One-step hydrothermal synthesis of LiMn2O4 cathode materials for rechargeable lithium batteries

LiMn₂O₄ cathode materials with high discharge capacity and good cyclic stability were prepared by a simple one-step hydrothermal treatment of KMnO₄, aniline and LiOH solutions at 120–180 °C for 24 h. The aniline/KMnO₄ molar ratio (R) and hydrothermal temperature exhibited an obvious influence on the component and phase structures of the resulting product. The precursor KMnO₄ was firstly reduced to birnessite when R was less than 0.2:1 at 120–150 °C. Pure-phased LiMn₂O₄ was formed when R was 0.2:1, and the LiMn₂O₄ was further reduced to Mn₃O₄ when R was kept in the range of 0.2–0.3 at 120–150 °C. Moreover, LiMn₂O₄ was fabricated when R was 0.15:1 at 180 °C. Octahedron-like LiMn₂O₄ about 300 nm was prepared at 120 °C, and particle size decreased with an increase in hydrothermal temperature. Especially, LiMn₂O₄ synthesized at 150 °C exhibited the best electrochemical performance with the highest initial discharge capacity of 127.4 mAh g⁻¹ and cycling capacity of 106.1 mAh g⁻¹ after 100 cycles. The high discharge capacity and cycling stability of the as-prepared LiMn₂O₄ cathode for rechargeable lithium batteries were ascribed to the appropriate particle size and larger cell volume.     

Morphology-controllable synthesis of LiMn2O4 particles as cathode materials of lithium batteries

We reported a new method for the preparation of morphology-controllable LiMn₂O₄ particles. In this method, dimension-different MnO₂ nanowires synthesized hydrothermally by adjusting the reaction temperature were used as the precursor. The morphology and structure of the resulting products were characterized with scanning electron microscope and X-ray diffraction, and the performances of the prepared LiMn₂O₄ samples as cathode material of lithium batteries were investigated by cyclic voltammetry and galvanostatic charge/discharge test. The results indicate that the morphology of LiMn₂O₄ transforms from tridimensional particle (TP) to unidimensional rod (UR) through quadrate lamina (QL) with increasing the diameter and length of MnO₂ nanowires. Although the cyclic stabilities of LiMn₂O₄-TP, LiMn₂O₄-QL, and LiMn₂O₄-UR are very close (the 0.1 C capacity after 50 cycles is 101, 93, and 99 mAh g^?1 at 25 °C, and 84, 78, and 82 mAh g^?1 at 50 °C, respectively), LiMn₂O₄-QL delivers much higher rate capacity (about 70 mAh g^?1 at 5 C and 30 mAh g^?1 at 10 C) than LiMn₂O₄-TP and LiMn₂O₄-UR (about 20 mAh g^?1 at 5 C, 3 mAh g^?1 at 10 C, 25 mAh g^?1 at 5 C, and 3 mAh g^?1 at 10 C).     

Synthesis and characterization of phosphate-modified LiMn2O4 cathode materials for Li-ion battery

<正>LiMn_2O_4 spinel cathode materials were modified with 2 wt.%Li-M-PO_4(M=Co,Ni,Mn) by polyol synthesis method.The phosphate surface-modified LiMn_2O_4 cathode materials were physically characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and energy dispersive X-ray spectroscopy(EDS).The charge-discharge test showed that the cycling and rate capacities of LiMn_2O_4 cathode materials were significantly enhanced by stabilizing the electrode surface with phosphate.     

Template-free solvothermal synthesis of yolk-shell V2O5 microspheres as cathode materials for Li-ion batteries

Uniform yolk-shell V(2)O(5) microspheres were synthesized via a facile template-free solvothermal route and subsequent calcination treatment in air. The resulting cathode materials showed a high specific capacity of 220 mA h g(-1) after 30 cycles and good rate capability.     

Preparation of spherical spinel LiMn2O4 cathode material for lithium ion batteries

A novel process is proposed for synthesis of spinel LiMn₂O₄ with spherical particles from the inexpensive materials MnSO₄, NH₄HCO₃, and NH₃H₂O. The successful preparation started with carefully controlled crystallization of MnCO₃, leading to particles of spherical shape and high tap density. Thermal decomposition of MnCO₃ was investigated by both DTA and TG analysis and XRD analysis of products. A precursor of product, spherical Mn₂O₃, was then obtained by heating MnCO₃. A mixture of Mn₂O₃ and Li₂CO₃ was then sintered to produce LiMn₂O₄ with retention of spherical particle shape. It was found that if lithium was in stoichiometric excess of 5% in the calcination of spinel LiMn₂O₄, the product had the largest initial specific capacity. In this way spherical particles of spinel LiMn₂O₄ were of excellent fluidity and dispersivity, and had a tap density as high as 1.9 g cm^–3 and an initial discharge capacity reaching 125 mAh g^–1. When surface-doped with cobalt in a 0.01 Co/Mn mole ratio, although the initial discharge capacity decreased to 118 mAh g^–1, the 100th cycle capacity retention reached 92.4% at 25°C. Even at 55°C the initial discharge capacity reached 113 mAh g^–1 and the 50th cycle capacity retention was in excess of 83.8%.     

