Nonlinear properties of polyurethane-urea/multi-wall carbon nanotube composite films

The third-order nonlinear optical properties of polyurethane-urea/multiwalled carbon nanotube composites (PU/MWNT) films with different MWNT concentrations are investigated by the use of the Z-scan technique at a wavelength of 532 nm with a pulse duration of 8 ns. The results reveal that the nonlinear refraction and absorption coefficients are linearly dependent on the MWNT concentration. The negative nonlinear refraction effect is validated from the closed-aperture Z-scan measurements. We find that PU/MWNT films are promising nonlinear optical materials, and the nonlinear coefficients can be controlled.     

Ultrasound and heat enhanced persulfate oxidation activated with Fe0 aggregate for the decolorization of C.I. Direct Red 23

Effluents from the paper printing and textile industries are often heavily contaminated with azo dyes. Azo dyes are difficult to oxidize biologically. This work investigated the decolorization of an azo dye, C.I. Direct Red 23 (DR23), by persulfate (PS) activated with Fe⁰ aggregates (PS/Fe⁰). Ultrasound (US) and heat were used as enhancement tools in the PS oxidation system. Neither US-activated PS nor thermally activated PS was effective in oxidizing DR23. However, the decolorization was significantly enhanced by PS/Fe⁰ combined with US (PS/Fe⁰/US) or heat (PS/Fe⁰/55 °C). Approximately 95% decolorization of 1 × 10⁻⁴ M DR23 was achieved within 15 min in the PS/Fe⁰/US system at an initial pH of 6.0, PS of 5 × 10⁻³ M, Fe⁰ of 0.5 g/L and US irradiation of 106 W/cm² (60 kHz). Complete decolorization was achieved within 10 min in the Fe⁰/PS/55 °C system. The rate of decolorization doubled when US was introduced in the PS/Fe⁰ system during the treatment of different initial dye concentrations. The dependence of dye and true color (ADMI) depletion on PS concentration has been discussed. DR23 was completely degraded based on the disappearance of aromatic groups of UV–vis spectra and the variation of TOC mineralization. The observed pseudo-first-order decolorization rate was substantially enhanced by increasing temperature. The Arrhenius activation energy for the PS activated with Fe⁰ was estimated as 8.98 kcal/mol, implying that higher temperature is beneficial for the DR23 decolorization. The addition of US into the PS/Fe⁰ system did not incur a substantial increase in electricity, whereas the mineralization of DR23 occurred quickly. Thus, both PS/Fe⁰/US and heated PS/Fe⁰ systems are practically feasible for the effective degradation of the direct azo dye in textile wastewater.     

Flow versus permeability weighting in estimating the forward volumetric transfer constant (Ktrans) obtained by DCE-MRI with contrast agents of differing molecular sizes

PurposeTo quantify the differential plasma flow- (F_p-) and permeability surface area product per unit mass of tissue- (PS-) weighting in forward volumetric transfer constant (K^trans) estimates by using a low molecular (Gd-DTPA) versus high molecular (Gadomer) weight contrast agent in dynamic contrast enhanced (DCE) MRI.Materials and methodsDCE MRI was performed using a 7T animal scanner in 14 C57BL/6J mice syngeneic for TRAMP tumors, by administering Gd-DTPA (0.9 kD) in eight mice and Gadomer (35 kD) in the remainder. The acquisition time was 10 min with a sampling rate of one image every 2 s. Pharmacokinetic modeling was performed to obtain K^trans by using Extended Tofts model (ETM). In addition, the adiabatic approximation to the tissue homogeneity (AATH) model was employed to obtain the relative contributions of F_p and PS.ResultsThe K^trans values derived from DCE-MRI with Gd-DTPA showed significant correlations with both PS (r² = 0.64, p = 0.009) and F_p (r² = 0.57, p = 0.016), whereas those with Gadomer were found only significantly correlated with PS (r² = 0.96, p = 0.0003) but not with F_p (r² = 0.34, p = 0.111). A voxel-based analysis showed that K^trans approximated PS (< 30% difference) in 78.3% of perfused tumor volume for Gadomer, but only 37.3% for Gd-DTPA.ConclusionsThe differential contributions of F_p and PS in estimating K^trans values vary with the molecular weight of the contrast agent used. The macromolecular contrast agent resulted in K^trans values that were much less dependent on flow. These findings support the use of macromolecular contrast agents for estimating tumor vessel permeability with DCE-MRI.     

