Novel comb-type hydrogels of net-[PP-g-AAc]-g-4VP synthesized by gamma radiation,with possible application on Cu2+ immobilization

A novel comb-type grafted hydrogel system of net-[PP-g-AAc]-g-4VP was synthesized by gamma radiation in three steps. In the first step a pH sensitive graft copolymer of AAc onto PP film was obtained by radiation grafting of acrylic acid (AAc) onto polypropylene (PP) films in aqueous solution at radiation doses of 10 kGy with a ⁶⁰Co source. The grafted side chains of poly (acrylic acid) (PAAc) were then cross-linked with gamma radiation at different radiation doses to give net-[PP-g-AAc]. Finally, 4-vinylpyridine (4VP) was grafted into the net-[PP-g-AAc]. The comb-type grafted hydrogel obtained, net-[PP-g-AAc]-g-4VP, has been studied through determination of graft yield and swelling behavior at room temperature. Two critical pH values were found for net-[PP-g-AAc]-g-4VP at 4.5 and 7.2. Initial studies on the immobilization of Cu²⁺ ions from solution into net-[PP-g-AAc]-g-4VP films were performed.The comb-type grafted hydrogel, grafted onto PP was also characterized by differential scanning calorimetry (DSC), scanning electronic microscopy (SEM) and FTIR-ATR.     

Synthesis and characterization of thermosensitive interpenetrating polymer networks based on N-isopropylacrylamide/N-acryloxysuccinimide, crosslinked with polylysine, grafted onto polypropylene

Interpenetrating polymer networks (IPNs) based on poly (N-isopropylacrylamide), (PNIPAAm) and poly (N-acryloxysuccinimide) (PNAS), grafted onto polypropylene (PP), were synthesized in three consecutive steps using ionizing radiation in the first and second steps and chemical reaction in third one. In the first step a thermosensitive graft copolymer of NIPAAm onto PP film was obtained by gamma radiation with a ⁶⁰Co source. The grafted side chains of PNIPAAm were then crosslinked with gamma radiation to give net-[PP-g-NIPAAm]. The secondary network was obtained in situ by chemical crosslinking between PNAS and polylysine (pLys). The PP-g-IPNs exhibited the lower critical solution temperature (LCST) at around 32 °C. Based on its thermoreversible behavior, this system could be used for immobilization of biomolecules. The phase transition temperature (LCST) and network properties of the IPNs were measured by swelling behavior. Additional characterization by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and infrared (FTIR-ATR) determinations are reported.     

Radiation grafting of N,N′-dimethylacrylamide and N-isopropylacrylamide onto polypropylene films by two-step method

Polypropylene (PP) films were modified by the consecutive grafting of N,N′-dimethylacrylamide (DMAAm) and N-isopropylacrylamide (NIPAAm) (two-step method) using preirradiation method with gamma-rays. The effect of absorbed dose, monomer concentration and reaction time on the degree of grafting was determined. The grafted samples were verified by the FTIR-ATR spectroscopy; thermal properties were analyzed by differential scanning calorimetry (DSC) and the stimuli-responsive behavior was studied by swelling and contact angle in water as well as DSC. Thermoresponsive films of (PP-g-DMAAm)-g-NIPAAm presented a lower critical solution temperature (LCST) at 36.5 °C.     

PP films grafted with N-isopropylacrylamide and N-(3-aminopropyl) methacrylamide by γ radiation: synthesis and characterization

Simultaneous grafting of N-isopropylacrylamide (NIPAAm) and N-(3-aminopropyl) methacrylamide hydrochloride (APMA) on polypropylene (PP) was investigated for obtaining interfaces that are stimuli-responsive under physiological conditions. A pre-irradiation method was optimized tuning the γ-irradiation dose, reaction time, temperature, and monomers concentrations. FT-IR ATR and XPS analysis of the grafted copolymers evidenced a greater content in NIPAAm than in APMA; the APMA/NIPAAm ratio increasing with the concentration of APMA in the reaction medium and when the grafting was carried out in 1 M NaNO₃. The grafted films were characterized regarding their thermal properties (DSC and TGA) swelling behavior and contact angle. Immersion of the pre-irradiated films in 1 M NIPAAm/0.5 M APMA aqueous solution rendered PP-g-(1NIPAAm-r-0.5APMA) which exhibited rapid and reversible transitions showing a LCST around the physiological temperature. By contrast, a greater content in APMA enhanced the hydrophilicity and prevented the shrinking of PP-g-(1NIPAAm-r-1APMA).     

