Speciation of chromium in mineral waters and salinas by solid-phase extraction and graphite furnace atomic absorption spectrometry

A simple GF-AAS method for speciation analysis of chromium in mineral waters and salinas was developed. Cr(VI) species were separated from Cr(III) by solid-phase extraction with APDC (ammonium pyrrolidinedithiocarbamate). The APDC complexes were formed in the sample solution under proper conditions, adsorbed on Diaion HP-2MG resin and the resin was separated from the sample. After elution with concentrated nitric acid Cr(VI) was determined by GF-AAS. Total chromium was determined by GF-AAS directly in the sample and Cr(III) concentration was calculated as the difference between those results.

The detection limit of the method defined as 3 s of background variation was 0.03 μg l⁻¹ for Cr(VI) and 0.3 μg l⁻¹ for total chromium. RSD for Cr(VI) determination at the concentration of 0.14 μg l⁻¹ was 9%, and for total chromium at the concentration of 5.6 μg l⁻¹ was 5%. The recovery of Cr(VI) was in the range of 94–100%, dependently on type of the sample.

The investigation of recovery of the spiked Cr(VI) showed that at concentration levels near 1 μg l⁻¹ and lower recovery may be reduced significantly even by pure reagents that seem to be free from any reductants.     

Determination of diethylhexyl phtalate in water by solid phase microextraction coupled to high performance liquid chromatography

Difficulties detected in the determination of the diethylhexylphthalate (DEHP) at trace levels by gas chromatography–mass spectrometry (GC–MS) using SPME, due to its ubiquitous distribution in the environment has been overcome and a new method for the determination of DEHP in drinking water has been proposed. The method is based on solid phase microextraction (SPME) coupled to high-performance liquid chromatography (HPLC). Detection was carried out spectrophotometrically. Calibration graph was linear in the range 10–110 μg/L with a regression coefficient of r² = 0.998 and a detection limit of 0.6 μg/L. The relative standard deviation was 5 and 2% (n = 4) for chromatographic areas and retention times, respectively. The usefulness of the SPME–HPLC technique was confirmed.     

Simultaneous determination of catecholamines by ion chromatography with direct conductivity detection

A simple method for simultaneous determination of three catecholamines using ion chromatography (IC) with direct conductivity detection (CD) based on the ionization of catecholamines in acidic medium without chemical suppression is developed in the present paper. The method could be used for the determination of these catecholamines in pharmaceutical preparations for the purpose of drug quality control. The recovery of catecholamines was more than 97% (n=3) and the relative standard deviation (R.S.D.) (n=11) was less than 2.1%. In a single chromatographic run, norepinephrine (NE), epinephrine (E) and dopamine (DA) can be determined in less than 10 min. The detection limits were found to be 0.001 μg/ml for NE, 0.01 μg/ml for E and DA respectively. Linear ranges were 0.01–50 μg/ml for NE (r²=0.9998), 0.1–50 μg/ml for E (r²=0.9995) and DA (r²=0.9999), respectively.     

Enantioseparation and quality control of biperiden in pharmaceutical formulations by capillary electrophoresis

An original capillary electrophoretic method has been developed and applied for the enantioselective analysis of the antiparkinson drug biperiden in pharmaceutical formulations, using a modified cyclodextrin as the chiral selector. Baseline enantioseparation of the racemic compound was achieved in less than 7 min using an uncoated fused silica capillary (50 μm i.d. and 48.5, 40.0 cm, total and effective length, respectively), filled with a background electrolyte consisting of a 50 mM phosphate buffer at pH 3.5 supplemented with 3% (w/v) β-cyclodextrin sulphate and applying a voltage of 20 kV, reversed polarity. Samples were injected by pressure (50 mbar, 90 s) at the cathodic end of the capillary and detection wavelength was 195 nm (bandwidth: 10 nm). A simple and fast pre-treatment procedure allowed the complete extraction of the drug from commercial formulations (sustained release tablets and ampoules for injections) without any interference from the matrix. Good linearity was found in the 1–50 μg/mL concentration range; the limit of quantitation was 1 μg/mL and the limit of detection was 0.4 μg/mL. Precision and accuracy were good, with R.S.D. values always lower than 2.8% and a mean recovery value of 101.1%. The method was suitable for the quality control of biperiden in commercial formulations.     

