其浓度分别在 2 .0× 10 -6～ 1.0× 10 -3 mol/L和 1.0× 10 -6～ 1.0× 10 -3 mol/L浓度范围内呈良好的线性关系 ;方法的检出限分别为 1× 10 -6mol/L和 5× 10 -7mol/L。由于抗坏血酸 (AA)在MWNT修饰电极上的氧化是不可逆的 ,因此利用还原峰进行测定 ,消除了AA对DA和EP的干扰     

Simultaneous determination of dopamine and serotonin using a carbon nanotubes-ionic liquid gel modified glassy carbon electrode

An electrochemical sensor based on carbon nanotubes (CNTs)-ionic liquid (IL) composite has been developed for the simultaneous determination of serotonin (5-HT) and dopamine (DA). The CNTs-IL composite modified electrode presents excellent selectivity and sensitivity towards 5-HT and DA and eliminates the interference of ascorbic acid. The parameters which influence the determination of 5-HT and DA have been investigated. Under optimized conditions, linear calibration graphs were obtained in the range from 20 nM to 7 µM, with a detection of limit of 8 nM, for 5-HT, and in the range from 0.1 to 12 µM, with a detection of limit of 60 nM, for DA. The electrode has been applied to the assay of 5-HT and DA in human blood serum with good results.     

聚精氨酸修饰玻碳电极上多巴胺的电化学特性及其检测

用循环伏安法制备了聚精氨酸修饰玻碳电极,研究了神经递质多巴胺在该聚合物薄膜修饰电极上的电化学行为及其检测。在pH7.0的磷酸盐缓冲溶液中,多巴胺在聚精氨酸修饰电极上于0.19V和0.16V处出现一对灵敏、可逆的氧化还原峰。在最佳测试条件下,氧化峰电流与多巴胺的浓度在3.0×10-7~8.0×10-4mol/L范围内呈良好的线性关系,线性回归方程为Ipa(μA)=86.063C(mmol/L) 20.183,相关系数r=0.9993,最低检测限(3σ)5.0×10-8mol/L。用于多巴胺针剂含量的测定,结果满意。     

Simultaneous determination of dopamine and ascorbic acid on poly (3,4-ethylenedioxythiophene) modified glassy carbon electrode

Detection of dopamine (DA) in the presence of excess of ascorbic acid (AA) has been demonstrated using a conducting polymer matrix, poly (3,4-ethylenedioxythiophene) (PEDOT) film in neutral buffer (PBS 7.4) solution. The PEDOT film was deposited on a glassy carbon electrode by electropolymerization of EDOT from acetonitrile solution. Atomic force microscopy studies revealed that the electrodeposited film was found to be approximately 100 nm thick with a roughness factor of 2.6 nm. Voltammetric studies have shown catalytic oxidation of DA and AA on PEDOT modified electrode and can afford a peak potential separation of ∼0.2 V. It is speculated that the cationic PEDOT film interacts with the negatively charged ascorbate anion through favorable electrostatic interaction, which results in pre-concentration at a less anodic value. The positively charged DA tends to interact with the hydrophobic regions of PEDOT film through hydrophobic–hydrophobic interaction thus resulting in favorable adsorption on the polymer matrix. Further enhancement in sensitivity to micro molar level oxidation current for DA/AA oxidation was achieved by square wave voltammetry (SWV) which can detect DA at its low concentration of 1 μM in the presence of 1000 times higher concentration of AA (1 mM). Thus the PEDOT modified electrode exhibited a stable and sensitive response to DA in the presence of AA interference.     

Highly selective dopamine quantification using a glassy carbon electrode modified with a melanin-type polymer

A highly selective dopamine quantification at a new polymer-modified electrode in the presence of large excess of ascorbic acid and 3,4-dihydroxyphenyl acetic acid (dopac) is described. The electrochemical detection was performed at a glassy carbon electrode modified with a melanin-type polymer obtained by polymerization of 3.0×10⁻³ M -dopa in 0.050 M phosphate buffer solution pH 7.40 by applying 1.00 V for 60 min. The polymeric film exhibits attractive permselectivity excluding anionic species such as potassium ferricyanide, ascorbic acid, dopac and uric acid. Cationic species such as epinephrine, norepinephrine and dopamine and neutral ones such as catechol and hydrogen peroxide can be oxidized at the polymer-modified electrode. The use of ascorbic acid in the measurement solution allows the amplification of dopamine oxidation signal due to the reduction of the electrochemically generated dopaminequinone. By using 1.0×10⁻³ M ascorbic acid, the detection limit for dopamine is 5.0 nM. The interference for the maximum physiological concentrations of ascorbic acid and dopac in nervous centers, i.e. 500 μM ascorbic acid and 50 μM dopac is 8.1 and 1.4%, respectively.     

Electrochemical sensor using glassy carbon electrode modified with acylpyrazolone-multiwalled carbon nanotube composite film for determination of xanthine

In this work, an electrochemical sensor 1-phenyl-3-methyl-4-(2-furoyl)-5-pyrazolone/multiwalled carbon nanotubes/glassy carbon electrode (GCE) was prepared for the determination of xanthine (XN) in the presence of an excess of uric acid. Cyclic voltammetry and differential pulse voltammetry were used to characterize the electrode. The oxidation of XN occurred in a well-defined peak having E _p 0.73 V in phosphate buffer solution of pH 6.0. Compared with the bare GCE, the electrochemical sensor greatly enhanced the oxidation signal of XN with negative shift in peak potential about 110 mV. Based on this, a sensitive, rapid, and convenient electrochemical method for the determination of XN has been proposed. Under the optimized conditions, the oxidation peak current of XN was found to be proportional to its concentration in the range of 0.3~50 μM with a detection limit of 0.08 μM. The analytical utility of the proposed method was demonstrated by the direct assay of XN in urine samples and was found to be promising at our preliminary experiments.     