The interfacial effect on ionic conduction of AgI–anatase TiO2 composites

AgI–anatase TiO₂ nanoparticle composites, (x)AgI–(1 ? x)anatase, with different porosities were fabricated over a wide range of 0–1 of AgI content. The electrical conductivity was measured at room temperature as function of AgI content (x) and porosity (p). The conductivity varies considerably with both x and p. In the vicinity of x = 0.4 and p = 0.31, the conductivity attains a maximum (2.5 × 10^? 3 S/cm). The conductivity is enhanced by three orders of magnitude in comparison with that of pristine AgI. The mechanism of the observed conductivity enhancement is discussed in the light of the scanning electron microscope images and X-ray diffraction patterns of the different (x)AgI–(1 ? x)anatase composites.     

Combined effect of blanching and sonication on quality parameters of bottle gourd (Lagenaria siceraria) juice

This study evaluated the combined effect of blanching and sonication treatment on selected quality parameters of bottle gourd juice (BGJ). Bottle gourd cubes were blanched and juice was extracted. Effect of frequency (20–50 kHz), amplitude (50–90%) and time (10–30 min) was also studied on quality parameters like titratable acidity (TA), pH, total soluble solids (TSS), physical stability (PS), ascorbic acid (AA), total phenolics (TP), total carotenoids (TC), browning index (BI), total plate count (TPC) and yeast & mold count (Y&M) of BGJ to derive the level of these parameters. Combined effect of blanching followed by sonication (BFS) showed significant (P ⩽ 0.05) change in all quality parameters except TA. Highest percentage of TSS (5.9 °B), PS (2%), AA (18.99 mg/100 g), TP (1010 mg/100 g) and TC (5.8 mg/100 g) was observed at 70% amplitude, 50 kHz frequency and 20 min. Results suggested 70% amplitude, 50 kHz frequency and 20 min as best treatment conditions for processing of BGJ. Microstructure examination, transmission electron microscopy (TEM) and laser diffraction analysis of BGJ showed significant change in particle size and distribution. Moreover, TEM of blanched and sonicated samples of BGJ also showed significant (P ⩽ 0.05) change in microbial profile.     

Template-free sonochemical synthesis of hierarchically porous NiO microsphere

A novel template-free sonochemical synthesis technique was used to prepare NiO microspheres combined with calcination of NiO_2.45C_0.74N_0.25H_2.90 precursor at 500 °C. The NiO microspheres samples were systematically investigated by the thermograviometric/differential scanning calorimetry (TG/DSC), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), fourier-transformed infrared spectroscopy (FT-IR), Brunnauer–Emmett–Teller (BET) nitrogen adsorption–desorption isotherms, laser particle size analyzer, and ultraviolet–visible spectroscopy (UV–Vis). The morphology of the precursor was retained even after the calcination process, and exhibited hierarchically porous sphericity. The morphology changed over the ultrasonic radiation time, and the shortest reaction time was 70 min, which was much less than 4 h for the mechanical stirring process. The mechanical stirring was difficult to form the complete hierarchically porous microsphere structure. The BET specific surface area and the median diameter of the hierarchically porous NiO microspheres were 103.20 m²/g and 3.436 μm, respectively. The synthesized NiO microspheres were mesoporous materials with a high fraction of macropores. The pores were resulted from the intergranular accumulation. The ultraviolet absorption spectrum showed a broad emission at the center of 475 nm, and the band gap energy was estimated to be 3.63 eV.     

Effect of high intensity ultrasound on the fermentation profile of Lactobacillus sakei in a meat model system

The objective of this study was to investigate the efficacy of high intensity ultrasound on the fermentation profile of Lactobacillus sakei in a meat model system. Ultrasound power level (0–68.5 W) and sonication time (0–9 min) at 20 °C were assessed against the growth of L. sakei using a Microplate reader over a period of 24 h. The L. sakei growth data showed a good fit with the Gompertz model (R² > 0.90; SE < 0.042). Second order polynomial models demonstrated the effect of ultrasonic power and sonication time on the specific growth rate (SGR, μ, h⁻¹) and lag phase (λ, h). A higher SGR and a shorter lag phase were observed at low power (2.99 W for 5 min) compared to control. Conversely, a decrease (p < 0.05) in SGR with an increase in lag phase was observed with an increase in ultrasonic power level. Cell-free extracts obtained after 24 h fermentation of ultrasound treated samples showed antimicrobial activity against Staphylococcus aureus, Listeria monocytogenes, Escherichia coli and Salmonella typhimurium at lower concentrations compared to control. No significant difference (p < 0.05) among treatments was observed for lactic acid content after a 24 h fermentation period. This study showed that both stimulation and retardation of L. sakei is possible, depending on the ultrasonic power and sonication time employed. Hence, fermentation process involving probiotics to develop functional food products can be tailored by selection of ultrasound processing parameters.     

