Effect of optimized aging processing on properties of the sintered Dy-doped Nd–Fe–B permanent magnet

We investigate the effect of the optimized aging processing on magnetism and mechanical property of the sintered Dydoped Nd–Fe–B permanent magnet. The experimental results show that the magnetism, especially intrinsic coercivity, of the optimized aged Dy-doped Nd–Fe–B magnet is more excellent than that of the sintered one, but the former's strength and hardness are lower than that of the latter. It was observed that the optimized aged Dy-doped Nd–Fe–B magnet have more uniform grain size, thinner(Nd, Dy)-rich boundary phase. By means of the EBSD technology, the number of larger angle grain boundaries in the optimized aged Dy-doped Nd–Fe–B magnet is more than that of the sintered one. The reasons for the increased intrinsic coercivity and decreased mechanical properties of the optimized aged Dy-doped Nd–Fe–B magnet are also discussed.     

Effect of irradiation on microstructure and hardening of Cr–Fe–Ni–Mn high-entropy alloy and its strengthened version

ABSTRACT

A single-phase fcc high-entropy alloy (HEA) of 20%Cr–40%Fe–20%Mn–20%Ni composition and its strength with yttrium and zirconium oxides version was irradiated with 1.4?MeV Ar ions at room temperature and mid-range doses from 0.1 to 10 displacements per atom (dpa). Transmission electron microscopy (TEM), scanning transmission electron microscopy with energy dispersive X-ray spectrometry (STEM/EDS) and X-ray diffraction (XRD) were used to characterise the radiation defects and microstructural changes. Nanoindentation was used to measure the ion irradiation effect on hardening. In order to understand the irradiation effects in HEAs and to demonstrate their potential advantages, a comparison was performed with hardening behaviour of 316 austenitic stainless steel irradiated under an identical condition. It was shown that hardness increases with irradiation dose for all the materials studied, but this increase is lower in high-entropy alloys than in stainless steel.     

Effect of Co on the thermal stability and impact toughness of sintered Nd–Fe–B magnets

The effect of Co on the thermal stability and impact toughness of sintered Nd–Fe–B magnets has been investigated. The results showed that the addition of Co decreased the intrinsic coercivity and the temperature coefficient of remanence (α), and increased the temperature coefficient of coercivity (β) for sintered Nd–Fe–B magnets. The impact toughness of sintered Nd–Fe–B magnets with the addition of Co first decreases, reaches a minimum, and then starts to increase. The possible reasons for increasing the temperature coefficients of coercivity (β) for sintered Nd–Fe–B magnets were analyzed, and the relations between the microstructure and impact toughness of sintered Nd–Fe–B magnets were studied.     

Laser processing of bulk Al–12Si alloy: influence of microstructure on thermal properties

The feasibility of enhancing the thermal conductivity of an alloy via microstructural refinement was examined using Al–12%Si alloy as a model material. Al–12Si alloy samples were fabricated at different process parameters using laser engineered net shaping (LENS?) and the effect of microstructural features on the thermal conductivity was studied and compared with conventionally cast alloy. The large difference in melting points and laser light absorptivities of Si and Al as well as the low melt viscosity of Al–12Si alloy resulted in a very small process window to successfully fabricate bulk Al–12Si alloy samples using LENS?. Comparison of microstructural features of laser-processed samples with cast Al–12Si alloy showed significant refinement in eutectic Si for laser processed samples. Microstructural refinement not only improved the thermal conductivity of Al–12Si alloy but also compensated the detrimental effect of porosity on thermal conductivity. The thermal conductivity of cast alloy varied between 82 and 93?W/mK, which is ～21–76% lower than the values exhibited by laser-processed samples in the range 103–153?W/mK. The results of LENS? fabrication, microstructural evolution and thermal properties of Al–12Si alloy bulk structures can be extended to other immiscible alloys and metal matrix composites for a variety of engineering applications.     

Effect of Tb on the intrinsic coercivity and impact toughness of sintered Nd–Dy–Fe–B magnets

The effect of Tb on the coercivity and impact toughness of sintered Nd–Dy–Fe–B magnets has been investigated. The results showed that the addition of Tb enhanced the intrinsic coercivity, reduced the remanence and improved the impact toughness of sintered magnets. The optimum impact toughness of sintered magnets was achieved when 1.0 at% Tb was incorporated. The possible reasons for increasing the intrinsic coercivity and improving impact toughness of sintered magnets were analyzed, and the relations between the microstructure and impact toughness of sintered magnets were studied.     

