Effect of Fe doping on the structural and gas sensing properties of ZnO porous microspheres

Fe-doped ZnO porous microspheres composed of nanosheets were prepared by a simple hydrothermal method combined with post-annealing, and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), Brunauer–Emmett–Teller N₂ adsorption–desorption measurements and photoluminescence (PL) spectra. In this paper we report Fe doping induced modifications in the structural, photoluminescence and gas sensing behavior of ZnO porous microspheres. Our results show that the crystallite size decreases and specific surface area increases with the increase of Fe doping concentration. The PL spectra indicate that the 4 mol% Fe-doped ZnO has higher ratio of donor (V_O and Zn_i) to acceptor (V_Zn) than undoped ZnO. The 4 mol% Fe-doped ZnO sample shows the highest response value to ppb-level n-butanol at 300 °C, and the detected limit of n-butanol is below 10 ppb. In addition, the 4 mol% Fe -doped ZnO sample exhibits good selectivity to n-butanol. The superior sensing properties of the Fe-doped porous ZnO microspheres are contributed to higher donor defects contents combined with larger specific surface area.     

Preparation,characterization and electrical property of Mn-doped ceria-based oxides

Manganese-doped ceria-based oxides, Ce_1−xMn_xO_2−δ (0.05 ≤ x ≤ 0.3) and Ce_1−x−yGd_xMn_yO_2−δ˙ (0.05 ≤ x≤ 0.2, 0.05 ≤ y ≤ 0.25) were synthesized, and crystal phase analysis by XRD and measurements of electrical properties were performed. Solubility limit of Mn in Ce_1−xMn_xO_2−δ˙ seemed to be between 5 mol% and 10 mol% and Mn₃O₄ was the main by-product above the solubility limit in the case of heat treatment at 1300 °C. Judging from the oxygen partial pressure dependence of total conductivity and emf measurements, Ce_1−xMn_xO_2−δ˙ is a single-phase mixed conductor within the composition below the solubility limit, and when the composition of Mn exceeds the solubility limit, it becomes the dual-phase mixed conductor of Ce_1−xMn_xO_2−δ˙ and Mn₃O₄. The doing of Mn in gadlia-doped ceria, Ce_1−x−yGd_xMn_yO_2−δ˙ (0.05 ≤ x ≤ 0.2, 0.05 ≤ y ≤ 0.25), was more difficult than that in CeO₂ presumably due to the preferential reaction between Gd and Mn to give GdMnO₃ to the GDC solid solution formation, and the Mn doping seems not to be so effective in preparing the mixed ionic–electronic conductor based on GDC.     

The growth of ZnO:Ga:Cu as new TCO film of advanced electrical,optical and structural quality

Because of having similarities in many physical as well as chemical properties to those of Zn, Cu has been strategically used as an effective dopant e.g., Al, Ga, F, etc., to change the optical, electrical and the micro-structural properties of ZnO thin films for obtaining its favorable opto-electronic performance as a transparent conducting oxide suitable for devices. Present study demonstrates the growth of transparent conducting ZnO:Ga:Cu thin films, by low power RF magnetron sputtering at a low substrate temperature (100 °C). Highly crystalline ZnO:Ga:Cu film with preferred c-axis orientation has been obtained demonstrating a high magnitude of transmission ~85% in the visible range and a high electrical conductivity ~40 S cm^–1, facilitated by large crystallite size (~29 nm), introducing reduced grain boundary scattering. XPS O 1S spectrum reveals the presence of a significant fraction of oxygen atoms effectively increasing the optical transparency. Incorporation of Ga and Cu ions into the ZnO matrix promotes violation of the local translational symmetry as suggested by the relaxation of Raman selection rules for the network, evident by the presence of strong (B₁^high–B₁^low) modes which are typically Raman inactive. The consequences of Cu doping has been compared with identically prepared ZnO and ZnO:Ga films.     