Radiation-induced grafting of stimuli-responsive binary monomers: PDMAEMA/PEGMEMA onto PP films

Both poly[2-(dimethylamino) ethyl methacrylate] (PDMAEMA) and poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) were radiation grafted onto polypropylene films (PP) using gamma radiation from a ⁶⁰Co source. PP was pre-irradiated by gamma ray for modification following by grafted PDMAEMA and PEGMEMA by a one step method. Grafting was studied as a function of the pre-irradiation dose between 20 and 180 kGy, dose rate of 10.4 kGy/h, and monomer concentration 50% of PDMAEMA/PEGMEMA (1/1) in different solvents (toluene, acetone, and methanol). FTIR-ATR, TGA, and DSC were carried out in the characterization of the graft copolymer obtained. Stimuli-responsive behavior and critical pH point were studied by swelling in water. pH and thermo-responsive films of PE-g-(DMAEMA/PEGMEMA) presented a lower critical solution temperature (LCST) of 50 °C and critical pH point around 8.7.     

Radiation grafting of NIPAAm and acryloxysuccinimide onto PP films and sequent crosslinking with polylysine

N-isopropylacrylamide (NIPAAm) and N-acryloxysuccinimide (NAS) were grafted from their binary mixtures in tetrahydrofurane (THF) and toluene solutions onto polypropylene (PP) films by the pre-irradiation oxidative method in air. Effects of pre-irradiation dose, dose rate, and monomer concentrations (NAS/NIPAAm) were studied. The grafted copolymers exhibited the lower critical solution temperature (LCST) at around 31 °C. Based on its thermo-reversible behavior, this system has been used for immunoassay, drug delivery, separation processes and immobilization of enzymes. N-acryloxysuccinimide (NAS) has been used as an active ester to bind proteins through amide bond formation with lysine, and because of this property, the grafted copolymer has been crosslinked with polylysine. Techniques used to characterize the films included differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), infrared (FTIR-ATR) and elemental analysis. Results on thermo-sensitivity are presented. This new system could find applications in vesicle immobilizations.     

Radiation grafting of pH and thermosensitive N-isopropylacrylamide and acrylic acid onto PTFE films by two-steps process

Polytetrafluoroethylene (PTFE) was grafted (g) with acrylic acid (AAc) by γ-ray pre-irradiation method to get PTFE-g-AAc films, then N-isopropylacrylamide (NIPAAm) was grafted onto PTFE-g-AAc films with γ-ray to get (PTFE-g-AAc)-g-NIPAAm. PTFE films were irradiated in air at a dose rate of 3.0 kGy h^–1 and different radiation dose. The irradiated films were placed in glass ampoules, which contained aqueous solutions with different monomer concentration (AAc), and then they were heated at different temperatures and reaction time. NIPAAm onto PTFE-g-AAc was carried out with the same procedure with monomer concentration of 1 mol L⁻¹. The thermosensitivity of the samples was defined and calculated as the ratio of the grafted samples swelling at 28 and 35 °C, and pH sensitivity defined as the ratio of the grafted samples swelling at pH 2 and 8.     