Effect of the Energy of Krypton Ions on the Structure and Hardening of Ti–Cr–N Coatings

Russian Physics Journal -     

Effect of irradiation and pre-ageing temperature on the mechanical properties of Al–Si alloy

Al–1wt.%Si alloy samples in the solid solution state were irradiated with doses of gamma rays up to 1.75 MGy for 2 h in the temperature range from 423 to 553 K. Induced variations in structure, mechanical and electrical properties were traced by suitable techniques. Observed changes in the measured parameters, internal friction Q ^?1, thermal diffusivity D _th, dynamic elastic modulus Y and resistivity, ρ, were explained in terms of the role and mode of interaction of lattice defects in irradiated and thermally treated samples. Composition inhomogeneity and variations in mass distribution in the matrix were also considered. The structure identification of the samples was carried out by using conventional X-ray diffraction techniques and transmission electron microscopy micrographs.     

Effect of Sn and Al additions on the microstructure and mechanical properties of amorphous Ti–Cu–Zr–Ni alloys

Amorphous Ti–Cu–Zr–Ni alloys with minor addition of Sn and Al were prepared by melt spinning technique.The effects of Sn and Al additions on the microstructures and mechanical properties of glassy ribbons were investigated.The amorphous state of ribbons was confirmed by x-ray diffraction and transmission electron microscopy,where those ribbons with Sn addition exhibited a fully amorphous state.The characteristic temperature indicates that Ti_(45)Cu_(35)Zr_(10)Ni_5Sn_5 alloy has a stronger glass-forming ability,as proven by differential scanning calorimetry.Ti_(45)Cu_(35)Zr_(10)Ni_5Al_5 alloy showed a better hardness of 9.23 GPa and elastic modulus of 127.15 GPa and good wear resistance.Ti_(45)Cu_(35)Zr_(10)Ni_5Sn_5 alloy displayed a pop-in event related to discrete plasticity according to nanoindentation.When the temperature is below 560 K,Ti_(45)Cu_(35)Zr_(10)Ni_5Sn_5 alloy mainly exhibits elasticity.When the temperature rises between 717 K and 743 K,it shows a significant increase in elasticity but decrease in viscoelasticity after the ribbon experiences the main relaxation at 717 K.When the temperature is above 743 K,the ribbon shows viscoplasticity.     

Effect of annealing temperature on the microstructure and optical–electrical properties of Cu–Al–O thin films

We have successfully prepared Cu–Al–O thin films on silicon (100) and quartz substrates by radio frequency (RF) magnetron sputtering method. The as-deposited Cu–Al–O film is amorphous in nature and post-annealing treatment in argon ambience results in crystallization of the films and the formation of CuAlO₂. The annealing temperature plays an important role in the surface morphology, phase constitution and preferred growth orientation of CuAlO₂ phase, thus affecting the properties of the film. The film annealed at 900 °C is mainly composed of CuAlO₂ phase and shows smooth surface morphology with well-defined grain boundaries, thus exhibiting the optimum optical–electrical properties with electrical resistivity being 79.7 Ω·cm at room temperature and optical transmittance being 80% in visible region. The direct optical band gaps of the films are found in the range of 3.3–3.8 eV depending on the annealing temperature.     

Effects of laser power density on the microstructure and microhardness of Ni–Al alloyed layer by pulsed laser irradiation

Laser alloying of Ni–P electroless deposited layer with aluminum substrate was carried out by Nd–YAG pulsed laser. The phase composition and microstructure of the alloyed layers produced by different laser power densities were identified by X-ray diffractionary (XRD), scanning electron microscope (SEM) accompanied by energy dispersion X-ray analysis (EDS) and transmission electron microscope (TEM). Furthermore, the surface roughness of the alloyed layers was characterised by confocal laser scanning microscope (CLSM). The results showed that the characteristic dendritic or lamellar microstructures were observed in the alloyed layers. The phase constituents of the alloyed zones were intermetallic compounds of nickel–aluminum NiAl, Al₃Ni and Al₃Ni₂, as well as some non-equilibrium phases and amorphous phases depending on the employed laser power density. As a result, the microhardness of the alloyed layer with Ni–P amorphous phases formed at laser power density 5.36×10⁹ W/m² reached to HV_0.1 390.     

Mössbauer study of the annealing effect on low‐alloyed steels

Structural analyses of Fe-Cr and Fe-Cr-Ni low‐alloyed steels before and after annealing at 600^○C using Mössbauer spectrometry, X‐ray diffraction and scanning electron microscopy are reported. At the received state, the two steels present a fine bainitic microstructure with equal hardness. From Mössbauer analysis, two iron sites are identified as substitutional by Cr, Mo, Ni atoms and as insertional by carbon in bainitic ferrite. Both sites are locally deformed by residual stresses. The presence of small quantities of retained austenite and ε carbide has been observed. Annealing for one hour at 600^○C causes a decrease in hardness for both steels with a decrease of retained austenite. After longer time of annealing, precipitation of (Fe,Ni)₂₃C₆ occurs in the Fe-Cr-Ni steel and increases hardness.     

