Facile in situ synthesis of nickel/cellulose nanocomposites: mechanisms,properties and perspectives

Nickel/cellulose nanocomposites with tunable magnetic behavior and electrical conductivity were fabricated by a facile in situ synthesis route with aqueous NaOH/urea solution as the solvent to dissolve and regenerate cellulose. It was found that Ni particles are uniformly dispersed in and immobilized by cellulose matrix, which indicates that regenerated cellulose fibers with coarse surface might act as templates to modulate the growth of Ni nanoparticles. Moreover, the size and morphology of Ni nanoparticles as well as the magnetic and conductive properties of Ni/cellulose nanocomposites is dependent on the concentration of Ni²⁺ in NaOH/urea aqueous solution. With an increase in the concentration of Ni²⁺ from 0.2 to 1.0 mol/L, the values of saturation magnetization increased from 16.6 to 38.5 emu/g, while the resistance decreased from 10⁶ to 10^?2 Ω cm. Particularly, multi-layer sample exhibits good absorption capacity and an additional effective bandwidth in the low-frequency region, showing promising potential as candidate electromagnetic functional fabric and cloth.     

A nanocomposite containing Prussian Blue,platinum nanoparticles and polyaniline for multi-amplification of the signal of voltammetric immunosensors: highly sensitive detection of carcinoma antigen 125

The authors describe a method for signal amplification of label-free voltammetric immunosensors. A glassy carbon electrode (GCE) was modified with Prussian Blue-platinum nanoparticles (PB-PtNPs) as a redox-active species that gives a strong amperometric signal at 0.18 V (vs. Ag/AgCl). Benefitting from the excellent electrical conductivity and the strong catalytic activity to H₂O₂, the modified GCE gives a strongly enhanced signal. The PB-PtNPs were incorporated into a polyaniline (PANI) hydrogel to further enhance the signal. The signal response of the PB-PtNP-PANI/GCE is larger by a factor of 7.6 than that of PB-PtNP/GCE. In order to further improve electrical conductivity and immobilize antibody, gold nanoparticles (AuNPs) were deposited on the surface of the PB-PtNP-PANI hydrogel. The AuNP-PB-PtNP-PANI hydrogel nanocomposite on the GCE was used in an immunosensor for the model analyte carcinoma antigen 125 (CA125), a biomarker for epithelial ovarian cancer, by immobilizing the respective antibody on the modified GCE. A linear response found for the 0.01 to 5000 U mL^?1 CA125 concentration range, with a detection limit of 4.4 mU mL^?1 (at an S/N ratio of 3). The electrochemical sensitivity is as high as 119.76 μA·(U/mL)^?1·cm^?2. The detection of CA125 in human serum showed satisfactory accuracy compared to a commercial chemiluminescent microparticle immunoassay (CMIA).

Open image in new window

Graphical abstract Schematic of a nanocomposites consisting of gold nanoparticles, Prussian Blue, platinum nanoparticles and polyaniline hydrogel as a signal multi-amplification sensing substrate for the ultrasensitive immuno detection of carcinoma antigen 125 (CA125).

     

Nanocomposite Hydrogel of Pd@ZIF-8 and Laponite®: Size-Selective Hydrogenation Catalyst under Mild Conditions

The composite hydrogel of a nanoscale metal–organic framework (NMOF) and nanoclay has emerged as a new soft-material with advanced properties and applications. Herein, we report a facile synthesis of a hydrogel nanocomposite by charge-assisted self-assembly of Pd@ZIF-8 nanoparticles with Laponite^® nanoclay which coat the surface of Pd@ZIF-8 nanoparticles. Such surface coating significantly enhanced the thermal stability of the ZIF-8 compared to the pristine framework. Further, the Pd@ZIF-8+LP hydrogel nanocomposite shows better size-selective catalytic hydrogenation of olefins than Pd@ZIF-8 nanoparticles based on selective diffusion of the substrate.     

Ultra-sensitive electrochemical DNA biosensor based on signal amplification using gold nanoparticles modified with molybdenum disulfide,graphene and horseradish peroxidase

We have developed an ultra-sensitive electrochemical DNA biosensor by assembling probe ssDNA on a glassy carbon electrode modified with a composite made from molybdenum disulfide, graphene, chitosan and gold nanoparticles. A thiol-tagged DNA strand coupled to horseradish peroxidase conjugated to AuNP served as a tracer. The nanocomposite on the surface acts as relatively good electrical conductor for accelerating the electron transfer, while the enzyme tagged gold nanoparticles provide signal amplification. Hybridization with the target DNA was studied by measuring the electrochemical signal response of horseradish peroxidase using differential pulse voltammetry. The calibration plot is linear in the 5.0?×?10^?14 and 5.0?×?10^?9 M concentration range, and the limit of detection is 2.2?×?10^?15 M. The biosensor displays high selectivity and can differentiate between single-base mismatched and three-base mismatched sequences of DNA. The approach is deemed to provide a sensitive and reliable tool for highly specific detection of DNA.

