Label-free electrochemical impedance sensing of DNA hybridization based on functionalized graphene sheets

Negative-charge change and conformation transition upon DNA immobilization and hybridization on functionalized graphene sheets were monitored by the EIS technique and adopted as the signal for label-free electrochemical DNA hybridization detection.     

低温热处理制备石墨烯-氧化钴及其超级电容性能

采用简单的水热法制备出功能化石墨烯与CoOOH的复合物,再通过低温热处理得到功能化石墨烯-Co3O4复合材料;采用扫描电子显微镜分析了样品的形貌;测定了其电化学性能和氮气吸脱附行为.结果表明,Co3O4粒子很好地负载在石墨烯片层之间和表面;形成的复合物具有纳米孔道结构,这些纳米孔道结构有利于电解液离子的传输;而石墨烯良好的导电性有利于电子传递和提高Co3O4粒子的电容贡献值.与此同时,复合物在充放电电流密度为1A/g时的电容达320F/g,表现出优异的超电容性能.     

Multifunctional elastomer nanocomposites with functionalized graphene single sheets

We demonstrate the use of functionalized graphene sheets (FGSs) as multifunctional nanofillers to improve mechanical properties, lower gas permeability, and impart electrical conductivity for several distinct elastomers. FGS consists mainly of single sheets of crumbled graphene containing oxygen functional groups and is produced by the thermal exfoliation of oxidized graphite (GO). The present investigation includes composites of FGS and three elastomers: natural rubber (NR), styrene–butadiene rubber, and polydimethylsiloxane (PDMS). All of these elastomers show similar and significant improvements in mechanical properties with FGS, indicating that the mechanism of property improvement is inherent to the FGS and not simply a function of chemical crosslinking. The decrease in gas permeability is attributed to the high aspect ratio of the FGS sheets. This creates a tortuous path mechanism of gas diffusion; fitting the permeability data to the Nielsen model yields an aspect ratio of ～1000 for the FGS. Electrical conductivity is demonstrated at FGS loadings as low as 0.08% in PDMS and reaches 0.3 S/m at 4 wt % loading in NR. This combination of functionalities imparted by FGS is shown to result from its high aspect ratio and carbon‐based structure. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Flexible graphene films via the filtration of water-soluble noncovalent functionalized graphene sheets

Flexible graphene films were prepared by the filtration of water-soluble noncovalently functionalized graphene sheets with pyrenebutyrate. The work presented here will not only open a new way for preparing water-soluble graphene dispersions but also provide a general route for fabricating conducting films based on graphene.     

Synthesis and electrochemical properties of crown ether functionalized coumarin substituted cobalt and copper phthalocyanines

The synthesis of novel 6,7-[15-crown-5]-3-[p-(3,4-dicyanophenoxy)phenyl]coumarin (1)/6,7-[15-crown-5]-3-[p-(2,3-dicyanophenoxy)phenyl]coumarin (2) and their peripherally/non-peripherally cobalt and copper phthalocyanine complexes (3-6) have been prepared and characterized by elementel analysis, ¹H-NMR, MALDI-TOF, FT-IR and UV-Vis spectral data. Fluorescence intensity changes of compound 1 and 2 have been determined by addition of Na⁺ or K⁺ ions at 25 °C in THF. The effect of substitution type on the redox and aggregation behaviour of the compounds was investigated by voltammetry and in situ spectroelectrochemistry.     

Photoluminescence and electrochemical investigation of curcumin-reduced graphene oxide sheets

This paper reports on a novel low-temperature method for preparing curcumin-reduced graphene oxide (Cur-rGO) from graphene oxide (GO) and investigates their cyclic voltammetry (CV) and photoluminescence (PL) properties. GO sheets were synthesized using modified Hummers’ method and then were chemically reduced using polyphenol curcumin into graphene sheets. Atomic force microscopy, transmission electron microscopy and x-ray photoelectron spectroscopy were used to confirm the formation of Cur-rGO and revealed their functionalization with polyphenol curcumin. The electrochemical and optical properties of the Cur-rGO sheets were investigated using CV and PL spectroscopy. According to the PL and CV characterization for the Cur-rGO sheets, charges and resonant energy were transferred from curcumin molecules to the GO sheets’ surfaces. This arises from the bonding of the fluorescence curcumin molecules to the Cur-rGO surfaces, through π–π stacking of their aromatic rings. It should be noted that curcumin molecules act as electron donors, suppressing the fluorescence of the GO sheets while improving their electrochemical activities.     

