Composition and lattice mismatch dependent dielectric constants and optical phonon modes of InAs1−x−ySbxPy quaternary alloys

Based on the pseudopotential formalism under the virtual crystal approximation, the dielectric and lattice vibration properties of zinc-blende InAs_1−x−ySb_xP_y quaternary system under conditions of lattice matching and lattice mismatching to InAs substrates have been investigated. Generally, a good agreement is noticed between our results and the available experimental and theoretical data reported in the literature. The variation of all features of interest versus either the composition parameter x or the lattice mismatch percentage is found to be monotonic and almost linear. The present study provides more opportunities to get diverse high-frequency and static dielectric constants, longitudinal and transversal optical phonon modes and phonon frequency splitting by a proper choice of the composition parameters x and y (0 ⩽ x ⩽ 0.30, 0 ⩽ y ⩽ 0.69) and/or the lattice mismatch percentage.     

Structure and piezoelectric properties of BiFeO3 and Bi0.92Dy0.08FeO3 multiferroics at high temperature

Multiferroic BiFeO₃ and Bi_0.92Dy_0.08FeO₃ ceramics were prepared to study their crystal structures and piezoelectric properties. BiFeO₃ exhibits rhombohedral phase below 810 °C. Although Bi_0.92Dy_0.08FeO₃ ceramic also shows rhombohedral phase at room temperature, it allows the coexistence of rhombohedral phase and orthorhombic phase at 460–650 °C. Both samples have maximum polarizations of >21 μC/cm² and piezoelectric d₃₃ values of ～37 pC/N at room temperature. Their polarized slices show the dielectric anomalies and impedance anomalies because of vibrating resonances below 500 °C, and the thickness vibration electromechanical coupling factor is ～0.6 and ～0.4 for BiFeO₃ and Bi_0.92Dy_0.08FeO₃, respectively. The vibrating resonances confirm piezoelectric responses. Furthermore, samples' impedance and resistance decrease fast with temperature increasing, which screens piezoelectric response above 550 °C.     

Enhanced mangnetoelectric voltage in multiferroic particulate Ni0.83Co0.15Cu0.02Fe1.9O4−δ/PbZr0.52Ti0.48O3 composites – dielectric,piezoelectric and magnetic properties

Multiferroic particulate composites of Ni_0.83Co_0.15Cu_0.02Fe_1.9O_4−δ– NCCF and lead zirconate titanate (PZT) were prepared conventional ceramic method. The generic formulae x NCCF + (1−x) PZT where x = 0.1, 0.2, 0.3, 0.4, 0.5 and 0.6 mole fractions. The presence of two phases in multiferroic was confirmed with XRD technique. The dielectric constant and loss tangent were studied as a function of frequency (100 Hz to 1 M Hz) and temperature (30–500 °C). The piezoelectric coefficient d₃₃ were also studied on these particulate composites. The hysteresis behaviour was studied to understand the magnetic properties such as saturation magnetization (Ms) and magnetic moment (μ_B). The static magnetoelectric (ME) voltage coefficient was measured as a function of dc magnetic bias field. A high value of ME output (3151 mV/Oe.cm) was obtained in the composite containing 50% highly magnetostrictive ferrite component NCCF – 50% highly piezoelectric ferroelectric component PZT. These multiferroic particulate composites are used as phase shifters, magnetic sensors, cables etc.     

Effects of Zr/Ti ratio on dielectric and ferroelectric properties of 0.8Pb(ZrxTi1−x)O3–0.2Pb(Co1/3Nb2/3)O3 ceramics

The influences of Zr/Ti ratio on electrical properties of the 0.8Pb(Zr_xTi_1−x)O₃–0.2Pb(Co_1/3Nb_2/3)O₃ ceramics prepared by a mixed-oxide method (with x = 0.46, 0.48, 0.50, 0.52, and 0.54) have been investigated in order to identify the morphotropic phase boundary composition in this system. With XRD analysis, the crystal structure of dense specimens appeared to change gradually from tetragonal to rhombohedral with increasing Zr content. The dielectric properties measurements showed a maximum dielectric constant at x = 0.50, while the transition temperature decreased with increasing Zr content in the system. Moreover, all ceramics showed diffused phase transition behaviors with a minimum diffusivity at x = 0.50. In addition, the Polarization–Electric field (P–E) hysteresis loops of the ceramic systems also changed significantly with the Zr content. Interestingly, the loop squareness parameter reached maximum around x = 0.50. Other ferroelectric hysteresis parameters showed noticeable change at x = 0.50. These results clearly showed the significance of Zr/Ti ratio in controlling the electrical properties of the PZT–PCN ceramic systems.     