Effects of AgNPs-coating on the electrochemical performance of LiMn2O4 cathode material for lithium-ion batteries

Journal of Solid State Electrochemistry - The Jahn–Teller effect and severe side reactions with liquid electrolyte have been considered as the main obstacles to the further application of...     

Microwave synthesis of Li_2FeSiO_4 cathode materials for lithium-ion batteries

A novel synthetic method of microwave processing to prepare Li_2FeSiO_4 cathode materials is adopted.The Li_2FeSiO_4 cathode material is prepared by mechanical ball-milling and subsequent microwave processing.Olivin-type Li_2FeSiO_4 sample with uniform and fine particle sizes is successfully and fast synthesized by microwave heating at 700℃in 12 min.And the obtained Li_2FeSiO_4 materials show better electrochemical performance and microstructure than those of Li_2FeSiO_4 sample by the conventional solids...     

Polyimide gel polymer electrolyte-nanoencapsulated LiCoO2 cathode materials for high-voltage Li-ion batteries

We demonstrate a novel and facile approach to surface modification of high-voltage charged LiCoO₂, which is based on encapsulating LiCoO₂ by a polyimide (PI) gel polymer electrolyte layer. The PI is introduced onto the LiCoO₂ by thermally curing 4-component (pyromellitic dianhydride/biphenyl dianhydride/phenylenediamine/oxydianiline) polyamic acid. The PI nanoencapsulating layer features the high surface coverage, nanometer thickness, and facile ion transport. These unique characteristics are expected to enable the PI coating layer to effectively suppress the undesirable interfacial reaction of the LiCoO₂ with liquid electrolyte, which plays a key role in noticeably improving the 4.4 V cycle performance and mitigating the vigorous exothermic reaction between the charged LiCoO₂ and liquid electrolyte.     

Effect of MgF2 coating on the electrochemical performance of LiMn2O4 cathode materials

Spinel LiMn₂O₄ cathode materials were coated with 1.0, 3.0 and 5.0?wt.% of MgF₂ by precipitation, followed by heat treatment at 400?°C for 5?h in air. The effects of MgF₂ coating on the structural and electrochemical properties of LiMn₂O₄ cathodes were investigated using XRD, SEM, and electrochemical tests. XRD and SEM results show that no significant bulk structural differences are observed between the coated and pristine LiMn₂O₄. The charge–discharge tests show that the discharge capacity of LiMn₂O₄ decreases slightly, but the cyclability of LiMn₂O₄ is clearly improved when the amount of the MgF₂ coated was increased to 3.0?wt.%. The 3.0?wt.% MgF₂-coated LiMn₂O₄ exhibits capacity retention of 80.1 and 76.7 % after 100 cycles at room temperature (25?°C) and elevated temperature (55?°C) at a rate of 1?C, respectively, much higher than those of the bare LiMn₂O₄ (70.1 and 61.6 %). The improvement of electrochemical performance is attributed to the suppression of Mn dissolution into the electrolyte via the MgF₂ coating layer.     

Template-synthesized LiCoO2, LiMn2O4, and LiNi0.8 Co0.2 O2 nanotubes as the cathode materials of lithium ion batteries

The first point of this work is to synthesize LiCoO2, LiNi0.8 Co0.2 O2, and LiMn2O4 nanotubes with the template of porous anodic aluminum oxide by thermal decomposition of sol-gel precursors. The as-synthesized materials were open-ended nanotubes with uniform shape and size based on the analysis of scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. An "in situ reaction from nanoparticle to nanotube" mechanism was discussed for the formation process of the nanotubes. The second point of this paper is to investigate the electrochemical properties of the as-synthesized nanotubes for the cathode materials of lithium ion batteries. It was found that the nanotube electrodes exhibited better reversibility and higher discharge capacities than that of their nanocrystalline counterparts. The reason for the improved electrochemical performance of the nanotube electrodes was also interpreted.     

Porous ZnCo2O4 nanowires synthesis via sacrificial templates: high-performance anode materials of Li-ion batteries

A simple microemulsion-based method has been developed to synthesize ZnCo(2)(C(2)O(4))(3) nanowires that can be transformed to porous ZnCo(2)O(4) nanowires under annealing conditions. The morphology of porous ZnCo(2)O(4) nanowires can be tuned by the initial ZnCo(2)(C(2)O(4))(3) nanowires and the annealing temperatures. The as-synthesized porous ZnCo(2)O(4) nanowires have been applied as anode materials of Li-ion batteries, which show superior capacity and cycling performance. The porous one-dimensional (1D) nanostructures and large surface area are responsible for the superior performance. Moreover, it is indicated that porous ZnCo(2)O(4) nanowires synthesized at low annealing temperature (500 °C) show larger capacity and better cycling performance than that prepared at high annealing temperature (700 °C), because of their higher porosity and larger surface area.     