Nitrofuran antibiotic residues in pork: The FoodBRAND retail survey

Use of nitrofuran drugs in food-producing animals has been prohibited within the EU because they may represent a public health risk. Monitoring compliance with the ban has focused on the detection of protein-bound nitrofuran metabolites which, in contrast to the parent compounds, are stable and persist in animal tissues. As part of the “FoodBRAND” project, an extensive survey of pork was undertaken across 15 European countries. Samples (n = 1500) purchased at retail outlets were analysed for the nitrofuran metabolites AOZ, AMOZ, AHD and SEM using LC–MS/MS determination of nitrobenzaldehyde derivatives. Limits of quantification for the method were 0.1 μg/kg (AOZ, AMOZ), 0.2 μg/kg (SEM) and 0.5 μg/kg (AHD). Of the 1500 samples tested, measurable residues of nitrofuran metabolites were confirmed in 12 samples (0.8% incidence overall) of which 10 samples were purchased in Portugal (AOZ, 0.3 μg/kg; AMOZ, 0.2–0.6 μg/kg) and one sample each in Italy (AMOZ, 1.0 μg/kg) and Greece (AOZ, 3.0 μg/kg).     

Simultaneous separation and preconcentration of trace elements in water samples by coprecipitation on manganese dioxide using D-glucose as reductant for KMnO(4)

A field oriented and economical method of coprecipitation of trace elements like Al, Au, Bi, Cd, Co, Cu, Fe, Mo, Ni, Pb, Pd, Ti, V, W, Zn and REE has been developed. A novel reductant D-glucose, reduces KMnO₄ in solution to form a precipitate of MnO_2. Two liters of clear natural water sample is adjusted to pH 3.5–4.0, and is treated with 10 ml of 1% KMnO₄ and 20 ml of 0.1% D-glucose. The sample is heated at a temperature of 75–80 °C, MnO₂ is formed which coprecipitates the above trace elements. The precipitate is separated by filtration, dissolved in 2 ml of 50% HCl and 2 ml of 30% H₂O₂ and diluted to 25 ml for analysis using AAS and ICP-AES. The recoveries were found to be 96–105%. The preconcentration factor is 80. Limits of determination by the proposed method in natural waters are 1 μg l⁻¹ for Al, Cd, Mo, V, W, Ti and Zn, 5 μg l⁻¹ for Au, Bi, Co, Cu, Fe, Ni, Pb and Pd and 8 μg l⁻¹ for REE. The RSD of the present procedure (n=5) is 8% at 5 μg l⁻¹ level. Twenty water samples can be analyzed by an analyst in an 8-h day.     

Effect of gamma irradiation on caprolactam migration from multilayer polyamide 6 films into food simulants: development and validation of a gas chromatographic method

A GC method to determine caprolactam in water, 15% ethanol, and olive oil food simulants was developed and validated. Linear ranges varied from 0.96 to 642.82 microg/mL for water, 0.64 to 800.32 microg/mL for 15% ethanol, and 1.06 to 1062.34 microg/g for olive oil, with correlation coefficients higher than 0.999. Method precision studies showed RSD values lower than 5.45%, while method accuracy studies showed recovery from 72 to 111% for all simulants. The effect of gamma irradiation on caprolactam migration from multilayer polyamide 6 (PA-6) films intended for cheese into water, 15% ethanol, olive oil, and 3% acetic acid simulants was also studied. For migration assay, non-irradiated and irradiated (12 kGy) films were placed in contact with the simulant and exposed at 40 degrees C for 10 days. The validated method was used to quantify caprolactam migration from multilayer PA-6 films into the simulants, which ranged from 1.03 to 7.59 mg/kg for non-irradiated films, and from 4.82 to 11.32 mg/kg for irradiated films. Irradiation caused almost no changes in caprolactam levels, with the exception of olive oil, which showed an increase in the caprolactam level. All multilayer PA-6 films were in accordance with the requirements of the legislation for caprolactam migration.     