Trapping and release of cargo molecules from a micro-stamped mesoporous thin film controlled by poly(NIPAAm-co-AAm)

Materials that utilize the micropatterned structure of a mesoporous silica film to successfully load and release cargo using a thermal sensitive polymer are presented in this paper. Films with pore sizes of ~2 and ~5 nm aligned in the pulling direction were synthesized using evaporation induced self-assembly techniques. The pores are exposed using a new method of stamping micropatterns without the use hydrofluoric acid. A well studied temperature dependent polymer [poly(N-isopropylacrylamide-co-acrylamide)] was grafted onto the surface of these films to act as a temperature activated gatekeeper. Below the lower critical solution temperature (LCST) the polymer is erect and can block the pore openings, trapping cargo inside the pores. When the temperature is above the LCST the polymer collapses and unblocks the pores, allowing cargo to escape. The loading capacities as well as the reusability of these films were studied.     

Novel interpenetrating smart polymer networks grafted onto polypropylene by gamma radiation for loading and delivery of vancomycin

Gamma radiation was used in every step of the synthesis of a sequential interpenetrating polymer network made of two “smart” polymers: poly(acrylic acid) (PAAc) and poly (N-isopropylacrylamide) (PNIPAAm), the latter grafted onto polypropylene (PP) films (PP-g-PNIPAAm) with the aim of developing medicated coatings for medical devices. Three steps were followed for obtaining net-PP-g-PNIPAAm-inter-net-PAAc: graft copolymerization of PNIPAAm onto PP films by gamma pre-irradiation oxidative method, cross-linking of PP-g-PNIPAAm by gamma irradiation in water to form the first network, with or without N,N′-methylenebis(acrylamide) (MBAAm), and finally the formation of the second network through the polymerization and cross-linking of AAc inside cross-linked PP-g-PNIPAAm by a low gamma radiation dose of 2.5 kGy. The films were characterized regarding the amount of grafted polymers and their composition (FTIR-ATR), thermal behavior (DSC), temperature- and pH-responsive swelling and contact angle (critical pH 6 and lower critical solution temperature ∼33 °C), and loading and release rate of vancomycin. Drug loading was driven by specific interactions between vancomycin and PAAc. Drug-loaded films sustained the delivery for several hours at pH 7.4 and provided release rate values adequate for killing bacteria attempting to adhere the surface of the films.     

Drug permeation modeling through the thermo-sensitive membranes of poly(N-isopropylacrylamide) brushes grafted onto micro-porous films

Temperature-sensitive N-isopropylacrylamide (NIPAAm) polymer brushes of known molecular weight (20k–25k) were grafted onto micro-porous polycarbonate (PC) films (pore size 0.4 μm) using argon plasma treatment. The resulting composite membranes were tested for controlled drug release at various grafted chain density, which was controlled using 1–3% polymer concentrations. The composites were also characterized in terms of graft yield, membrane thickness, Fourier transform infrared (FTIR) spectra and scanning electron micrography (SEM). The drug permeabilities of 4-acetamidophenol and ranitidine HCl in the resulting membranes were determined at temperatures between 30 and 40 °C. The drug permeability changed remarkably at 34 °C, near the lower critical solution temperature (LCST). The drug passage was regulated by swelling (which occurs at a temperature lower than the LCST) or shrinkage (occurring at an elevated temperature) of the PNIPAAm polymer brushes. These membranes demonstrated on–off ratios of drug permeabilities up to 11 and 14 for the model drugs, respectively. These values are higher than most literature data with similar-size model molecules. The excellent on–off valve mechanism was discussed in terms of the suitable molecular weight and grafted chain density in relation to the pore size and porosity of the PC support. A mathematical model was proposed to predict the drug permeation flux based on the gel conformation data, graft density, characteristics of the micro-porous support, and drug concentrations and diffusivities in water and in the PNIPAAm gel. The model can successfully estimate the drug permeation flux through the composite with higher (0.42 mg cm⁻²) graft density with a coefficient of determination of 0.95. The discrepancy between the predicted and experimental data at the lower graft density (0.12 mg cm⁻²) was ascribed to pore channel narrowing resulting from the uneven polymer chain distribution.     

