Analysis of galactoglucomannans from spruce wood by capillary electrophoresis

The aim of this study was to setup a method for detection and quantification of monosaccharide components in technical galactoglucomannas (T-GGM) from spruce wood using capillary zone electrophoresis (CZE). CZE technique was optimised regarding borate buffer concentrations, EOF modifier application, and system pH. Aqueous solution of T-GGM was chemically hydrolysed by sulphuric acid, in an autoclave. In this way obtained monosaccharides were derivatized with 4-amino benzoic acid ethyl ester via reductive amination using sodium cyanoborohydride. The results of the optimisation procedure showed that the borate buffers at lowest concentrations (100 and 200 mM) with acetonitrile addition as EOF modifier gave the optimal measurement results, as it showed sufficient separation at relatively short migration times. The amounts of single monosaccharide components in the T-GGM samples obtained by the optimised CZE procedure were practically the same in comparison to the results of the well established HPLC-anion exchange chromatography. On the basis of this research, it was concluded that the capillary zone electrophoresis is an efficient analytical procedure for the characterisation of galactoglucomannans derived from softwoods.     

Composite films from spruce galactoglucomannans with microfibrillated spruce wood cellulose

Two future wood biorefinery products, spruce galactoglucomannans (GGM) and microfibrillated spruce wood cellulose (MFC), were mixed to form composite films. The films were plasticized with different amounts of glycerol, and the preparation of films was successful even with low glycerol contents. The film properties were studied using optical microscopy and scanning electron microscopy, x-ray diffraction, water sorption, dielectric analysis, moisture scanning dynamic mechanical analysis, and tensile testing. The addition of MFC clearly affected the properties of the films by decreasing the moisture uptake and increasing the relative humidity of softening of the films and by increasing the glass transition temperature, tensile strength, and Young’s modulus of the films. The effect of MFC addition on the tensile properties of films was emphasized at low glycerol contents. The addition of MFC did not affect the degree of crystallinity of GGM in the films, which was between 20 and 25%. MFC can be efficiently used as reinforcement of GGM films to form wood-based composite materials and to prepare GGM-based films and coatings with low plasticizer content.     

Investigation of the lignin isolated fromPhragmites communis by the method of mechanical milling

Summary Two isomeric dihydrofurocoumarins — zosimin and deltoin — have been isolated from the roots ofZosimia absinthifolia, which contain 3.2% of lactones.Khimiya Prirodnykh Soedinenii, Vol. 1, No. 3, pp. 220–223, 1965     

Microwave-assisted extraction of high-molecular-weight hemicelluloses from spruce wood

Microwave-assisted extraction (MAE) at atmospheric pressure has been demonstrated as an efficient technology for the extraction of polymeric hemicelluloses from spruce sawdust. This technology was shown to be more efficient than conventional extraction. MAE leads to a high solubilization of wood and a selective extraction of hemicellulose polymers with high molecular weights. To optimize MAE, different treatment powers (125–573 W) of presoaked spruce sawdust in water and 1 M sodium hydroxide solution for a period of 60 min were tested. The yield of hemicellulose extraction increased with the microwave power in both mediums, but with a clear advantage for presoaked samples in basic medium. The characterization of extracted hemicelluloses has shown high extraction selectivity depending on the medium of impregnation of sawdust before MAE: High-molecular-mass acetylated galactoglucomannans (M_w ∼ 41 kDa) were isolated after presoaking in water and higher molecular mass arabinoglucoronoxylans (M_w ∼ 66 kDa) in basic medium.     

Nitration of sulfate lignin under homogeneous conditions studied by electron spectroscopy

Russian Chemical Bulletin - The nitration of sulfate lignin by nitric acid in an aqueous-dioxane medium under homogeneous conditions was studied. The method proposed makes it possible to synthesize...     

Characterization of milled wood lignin and ethanol organosolv lignin from miscanthus

Ethanol organosolv lignin extracted from Miscanthus × giganteus (using the following conditions: T = 190 °C, t = 60 min, sulfuric acid = 1.2% w/w, EtOH/H₂O = 0.65) and milled wood lignin from Miscanthus × giganteus were subjected to a comprehensive structural characterization by ¹³C, ³¹P NMR, FTIR, UV spectroscopies and size exclusion chromatography. The results showed that Miscanthus lignin is an H/G/S type (4%, 52%, 44% respectively) with ∼0.41 β-O-4 linkage per aromatic ring and contains coumarylate linkages (0.1/Ar). It was shown that during organosolv treatment, cleavage of β-O-4 linkages and of ester bond (acetyl and coumaryl residues) was the major mechanisms of lignin breakdown but the process did not significantly change the core of the lignin structure.     

Thermogravimetric analysis of wood, holocellulose, and lignin from five wood species

Thermogravimetry has been widely applied to the study of wood and cellulose materials. There is a general agreement that decomposition of hemicellulose, cellulose, and ligning take place in a relatively narrow range of temperature, partially overlapping. There is no a definitive demonstration of which thermal feature corresponds to each component. In this study, three hardwood and two softwood species were considered: Castannea sativa, Eucaliptus globulus, Quercus robur, Pinus pinaster, and Pinus sylvestris. Thermogravimetric analysis of wood powder, ethanol-extracted wood, holocellulose, and lignin, obtained from those species revealed some important differences between hardwood and softwood holocelluloses and an important role of the ethanol-extractives, which explain the different behavior observed in both kinds of wood. FTIR spectra obtained from the evolved gases helped to clarify some degradation steps.     

Thermogravimetry on wood powder-filled polyurethane composites derived from lignin

Novel polyurethane (PU) composites whose matrix is derived from lignin, molasses polyol and filler from wood powder were successfully prepared. Two kinds of polyol were mixed 0/100 to 100/0 in seven steps, and filler content was varied from 50 to 100 mass % to polyol content. Decomposition behaviour of PU composites was investigated by thermogravimetry. Apparent density and mechanical properties of the above composites were also measured. Surface texture was observed by scanning electron microscopy. Thermal decomposition of PU composites was found to occur in two stages. The first decomposition observed at 570–580 K (DT _d1, peak temperature of derivative curve) is attributed to the matrix of composites. The second stage decomposition depending on filler content, observed in a temperature range from 590 to 630 K (DT _d2), is attributable to filler homogenously associated with PU matrix. Marked differences were not found, when the kinds of lignin and molasses polyol composition were varied. The above PU composites were found to be thermally stabilised by the introduction of filler.     

Preservation of beech and spruce wood by allyl alcohol-based copolymers

Allyl alcohol (AA), acrylonitrile (AN), methyl methacrylate (MMA), monomers and monomer mixtures AA+AN, AA+MMA were used to conserve and consolidate Beech and Spruce. After impregnation, copolymerisation and polymerisation were accomplished by gamma irradiation. The fine structure of wood+polymer(copolymer) composites was investigated by Scanning Electron Microscopy (SEM). It was observed that copolymer obtained from AA+MMA monomer mixture showed the optimum compatibility. The compressional strength and Brinell Hardness Numbers determined for untreated and treated wood samples indicated that the mechanical strength of wood+copolymer composites was increased. It was found that the mechanical strength of the wood samples containing the AA+MMA copolymer was higher than the others. In the presence of P(AA/MMA), at highest conversion, the compressive strength perpendicular to the fibres in Beech and Spruce increased approximately 100 times. The water uptake capacity of wood+copolymer composites was observed to decrease by more than 50% relative to the original samples, and biodegradation did not take place.