多孔钛基掺硼金刚石电极结构对电催化降解阿司匹林性能的影响

利用扫描电子显微镜(SEM)和X射线衍射仪(XRD)对多孔Ti/BDD电极及传统平板Ti/BDD(BDD=钛基掺硼金刚石)电极进行了研究,通过循环伏安法考察了电极的背景电流和电化学窗口.以阿司匹林为模型污染物,研究了BDD电极结构对阿司匹林电催化降解的影响.结果表明,多孔Ti/BDD电极的总带电量,内、外部带电量,孔隙率和比表面积均高于平板Ti/BDD电极;多孔Ti/BDD在对COD和阿司匹林的去除率和能量消耗等方面均优于平板Ti/BDD电极.     

掺硼金刚石电极电催化氧化酚类有机物的取代基效应

本文主要以当前水环境中存在酚类有机污染物为研究对象,探讨酚类有机污染物在掺硼金刚石(BDD)电极上的取代基效应,具体研究具有不同位置及种类官能团的取代酚类有机污染物在BDD电极上的电催化氧化过程,通过化学需氧量和浓度变化考察有机污染物在电催化降解过程中的降解趋势,深入分析电极种类、官能团位置与种类与电催化氧化活性之间的联系的同时,研究阳极材料电催化氧化有机污染物的机理及动力学。结果表明,有机物在电极表面的电催化过程以电产生羟基自由基为媒介,对苯二酚在不同电极上的电催化活性与电极析氧电位及表面产生羟基自由基量有着重要的联系,BDD电极拥有最强的电催化氧化活性;不同取代基团的对位取代酚在BDD电极上的电化学降解实验显示电催化反应速率受取代官能团自身的电子效应制约,有机物矿化过程中羟基自由基首先进攻苯环的对位发生取代反应,同时取代基脱离苯环过程成为整个取代酚类电化学降解过程的决速步骤,且有机物的电催化反应速率与取代基特征Hammett常数σ呈近似线性关系。     

碳纳米管复合聚对氨基吡啶修饰电极伏安法同时测定硝基酚异构体的研究

利用导电聚合物的分子识别性和碳纳米管奇特的物理化学性质, 制备了碳纳米管复合聚对氨基吡啶(SWNTs/POAP)修饰电极, 研究了邻、间、对硝基酚异构体同时在该电极上的电化学响应. 实验结果表明, 邻、间、对硝基酚异构体在SWNTs/POAP纳米电极界面具有不同的构象, 其氧化峰电位能够完全分开, 并能显著地提高电化学测定的灵敏度. 文中的SWNTs/POAP纳米电极制备简单方便, 可用于硝基酚位置异构体的同时电化学量测.     

双酚A在硼掺杂金刚石薄膜电极上的电化学行为研究

硼掺杂金刚石(BDD)薄膜电极是用于废水处理的理想电极材料。利用循环伏安法和电化学阻抗谱研究了环境激素双酚A(BPA)在BDD电极上的电化学行为,分析在电极/溶液界面上的电化学过程及相关的电极动力学参数。研究发现BPA在电极上的直接电化学氧化过程为不可逆过程,氧化峰电势在1.4 V左右。电极/溶液界面的双电层结构可以用一个电容与一个电阻并联的等效电路来进行拟合,当极化电位从0.5 V增加至2.0 V时,电荷转移电阻Rct由7.043×104Ω·cm2降至1.366×103Ω·cm2,下降了80.60%,表明提高电极电位可明显降低电催化反应的电阻,有利于电催化氧化反应的进行,可提高电催化反应速率。     

Ti/α-PbO2/β-PbO2电极电化学降解2-氯酚

采用电化学沉积法在Ti基底上制备了复合电极Ti/α-PbO2/β-PbO2,扫描电镜结果表明电极呈现由β-PbO2小晶体组成的菜花状微观形貌.所制电极在电化学降解环境污染物2-氯酚时表现出较高的电催化效率、较好的电极稳定性和较长的电极寿命.用正交实验优化了电化学降解2-氯酚的实验条件.在最优的实验条件(2-氯酚初始浓度50 mg/L,电解质0.1 mol/L Na2SO4,温度35oC,阳极电流密度20 mA/cm2)下电化学降解180 min后,2-氯酚的去除率达100%.动力学结果表明, Ti/α-PbO2/β-PbO2电极上2-氯酚的电化学氧化符合准一级动力学过程.     