Simultaneous determination of ascorbic acid, dopamine, uric acid and xanthine using a nanostructured polymer film modified electrode

This paper describes the simultaneous determination of ascorbic acid (AA), dopamine (DA), uric acid (UA) and xanthine (XN) using an ultrathin electropolymerized film of 2-amino-1,3,4-thiadiazole (p-ATD) modified glassy carbon (GC) electrode in 0.20 M phosphate buffer solution (pH 5.0). Bare GC electrode failed to resolve the voltammetric signals of AA, DA, UA and XN in a mixture. On the other hand, the p-ATD modified electrode separated the voltammetric signals of AA, DA, UA and XN with potential differences of 110, 152 and 392 mV between AA-DA, DA-UA and UA-XN, respectively and also enhanced their oxidation peak currents. The modified electrode could sense 5 μM DA and 10 μM each UA and XN even in the presence of 200 μM AA. The oxidation currents were increased from 30 to 300 μM for AA, 5 to 50 μM for DA and 10 to 100 μM for each UA and XN, and the lowest detection limit was found to be 2.01, 0.33, 0.19 and 0.59 μM for AA, DA, UA and XN, respectively (S/N = 3). The practical application of the present modified electrode was demonstrated by the determination of AA, UA and XN in human urine samples.     

Simultaneous determination of hydroquinone and catechol based on glassy carbon electrode modified with gold-graphene nanocomposite

We have synthesized a virtually monodisperse gold-graphene (Au-G) nanocomposite by a single-step chemical reduction method in aqueous dimethylformamide solution. The nanoparticles are homogenously distributed over graphene nanosheets. A glassy carbon electrode was modified with this nanocomposite and displayed high electrocatalytic activity and extraordinary electronic transport properties due to its large surface area. It enabled the simultaneous determination of hydroquinone (HQ) and catechol (CC) in acetate buffer solution of pH?4.5. Two pairs of well-defined, quasi-reversible redox peaks are obtained, one for HQ and its oxidized form, with a 43 mV separation of peak potentials (ΔE_p), the other for CC and its oxidized form, with a ΔE_p of 39 mV. Due to the large separation of oxidation peak potentials (102 mV), the concentrations of HQ and CC can be easily determined simultaneously. The oxidation peak currents for both HQ and CC increase linearly with the respective concentrations in the 1.0 μM to 0.1 mM concentration range, with the detection limits of 0.2 and 0.15 μM (S/N?=?3), respectively. The modified electrode was successfully applied to the simultaneous determination of HQ and CC in spiked tap water, demonstrating that the Au-G nanocomposite may act as a high-performance sensing material in the selective detection of some environmental pollutants.

Docosyltrimethylammonium chloride modified glassy carbon electrode for simultaneous determination of dopamine and ascorbic acid

A glassy carbon electrode (GCE) modified with docosyltrimethylammonium chloride (DCTMACl) is used for simultaneous determination of dopamine (DA) and ascorbic acid (AA) using differential pulse voltammetry (DPV) technique in 0.10 mol·L^?1 phosphate buffer solution of pH 5.0. The cationic surfactant DCTMACl modified film has a positive charge. DA exists as the positively charged species, whereas AA is the negatively charged one in the solution. Thus, at DCTMACl film-modified GCE, the oxidation peak potential of AA shifts toward less negative potential and the peak current of AA increases a little, while the oxidation peak potential of DA shifts toward more positive potential and peak current decreases greatly in comparison with that on bare electrode. The two anodic peaks are separated around 200 mV. Under optimal conditions, the catalytic peak currents obtained from DPV increase linearly with concentrations of DA and AA in the ranges of 1.0?×?10^?5 to 1.0?×?10^?3?mol·L^?1. This electrode has good reproducibility, high stability in its voltammetric response, and low detection limit (micromolar) for both AA and DA. The modified electrode has been applied to the determination of DA and AA in injection.     

Enhanced voltammetric determination of dopamine using a glassy carbon electrode modified with ionic liquid-functionalized graphene and carbon dots

The authors describe a dopamine (DA) sensor based on a glassy carbon electrode modified with a composite film composed of carbon dots (C-dots) and graphene functionalized with an ionic liquid. The C-dots were functionalized with carboxy groups whose negative charge promotes electrostatic attraction to the protonated amino groups in DA. The presence of an imidazole cation in the IL facilitates interaction with the C-dots and DA via electrostatic interactions and π-stacking forces. Under optimal conditions, the modified GCE display improved electrochemical response to DA compared to a bare GCE, or a GCE modified with C-dots or IL-graphene only. The oxidation current, measured best at a potential of 0.22 V (vs. Ag/AgCl) is linearly related to the DA concentration in the 0.1 to 600 μM range, with a 30 nM detection limit at a signal-to-noise ratio of 3. Ascorbic acid does not interfere even in large excess, and the sensor is stable for at least a month. The modified GCE was applied to the determination of DA in spiked fetal bovine serum and gave satisfactory results.