Electrical conductivity of (Ba0.3Sr0.2La0.5)(In1−xFex)O3−δ

We have synthesized the perovskite oxides of the (Ba_0.3Sr_0.2La_0.5)(In_1−xFe_x)O_3−δ system and measured the total electrical conductivity as a function of temperature and oxygen partial pressure. It was found that the single-phase composition region extended from x = 0.0 to x = 1.0, and that the Fe valence increased from 3.06 to 3.50 in that region. The electrical conductivity was semiconducting from x = 0.0 to x = 0.40 and metallic from x = 0.50 to x = 1.0. The total electrical conductivity at 800 °C also increased with the Fe content and achieved a maximum value of 140 (S/cm) at x = 1.0. From the dependence of the electrical conductivity on the oxygen partial pressure, we conclude that above x = 0.50, the majority carriers are holes. The estimated hole conductivity increased exponentially with the amount of Fe⁴⁺ cation present. The oxide ion conductivity was dependent on the oxygen vacancy content.     

Preparation and characterization of low density polystyrene/TiO2 core–shell particles for electronic paper application

In order to reduce the density mismatch between TiO₂ and the low dielectric medium and improve the dispersion stability of the electrophoretic particles in the low dielectric medium for electrophoretic display application, polystyrene/titanium dioxide (PS/TiO₂) core–shell particles were prepared via in-situ sol–gel method by depositing TiO₂ on the PS particle which was positively charged with 2-(methacryloyloxy)ehyl trimethylammonium chloride (DMC). The morphology and average particle size of PS/TiO₂ core–shell particles were observed by transmission electron microscopy (TEM), scanning electron microscope (SEM) and particle size analyzer. It was found that density of PS/TiO₂ core–shell particles were reduced obviously and the particles can suspend in the low dielectric medium of low density. The PS/TiO₂ core–shell particles can endure ultrasonic treatment because of the interaction between TiO₂ and PS. Zeta potential and electrophoretic mobility of the fabricated core–shell particles in a low dielectric medium with charge control agent was measured to be −44.3 mV and −6.07 × 10⁻⁶ cm²/Vs, respectively, which presents potential in electronic paper application.     

Shelf life,physicochemical, microbiological and antioxidant properties of purple cactus pear (Opuntia ficus indica) juice after thermoultrasound treatment

The objective of this study was to evaluate changes in color, betalain content, browning index, viscosity, physical stability, microbiological growth, antioxidant content and antioxidant activity of purple cactus pear juice during storage after thermoultrasonication at 80% amplitude level for 15 and 25 min in comparison with pasteurized juice. Thermoultrasound treatment for 25 min increased color stability and viscosity compared to treatment for 15 min (6.83 and 6.72 MPa, respectively), but this last parameter was significantly lower (p < 0.05) compared to the control and pasteurized juices (22.47 and 26.32 MPa, respectively). Experimental treatment reduced significantly (p < 0.05) sediment solids in juices. Total plate counts decreased from the first day of storage exhibiting values of 1.38 and 1.43 log CFU/mL, for 15 and 25 min treatment, respectively. Compared to the control, both treatments reduced enterobacteria counts (1.54 log CFU/mL), and compared to pasteurized juice decreased pectinmethylesterase activity (3.76 and 3.82 UPE/mL), maintained high values of ascorbic acid (252.05 and 257.18 mg AA/L) and antioxidant activity (by ABTS: 124.8 and 115.6 mg VCEAC/100 mL; and DPPH: 3114.2 and 2757.1 μmol TE/L). During storage thermoultrasonicated juices had a minimum increase in pectinmethylesterase activity (from day 14), and exhibited similar total plate counts to pasteurized juice. An increase of phenolic content was observed after 14 days of storage, particularly for treatment at 80%, 25 min, and an increase in antioxidant activity (ABTS, DPPH) by the end of storage.     