Effects of Cd concentration on structure and optical properties of the ternary Zn1−xCdxO nanopowder prepared by sol–gel method

Zn_1−xCd_xO nanocrystalline powder with different Cd contents (0≤x≤1) has been prepared by new facile sol–gel route. The crystal structure and optical properties were investigated by X-ray diffraction patterns, Transmission electron microscope, X-ray photoelectron spectroscopy, Photoluminescence. As x varied from x=0 to 0.25, the Zn_1−xCd_xO nanopowder exhibits a hexagonal wurtzite structure of pure ZnO without any significant formation of a separated CdO phase. For the samples with 0.5≤x≤0.85, the Zn_1−xCd_xO nanopowder exhibits the coexistence of hexagonal ZnO and cubic CdO phase, meanwhile, the content of ZnO phase decreases while that of CdO increases with increasing the Cd content x. The ultra-violet near-band-edge emission of the Zn_1−xCd_xO nanopowder was monotonously red-shifted from 389 nm (x=0) to 406 nm (x=0.25) due to the direct modulation of band gap caused by Cd substitution.     

Investigation of Li-induced structural disorder and phase transition in ZnO by Raman spectroscopy

Zn_0.8Li_0.2O ceramics with wurtzite structure have been fabricated by a solid reaction of ZnO and Li₂CO₃. The effects of substitutional Li atoms on the crystal structure and structural phase transition of ZnO are studied by Raman spectroscopy. The enhancement of E₁(LO) mode in Zn_0.8Li_0.2O ceramics reveals the occurrence of Li-induced structural disorder. Temperature dependent Raman spectra strongly indicate that a structural phase transition occurs at about 448 K in Zn_0.8Li_0.2O ceramics.     

Synthesis and characterization of layered Li1−x(Ni0.5Co0.5)1−yFeyO2(0 ≤ (1 − x) ≤ 1 and 0 ≤ y ≤ 0.2) cathodes

Layered Li(Ni_0.5Co_0.5)_1−yFe_yO₂ cathodes with 0 ≤ y ≤ 0.2 have been synthesized by firing the coprecipitated hydroxides of the transition metals and lithium hydroxide at 700 °C and characterized as cathode materials for lithium ion batteries to various cutoff charge voltages (up to 4.5 V). While the y = 0.05 sample shows an improvement in capacity, cyclability, and rate capability, those with y = 0.1 and 0.2 exhibit a decline in electrochemical performance compared to the y = 0 sample. Structural characterization of the chemically delithiated Li_1−x(Ni_0.5Co_0.5)_1−yFe_yO₂ samples indicates that the initial O3 structure is maintained down to a lithium content (1 − x) ≈ 0.3. For (1 − x) < 0.3, while a P3 type phase is formed for the y = 0 sample, an O1 type phase is formed for the y = 0.05, 0.1 and 0.2 samples. Monitoring the average oxidation state of the transition metal ions with lithium contents (1 − x) reveals that the system is chemically more stable down to a lower lithium content (1 − x) ≈ 0.3 compared to the Li_1−xCoO₂ system. The improved structural and chemical stabilities appear to lead to better cyclability to higher cutoff charge voltages compared to that found before with the LiCoO₂ system.     

Dielectric and piezoelectric properties of (Bi1−x−yNdxNa1−y)0.5BayTiO3 lead-free ceramics

New lead-free (Bi_1−x−yNd_xNa_1−y)_0.5Ba_yTiO₃ ceramics were prepared by a conventional ceramic technique and their dielectric and piezoelectric properties were studied. X-ray diffraction studies reveal that Nd³⁺ and Ba²⁺ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a new solid solution with a pure perovskite structure, and a morphotropic phase boundary (MPB) of rhombohedral and tetragonal phases is formed at 0.04 < y < 0.10. The partial substitutions of Nd³⁺ and Ba²⁺ decrease effectively the coercive field E_c and increase significantly the remanent polarization P_r. Because of lower E_c, larger P_r and the formation of the MPB, the piezoelectric properties of the ceramics are significantly enhanced at x/y = 0.02/0.06: d₃₃ = 150 pC/N and k_p = 30.5%. The ceramics exhibit relaxor characteristic, which is probably resulted from the cation disordering in the 12-fold coordination sites. The depolarization temperature T_d shows a strong compositional dependence and reaches a minimum value at the MPB. The temperature dependences of the ferroelectric and dielectric properties suggest that the ceramics may contain both the polar and non-polar regions near the depolarization temperature T_d, which cause the polarization hysteresis loop become deformed near/above T_d.     