Determination of polybrominated diphenyl ethers in soil by ultrasonic assisted extraction and gas chromatography mass spectrometry

An analytical method for the determination of polybrominated diphenyl ethers (PBDEs) in soil was developed. Soil samples were placed in small glass columns and PBDEs extracted from soil, with a low volume of ethyl acetate (5 mL, 2× 15 min), assisted by sonication. PBDEs were determined by gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode (GC–MS–SIM) and residues were confirmed by their retention times, selected ions and qualifier–target abundance ratios. Recovery studies were performed at 10, 1, 0.1 and 0.05 μg/kg fortification levels, and the recoveries obtained ranged from 81 to 104% with a relative standard deviation between 1 and 9%. The detection limit of the method varied from 2 to 30 pg/g and the quantification limit ranged from 7 to 100 pg/g for the different PBDEs studied. The developed method was linear over the range assayed, 0.01–10 μg/kg with determination coefficients equal or higher than 0.997. The proposed method was used to determine PBDEs levels in soil samples from different areas of Spain and PBDEs were detected in some samples with values ranging from 1.3 to 5.6 μg/kg.     

Quantification of residual nitrite and nitrate in ham by reverse-phase high performance liquid chromatography/diode array detector

Nitrite and nitrate are used as additives in ham industry to provide colour, taste and protect against clostridia. The classical colorimetric methods widely used to determine nitrite and nitrate are laborious, suffer from matrix interferences and involve the use of toxic cadmium. The use of chromatography is potentially attractive since it is more rapid, sensitive, selective and provides reliable and accurate results. A rapid and cost-effective RP-HPLC method with diode array detector was optimized and validated for quantification of nitrites and nitrates in ham. The chromatographic separation was achieved using a HyPurity C18, 5 μm chromatographic column and gradient elution with 0.01 M n-octylamine and 5 mM tetrabutylammonium hydrogenosulphate to pH 6.5. The determinations were performed in the linear range of 0.0125–10.0 mg/L for nitrite and 0.0300–12.5 g/L for nitrate. The detection limits were 0.019 and 0.050 mg/kg, respectively. The reliability of the method in terms of precision and accuracy was evaluated. Coefficients of variation lower than 2.89% and 5.47% were obtained for nitrite and nitrate, respectively (n = 6). Recoveries of residual nitrite/nitrate ranged between 93.6% and 104.3%. Analysis of cooked and dried ham samples was performed, and the results obtained were in agreement with reference procedures.     

Application of ion-exchange cartridge clean-up in food analysis I. Simultaneous determination of thiabendazole and imazalil in citrus fruit and banana using high-performance liquid chromatography with ultraviolet detection

A simple, rapid and reproducible analytical method for thiabendazole (TBZ) and imazalil (IMA) in citrus fruit and banana has been developed. The method involves the use of an ion-exchange cartridge for sample clean-up followed by ion-pair high-performance liquid chromatography with ultraviolet detection. The recoveries of TBZ and IMA from citrus fruits spiked at levels of 10 μg/g and 5 μg/g were in the range of 94–98% and 93–98% with coefficients of variation of 0.5–2.2% and 1.6–2.7%, respectively. The recoveries of TBZ and IMA from banana spiked at levels of 3 μg/g and 2 μg/g were 94% and 94% with coefficients of variation 1.1% and 4.9%, respectively. The detection limits for TBZ and IMA were 0.1 μg/g in citrus fruit and 0.05 μg/g in banana.     