Effect of Fe doping on the structural and gas sensing properties of ZnO porous microspheres

Fe-doped ZnO porous microspheres composed of nanosheets were prepared by a simple hydrothermal method combined with post-annealing, and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), Brunauer–Emmett–Teller N₂ adsorption–desorption measurements and photoluminescence (PL) spectra. In this paper we report Fe doping induced modifications in the structural, photoluminescence and gas sensing behavior of ZnO porous microspheres. Our results show that the crystallite size decreases and specific surface area increases with the increase of Fe doping concentration. The PL spectra indicate that the 4 mol% Fe-doped ZnO has higher ratio of donor (V_O and Zn_i) to acceptor (V_Zn) than undoped ZnO. The 4 mol% Fe-doped ZnO sample shows the highest response value to ppb-level n-butanol at 300 °C, and the detected limit of n-butanol is below 10 ppb. In addition, the 4 mol% Fe -doped ZnO sample exhibits good selectivity to n-butanol. The superior sensing properties of the Fe-doped porous ZnO microspheres are contributed to higher donor defects contents combined with larger specific surface area.     

Flux pinning and superconducting properties of melt-textured NEG-123 superconductor with TiO2 addition

We studied the effect of TiO₂ doping on flux pinning and superconducting properties of a melt-grown (Nd_0.33Eu_0.33Gd_0.33) Ba₂Cu₃O_y + 35 mol% Gd₂BaCuO₅ (70 nm in size) composite (NEG-123) processed in Ar–1% O₂ atmosphere. As indicated by similar, sharp superconducting transitions, the small quantities of TiO₂ used in our experiments did not deteriorate superconducting properties of the NEG material. Transmission electron microscopy (TEM) analysis found 20–50 nm Ti-based particles in the NEG-123 matrix. However, we have not observed the clouds of <10 nm sized particles in the NEG-123 matrix, as in the case of recently reported NEG-123 composites doped by Mo and Nb nanoparticles. Nevertheless, quite a good J_c–B performance in the 0.1 mol% Ti-doped sample, namely 550 kA/cm² at the self-field and at the secondary peak field (4.5 T) was achieved at 65 K, while 320 kA/cm² was obtained at zero-field at 77 K, and 50 kA/cm² at 90.2 K. The pinning effectiveness decreased with increasing Ti content above 0.2 mol%. The analysis of the pinning force showed that higher concentration of Ti (>0.2 mol%) increased the amount of normal pins (δl pinning), indicated by the Fp(h) peak shift from h = 0.42–0.36. The maximum pinning effect in a broad field range could be achieved by optimizing Ti content and adding sub-micron Gd-211 particles.     

Combined of ultrasound irradiation with high hydrostatic pressure (US/HHP) as a new method to improve immobilization of dextranase onto alginate gel

In this research work, dextranase was immobilized onto calcium alginate beads by the combination of ultrasonic irradiation and high hydrostatic pressure (US/HHP) treatments. Effects of US/HHP treatments on loading efficiency and immobilization yield of dextranase enzyme onto calcium alginate beads were investigated. Furthermore, the activities of immobilized enzymes prepared with and without US/HHP treatments and that prepared with ultrasonic irradiation (US) and high hydrostatic pressure (HHP), as a function of pH, temperature, recyclability and enzyme kinetic parameters, were compared with that for free enzyme. The maximum loading efficiency and the immobilization yield were observed when the immobilized dextranase was prepared with US (40 W at 25 kHz for 15 min) combined with HHP (400 MPa for 15 min), under which the loading efficiency and the immobilization yield increased by 88.92% and 80.86%, respectively, compared to immobilized enzymes prepared without US/HHP treatment. On the other hand, immobilized enzyme prepared with US/HHP treatment showed V_max, K_M, catalytic and specificity constants values higher than that for the immobilized enzyme prepared with HHP treatment, indicated that, this new US/HHP method improved the catalytic kinetics activity of immobilized dextranase at all the reaction conditions studied. Compared to immobilized enzyme prepared either with US or HHP, the immobilized enzymes prepared with US/HHP method exhibited a higher: pH optimum, optimal reaction temperature, thermal stability and recyclability, and lower activation energy, which, illustrating the effectiveness of the US/HHP method. These results indicated that, the combination of US and HHP treatments could be an effective method for improving the immobilization of enzymes in polymers.     