Effect of fluorine doping on phase formation and properties of Bi(Pb)-2223 ceramics

Superconducting ceramics of Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_yF_x (x = 0–0.6) are prepared in air by conventional solid state reaction and characterized. The study shows that the melting point of the samples decreases as fluorine content increases. As a consequence, the grain size increases with the doping level and for x = 0.6, the sample is completely deformed and presents a concave shape making impossible the measurements on it. The Vickers microhardness reaches its maximum for x = 0.2. The analysis of the X-ray diffraction results reveals that all the samples are composed of only Bi(Pb)-2212 and Bi(Pb)-2223 phases. The highest proportion of the high T_c phase (Bi(Pb)-2223) is also observed for x = 0.2 and is about 67.32%. The refinement of cell parameters is done by considering the structural modulation. The results show that the doping leads to a reduction of cell volume as well as the a axis component of modulation. From resistivity versus temperature measurements, it is shown that the doped phases exhibit higher onset critical transition temperatures than the undoped one. The residual resistivity increases with fluorine content suggesting that the doping introduces structural defects and disorder into the samples. The obtained critical current density at 77 K under zero magnetic field also increases with fluorine doping.     

Synthesis and electrical transport properties of Lu2+xTi2−xO7−x/2 oxide-ion conductors

The Lu_2+xTi_2−xO_7−x/2 (x = 0; 0.052; 0.096; 0.286; 0.44; 0.63; 33.3–49 mol% Lu₂O₃) nanoceramics with partly disordered pyrochlore-type structure are prepared by sintering freeze-dried powders obtained by a co-precipitation technique with 1600 °C annealing. Similar to pyrochlore-like compositions in the zirconate system, some of the new titanates are good oxide-ion conductors in air. The new solid-state electrolytes have oxide-ion conductivity in the interval of 1.0 × 10^− 3 – 2.5 × 10^− 3 S/cm at 740 °C in air. This value of conductivity is comparable with that of ZrO₂/Y₂O₃ ceramics. The conductivity of Lu_2+xTi_2−xO_7−x/2 depends on the chemical composition. The highest ionic conductivity is exhibited by nearly stoichiometric Lu_2+xTi_2−xO_7−x/2 (x = 0.096; 35.5 mol% Lu₂O₃) material containing ∼ 4.8 at.% Lu_Ti anti-site defects.     

Microstructure and varistor properties of ZnO–V2O5–MnO2 ceramics with Ta2O5 addition

The effect of Ta₂O₅ addition on microstructure, electrical properties, and dielectric characteristics of the quaternary ZnO–V₂O₅–MnO₂ vaistor ceramics was investigated. Analysis of the microstructure indicated that the quaternary ZnO–V₂O₅–MnO₂–Ta₂O₅ ceramics consisted of mainly ZnO grain and minor secondary phases such as Zn₃(VO₄)₂, ZnV₂O₄, TaVO₅, and Ta₂O₅. As the amount of Ta₂O₅ increased, the sintered density increased from 94.8 to 97.2% of the theoretical density (5.78 g/cm³ for ZnO), whereas the average grain size decreased from 7.7 to 6.0 μm. The ceramics added with 0.05 mol% Ta₂O₅ exhibited the highest breakdown field (2715 V/cm) and the highest nonlinear coefficient (20). However, further increase caused α to abruptly decrease. The Ta₂O₅ acted as a donor due to the increase of electron concentration in accordance with the amount of Ta₂O₅. The donor concentration increased from 1.97×10¹⁸ to 3.04×10¹⁸cm^?3 with increasing the amount of Ta₂O₅ and the barrier height exhibited the maximum value (0.95 eV) at 0.05 mol% Ta₂O₅.     

A co-doping approach towards enhanced ionic conductivity in fluorite-based electrolytes

A co-dopant strategy is used to investigate the effect that the elastic strain in the lattice has on the grain ionic conductivity of doped ceria electrolytes. Based on critical dopant ionic radius (r_c), different compositions in the Lu_xNd_yCe_1−x−yO_2−δ (x + y = 0.05, 0.10, 0.15, and 0.20) system are studied. Dopants are added such that the weighted average dopant ionic radius matches r_c for all the compositions. Dense ceramic discs are prepared using conventional solid oxide route and sintering methods. Precise lattice parameter measurements are used to calculate the lattice strain. The ionic conductivity of the samples is measured in the temperature range of 250 °C to 700 °C using two-probe electrochemical impedance spectroscopy technique. The elastic strain present in Lu_xNd_yCe_1−x−yO_2−δ system is found to be negligible when compared to Lu_xCe_1−xO_2−δ (negative) and Nd_xCe_1−xO_2−δ (positive) systems. Grain ionic conductivity of Lu_xNd_yCe_1−x−yO_2−δ (where x + y = 0.05) at 500 °C is observed to be 1.9 × 10^− 3 S/cm which is twice as high as that of Lu_0.05Ce_0.95O_2−δ. These results extend the validity of the r_c concept as a strategy for co-doping ceria electrolytes and open new designing avenues for solid oxide electrolytes with enhanced ionic conductivity.     