Photo-luminescence of Risø B3 and PVB films for application in radiation dosimetry

Risø B3 film dosimeters (23 μm) prepared from poly(vinyl butyral) (PVB) incorporating pararosaniline cyanide, as the radiation-sensitive element and PVB films (25 μm) prepared from PVB without any additives are investigated for γ-radiation measurement using spectrofluorimetry based on their emission properties. The unirradiated Risø B3 film when excited at 554 nm shows an emission band at 602 nm while PVB film shows an emission band at 305 nm when excited at 235 nm wavelength. The fluorescence intensity of both emission bands decreases with the increase of absorbed dose due to the damage caused by ionizing radiation. The useful dose range of Risø B3 film extends up to 120 kGy while that of PVB film extends up to 60 kGy. The response of Risø B3 film increases with the increase of relative humidity during irradiation while that of PVB has less effect in the humidity range of 20–70%. The percent uncertainty associated with the measurement of the dose response was found to be ±3% (1σ) for both films. Risø B3 and PVB films show good post-irradiation stability in dark and indirect daylight where the deviation in the response overall a 2-month storage period was found to be ±5% for Risø B3 and ±2% for PVB.     

HPLC determination of Vitamin D(3) and its metabolite in human plasma with on-line sample cleanup

A HPLC method with automated column switching and UV-diode array detection is described for the simultaneous determination of Vitamin D₃ and 25-hydroxyvitamin D₃ (25-OH-D₃) in a sample of human plasma. The system uses a BioTrap precolumn for the on-line sample cleanup. A sample of 1 ml of human plasma was treated with 2 ml of a mixture of ethanol–acetonitrile (2:1 (v/v)). Following centrifugation, the supernatant was evaporated to dryness under a stream of dry and pure nitrogen. The residue was reconstituted in 250 μL of a solution of methanol 5 mmol l⁻¹ phosphate buffer, pH 6.5 (4:1 (v/v)), and a 200 μl aliquot of this solution was injected onto the BioTrap precolumn. After washing during 5 min with a mobile phase constituted by a solution of 6% acetonitrile in 5 mmol l⁻¹ phosphate buffer, pH 6.5 (extraction mobile phase), the retained analytes were then transferred to the analytical column in the backflush mode. The analytical separation was then performed by reverse-phase chromatography in the gradient elution mode with the solvents A and B (Solvent A: acetonitrile–phosphate buffer 5 mmol l⁻¹, pH 6.5; 20:80 (v/v); solvent B: methanol–acetonitrile–tetrahydrofuran, 65:20:15 (v/v)). The compounds of interest were detected at 265 nm. The method was linear in the range 3.0–32.0 ng ml⁻¹ with a limit of quantification of 3.0 ng ml⁻¹. Quantitative recoveries from spiked plasma samples were between 91.0 and 98.0%. In all cases, the coefficient of variation (CV) of the intra-day and inter-day-assay precision was ≤2.80%. The proposed method permitted the simultaneous determination of Vitamin D₃ and 25-OH-D₃ in 16 min, with an adequate precision and sensitivity. However, the overlap of the sample cleanup step with the analysis increases the sampling frequency to five samples h⁻¹. The method was successfully applied for the determination of Vitamin D₃ and 25-OH-D₃ in plasma from 46 female volunteers, ranging from 50 to 94 years old. Vitamin D₃ and 25-OH-D₃ concentrations in plasma were found from 4.30–40.70 ng ml⁻¹ (19.74 ± 9.48 ng ml⁻¹) and 3.1–36.52 ng ml⁻¹ (7.13 ± 7.80 ng ml⁻¹), respectively. These results were in good agreement with data published by other authors.     