Electronic property and structure of double-doping Y1−2xPrxCaxBa2Cu3O7−δ with 0 ⩽ x ⩽ 0.14

Equal amount Pr and Ca double-doping Y_1?2xPr_xCa_xBa₂Cu₃O_7?δ with 0 ? x ? 0.14 have been investigated by X-ray diffraction, resistivity, and X-ray photoemission spectroscopy (XPS). The deviation of the linearly decreasing of T_c vs. x curve was observed when x < 0.10. The resistivity and the temperature coefficient of resistivity also exhibit abnormal behaviors around x = 0.10. It is revealed that the conductivity behavior of Y_1?2xPr_xCa_xBa₂Cu₃O_7?δ with low Pr content (x < 0.10) is different from that of the relative high Pr content (x > 0.10), which suggests a change of Pr valence with the Pr content. XPS measurement shows that the relative amount of Pr³⁺ and Pr⁴⁺ is closely related to the total Pr content x. The valence of Pr is close to +3 when x < 0.10 and increases towards +4 when x > 0.10, which implies a different mechanism for depression of superconductivity of Pr content x < 0.10 from that of Pr content x > 0.10 in Pr doping Y-123.     

Ferromagnetism in Zn1−xCrxTe (x = 0.05, 0.15) films grown on GaAs(1 0 0) substrate

Zn_1−xCr_xTe (x = 0.05, 0.15) films were grown on GaAs(1 0 0) substrate by thermal evaporation method. X-ray diffraction analysis showed the presence of ZnCrTe phase without any secondary phase. The surface was analyzed by high resolution magnetic force microscope and profile measurements showed orientation of magnetic domains in the range of 0.5–2 nm with increase of Cr content. Magnetic moment–magnetic field measurements showed a characteristic hysteresis loop even at room temperature. The Curie temperature was estimated to be greater than 300 K. From the electron spin resonance spectra, the valence state of Cr in ZnTe was found to be +2 with d² electronic configuration. Hall effect study was done at room temperature and the result showed the presence of p-type charge carriers and hole concentration was found to increase from 5.95 × 10¹² to 6.7 × 10¹² m⁻³ when Cr content increases. We deduce the origin of ferromagnetic behavior based on the observed experimental results.     

Development of perovskite and phase transition in lead cobalt niobate modified lead zirconate titanate system

Ferroelectric lead zirconate titanate–lead cobalt niobate ceramics with the formula (1 − x)Pb(Zr_1/2Ti_1/2)O₃–xPb(Co_1/3Nb_2/3)O₃ where x = 0.0–0.5 were fabricated using a high temperature solid-state reaction method. The formation process, the structure and homogeneity of the obtained powders have been investigated by X-ray diffraction method as well as the simultaneous thermal analysis of both differential thermal analysis (DTA) and thermogravimetry analysis (TGA). It was observed that for the binary system (1 − x)Pb(Zr_1/2Ti_1/2)O₃–xPb(Co_1/3Nb_2/3)O₃, the change in the calcination temperature is approximately linear with respect to the PCoN content in the range x = 0.0–0.5. In addition, X-ray diffraction indicated a phase transformation from a tetragonal to a pseudo-cubic phase when the fraction of PCoN was increased. The dielectric permittivity is remarkably increased by increasing PCoN concentration. The maximum value of remnant polarization P_r (25.3 μC/cm²) was obtained for the 0.5PZT–0.5PCoN ceramic.     

Thermodynamics and kinetics of CO and benzene adsorption on Pt(111) studied with pulsed molecular beams and microcalorimetry