Mixed conducting perovskite-like ceramics on the base of lanthanum gallate

Ceramic perovskite solid solutions (La_0.9Sr_0.1)[(Ga_1−xM_x)_0.8Mg_0.2]O_3−y, 0 ≤ x ≤ 0.5, M = Fe, Ni, Cr (systems I–III) and brownmillerite solid solutions (La_0.2Sr_1.8)[Ga(Fe_1−xMg_x)]O_5−z, 0 ≤ x ≤ 0.5, (system IV) have been prepared. The samples have been studied by X-ray diffraction and electron microscopy methods, dielectric spectroscopy and permeability measurements. The correlation between the composition, unit cell parameter changes, electrical transport and oxygen permeation properties has been revealed. Introduction of transition metals (Fe, Ni, or Cr), substituting for gallium, ensures the enhancement of the electronic constituent of the conductivity in the perovskite systems I–III. Stabilization of the transition metal high valence states 4+ or 5+ has been suggested for compositions I and III. This leads to a unit cell volume contraction and provides a decrease in the concentration of oxygen vacancies. The oxygen permeability reaches its maximum values in compositions I–III with x ∼ 0.3. On the contrary, increasing concentration of the doping element with lower valence state (magnesium), substituting for iron, determines the expansion of the brownmillerite unit cell volume and provides an increase of the oxygen vacancy concentration, which in turn, favors the enhancement of oxygen permeability of composition IV.     

Structural and optical properties of Mn-doped ZnO nanocrystalline thin films with the different dopant concentrations

The transparent nanocrystalline thin films of undoped zinc oxide and Mn-doped (Zn_1−xMn_xO) have been deposited on glass substrates via the sol–gel technique using zinc acetate dehydrate and manganese chloride as precursor. The as-deposited films with the different manganese compositions in the range of 2.5–20 at% were pre-heated at 100 °C for 1 h and 200 °C for 2 h, respectively, and then crystallized in air at 560 °C for 2 h. The structural properties and morphologies of the undoped and doped ZnO thin films have been investigated. X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to examine the morphology and microstructure of the thin films. Optical properties of the thin films were determined by photoluminescence (PL) and UV/Vis spectroscopy. The analyzed results indicates that the obtained films are of good crystal quality and have smooth surfaces, which have a pure hexagonal wurtzite ZnO structure without any Mn related phases. Room temperature photoluminescence is observed for the ZnO and Mn-doped ZnO thin films.     

Ferroelectric properties of Pb(Zr1/2Ti1/2)O3–Pb(Zn1/3Nb2/3)O3 ceramics under compressive stress

Effects of compressive stress on the ferroelectric properties of ceramics in PZT–PZN system were investigated. The ceramics with a formula (1−x)Pb(Zr_1/2Ti_1/2)O₃–xPb(Zn_1/3Nb_2/3)O₃ or (1−x)PZT–(x)PZN (x = 0.1–0.5) were prepared by a conventional mixed-oxide method. The ferroelectric properties under the compressive stress of the PZT–PZN ceramics were observed at the stress levels up to 170 MPa using a compressometer in conjunction with a modified Sawyer–Tower circuit. It was found that with increasing compressive stress the area of the ferroelectric hysteresis (P–E) loops, the saturation polarization (P_sat), the remnant polarization (P_r), and the coercive field (E_c) decreased. These results were interpreted through the non-180° ferroelastic domain switching processes.     

Noise behavior of amorphous GexSi1−xOy for microbolometer applications

High resistivity sputtered a-Ge_xSi_1−xO_y compound was investigated for application to microbolometer fabrication for thermal imaging. Noise behavior of the fabricated bolometers was measured, showing no evidence of random telegraph switching (RTS) noise. 1/f noise was measured at several measuring currents, resulting in a 1/f noise factor of 2.9 × 10⁻¹¹ that can be used for further design and modeling.     