Thermorheological and glass transition properties of PNIPA/PVP and PNIPA/Carbopol blends

The miscibility of poly(N-isopropylacrylamide) (PNIPA) with poly(vinyl pyrrolidone) (PVP) and a cross-linked poly(acrylic acid) (Carbopol^® 971P) was evaluated from the rheological data of aqueous dispersions and the temperature of glass transitions of films made of binary mixtures. PNIPA has a low critical solubility temperature (LCST) of about 33°C, below which 1% dispersion behaves as a viscous system. At temperatures above LCST, the hydrophobic interactions among the isopropyl groups initially provide transient networks of greater elasticity. The LCST of PNIPA as well as its T _g (144°C, estimated by DSC and MTDSC of films) were not modified by the presence of PVP. The immiscibility of PNIPA and PVP was confirmed by the absence of interaction between both polymers as shown by FTIR analysis of the films. In contrast, PNIPA and carbopol were miscible and the behaviour of their mixtures differed significantly from that of the parent polymers; i.e. a strong synergistic effect on the viscoelasticity of the dispersions was observed below the LCST. As temperature increased, the blends showed a decrease in the loss and storage moduli, especially those with greater PNIPA proportions. The fall was smoother as the PNIPA proportion decreased. This behaviour may be explained as the result of the balance between PNIPA/carbopol hydrogen bonding interactions (as shown in the shift of C=O stretch in FTIR spectra) and PNIPA/PNIPA hydrophobic interactions. The T _g values of the films of the blends showed a positive deviation from the additivity rule; the mixtures containing more than 1:1 amide:carboxylic acid groups have a notably high Tg (up to 181°C). This increase is related to the stiffness induced in the films by the PNIPA/carbopol interactions.     

γ-Ray-induced grafting of DMAEMA and AAc onto PP by two step method

Binary graft copolymerization of thermosensitive 2-(dimethylamino) ethyl methacrylate (DMAEMA) and pH sensitive acrylic acid (AAc) monomers onto polypropylene (PP) films was carried out by a two step method using a ⁶⁰Co gamma radiation source. The PP film was initially modified by grafting of DMAEMA through a direct method. The DMAEMA-g-PP film obtained was then subjected to radiation grafting of AAc by the pre-irradiation method to give (DMAEMA-g-PP)-g-AAc. The optimal conditions, such as reaction time, reaction temperature, monomer concentration, and dose were studied. The grafted samples were verified by the FTIR-ATR spectroscopy and swelling; thermal properties were analyzed by DSC and TGA.     

Alpha,omega-functionalized poly-N-isopropylacrylamides: controlling the surface activity for vesicle adsorption by temperature

The synthesis of alpha,omega-end-functionalized copolymers of N-isopropylacrylamide and N-(3-dimethylaminopropyl)acrylamide was performed. Monomer ratios of 100:0, 96:4, and 81:19 were investigated. The lower critical solution temperature (LCST) of these polymers was determined by cloud-point measurements and by microcalorimetric measurements. The LCST increased from 32 over 37 to 47 degrees C as the hydrophobicity increased with increasing amount of comonomer N-(3-dimethylaminopropyl)acrylamide. The polymers could successfully be adsorbed onto gold surfaces. Finally, vesicle adsorption onto these self-assembled polymer films on flat gold surfaces was investigated as the vesicle solution temperature was varied. It could be observed that vesicle adsorption was hindered as long as the temperature of the vesicle solution was above the LCST of the polymer. As soon as it dropped below the LCST the vesicle adsorption process was initiated.     