A magnetic study of HoMn6Sn6−xGax single crystals (0.14⩽x⩽1.89)

Single crystals of hexagonal HfFe₆Ge₆-type HoMn₆Sn_6−xGa_x compounds (0.14⩽x⩽1.89) have been obtained by a flux method and studied by magnetisation measurements. All the compounds order ferrimagnetically (308⩽T_c⩽386 K) with moments lying in the (0 0 1) plane and undergo a moment reorientation transition at lower temperatures (156⩽T_SR⩽195 K). At 5 K, the moments are aligned along an intermediate direction (44⩽φ_c⩽50°). These results are discussed and compared with the neutron diffraction results related to the isotypic TmMn₆Sn_6−xGa_x and TbMn₆Sn_6−xGa_x series where a change of the easy direction is observed with increasing gallium contents.     

57Fe Mössbauer spectroscopy and magnetization study of YFexAl12−x (4.4⩽x⩽5)

YFe_xAl_12−x in the composition range 4.4⩽x⩽5 was prepared by induction melting followed by annealing in vacuum at 1270 K. Magnetization data below 150 K show complex magnetic behaviour dependent on applied field, composition and temperature. The transition temperature T_c, corresponding to the main maximum of the magnetization vs. temperature curves and below which magnetic interactions are observed for a significant fraction of the Fe atoms in the Mössbauer spectra, decreases from 180 K for x=4 down to 100 K for 4.2⩽x⩽4.7 and rises again up to 160 K for x=5. The analysis of the spectra obtained at 5 K is consistent with full occupation of the 8f sites by Fe atoms and sharing of the 8j sites by Fe and Al as deduced from the Rietveld analysis of X-ray powder diffraction data. The Mössbauer spectra further show a dependence of magnetic hyperfine fields and isomer shifts on the crystallographic site and on the number of the Fe nearest neighbours similar to that observed in UFe_xAl_12−x (4⩽x⩽6) and RFe_xAl_12−x (R=Y, Lu, x=4, 4.2). The magnetic properties of the UFe_xAl_12−x and YFe_xAl_12−x series are compared and the magnetic interactions between the different Fe sublattices are discussed.     

Determination of the critical indium composition corresponding to the metal–insulator transition in InxGa1−xN (0.06 ⩽ x ⩽ 0.135) layers

The low-temperature conductivity of In_xGa_1−xN alloys (0.06 ⩽ x ⩽ 0.135) is analyzed as a function of indium composition (x). Although our In_xGa_1−xN alloys were on the metallic side of the metal–insulator transition, neither the Kubo-Greenwood nor Born approach were able to describe the transport properties of the In_xGa_1−xN alloys. In addition, all of the In_xGa_1−xN alloys took place below the Ioeffe–Regel regime with their low conductivities. The observed behavior is discussed in the framework of the scaling theory. With decreasing indium composition, a decrease in thermal activation energy is observed. For the metal–insulator transition, the critical indium composition is obtained as x_c = 0.0543 for In_xGa_1−xN alloys.     