Electrical and mechanical properties of diluted magnetic semiconductor Zn1−xMnxS nanocrystalline films

Nanostructured Zn_1−xMn_xS films (0 ⩽ x ⩽ 0.25) were deposited on glass substrates by simple resistive thermal evaporation technique. All the films were deposited at 300 K in a vacuum of 2 × 10⁻⁶ m bar. All the films temperature dependence of resistivity revealed semiconducting behaviour of the samples. Hot probe test revealed that all the samples exhibited n-type conductivity. The nanohardness of the films ranges from 4.7 to 9.9 GPa, Young’s modulus value ranging 69.7–94.2 GPa.     

Nb doping effect on TiO2−x films for bolometer applications

Nb-doped TiO_2−x thin films were deposited using a 1 at% niobium doped titanium target by RF reactive magnetron sputtering at various oxygen partial pressures (pO₂). The films appeared amorphous in the pO₂ range of 4.4–4.7% with resistivity ranging from 0.39 Ω cm to 2.48 Ω cm. Compared to pure TiO_2−x films, the resistivity of the Nb-doped TiO_2−x films did not change sensitively with the oxygen partial pressure, indicating that the resistivity of the films can be accurately controlled. 1/f noise parameter of Nb-doped TiO_2−x films were found to decrease largely while the measured temperature coefficient of resistance (TCR) of the films was still high. The obtained results indicate that Nb-doped TiO_2−x films have great potential as an alternative bolometric material.     

Ferroelectric phase transition and optical performance of PLZnNZT transparent ceramics

Lead-based Pb_0.97La_0.02(Zn_1/3Nb_2/3)_0.3(Zr_0.53Ti_0.47)_0.7O₃ (PLZnNZT) transparent ceramics with the addition of 2 wt% excess PbO were prepared by hot-pressing sintering method. The hot-pressing sintered PLZnNZT ceramics exhibit dense and large-grained microstructure, and perovskite structure with distorted cubic-like symmetry. The ceramics exhibit normal ferroelectric-like dielectric behavior with slightly diffused ferroelectric phase transition characteristic. The PLZnNZT ceramics exhibit fully developed, symmetric and saturated P–E hysteresis loop and large piezoelectric constant d₃₃, being 468 pC/N. The ceramics with 120 μm thickness exhibit maximum transmittance of 53% at 850 nm when Fresnel losses was not included, almost totally transparent in the mid IR region (2500–5600 nm), and low-lying optical band gap energy E_g of 3.23 eV. Three diffused Raman bands centering around 240 cm⁻¹, 560 cm⁻¹ and 750 cm⁻¹ are observed by micro-Raman spectroscopy, which can be attributed to F2g [BO₆] bending vibration, A1g [BO₆] stretching vibration and “soft mode” mixed by the bending and stretching vibrations, respectively, confirming the normal ferroelectric-like characteristic.     

A comparative study of different concentrations of pure Zn powder effects on synthesis,structure, magnetic and microwave-absorbing properties in mechanically-alloyed Ni–Zn ferrite

In this study, a powder mixture of Zn, Fe₂O₃ and NiO was used to produce different compositions of Ni_1−xZn_xFe₂O₄ (x=0.36, 0.5 and 0.64) nanopowders. High-energy ball milling with a subsequent heat treatment method was carried out. The XRD results indicated that for the content of Zn, x=0.64 a single phase of Ni–Zn ferrite was produced after 30 h milling while for the contents of Zn, x=0.36 and 0.5, the desired ferrite was formed after sintering the 30 h-milled powders at 500 °C. The average crystallite size decreased with increase in the Zn content. A DC electrical resistivity of the Ni–Zn ferrite, however, decreased with increase in the Zn content, its value was much higher than those samples prepared by the conventional ceramic route by using ZnO instead of Zn. This is attributed to smaller grains size which were obtained by using Zn. The FT-IR results suggested two absorption bands for octahedral and tetrahedral sites in the range of 350–700 cm⁻¹. The VSM results revealed that by increasing the Zn content from 0.36 to 0.5, a saturation magnetization reached its maximum value; afterwards, a decrease was observed for Zn with x=0.64. Finally, magnetic permeability and dielectric permittivity were studied by using vector network analyzer to explore microwave-absorbing properties in X-band frequency. The minimum reflection loss value obtained for Ni_0.5Zn_0.5Fe₂O₄ samples, about −34 dB at 9.7 GHz, making them the best candidates for high frequency applications.