Designing and fabrication of a novel gold nanocomposite structure: application in electrochemical sensing of bisphenol A

In this article, a highly sensitive electrochemical sensor is introduced for direct electro-oxidation of bisphenol A (BPA). The novel nanocomposite was prepared based on multi-walled carbon nanotube/thiol functionalised magnetic nanoparticles (Fe₃O₄-SH) as an immobilisation platform and gold nanoparticles (AuNPs) as an amplifying electrochemical signal. The chemisorbed AuNPs exhibited excellent electrochemical activity for the detection of BPA. Some analysing techniques such as Fourier transform infrared spectroscopy, field emission scanning electron microscopy, transmission electron microscopy and energy-dispersive x-ray diffraction exposed the formation of nanocomposite. Under optimum conditions (pH 9), the sensor showed a linear range between 0.002–240 μM, with high sensitivity (0.25 μA μM^?1) along with low detection limit (6.73 × 10^?10 M). Moreover, nanocomposites could efficiently decrease the effect of interfering agents and remarkably enhance the utility of sensor at detection of BPA in some real samples.     

Silver modified magnetic carbon nanotubes composite as a selective solid phase extractor for preconcentration and determination of trace mercury ions in water solution

A magnetic composite of silver/iron oxides/carbon nanotubes (Ag/Fe₃O₄/CNTs) was synthesized and used as an adsorbent for the preconcentration of mercury ions in water solutions at room temperature (25°C) in this study. The silver nanoparticles were supported on the magnetic CNTs. The modification enabled the composite had not only a high adsorption capacity for mercury ions (Hg²⁺) but also the magnetic isolation properties. A fast, sensitive, and simple method was successfully developed for the preconcentration and determination of trace amount of Hg²⁺ in water using the synthesized nanocomposite as adsorbent. The mercury concentration was determined by an atomic fluorescence spectrometer (AFS). The experimental conditions such as pH value, extraction temperature, extraction time, sample volume, eluent composition and concentration, sorbent amount, and coexisting ions were investigated for the optimization. A 500 mL of sample volume resulted in a preconcentration factor of 125. When a 200 mL of sample was employed, the limit of detection for Hg²⁺ was as low as 0.03 ng mL^?1with relative standard deviation of 4.4% at 0.1 ng mL^?1 (n = 7). The ease of synthesis and separation, the good adsorption capacity, and the satisfactory recovery will possibly make the composite an attractive adsorbent for the preconcentration of ultratrace Hg²⁺ in waters.     

New method for preparation of polyoxometalate-capped gold nanoparticles, and their assembly on an indium-doped tin oxide electrode

Functionalized gold nanoparticles capped with polyoxometalates were prepared by a simple photoreduction technique where phosphododecamolybdates serve as reducing reagents, photocatalysts, and as stabilizers. TEM images of the resulting gold nanoparticles show the particles to have a relative narrow size distribution. Monolayer and multilayer structures of the negatively charged capped gold nanoparticles were deposited on a poly(vinyl pyridine)-derivatized indium-doped tin oxide (ITO) electrode via the layer-by-layer technique. The surface plasmon resonance band of the gold nanoparticles displays a blue shift on the surface of the ITO electrode. This is due to the substrate-induced charge redistribution in the gold nanoparticles and a change in the electromagnetic coupling between the assembled nanoparticles. The modified electrode exhibits the characteristic electrochemical behavior of surface-confined phosphododecamolybdate and excellent electrocatalytic activity. The catalysis of the modified electrode towards the model compound iodate was systematically studied. The heterogeneous catalytic rate constant for the electrochemical reduction of iodate was determined by chronoamperometry to be ca. 1.34?×?10⁵ mol^?1·L·s^?1. The amperometric method gave a linear range from 2.5?×?10^?6 to 1.5?×?10^?3 M and a detection limit of 1.0?×?10^?6 M. We believe that the functionalized gold nanoparticles prepared by this photoreduction technique are advantageous in terms of fabrication of sensitive and stable redox electrodes.