Wavy graphene sheets from electrochemical sewing of corannulene

The presence of non-hexagonal rings in the honeycomb carbon arrangement of graphene produces rippled graphene layers with valuable chemical and physical properties. In principle, a bottom-up approach to introducing distortion from planarity of a graphene sheet can be achieved by careful insertion of curved polyaromatic hydrocarbons during the growth of the lattice. Corannulene, the archetype of such non-planar polyaromatic hydrocarbons, can act as an ideal wrinkling motif in 2D carbon nanostructures. Herein we report an electrochemical bottom-up method to obtain egg-box shaped nanographene structures through a polycondensation of corannulene that produces a new conducting layered material. Characterization of this new polymeric material by electrochemistry, spectroscopy, electron microscopy (SEM and TEM), scanning probe microscopy, and laser desorption-ionization time of flight mass spectrometry provides strong evidence that the anodic polymerization of corannulene, combined with electrochemically induced oxidative cyclodehydrogenations (Scholl reactions), leads to polycorannulene with a wavy graphene-like structure.

A bottom-up synthesis of wavy graphene structures obtained through an anodic polymerization process, combined with an electrochemically triggered oxidative cyclodehydrogenation, of the bowl-shaped polyaromatic hydrocarbon corannulene.     

Synthesis of substituted methyl aryl ketone pyrimidinyloximes and their reactions with nucleophiles

Chloropyrimidines react readily with the sodium salts of alkyl aryl ketoximes to give acetophenone O-(2,4-dimethylpyrimidin-6-yl)- and O-(4,6-dimethylpyrimidin-2-yl)oximes, the oximino-groups in which readily undergo nucleophilic substitution.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 12, pp. 1644–1648, December, 1989.     

芳环取代的俘精酸酐的合成及光致变色反应研究

本文报道四个芳环取代的俘精酸酐:2-亚异丙基-3-[1-(4-甲氧苯基)-亚乙基]-丁二酸酐(BF1); 2-亚异丁基-3-[1-(4-甲氧苯基)-亚乙基]-丁二酸酐(BF2);2-亚异丙基-3-[1-(α-萘基)-亚乙基]-丁二酸酐(NF1); 2-亚异丙基-3-[1-(β-萘基)-亚乙基]-丁二酸酐(NF2)的合成及其光致变色性质。测定了它们在不同溶剂中光致变色前后的吸收光谱。利用纳秒级激光闪光光解技术研究了它们的光致变色过程, 并讨论了其光致变色机理。结果表明, 这类芳环取代的俘精酸酐的光致环合反应是经过激发单重态进行的快速过程。     

Synthesis of substituted aryl enol ethers

A facile route toward substituted aryl diarylvinyl ethers 4 is developed from CuI-mediated cross-coupling reaction of substituted phenols 2 with diarylvinyl bromides 3 in the presence of various bidentate-based ligands in DMF. Skeleton 3 is prepared by Yan’s bromomethylenation of diarylketones 1 with CHBr₃–TiCl₄–Mg in the co-solvent of DME and CH₂Cl₂. The synthetic route obtains moderate yields from the one-step operation and the key structure of 4k is confirmed by X-ray crystallographic analysis. The CADD docking experiments of 4k have been included.     

Preparation of substituted rare-earth metal diphthalocyanine complexes and study of their electrochemical behavior

Rare-earth metal diphthalocyanine complexes with R substituents, R₈Pc₂MH (where Pc=phthalocyanine; R=propoxy, t-butyl; M=Er, Lu), were prepared. Their films on basal plane pyrolytic graphite and on indium-tin oxide Nesa glass electrodes in several aqueous electrolytes were investigated by voltammetric analysis and in situ electronic absorption spectroscopy at controlled potentials. These modified electrodes showed multi-color electrochromic behavior as a result of multi-step redox reaction. The film color turned from original green through orange to red in an oxidation process, and through dark blue to purplish in a reduction process.     

Direct electrochemical non-enzymatic assay of glucose using functionalized graphene

A non-enzymatic amperometric sensor is developed based on the graphite electrode modified with functionalized graphene for the determination of β, d (+)-glucose. Cyclic voltammetry and electrochemical impedance spectroscopy techniques are used to study the behavior. Atomic force microscopy was used to study the surface topography of the working electrode before and after its modification. The sensor enabled the direct electrochemical oxidation of β, d (+)-glucose in alkaline medium and responded linearly to the analyte over the range from 0.5?×?10^?3 to 7.5?×?10^?3?M with a limit of detection of 10?μM. The sensor is found to exhibit a better sensitivity of 28.4?μA?mM^?1?cm^?2, good stability, and shelf life. The sensitivity of the sensor to β, d (+)-glucose was not affected by the commonly co-existing interfering substances such as l-ascorbic acid, dopamine, uric acid, and acetaminophen.     