硼掺杂金刚石薄膜电极上二氯酚的电化学阻抗谱研究

以2,4-二氯酚(2,4-DCP)和2,6-二氯酚(2,6-DCP)为模型污染物,采用循环伏安法和电化学阻抗谱研究了硼掺杂金刚石(BDD)电极上2种氯酚的电催化氧化过程.结果表明,2,4-DCP和2,6-DCP的氧化电位分别为1.55和1.62 V.等效电路拟合结果表明,当极化电位由开路电位提高至1.5 V时,2种氯酚的电荷转移电阻均有明显下降,反应控制步骤为扩散控制步骤.与2,6-DCP相比,2,4-DCP在BDD电极上更容易发生直接电化学氧化.     

Ti/α-PbO_2/β-PbO_2电极电化学降解2-氯酚（英文）

采用电化学沉积法在Ti基底上制备了复合电极Ti/α-PbO 2/β-PbO 2,扫描电镜结果表明电极呈现由β-PbO 2小晶体组成的菜花状微观形貌.所制电极在电化学降解环境污染物2-氯酚时表现出较高的电催化效率、较好的电极稳定性和较长的电极寿命.用正交实验优化了电化学降解2-氯酚的实验条件.在最优的实验条件(2-氯酚初始浓度50 mg/L,电解质0.1 mol/L Na2SO4,温度35 oC,阳极电流密度20 mA/cm2)下电化学降解180 min后,2-氯酚的去除率达100%.动力学结果表明,Ti/α-PbO 2/β-Pb O2电极上2-氯酚的电化学氧化符合准一级动力学过程.     

邻苯二甲酸二甲酯在三维多孔钛基掺硼金刚石薄膜电极上的电催化氧化行为

以邻苯二甲酸二甲酯(DMP)作为模型污染物,研究了不同结构的钛基体对掺硼金刚石薄膜(Ti/BDD)电极电催化性能的影响.结果表明,三维多孔电极为氧化还原反应提供了更多的反应活性位点,表现出更快的电子传递速率.通过循环伏安法和线性扫描法验证了DMP在BDD电极上的电催化氧化行为属于直接电氧化过程,且在低浓度下近似为一级反应,DMP浓度较高时会在BDD电极表面发生成膜现象.在不同浓度的DMP溶液中使用平板Ti/BDD电极及多孔Ti/BDD电极进行直接电催化氧化时,DMP的电催化氧化过程与理论推断一致;多孔电极由于其电活性面积的优势在COD和DMP的去除方面均优于平板电极.     

纳米晶碳化钨薄膜对硝基甲烷还原的电催化性能

采用磁控溅射物理气相沉积技术在金属镍基体上制备碳化钨纳米晶薄膜. 薄膜具有纳米晶结构, 由粒径为20~35 nm的晶粒构成, 晶粒分布均匀, 晶相结构为非化学计量比的碳化钨(WC1-x). 采用电化学方法研究硝基甲烷在纳米晶碳化钨薄膜电极上的电化学还原性能和反应机理. 实验结果表明, 碳化钨薄膜电极对硝基甲烷电化学还原反应具有较好的催化性能, 当电极电位为-0.89 V(vs.SCE)时, 硝基甲烷还原为甲基羟胺的电流达14.9 mA/cm2, 其反应表观活化能为12.3 kJ/mol. 硝基甲烷在碳化钨薄膜电极上经过一步不可逆的电化学反应还原成甲基羟胺, 其控制步骤是电极反应的电荷传递过程.      