Dielectric and piezoelectric properties of (Bi1−x−yNdxNa1−y)0.5BayTiO3 lead-free ceramics

New lead-free (Bi_1−x−yNd_xNa_1−y)_0.5Ba_yTiO₃ ceramics were prepared by a conventional ceramic technique and their dielectric and piezoelectric properties were studied. X-ray diffraction studies reveal that Nd³⁺ and Ba²⁺ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a new solid solution with a pure perovskite structure, and a morphotropic phase boundary (MPB) of rhombohedral and tetragonal phases is formed at 0.04 < y < 0.10. The partial substitutions of Nd³⁺ and Ba²⁺ decrease effectively the coercive field E_c and increase significantly the remanent polarization P_r. Because of lower E_c, larger P_r and the formation of the MPB, the piezoelectric properties of the ceramics are significantly enhanced at x/y = 0.02/0.06: d₃₃ = 150 pC/N and k_p = 30.5%. The ceramics exhibit relaxor characteristic, which is probably resulted from the cation disordering in the 12-fold coordination sites. The depolarization temperature T_d shows a strong compositional dependence and reaches a minimum value at the MPB. The temperature dependences of the ferroelectric and dielectric properties suggest that the ceramics may contain both the polar and non-polar regions near the depolarization temperature T_d, which cause the polarization hysteresis loop become deformed near/above T_d.     

Preparation,characterization and electrical property of Mn-doped ceria-based oxides

Manganese-doped ceria-based oxides, Ce_1−xMn_xO_2−δ (0.05 ≤ x ≤ 0.3) and Ce_1−x−yGd_xMn_yO_2−δ˙ (0.05 ≤ x≤ 0.2, 0.05 ≤ y ≤ 0.25) were synthesized, and crystal phase analysis by XRD and measurements of electrical properties were performed. Solubility limit of Mn in Ce_1−xMn_xO_2−δ˙ seemed to be between 5 mol% and 10 mol% and Mn₃O₄ was the main by-product above the solubility limit in the case of heat treatment at 1300 °C. Judging from the oxygen partial pressure dependence of total conductivity and emf measurements, Ce_1−xMn_xO_2−δ˙ is a single-phase mixed conductor within the composition below the solubility limit, and when the composition of Mn exceeds the solubility limit, it becomes the dual-phase mixed conductor of Ce_1−xMn_xO_2−δ˙ and Mn₃O₄. The doing of Mn in gadlia-doped ceria, Ce_1−x−yGd_xMn_yO_2−δ˙ (0.05 ≤ x ≤ 0.2, 0.05 ≤ y ≤ 0.25), was more difficult than that in CeO₂ presumably due to the preferential reaction between Gd and Mn to give GdMnO₃ to the GDC solid solution formation, and the Mn doping seems not to be so effective in preparing the mixed ionic–electronic conductor based on GDC.     

Band overlap via chemical pressure control in double perovskite (Sr2−xCax)FeMoO6 (0 ⩽ x ⩽ 2.0) with TMR effect

The chemical pressure control in (Sr_2−xCa_x)FeMoO₆ (0 ⩽ x ⩽ 2.0) with double perovskite structure has been investigated systematically. We have performed first-principles total energy and electronic structure calculations for x = 0 and x = 2.0. The increasing Ca content in (Sr_2−xCa_x)FeMoO₆ samples increases the magnetic moment close to the theoretical value due to reduction of Fe/Mo anti-site disorder. An increasing Ca content results in increasing (Fe²⁺ + Mo⁶⁺)/(Fe³⁺ + Mo⁵⁺) band overlap rather than bandwidth changes. This is explained from simple ionic size arguments and is supported by X-ray absorption near edge structure (XANES) spectra and band structure calculations.     

Synthesis and electrical transport properties of Lu2+xTi2−xO7−x/2 oxide-ion conductors

The Lu_2+xTi_2−xO_7−x/2 (x = 0; 0.052; 0.096; 0.286; 0.44; 0.63; 33.3–49 mol% Lu₂O₃) nanoceramics with partly disordered pyrochlore-type structure are prepared by sintering freeze-dried powders obtained by a co-precipitation technique with 1600 °C annealing. Similar to pyrochlore-like compositions in the zirconate system, some of the new titanates are good oxide-ion conductors in air. The new solid-state electrolytes have oxide-ion conductivity in the interval of 1.0 × 10^− 3 – 2.5 × 10^− 3 S/cm at 740 °C in air. This value of conductivity is comparable with that of ZrO₂/Y₂O₃ ceramics. The conductivity of Lu_2+xTi_2−xO_7−x/2 depends on the chemical composition. The highest ionic conductivity is exhibited by nearly stoichiometric Lu_2+xTi_2−xO_7−x/2 (x = 0.096; 35.5 mol% Lu₂O₃) material containing ∼ 4.8 at.% Lu_Ti anti-site defects.     