A novel method for the spectrophotometric determination of nitrite in water

A rapid, simple, selective and sensitive method for the spectrophotometric determination of nitrite in water has been developed and optimum reaction conditions along with other analytical parameters have been evaluated. Nitrite reacts with barbituric acid in acidic solution to give the nitroso derivative, violuric acid. At analytical wavelength of 310 nm, Beer's law is obeyed over the concentration range 0.00–3.22 ppm of nitrite. The molar absorptivity is 15330 ± 259.7 (95%) with pooled standard deviation of 355.57 and R.S.D. of 2.32%. As well as the method is sensitive (2.99 × 10⁻³ μg NO₂ cm⁻²) and selective, it tolerates most of the potential interferents. It has been successfully applied to nitrite determination in natural waters by use of a calibration graph with determination limit of 1.66 μg NO₂ in 100 mL working solution corresponding to minimum 9.5 ppb NO₂–N in water samples. Lower concentrations of nitrite (3.0 μg NO₂/L sample) is precisely analyzed by using the method of dilution with sample, with R.S.D. of lower than 0.5%. The results were compared with standard N-(1-naphtyl)ethylenediamine dihydrochloride method and very good agreement between the data was observed. The method can easily be applied in the field.     

Determination of type A trichothecenes by high-performance liquid chromatography with coumarin-3-carbonyl chloride derivatisation and fluorescence detection

A method for the analysis of type A trichothecenes T-2 toxin, HT-2 toxin, neosolaniol and diacetoxyscirpenol by high-performance liquid chromatography with fluorescence detection using coumarin-3-carbonyl chloride has been developed. Different parameters concerning the analytical procedure such as stability of both the reagent and derivatised analytes, time and temperature of the derivatisation reaction, were studied and optimised. Three different clean-up procedures (solid-phase extraction with silica gel or C-18 cartridges, and liquid–liquid partition between toluene and dihydrogen phosphate buffer) were tested in order to remove the excess reagent peaks. The last procedure gave the best results when the buffer pH was 3–5.5, and is therefore recommended. Separations were performed on a stainless steel LiChrospher 100 C-18 reversed-phase column with pre-column of the same phase. The mobile phase was acetonitrile/water (65:35, v/v) containing 0.75% acetic acid at a flow-rate of 1.0 ml/min. The proposed method provides good separation between the four trichothecenes and good reproducibility (RSD of calibration standards <5%). The limits of detection of the studied trichothecenes at a signal-to-noise ratio of 3:1, with an injection volume of 20 μl were 10 ng/g sample for T-2 toxin and about 15 ng/g sample for the remaining mycotoxins. The calibration curve was linear between 10 and 2000 ng for the four trichothecenes assayed. The method was applied to the analysis of these mycotoxins in fungal cultures (corn and rice) of Fusarium sporotrichioides, and is also perfectly suitable for the quantification of type A trichothecenes in contaminated cereals.     

Evaluation of solid-phase micro-extraction coupled to gas chromatography-mass spectrometry for the headspace analysis of volatile compounds in cocoa products

The aroma profile of cocoa products was investigated by headspace solid-phase micro-extraction (HS-SPME) combined with gas chromatography–mass spectrometry (GC–MS). SPME fibers coated with 100 μm polydimethylsiloxane coating (PDMS), 65 μm polydimethylsiloxane/divinylbenzene coating (PDMS-DVB), 75 μm carboxen/polydimethylsiloxane coating (CAR-PDMS) and 50/30 μm divinylbenzene/carboxen on polydimethylsiloxane on a StableFlex fiber (DVB/CAR-PDMS) were evaluated. Several extraction times and temperature conditions were also tested to achieve optimum recovery. Suspensions of the samples in distilled water or in brine (25% NaCl in distilled water) were investigated to examine their effect on the composition of the headspace. The SPME fiber coated with 50/30 μm DVB/CAR-PDMS afforded the highest extraction efficiency, particularly when the samples were extracted at 60 °C for 15 min under dry conditions with toluene as an internal standard. Forty-five compounds were extracted and tentatively identified, most of which have previously been reported as odor-active compounds. The method developed allows sensitive and representative analysis of cocoa products with high reproducibility. Further research is ongoing to study chocolate making processes using this method for the quantitative analysis of volatile compounds contributing to the flavor/odor profile.     