The adsorption and desorption of the system CO/Pt(111) and C₆H₆/Pt(111) at 300 K has been investigated with a pulsed molecular beam method in combination with a microcalorimeter. For benzene the sticking probability has been measured in dependence of the coverage θ. For coverages θ > 0.8 transient adsorption is observed. From an analysis of the time-dependence of the molecular beam pulses the rate constant for desorption is determined to be 5.6 s^? 1. With a precursor-mediated kinetic adsorption model this allows to obtain also the hopping rate constant of 95.5 s^? 1. The measured adsorption enthalpies could be best described by (199 ? 77θ ? 51θ²) kJ/mol, in good agreement with the literature values. For CO on Pt(111) also transient adsorption has been observed for θ > 0.95 at 300 K. The kinetic analysis yields rate constants for desorption and hopping of 20 s^?1 and 51 s^?1, respectively. The heats of adsorption show a linear dependence on coverage (131 ? 38θ) kJ/mol between 0 ≤ θ ≤ 0.3, which is consistent with the desorption data from the literature. For higher coverage (up to θ = 0.9ML) a slope of ?63 kJ/mol describes the decrease of the differential heat of adsorption best. This result is only compatible with desorption experiments, if the pre-exponential factor decreases strongly at higher coverage. We found good agreement with recent quantum chemical calculations made for (θ = 0.5ML).     

Experimental investigation of flame spreading over pure methane hydrate in a laminar boundary layer

Flame spreading over pure methane hydrate in a laminar boundary layer is investigated experimentally. The free stream velocity (U_∞) was set constant at 0.4 m/s and the surface temperature of the hydrate at the ignition (T_s) was varied between ?10 and ?80 °C. Hydrate particle sizes were smaller than 0.5 mm. Two types of flame spreading were observed; “low speed flame spreading” and “high speed flame spreading”. The low speed flame spreading was observed at low temperature conditions (T_s = ?80 to ?60 °C) and temperatures in which anomalous self-preservation took place (T_s = ?30 to ?10 °C). In this case, the heat transfer from the leading flame edge to the hydrate surface plays a key role for flame spreading. The high speed flame spreading was observed when T_s = ?50 and ?40 °C. At these temperatures, the dissociation of hydrate took place and the methane gas was released from the hydrate to form a thin mixed layer of methane and air with a high concentration gradient over the hydrate. The leading flame edge spread in this premixed gas at a spread speed much higher than laminar burning velocity, mainly due to the effect of burnt gas expansion.     

Studies on growth morphology,UV absorbance and luminescence properties of sulphur doped ZnO nanopowders synthesized by the application of ultrasound with varying input power

Sulphur doped ZnO nanopowders have been prepared by sonochemical method in continuous (CS) and pulsed (PS) modes. Precipitation time was found to vary with input power of applied ultrasound. X-ray diffraction studies show the formation hexagonal wurtzite phase of nano ZnO but variation in size, strain and lattice parameters was observed in the samples synthesized through CS and PS modes with different input power. Surface morphology of the samples changed significantly with input power of the pulse as observed from scanning electron microscopic results. Well defined and c-axis oriented nanorods and multipodes were observed with power setting of 187.5 W whereas in all other cases no definite morphology was observed. UV absorption studies show higher value of absorbance for ZnO:S. Further, the absorption band becomes sharp for the samples prepared with power setting of 225 W. PL spectra show several bands due to different transitions in the region of 400–780 nm which have been explained in the light of excitonic and defect induced transitions in ZnO.     

Structure and electrochemical properties of Sm0.5Sr0.5Co1 − xFexO3 − δ cathodes for solid oxide fuel cells

Crystal structure, thermal expansion coefficient, electrical conductivity and cathodic polarization of compositions in the system Sm_0.5Sr_0.5Co_1 − xFe_xO_3 − δ with 0 ≤ x ≤ 0.9 were studied as function of Co / Fe ratio and temperature, in air. Two phases, including an Orthorhombic symmetry for 0 ≤ x ≤ 0.4 and a cubic symmetry for 0.5 ≤ x ≤ 0.9, were observed in samples of Sm_0.5Sr_0.5Co_1 − xFe_xO_3 − δ at room temperature. The adjustment of thermal expansion coefficient (TEC) to electrolyte, which is one of the main problems of SSC, could be achieved to lower TEC values with more Fe substitution. High electrical conductivity above 100 S/cm at 800 °C was obtained for all specimens, so they could be good conductors as cathodes of IT-SOFC. The polarization behavior of SSCF as a function of Fe content was evaluated by means of AC impedance using LSGM electrolyte. It was discovered that the Area Specific Resistance (ASR) of SSCF increased as the amount of substitution of Fe for Co increased. When the amount of Fe reached to 0.4, the highest ASR was obtained and then the resistance started decreasing above that. The electrode with a composition of Sm_0.5Sr_0.5Co_0.2Fe_0.8O_3 − δ showed high catalytic activity for oxygen reduction operating at temperature ranging from 700 to 800 °C.