纳米SnO2/TiO2电极的制备及其电催化降解间-硝基苯酚

用电化学方法在乙二醇溶液中制备锡、钛醇盐配合物Sn0.75Ti(OCH2CH2OH)(7-x),将电解液水解、干燥后在400℃煅烧2 h,得到纳米级SnO2/TiO2粉体。通过红外光谱(FT-IR)和拉曼光谱(Raman)对电解产物进行测试,纳米SnO2/TiO2粉体通过X射线粉末衍射(XRD)和扫描电子显微镜(SEM)进行表征。实验表明,在有机体系电解得到的纳米SnO2/TiO2粉体颗粒分散较理想,粒径在100～200 nm。再通过溶胶-凝胶法在钛丝表面得到纳米SnO2/TiO2电极,采用循环伏安法研究电极在酸性溶液和间-硝基苯酚溶液中的氧化还原行为和电催化活性。结果表明,纳米TiO2掺杂SnO2电极的氧化峰电流达到143×10-3A/cm2,氧化还原峰电位差明显减小,催化降解间-硝基苯酚的COD去除率达到86.1%,具有较高的电催化活性。     

流动注射-电化学氧化法测定水体化学需氧量

采用硼掺杂金刚石(Boron-doped diamond,BDD)薄膜电极为工作电极,利用流动注射分析方法测定水体化学需氧量(COD),根据水样中有机物组分在工作电极表面氧化消耗的电量(Qoxidation)测定样品的COD值。考察了一些基本参数包括载液、工作电位、流速对检测信号的影响并选定了最佳检测条件。在最佳检测条件下,本法检测COD的线性范围为2.5~120 mg/L,检出限为1 mg/L。用该法测定化工厂和食品厂废水的COD值,相对标准偏差和回收率分别在2.4%~4.8%和96%~106%之间,且检测结果与国家标准方法(CODcr法)有良好的一致性。     

Synthesis and Temperature-dependent Electrochemical Properties of Boron-doped Diamond Electrodes on Titanium

On the sand-blasting-treated titanium(Ti) substrate, the boron-doped diamond(BDD) electrodes with a wide potential window were prepared by microwave plasma chemical vapor deposition(MPCVD). The electrochemical oxidation ratios of phenol at BDD/Ti electrodes at elevated temperatures(from 20 ℃ to 80 ℃) were examined by the chemical oxygen demand(COD) of phenol electrolyte during electrolysis. The results show that the COD removal was increased at high temperatures and the optimized temperature for enhancing the electrochemical oxidation ratio of phenol is 60 ℃. The mechanism for the temperature-dependent electrochemical oxidation ratios of phenol at the electrodes was investigated. The study would be favorable for further improving the performance of BDD/Ti electrodes, especially working at high temperatures.     

Condition optimization of amperometric determination of chemical oxygen demand using boron-doped diamond sensor

The amperometric determination of chemical oxygen demand (COD) reported by Quan Xie??s group (Electrochem Commun 9:2281, 14), was a rapid, green and simple COD evaluation method. This work focused on testing and verifying this method by using a home-made boron-doped diamond (BDD) film as anode and optimizing the experiment conditions. The BDD thin film electrode was employed as anode and the electrochemical process was run with different experimental parameters including counter electrode, electrode gap, applied potential, electrolyte pH, and temperature. Standard samples were determined in the optimum conditions, a linear range of 19.2?C11,600?mg l^?1 COD and a low detection limit of 0.192?mg l^?1 COD were well established with the present approach. The COD value of the simulated organic wastewater determined by this method agreed well with the standard dichromate method, and it showed good accuracy, stability, and reproducibility.     