Correlation between Meyer–Neldel rule and phase separation in Se98−xZn2Inx chalcogenide glasses

The present work reports the observation of Meyer–Neldel rule for the thermally activated crystallization of glassy Se_98−xZn₂In_x (0 ⩽ x ⩽ 10) alloys. We have observed a strong co-relation between the pre-exponential factor K₀ of rate constant K(T) of crystallization and activation energy of crystallization E_c in the present case. This indicates the presence of compensation effect for the non-isothermal crystallization process in the present glassy system, which is explained in terms of phase separation of the present alloys due to flaw bonds of these amorphous solids.     

Effect of Fe doping on the room temperature ferromagnetism in chemically synthesized (In1−xFex)2O3 (0 ⩽ x ⩽ 0.07) magnetic semiconductors

Observation of room temperature ferromagnetism in Fe doped In₂O₃ samples (In_1−xFe_x)₂O₃ (0 ⩽ x ⩽ 0.07) prepared by co-precipitation technique is reported. Lattice parameter obtained from powder X software shows distinct shrinkage of the lattice constant indicating an actual incorporation of Fe ions into the In₂O₃ lattice. X-ray diffraction data measurements show that the entire sample exhibits single phase polycrystalline behavior. SEM micrographs showed the prepared powder was in the range 25–36 nm. SEM EDS mapping showed the presence of Fe and In ions in the Fe doped In₂O₃ sample. The highest remanence magnetization moment (6.624 × 10⁻⁴ emu/g) is reached in the sample with x = 0.03.     

Phase formation and electrical properties of BNLT–BZT lead-free piezoelectric ceramic system

Phase formation study in lead-free piezoelectric ceramics based on lanthanum doped bismuth sodium titanate (Bi_0.4871Na_0.4871La_0.0172TiO₃:BNLT) and zirconium doped barium titanate (BaZr_0.05Ti_0.95O₃:BZT), has been carried out in the system of (1−x)BNLT–xBZT where x = 0.0–1.0, by two-step mixed oxide method. It was observed that the addition of BZT in the BNLT ceramics developed the dielectric and piezoelectric properties of the ceramics with the optimum piezoelectric constant (d₃₃) and dielectric constant (ε_r) at room temperature of about 138 pC/N and 1651, respectively, from the 0.2 BNLT to 0.8 BZT ceramic sample. The Curie temperature (T_C) of this ceramic was found at 295 °C which is 195 °C higher than that of pure BZT ceramics, promising the use of this ceramic in a higher range of temperature.     

Pressure effect on magnetic properties of NdMn2−xFexGe2 (0.1⩽x⩽1.0) series of solid solutions

Temperature and pressure dependence of magnetic properties in the NdMn_2−xFe_xGe₂ series of solid solutions (0.1⩽x⩽1.0) are reported. The (P, T) magnetic phase diagrams are determined on the basis of the AC magnetic susceptibility measured in a weak magnetic field. The measurements were carried out under hydrostatic pressure up to 1.5 GPa in the temperature range 80−430 K. The reported data show that in the studied series of solid solutions, a drastic change in magnetic properties takes place in a narrow dilution parameter range (0.4⩽x⩽0.5). While taking into account the magnetic properties, the studied range of Fe content could be divided into four regions. Only in the case of x=0.3 and 0.4, the external pressure significantly influences the magnetic properties of the samples.     