Spectrophotometric determination of terfenadine in pharmaceutical preparations by charge-transfer reactions

A simple, rapid and accurate method for the spectrophotometric determination of terfenadine has been developed. The proposed method based on the charge-transfer reactions of terfenadine, as n-electron donor, with 7,7,8,8-tetracyanoquinodimethane (TCNQ), tetracyanoethylene (TCNE), 2,3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ) or 2,5-dichloro-3,6-dihydroxy-1,4-benzoquinone (chloranilic acid, p-CLA) as π-acceptors to give highly colored complexes. The experimental conditions such as reagent concentration, reaction solvent and time have been carefully optimized to achieve the highest sensitivity. Beer's law is obeyed over the concentration ranges of 3–72, 3–96, 12–168 and 24–240 μg mL⁻¹ terfenadine using TCNQ, TCNE, DDQ and p-CLA, respectively, with correlation coefficients 0.9999, 0.9974, 0.9997 and 0.9979 and detection limits 0.3, 0.4, 2.6 and 12.3 μg mL⁻¹, for the reagents in the same order. DDQ and p-CLA react spontaneously with terfenadine to give colored complexes that can be applied for the flow injection analysis of terfenadine in the concentration ranges 2.4–120 and 24–240 μg with correlation coefficients 0.9990 and 0.9985 and detection limits 0.8 and 2.7 μg for DDQ and p-CLA, respectively, in addition to the high sampling through output of 40 sample h⁻¹.     

Determination of nanomolar concentrations of phosphate in freshwaters using flow injection with luminol chemiluminescence detection

A simple and rapid flow injection (FI) method is reported for the determination of phosphate (as molybdate reactive P) in freshwaters based on luminol chemiluminescence (CL) detection. The molybdophosphoric heteropoly acid formed by phosphate and ammonium molybdate in acidic conditions generated chemiluminescence emission via the oxidation of luminol. The detection limit (3× standard deviation of blank) was 0.03 μg P l⁻¹ (1.0 nM), with a sample throughput of 180 h⁻¹. The calibration graph was linear over the range 0.032–3.26 μg P l⁻¹ (r²=0.9880) with relative standard deviations (n=4) in the range 1.2–4.7%. Interfering cations (Ca(II), Mg(II), Ni(II), Zn(II), Cu(II), Co(II), Fe(II) and Fe(III)) were removed by passing the sample through an in-line iminodiacetate chelating column. Silicate interference (at 5 mg Si l⁻¹) was effectively masked by the addition of tartaric acid and other common anions (Cl⁻, SO₄²⁻, HCO₃⁻, NO₃⁻ and NO₂⁻) did not interfere at their maximum admissible concentrations in freshwaters. The method was applied to freshwater samples and the results (26.1±1.1–62.0±0.4 μg P l⁻¹) were not significantly different (P=0.05) from results obtained using a segmented flow analyser method with spectrophotometric detection (24.4±4.45–84.0±16.0 μg P l⁻¹).     

On-line microwave sample pretreatment for the determination of mercury in blood by flow injection cold vapor atomic absorption spectrometry

A method for on-line treatment of whole blood in a microwave oven and determination of mercury by flow injection cold vapor atomic absorption spectrometry was developed. After dilution of the whole blood and addition of oxidant, all further treatment and measurement were performed automatically, on-line. Recoveries of five mercury compounds were complete. Good agreement between measured and recommended values of mercury in whole blood reference materials was obtained. Measured mercury values also agreed with results from other accepted methods. Sample throughput was about 45 measurements/hr. Detection limit (3s) in diluted sample was 0.1 μg/l corresponding to 1μg/l Hg in whole blood. The RSD value at 0.5 μg/l Hg in the diluted sample was 6–7% (11 measurements and 0.5 ml sample volume). Mercury concentrations between 1 and 150 μg/l in whole blood can be measured using this method. For three replicate measurements, 0.5 ml of whole blood is required.     