Hydroxyl radicals electrochemically generated in situ on a boron-doped diamond electrode

The hydroxyl radicals electrochemically generated in situ on a boron-doped diamond (BDD) electrode have been investigated for the first time in different electrolyte media, over the whole pH range between 1 and 11. A more extensive characterisation of BDD electrochemical properties is very important to understand the reactivity of organic compounds towards electrochemical oxidation on the BDD electrode, which is related to their interaction with adsorbed hydroxyl radicals due to water oxidation on the electrode surface. An oxidation peak corresponding to the transfer of one electron and one proton was observed in pH <9 electrolytes, associated with the water discharge process and electrochemical generation of hydroxyl radicals, which can interact and enhance the electro-oxidation of organic compounds. In pH >9 electrolytes the electrochemical generation of hydroxyl radicals was not observed; ammonia buffer electrolyte gave a pH-independent peak corresponding to the ammonia oxidation reaction. Additionally, for most pH values studied, a few small peaks associated with the electrochemical interaction between non-diamond carbon species on the doped diamond electrode surface and the electrolyte were also seen, which suggests that the doped diamond is relatively unreactive, but not completely inert, and the electrogenerated hydroxyl radicals play a role as mediator in the oxidation of organics.     

金刚石薄膜电化学

金刚石由于其特殊的物理与化学性质,早在几百年前就吸引了人们对它的关注.化学气相沉积(chemical vapor deposition,CVD)法制备的高掺杂硼复合多晶金刚石薄膜,为金刚石薄膜在电化学中的应用开辟了新的领域.作为新型碳素电极材料,高掺杂硼复合多晶金刚石薄膜具有许多目前使用的电极材料所不可比拟的优异特性如:宽电化学势窗,低残留电流,极好的电化学稳定性以及表面不易被污染等.本文综述了高掺杂硼复合多晶金刚石薄膜电极在电化学中的几个重要应用,包括电分析、电合成及电化学法处理废水等.     

Photocatalytically-assisted electrochemical degradation of <Emphasis Type="Italic">p</Emphasis>-aminophenol in aqueous solutions using zeolite-supported TiO<Subscript>2</Subscript> catalyst

This paper reports the results of an investigation into enhancement of the electrochemical oxidation of p-aminophenol (4-AP) in an aqueous solution with a boron-doped diamond (BDD) electrode, assisted by photocatalysis using a zeolite-supported TiO₂ (Z-TiO₂) catalyst. The BDD electrode was characterised in 0.1 M Na₂SO₄-supporting electrolyte and the presence of 4-AP by open-circuit potential behaviour (OCP) and cyclic voltammetry (CV). The electrode behaviour was investigated in the dark and following UV irradiation and in the absence/presence of the Z-TiO₂ catalyst. The electro-oxidation process was carried out using chronoamperometry (CA) and multiple-pulsed amperometry (MPA) at the selected potential under potentiostatic conditions. The electrochemical degradation process of 4-AP on the BDD electrode was improved by the application of a pulsed potential, which allowed both in-situ electrochemical cleaning of the electrode and indirect oxidation of 4-AP by oxygen evolution. The application of photocatalysis using Z-TiO₂ in the 4-AP electrochemical degradation exhibited an enhanced effect when the anodic potential was set at +1.25 V vs. Ag/AgCl in the water stability region, close to the oxygen evolution potential.     

Electroanalysis of tetracycline using nickel-implanted boron-doped diamond thin film electrode applied to flow injection system.

The electrochemical analysis of tetracycline was investigated using nickel-implanted boron-doped diamond thin film electrode by cyclic voltammetry and amperometry with a flow injection system. Cyclic voltammetry was used to study the electrochemical oxidation of tetracycline. Comparison experiments were carried out using as-deposited boron-doped diamond thin film electrode (BDD). Nickel-implanted boron-doped diamond thin film electrode (Ni-DIA) provided well-resolved oxidation irreversible cyclic voltammograms. The current signals were higher than those obtained using the as-deposited BDD electrode. Results using nickel-implanted boron-doped diamond thin film electrode in flow injection system coupled with amperometric detection are presented. The optimum potential for tetracycline was 1.55 V versus Ag/AgCl. The linear range of 1.0 to 100 microM and the detection limit of 10 nM were obtained. In addition, the application for drug formulation was also investigated.     