A new family of supramolecular multiferrocenyl rhomboids:Synthesis,characterization,and their electrochemical behavior

Two novel,supramolecular,multiferrocenyl rhomboids 5 and 6 have been successfully constructed from newly designed 60 ferrocenyl donor precursor 1 via coordination-driven self-assembly.The structures of all multiferrocenyl rhomboids were characterized by multinuclear NMR(¹H and ³¹P),CSI-TOF-MS, and PM6 semi-empirical molecular simulation,and their electrochemical behaviors have been investigated.     

Synthesis of substituted aryl amidines from aminoacetonitriles

Aryl aminoacetonitriles are oxidized by NiO₂-H₂O or MnO₂ in the presence of a wide range of NH₂-containing compounds to afford aryl amidines, presumably via iminium intermediates. A ‘one-pot’ procedure for the preparation of heteroaryl amidines from N-containing heteroaryl halides through a process comprising sequential S_NAr substitution and oxidation has also been developed.     

Synthesis, electropolymerization and electrochemical characterization of some new acrylate substituted thiophene derivatives

In this work, three new acrylate substituted thiophene monomers, (3-thienyl) methylacrylate, 6-(3-thienyl)methoxy-hexylacrylate and 11-(3-thienyl)methoxy-undecylacrylate were synthesized and electropolymerized. Electrochemical polymerisation by a potential step technique leads to the formation of an electroactive film on a Pt electrode in each case. The polymerization involves evidently only the thiophene ring, as no sign of polyacrylate formation could be detected. The oxidation of each polymer was studied by in situ external reflectance FTIR spectroscopy, which showed several bands assigned to (bi)polaron type charge carriers in the region 1500–1000 cm⁻¹. The evolution of the conductivity was studied in situ by the contact electric resistance technique. The conductivity of poly(3-thienyl methacrylate) was found to be higher in aqueous solutions than in acetonitrile. The surface of poly((3-thienyl) methacrylate) was found to have a granular structure observed for many polythiophenes, as studied by atomic force microscopy (AFM).     

Synthesis and characterization of organotitanium substituted heteropolytungstosilicates and their biological activity

Tris-, di-(organotitanium) substituted tungstosilicates α、β-[(CpTi)3(SiW9O37)]7- and γ-[(Cp-Ti)2(SiW10O38)]6- were prepared by the reaction of Cp2TiCl2 (Cp = η5-C5H5) with α、β-SiW9O349- (noted α、β-SiW9), γ-SiWO368- (noted γ-SiW10) . The products were characterized by means of elemental analysis, IR, 1H NMR, 183W NMR and polarography. 183W NMR spectra of the complexes support the stoichiometry of the new heteropolyanions and the probable retention of the A-XWg or γ-SiW10 units. And the organotitanium substituted compounds showed promising in vitro antitumor activity in two of human tumor cell lines.     

Synthesis of N-vinyl substituted indoles and their acid-catalyzed behavior

A mild cross-coupling reaction has been used to access several N-vinyl substituted indoles. When treated with acid, these unique enamines produce novel dimeric and trimeric products derived from a preferred protonation reaction at the enamine π-bond.     

Synthesis and electrochemical behavior of novel peripherally and non-peripherally substituted ball-type cobalt phthalocyanine complexes

The syntheses of new ball-type Co(II) phthalocyanines containing 4,4′-(9H-fluorene-9,9-diyl)diphenol substituents at non-peripheral (complex 6) and peripheral (complex 7) positions are presented. These complexes were characterized by UV-Vis, FT-IR, mass spectroscopy and electrochemical methods. Both complexes exhibit metal and ring based redox processes, typical of cobalt phthalocyanine complexes. For 6, the metal based reduction was observed at −0.46 V followed by a ring based reduction at −1.40 V. The metal oxidation for 6 was observed at +0.16 V and the ring based oxidation at +1.05 V. For 7, reductions are easier but the oxidations are more difficult. The metal based reduction for 7 was observed at −0.38 V followed by a ring based reduction at −1.03 V. The metal oxidation for 7 was observed at +0.20 V and the ring based oxidation at +1.35 V.     

Physical properties of silicone foams filled with carbon nanotubes and functionalized graphene sheets

Free-rising silicone foams were made with loading fractions of up to 0.25 wt.-% functionalized graphene sheets (FGS) and up to 1.0 wt.-% carbon nanotubes (CNTs) using hydrogen as blowing agent. Scanning electron microscopy of the samples revealed an open cellular structure and a homogeneous dispersion of both types of nanofillers. The incorporation of nanofiller affected the foaming process and thus the final foam density and cellular structure. Transmission electron microscopy revealed the formation of a CNT network throughout the sample, while FGS presented an exfoliated and intercalated dispersion. The thermal stability of the samples was drastically affected by the presence of both nanofillers. Both nanofillers showed a positive effect on the compressive response of the foams. However, the nanocomposite foams were found to decrease the acoustic absorption with nanofiller content probably due to the variable foam structure and improved stiffness.