Critical study of fluorimetric determination of selenium in urine

Different steps for the fluorimetric determination of Se in urine have been investigated. A HNO₃---HClO₄ (4:1) mixture is useful for urine digestion, and reduction of Se(VI) to Se(IV) is effectively carried out with HCl (6M). Selenium(VI) present after the digestion process constitutes 14.5–36.6% of total Se. An optimum pH of 1.80±0.05 and the addition of 1 ml of 2,3-diaminonaphthalene (DAN) (0.1%, w/v) are established in the formation of Se—DAN complex. Heating to 60°C, a time of incubation of 15 min is recommended to assure the complete formation of Se—DAN complex. A volume of 5 ml of cyclohexane and vigorous shaking for 45 sec is necessary for the extraction process. With this optimized method, the detection limit of selenium was 0.82 μg/l., within-day precision for a 50.0 μg/l. standard solution and urine (27.3 μg/l.) were 2.4 and 2.7% and between-day for the urine was 3.9% (33.9 μg/l.). Analytical recovery of 0.5 ml of Se standard (250 μg/l.) added to 1 ml of urine was 99.9±2.9% (95.8–104.4, n = 12). Normal levels of selenium excretion in urine obtained from healthy people were 27.9±8.7 μg/day (13.2–44.1), not observing significant differences (P < 0.05) between sexes.     

Polarographic chemometric determination of zinc and nickel in aqueous samples

Polarographic chemometric methods were applied to the determination of zinc and nickel in aqueous solutions previously acidified with 0.1 M acetate buffer (pH 4.2). The studied methods are multivariate methods including classical least squares (CLS), principal component regression (PCR) and partial least squares (PLS); derivative ratio methods (first, ¹D and second, ²D derivative ratio). A comparative study was considered. The studied chemometric methods do not need the presence of any reduction potential shift reagent in spite of the great overlap between the two metals polarograms. A training set consisting of 10 binary mixture solutions in the possible combinations containing 0.13–9.30 μg/ml Zn(II) and 0.20–12.25 μg/ml Ni(II) was used to develop the chemometric calibrations (CLS, PCR and PLS). A validation set containing the synthetic mixtures in the range of 0.29–9.00 μg/ml for Zn(II) and 0.30–11.60 μg/ml for Ni(II) was used to validate the multivariate calibrations. Same mixtures were used to develop the derivative ratio methods. The polarograms were recorded and their current values were measured within the potential range −920 to −1052 mV at 2 mV intervals. The mean percentage recoveries obtained using CLS, PCR and PLS were found to be 99.5 ± 1.5%, 100.0 ± 1.1% and 100.0 ± 1.0% for Zn(II) and 99.4 ± 1.3%, 99.7 ± 1.2% and 99.9 ± 1.0% for Ni(II), respectively. The mean percentage recoveries obtained using ¹D at −950 mV, ¹D at −1010 mV, ¹D at −950 mV–¹D at −1010 mV and ²D at −986 mV for Zn(II) were found to be 99.7 ± 1.2%, 99.2 ± 1.6%, 99.4 ± 1.4% and 99.4 ± 1.4%; and using ¹D at −1030 mV and ²D at −1010 mV for Ni(II) were found to be 100.5 ± 1.3% and 100.4 ± 1.3%, respectively. Interferences due to the presence of Cd, Co, Pb, Fe, Mn, Ca, Mg, Cu and Al were studied. The applicability of the proposed methods was assessed through the determination of both metals in tap drinking-water. Samples were subjected if required up to a 20-fold preconcentration step by microwaving in pyrex vessels. The results were compared with those obtained using the zincon and the heptoxime colorimetric reference methods for the determination of zinc and nickel, respectively.