Random copolymers of N-isopropylacrylamide and methacrylic acid monomers with hydrophobic spacers: pH-tunable temperature sensitive materials

Two series of random copolymers of N-isopropylacrylamide (NIPAAm) and comonomers derived from methacrylic acid with a different number of methylene units as hydrophobic spacers (n=4, 7 and 10) were synthesized via free radicals. The first series was prepared having the acid groups methoxy-protected while the second series have the acid groups free. The NIPAAm-copolymers of both series were prepared varying the comonomer content from 5 to 20 mol%. All the copolymers were characterized by FTIR, DSC, ¹H NMR and SLS. The aqueous solution behaviour of the copolymers having methoxy-protected acid groups shows that the comonomer increases the hydrophobicity of the copolymer chain and decreases its lower critical solution temperature (LCST). For the copolymers having free acid groups, hydrogen-bonding is responsible for a further decrease in the LCST of these copolymers in pure water. In buffer solutions, every acid comonomer have a critical ionization degree (α_crit) above which the LCST increases with increasing comonomer content while at an ionization degree lower than α_crit the LCST decreases with increasing comonomer content. In dependence of comonomer content, number of methylene units in the spacer and the pH of the buffer solution, the LCST of the copolymers can be varied widely, showing that these random copolymers have pH-tunable temperature sensitivity.     

Thermo‐responsive glycopolymer chains grafted onto honeycomb structured porous films via RAFT polymerization as a thermo‐dependent switcher for lectin Concanavalin a conjugation

Stable and surface‐modified films with regular porous arrays were created by crosslinking honeycomb structured porous films prepared via breath figures from poly(styrene‐co‐maleic anhydride). The formation of open or closed pores of the films was controlled by the addition of a polyion complex. Subsequent crosslinking of the films with 1,8‐diaminooctane led to films, which maintain their structure in solvents. In addition, excess amino functionality after crosslinking allowed the attachment of RAFT agent, 3‐benzylsulfanyl thiocarbonyl sulfanylpropionic acid, for the controlled surface polymerization of N‐isopropyl acrylamide (NIPAAm) and N‐acryloyl glucosamine (AGA). The attachment of thermo‐responsive glycopolymers onto the honeycomb structured porous films was confirmed using contact angle measurements and confocal fluorescence microscopy. Cleavage of surface anchored polymers via aminolysis revealed that the molecular weights of the surface grafted chains are significantly larger than the molecular weight of the chains generated in solution. The honeycomb structured porous films with their grafted PNIPAAm‐ran‐PAGA polymer chains showed selective recognition of Concanavalin A (ConA). Below the lower critical solution temperature (LCST) of the surface, the conjugation is switched off, while above the LCST the surface grafted glucose moieties bind strongly to ConA. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3440–3455, 2010     

Radiation-induced grafting of sensitive polymers

Films of PP and PTFE were modified by gamma-radiation grafting of pH and thermo sensitive monomers (two step method) by using both the preirradiation and the direct methods. The effects of the absorbed dose, monomer concentration and reaction time were investigated. The surface chemistry of grafted samples was analyzed by FTIR-ATR spectroscopy, while their thermal properties were analyzed by TGA and DSC. The stimuli-responsive behavior was studied by swelling and contact angle in water, as well as by DSC. Sensitive films presented a critical pH and LCST.     

Post-irradiation time effects on the graft of poly(ethylene-alt-tetrafluoroethylene) (ETFE) films for ion exchange membrane application

Grafting of styrene followed by sulfonation onto poly(ethylene-alt-tetrafluoroethylene) (ETFE) was studied for synthesis of ion exchange membranes. Radiation-induced grafting of styrene onto ETFE films was investigated after simultaneous irradiation (in post-irradiation condition) using a ⁶⁰Co source. The ETFE films were irradiated at 20 kGy dose at room temperature and chemical changes were monitored after contact with styrene for grafting. The post-irradiation time was established at 14 days when the films were remained in styrene/toluene 1:1 v/v. After this period the grafting degree was evaluated in the samples. The grafted films were sulfonated using chlorosulfonic acid and 1, 2-dichloroethane 20:80 (v/v) at room temperature for 5 h. The membranes were analyzed by infrared spectroscopy (FTIR), differential scanning calorimeter (DSC), thermogravimetric measurements (TG) and degree of grafting (DOG). The ion exchange capacity (IEC) of membranes was determined by acid–base titration and the values for ETFE membranes were achieved higher than Nafion^® films. Preliminary single cell performance was made using pure H₂ and O₂ as reactants at a cell temperature of 80 °C and atmospheric gas pressure. The fuel cell performance of ETFE films was satisfactory when compared to state-of-art Nafion^® membranes.     