Effect of doping on cohesive and thermophysical properties of MgB2

The effects of doping Al and Mn on the cohesive and thermophysical properties of MgB₂ have been investigated using a Rigid Ion Model (RIM). The interatomic potential of this model includes contributions from the long-range Coulomb attraction and the short-range overlap repulsion and the van der Waals attraction. This model has been applied to describe the temperature dependence of the specific heat of MgB₂, Mg_1−xAl_xB₂ (x = 0.1–0.9) and Mg_1−xMn_xB₂ (x = 0.01–0.04) in the temperature range 5 K ⩽ T ⩽ 1000 K. The calculated results on cohesive energy (ϕ), Bulk modulus (B_T), molecular force constant (f), Restrahalen frequency (ν₀), Debye temperature (Θ_D) and Gruneisen parameter (γ) are also reported for these materials. Our results on Bulk modulus, Restrahalen frequency and Debye temperature are closer to the available experimental data. The comparison between our calculated and available experimental results on the specific heat at constant volume for MgB₂ and Mg_1−xAl_xB₂ (x = 0.1–0.4), particularly, at lower temperatures has shown almost an excellent agreement. The trend of variation of the specific heat with temperature is more or less similar in pure and doped MgB₂.     

Spectral sensitivity dependencies of backside illuminated planar MCT photodiodes

Spectral sensitivity dependencies of Hg_1−xCd_xTe (0.20 ⩽ x ⩽ 0.25) backside illuminated planar photodiodes were investigated at T = 80 K to study their longwavelength edge features. It was shown that the longwavelength part of these spectral dependencies is mainly formed by the exponential wavelength dependence of the optical transitions. Empirical dependencies of cut-off wavelengths at different values (λ_max, λ_0.5, λ_0.9) were obtained. The influence of the epitaxial layer thickness on the maximum sensitivity position was also studied.     

Characteristics of pulse plated CdxZn1−xSe films

Cd_xZn_1−xSe films (0 ⩽ x ⩽ 1) were deposited for the first time by the pulse plating technique at different duty cycles in the range 6–50% at room temperature from an aqueous bath containing zinc sulphate, cadmium sulphate and selenium oxide. To the author’s knowledge this is the first report on pulse plated Cd_xZn_1−xSe films. The deposition potential was −0.9 V (SCE). The as deposited films exhibited cubic structure. Composition of the films was estimated by Energy Dispersive Analysis of X-ray studies. X-ray photoelectron spectroscopy studies indicated the binding energies corresponding to Zn(2p_3/2), Cd(3d_5/2 and 3d_3/2) and Se(3d_5/2 and 3d_3/2). Optical band gap of the films varied from 1.72 to 2.70 eV as the composition varied from CdSe to ZnSe side. Atomic force microscopy studies indicated grain size in the range of 20–150 nm.     

Electrical and mechanical properties of diluted magnetic semiconductor Zn1−xMnxS nanocrystalline films

Nanostructured Zn_1−xMn_xS films (0 ⩽ x ⩽ 0.25) were deposited on glass substrates by simple resistive thermal evaporation technique. All the films were deposited at 300 K in a vacuum of 2 × 10⁻⁶ m bar. All the films temperature dependence of resistivity revealed semiconducting behaviour of the samples. Hot probe test revealed that all the samples exhibited n-type conductivity. The nanohardness of the films ranges from 4.7 to 9.9 GPa, Young’s modulus value ranging 69.7–94.2 GPa.     

Crystal structure,thermochemical stability,electrical and magnetic properties of the two-phase composites in the La0.8Sr0.2MnO3 ± δ–CeO2 system

Crystal structure, thermochemical stability, transport and magnetic properties of compositions in the (100-x) La_0.8Sr_0.2MnO_3 ± δ xCeO₂ (LSMC) system were studied. All compositions in the LSMC series containing more than 2 mol% CeO₂ were two phase and consisted of the modified perovskite constituent with rhombohedral structure (R3?c) and ceria as a secondary phase with cubic structure (Fm3?m). The presence of both Ce⁴⁺and Ce³⁺ cations in LSMC compositions was revealed by X-ray Photoelectron Spectroscopy (XPS). CeO₂ and compositions in the LSMC series showed good thermochemical stability in air and argon. However, in H₂–Ar atmosphere all LSMC compositions underwent reduction followed by decomposition. Transport and magnetic properties change in a non-linear way with the increase in the CeO₂ content. The LSMC2 composition showed enhanced electronic conductivity and magnetic characteristics. Metallic type conductivity was observed for LSMC compositions with x ≤ 36 mol% CeO₂ in a narrow temperature range of 770–900 °C. A small degree of substitution of Ce into LSM was found to change structural, magnetic and electrical properties.