Effect of alloying on the stabilities and catalytic properties of Pt–Au bimetallic subnanoclusters: a theoretical investigation

Density functional theory (DFT) has been applied to study the geometrical and electronic structures and the catalytic properties for NO oxidation of pure Pt and PtAu clusters. The calculated results suggest that Pt₁₀ clusters shows the most stable structure among the pure Pt _n (n = 2–13) clusters with the local maximum Δ₂ E value. The doping of Au atoms reduces the stability of the clusters, and Pt₆Au₄ cluster has the most stable structure among Pt_10?n Au _n (n = 1–7) clusters, due to the closest band centers between Pt and Au atoms (0.83 eV) and the obvious s–p resonance peaks near the Fermi level. Pt₆Au₄ cluster displays the strongest activation of O₂ molecules among Pt_10?n Au _n (n = 0–7) clusters, owing to the clear overlap between O 2p and Pt 6 s and Au 6 s near the Fermi level, and the more positive d band center than the others. The interaction between NO and metals changes slightly in NO/Pt_10-nAu_n (n = 2–7) systems, which is weaker than that in NO/Pt₉Au system, as a result of the decreasing resonance peaks of sp hybridization near the Fermi level. Compared to pure Pt₁₀ cluster, the lower energy barriers and larger reaction energies on Pt₆Au₄ cluster suggest a higher catalytic activity of PtAu cluster for the O₂ dissociation and NO oxidation reactions. Our study provides atomic-scale insights into the nature of the interfacial effect that determines NO oxidation on PtAu cluster catalysts.     

Effect of lead on microstructure and some physical properties of Sn–Zn–Cd alloy

The effect of lead on the structure, electrical resistivity, internal friction, elastic modulus and thermal properties of Sn₈₁Zn₉Cd₁₀ ternary alloys have been investigated using different experimental techniques with their analysis. In addition, properties of this alloy were compared with other Sn–Zn or Sn–Zn–Cd alloys and commercial solder alloys. It has a higher electrical resistivity, internal friction and lower elastic modulus when compared with Sn–Zn or Sn–Zn alloys with other additions such as Cd, Bi or In. The Sn₆₁Zn₉Cd₁₀Pb₂₀ alloy has a lower melting point, electrical resistivity and internal friction when compared with the commercial Pb–Sn solder alloy, but it has a similar elastic modulus.     

Influence of temperature and alloying elements on the threshold displacement energies in concentrated Ni–Fe–Cr alloys

Concentrated solid-solution alloys(CSAs) have demonstrated promising irradiation resistance depending on their compositions. Under irradiation, various defects can be produced. One of the most important parameters characterizing the defect production and the resulting defect number is the threshold displacement energies(E_d). In this work, we report the results of E_dvalues in a series of Ni–Fe–Cr concentrated solid solution alloys through molecular dynamics(MD)simulations. Based on several different empirical potentials, we show that the differences in the E_dvalues and its angular dependence are mainly due to the stiffness of the potential in the intermediate regime. The influences of different alloying elements and temperatures on E_dvalues in different CSAs are further evaluated by calculating the defect production probabilities. Our results suggest a limited influence of alloying elements and temperature on E_dvalues in concentrated alloys. Finally, we discuss the relationship between the primary damage and E_dvalues in different alloys. Overall, this work presents a thorough study on the E_dvalues in concentrated alloys, including the influence of empirical potentials,their angular dependence, temperature dependence, and effects on primary defect production.     

ICEMS study of isothermal oxidation of Fe–Mn–Al–C–Cr–Si–Mo, Fe–Mn–Al–C–Cr–Si and Fe–9Cr–1Mo alloys