Insulin release behavior of poly(N-isopropylacrylamide-co-N-vinyl-2-pyrrolidone) hydrogel based on modified melamine crosslinkers

Novel hydrogels based on poly(N-isopropylacrylamide-co-N-vinyl-2-pyrrolidone) (PNIPAAm/PNVP), were synthesized by solution radical polymerization using water as solvent and different weight percentage of crosslinkers ranging from 0.5 to 4%. The monomer mol ratios of NIPAAm/VP (0.9/0.1, 0.5/0.5, and 0.1/0.9) were used in all cases. N,N′-methylenebisacrylamide (MBA) and the new synthesized N,N,N-triacrylamido melamine (MAAm) were used as crosslinkers. The swelling parameters such as the swelling ratio Q, equilibrium water content (EWC), volume fraction of polymer φ_p and volume fraction at crosslinking φ_r were calculated from swelling measurements at different temperatures. The lower critical solution temperatures (LCST) of the prepared hydrogels were measured using DSC technique. The data of LCST indicated that the NIPAAm/VP crosslinked with MAAm or MBA showed reversible swelling and shrinking with temperature changes. The temperature dependence of swelling ratio and response kinetics upon heating or cooling was also investigated to understand the smart properties, i.e., temperature sensitive properties of these smart hydrogels. The in vitro release experiments were carried out at 22 and 37°C, respectively, to investigate the effect of temperature-sensitive property of these PNIPAAm/PNVP hydrogels crosslinked with MAAm and MBA crosslinkers on insulin release profiles.     

Studies on the copolymerisation of N-isopropyl-acrylamide with glycidyl methacrylate

The paper describes the homopolymerisation and copolymerisation of N-isopropyl acrylamide (NIPAM) with glycidyl methacrylate (GMA) in solution at 60°C using azobisisobutyronitrile (AIBN) as an initiator and dioxan as solvent. Copolymers were synthesized by varying the mol fraction of GMA in the initial feed from 0.025-0.125. All the polymerization reactions were terminated at low % conversion (10-15%) and the copolymer composition was determined by measuring the epoxy content. Percent epoxy content was determined by titration method using pyridine-HCl mixture. The reactivity ratios determined using Fineman-Ross method were found to be 0.94±0.05 (r₁, NIPAM) and 1.05±0.08 (r₂, GMA). All the polymers have high molecular weights with wide molecular weight distribution as determined by gel permeation chromatography (GPC) i.e. M_n in the range of 3.7 x 10⁴ - 7.8 x 10⁴ and M_w in the range of 1.2 x 10⁵ - 4.1 x 10⁵ with a polydispersity index in the range of 2.3-5.3. Lower critical solution temperature (LCST) of NIPAM homopolymer and copolymers was determined by recording DSC scans of polymers in aqueous solution. Incorporation of GMA in the poly(NIPAM) backbone resulted in a decrease in the LCST.     

Radiation grafting of N,N′-dimethylacrylamide and 2-hydroxyethylmethacrylate onto polypropylene films by one step method

The work presented herein reports on polypropylene films grafted with N,N′-dimethylacrylamide and 2-hydroxyethylmethacrylate. The grafted films were obtained by an oxidative pre-irradiation method in one step using a gamma source of ⁶⁰Co. The optimal conditions such as reaction time, monomer concentrations and radiation doses were investigated. Characterization of the grafted polymers was carried out through FTIR-ATR, TGA, DSC, and swelling. Grafts onto polymeric films between 10 and 850% were obtained at doses from 20 to 150 kGy and a dose rate of 8.3 kGy/h.