Non-enzymatic electrochemical detection of glycerol on boron-doped diamond electrode

A non-enzymatic direct electrochemical glycerol detection method at a commercial boron-doped diamond (BDD) electrode in 0.1 M NaOH supporting electrolyte was developed. All the used electrochemical techniques proved useful features for the oxidation and direct amperometric determination of glycerol at a BDD electrode in 0.1 M NaOH aqueous solution. It was found that the direct electrooxidation of glycerol on the BDD electrode requires both adsorbed glycerol and hydroxyls at the electrode surface. Also, the sp(2) carbon did not allow enhancement of the glycerol oxidation process. The electronalytical sensitivity for the determination of glycerol at the BDD electrode ranged from 0.040 to 0.226 μA mM(-1) as a function of the technique used. The highest electroanalytical sensitivity for the determination of glycerol at the BDD electrode was reached in batch system amperometric quantification under stirring conditions. Performed recovery studies indicated that it is possible to determine glycerol in real samples, and the proposed batch system analysis-based methodology can be a valuable tool for practical glycerol analysis.     

Direct and Simultaneous Determination of Phenol, Hydroquinone and Nitrophenol at Boron-Doped Diamond Film Electrode

The electrochemical characteristics of multi-component phenolic pollutants, such as phenol （Ph）, hydroquinone （HQ） and 4-nitrophenol （4-NP）, were investigated on boron-doped diamond （BDD） film electrode by differential pulse voltammetry （DPV） technique. A simple and feasible platform was accordingly established for the direct and simultaneous determination of these three phenolic pollutants. Results showed that, Ph, HQ and 4-NP gave obvious oxidation peaks on BDD electrode at the potential of 1.24, 0.76 and 1.52 V, respectively. Each of them displayed good linear relationship between their oxidation peak currents and their corresponding concentrations in a rather wide range coexisting with one or two of the other phenolic pollutants. The detection limits of Ph, HQ and 4-NP were estimated to be as low as 1.82×10^-6, 1.67×10^-6 and 1.44×10^-6 mol·L^-1, respectively. Therefore, a promising direct and simultaneous electrochemical determination method of multi-component phenolic pollutants in wastewater samples was constructed successfully on BDD electrode with advantages being rapid, simple, convenient, sensitive, in situ and inexpensive.     

Electrochemical Degradation of o-Chloronitrobenzene by Three-dimensional Electrodes

Degradation of o-chloronitrobenzene wastewater was experimentally investigated at a three-dimensional electrode(TDE) with granular activated carbon as the particle electrode, graphite as the anode, and stainless steel plate as the cathode. The kinetic model of o-chloronitrobenzene degradation was studied, and the effects of pH, electrolysis time, particle electrode, electrolyte concentration, and initial concentration of the solution on degradation efficiency were investigated to determine the optimal operating conditions. The degradation of o-chloronitrobenzene by oxidation at the TDE was monitored by chemical oxygen demand(COD) measurements, UV-Vis absorption, and high performance liquid chromatography(HPLC). COD degradation by electrochemical degradation followed pseudo-first order kinetics with respect to the concentration of o-chloronitrobenzene solutions. Optimal reaction conditions included 15 g of activated carbon as the particle electrode, 400 mg/L o-chloronitrobenzene solution containing 0.10 mol/L Na₂SO₄, pH=3, and 60 min of electrolysis. The UV-Vis absorption spectra and HPLC results illustrate that the benzene ring in o-chloronitrobenzene was rapidly broken down to form aliphatic substances through electrochemical degradation. COD degradation was approximately 98.5% at optimal conditions.