The purpose of this paper is to investigate the isothermal behavior of Fe–27.3Mn–7.6Al–C–6.5Cr–0.25Si–0.88Mo (Mo(0)) and Fe–27.3Mn–7.6Al–1.0C–6.5Cr–0.25Si (Mo(1)) alloys and compare it against Fe–9Cr–1Mo (FCR) commercial alloy. The experiments were carried out at 600°C, 700°C, 750°C and 850°C, each one during 72 h in static air. The oxidation kinetics was measured as a function of time using a Thermogravimetry analyzer (TGA). The structure and composition of the oxide scale were characterized by X-ray diffraction (XRD) and Integral Conversion Electron Mössbauer Spectroscopy (CEMS). The TGA results show that at all oxidation temperatures the sample FCR exhibit the lowest kinetic corrosion and the lowest weight gain, whereas Mo(0) the highest. By CEMS technique it were found a broad magnetic sextet, which has been fit by one hyperfine field distribution with mean hyperfine field characteristic to ferritic/martensite phase, one Fe^3?+? doublet and one singlet for the Mo(0) and Mo(1) alloys. Samples oxidized at highest temperatures exhibit a strong paramagnetic line, probably due that the Cr or Mn oxides may be enriched on the surface. Then, the magnetic phase can be converted partially into austenite phase at highest temperatures.     

Influence of Cr on microstructure and elastocaloric effect in Ni–Mn–In–Co–Cr polycrystalline alloys

Ni–Mn-based metamagnetic shape memory alloys have been proposed as potential elastocaloric refrigerants. The intrinsic brittleness of the alloys has limited their cooling application. Introducing a soft second phase is an effective way to reduce the brittleness. From the viewpoint of application, the effect of second phase on elastocaloric effect should be illustrated. In this paper, we have investigated the microstructure, martensitic transformation and elastocaloric effect of Ni₄₅Mn_37-xIn₁₃Co₅Cr_x ($x=0,1\text{ and }2$) polycrystalline alloys. Single-phase and precipitates-containing microstructures are obtained for the undoped and doped alloys, respectively. The precipitates in Cr-doped alloys enhances the fracture strength but significantly hinders the martensitic transformation. Balancing the fracture strength and martensitic transformation, the Ni₄₅Mn₃₆In₁₃Co₅Cr alloy with small amount of precipitates along grain boundaries exhibits large cooling effects of 4–6 K in the temperature range of 317–353 K.     

Effect of alloying on the self-diffusion activation energy in γ-iron

The experimental data on the self-diffusion coefficient of austenite with different chemical compositions obtained by the radioactive isotope method have been analyzed quantitatively. The self-diffusion activation energy in pure γ-iron is shown to be ∼312 kJ/mol. Alloying of austenite with such elements as Mn, Mo, Nb, Ti, and Si (to a lower degree) increases the self-diffusion activation energy, and alloying with C, V, or Cr (for the element content ≥3 at %) decreases it. The empirical formula is derived for calculation of the self-diffusion activation energy in austenite solid solutions with complex composition.     

Effect of helium ion irradiation on the structure and electrical resistivity of nanocrystalline Cr–N and V–N coatings

The structural stability and electrical resistivity of nanocrystalline Cr–N and V–N coatings prepared by ion beam-assisted deposition were studied. The results showed that under helium ion irradiation up to doses of 1.0^.10¹⁷ ion/cm² the fine-crystalline objects successively increase their resistance without apparent structural changes. The subsequent dose increase leads to gas-vacancy void formation and chromium nitride structure destruction. The presence of the initial closed porosity in vanadium nitride favors its structural stability at investigated maximum damage doses.     

Evolution of phase,texture, microstructure and magnetic properties of Fe–Cr–Co–Mo–Ti permanent magnets

Magnetic phase evolution, crystallographic texture, microstructure and magnetic properties of Fe–28Cr–15Co–3.5Mo–1.8Ti alloy have been investigated by X-ray diffractometry, scanning transmission electron microscopy and magnetometry techniques as a function of processing conditions. Heat treatment conditions for obtaining optimum textural, microstructural and magnetic properties have been established by the experimentations. The Goss {110}〈001〉 and cube type {001}〈010〉 textures have been developed in an optimal treated Fe–28Cr–15Co–3.5Mo–1.8Ti magnets. The coercive force in Fe–28Cr–15Co–3.5Mo–1.8Ti magnets depends critically on the shape anisotropy of rod-like Fe Co Ti-rich α₁ particles and remanence on the alignment and elongation of α₁ particles parallel to applied magnetic field 〈100〉 directions. The optimum magnetic properties obtained in Fe–28Cr–15Co–3.5Mo–1.8Ti alloy are intrinsic coercive force, _iH_c, of 78.8 kA/m (990 Oe), remanence, B_r of 1.12 T (11.2 kG) and energy product, (BH)_max of 52.5 kJ/m³ (6.5 MGOe). The development of Fe–28Cr–15Co–3.5Mo–1.8Ti magnets as well as characterization of texture, microstructural and magnetic properties in the current study would be helpful in designing the new Fe–Cr–Co–Mo based magnets suitable for scientific and technological applications.