LiCoO2/LiNiO2/LiMn2O4材料安全性能的研究

随着锂离子电池的大型化,对电池安全性能的研究显得更为重要。锂离子电池的安全性有不同的测试方法,如进行过充试验和短路试验。在这些安全性试验中,以及在滥用中出现的安全性的问题,大多是由于电池内部温度升高,进而触发了大量放热的副反应[1],引起电池发生爆炸。本文通过对AA     

Review and prospect of layered lithium nickel manganese oxide as cathode materials for Li-ion batteries

Layered structural lithium metal oxides with rhombohedral α-NaFeO₂ crystal structure have been proven to be particularly suitable for application as cathode materials in lithium-ion batteries. Compared with LiCoO₂, lithium nickel manganese oxides are promising, inexpensive, nontoxic, and have high thermal stability; thus, they are extensively studied as alternative cathode electrode materials to the commercial LiCoO₂ electrode. However, a lot of work needs to be done to reduce cost and extend the effective lifetime. In this paper, the development of the layered lithium nickel manganese oxide cathode materials is reviewed from synthesis method, coating, doping to modification, lithium-rich materials, nanostructured materials, and so on, which can make electrochemical performance better. The prospects of lithium nickel manganese oxides as cathode materials for lithium-ion batteries are also looked forward to.     

One-step hydrothermal synthesis of VO2(B) as cathode materials for high-capacity and high-rate Li-ion batteries

Journal of Solid State Electrochemistry - Optimizing and simplifying the preparation process is an imperative route to achieve excellent electrochemical performance. Hence, in this paper, a simple...     

Anion doping in LiCoO2 cathode materials for Li-ion batteries: a first-principles study

Journal of Solid State Electrochemistry - In this work, anion (F, Cl, and S)-doped LiCoO2 cathode materials were systematically investigated by using first-principles calculations. The results show...     

Physicochemical properties of V5+ doped LiCoPO4 as cathode materials for Li-ion batteries

Phase pure olivine type V⁵⁺ doped and un-doped LiCoPO₄ (LiCo_1?xV_xPO₄ & LiCoP_1?xV_xO₄; x = 0.02, 0.04 and 0.06) were synthesized by combustion method. Compound formation temperature and thermal stability of the materials were studied through thermal analysis. X-ray diffraction pattern shows the prepared material possesses an orthorhombic structure with Pnmb space group. Further the functional group and vibrational analysis were carried out by Fourier Transform Infra-red and Raman spectroscopy techniques. The Scanning Electron Micrographs depicts the irregular shaped morphology with particle agglomeration of the pristine and doped LiCoPO₄ materials. The structural variation on addition of dopant on both sites Co²⁺ & P⁵⁺ were revealed from XPS spectra. The electrochemical aspects of these materials were investigated by cyclic voltammetry studies in conjunction with electrochemical impedance spectroscopy and chronoamperommetry measurements to understand the redox reactions and their capacity contribution at higher voltages. The EIS analysis shows that the conductance value was decreased for the vanadium doped samples for both the Co site and P site, which infers that the V⁵⁺ addition doesn’t make any significant enhancement in the electrochemical performance of the LiCoPO₄.     

Research progress on Na3V2(PO4)2F3-based cathode materials for sodium-ion batteries

Sodium-ion batteries (SIBs) have received significant attention in large-scale energy storage due to their low cost and abundant resources. To obtain high-performance SIBs, many intensive studies about electrode materials have been carried out, especially the cathode material. As various types of cathode material for SIBs, a 3D open framework structural Na₃V₂(PO₄)₂F₃ (NVPF) with Na superionic conductor (NASICON) structure is a promising cathode material owing to its high operating potential and high energy density. However, its electrochemical properties are severely limited by the poor electronic conductivity due to the insulated [PO₄] tetrahedral unit. In this review, the challenges and strategies for NVPF are presented, and the synthetic strategy for NVPF is also analyzed in detail. Furthermore, recent developments of modification research to enhance their electrochemical performance are discussed, including designing the crystal structure, adjusting the electrode structure, and optimizing the electrolyte components. Finally, further research and application for future development of NVPF are prospected.     

PVP-functionalized nanometre scale metal oxide coatings for cathode materials: successful application to LiMn2O4 spinel nanoparticles

PVP functionalized metal oxide coatings on spinel nanoparticles demonstrated significantly improved rate characteristics under extensive cycling at 65 degrees C and exhibited over 100% improved capacity retention compared to the bare counterpart.     

Al2O3 coated LiCoO2 as cathode for high-capacity and long-cycling Li-ion batteries

In this study, we fabricated a Al₂O₃ layer coated on the surface of LiCoO₂ by a facile and scale-up sol-gel method. The proper thickness coating can improve the cycling life with the cut-off potential (4.5 V), which capacity retention is~73% after 500 cycles, and enhance the capacity, which shows~180 mAh/g.