Enhanced zinc ion transport in gel polymer electrolyte: effect of nano-sized ZnO dispersion

The effect of the dispersion of zinc oxide (ZnO) nanoparticles in the zinc ion conducting gel polymer electrolyte is studied. Changes in the morphology/structure of the gel polymer electrolyte with the introduction of ZnO particles are distinctly observed using X-ray diffraction and scanning electron microscopy. The nanocomposites offer ionic conductivity values of >10^?3 S cm^?1 with good thermal and electrochemical stabilities. The variation of ionic conductivity with temperature follows the Vogel–Tamman–Fulcher behavior. AC impedance spectroscopy, cyclic voltammetry, and transport number measurements have confirmed Zn²⁺ ion conduction in the gel nanocomposites. An electrochemical stability window from ?2.25 to 2.25 V was obtained from voltammetric studies of nanocomposite films. The cationic (i.e., Zn²⁺ ion) transport number (t ₊) has been found to be significantly enhanced up to a maximum of 0.55 for the dispersion of 10 wt.% ZnO nanoparticles, indicating substantial enhancement in Zn²⁺ ion conductivity. The gel polymer electrolyte nanocomposite films with enhanced Zn²⁺ ion conductivity are useful as separators and electrolytes in Zn rechargeable batteries and other electrochemical applications.     

Graphene/poly(ortho-phenylenediamine) nanocomposite material for electrochemical supercapacitor

Reduced graphene oxide was synthesized by simple chemical processing of graphite. Electron microscopy investigations of synthesized graphene showed slightly folded transparent sheets with a few square micrometers dimension. Poly(ortho-phenylenediamine)/graphene/Pt electrode was electrochemically fabricated in a 2.0-M H₂SO₄ solution by means of multiple potential cycling. Due to the catalytic effect of graphene on the oxidative electropolymerization of ortho-phenylenediamine, the ortho-phenylenediamine/graphene (PoPD/GR) nanocomposite showed greatly enhanced electrical properties and excellent capacitive behavior. Electrochemical impedance spectroscopy, galvanostatic charge/discharge curves, and voltammetric investigations revealed that PoPD/GR nanocomposite represented good capacitive behavior with a specific capacitance as high as 308.3 F g^?1 at 0.1 A g^?1. It is almost three times higher than that of pure graphene (111.7 F g^?1). In addition, the nanocomposite electrode retained more than 99 % of the initial capacity after 1,500 cycles at a current density of 1 A g^?1.     

Photodegradation of 2-nitrophenol catalyzed by CoO, CoS and CoO/CoS nanoparticles

The nanoparticles of CoO, CoS and CoO/CoS composite are synthesized using precipitation method. The X-ray diffraction, UV–Vis absorption spectroscopy, energy dispersive X-ray spectroscopy, scanning electron microscopy and FT-IR spectroscopy are used to characterize the prepared nanoparticles. The EDX analysis shows the formation of CoO_0.67S_0.33 composite. The XRD pattern indicates the hexagonal structure for nanocomposite. The formation of Co–O and Co–S bonds is confirmed by FT-IR spectra. The band-gap energies of 2.97, 3.06 and 2.91 eV are obtained from UV–Vis spectra of CoO, CoS and CoO/CoS nanoparticles, respectively. The results of photodegradation of 2-nitrophenol show that the photoreactivity order of nanocatalysts is CoO/CoS > CoO > CoS. The pseudo first-order kinetic rate constants of 6.4 × 10^?3, 4.3 × 10^?3 and 12.2 × 10^?3 min^?1 are obtained for CoO, CoS and CoO/CoS nanoparticles, respectively, at photodegradation reaction conditions of pH 10, 30 mg/L of 2-NP and 1.3 g/L of the catalyst. The proposed nanocomposite shows an acceptable reusability and stability against photocorrosion in four-cycle photodegradation experiments.     

Study of catalytic action of micro-particles and synthesized nanoparticles of CuS on cellulose pyrolysis

The catalytic action of copper sulfide (CuS) micro-particles and as-synthesized nanoparticles was studied on cellulose pyrolysis. The market procured CuS powder was used as micro-particles without any treatment. The CuS nanoparticles were synthesized at ambient temperature by simple wet chemical technique. Before using the micro-particles and nanoparticles for catalytic study, they were comprehensively characterized. The thermal analysis including catalytic properties of both the micro-particles and nanoparticles of CuS on cellulose pyrolysis was studied employing thermogravimetric (TG), differential thermogravimetric, and differential thermal analysis techniques. Prior to the study as catalyst in cellulose pyrolysis, the CuS micro- and nanoparticles were characterized by thermal analysis in inert atmosphere. The TG curves showed two steps and five steps decomposition having total mass loss of 29 and 42 % in case of CuS micro- and as-synthesized nanoparticles, respectively. The catalytic study in cellulose pyrolysis showed that the decomposition commences at temperature 295 °C for pure cellulose, 270 °C for cellulose mixed with 3 % CuS micro-particles and 205 °C for cellulose mixed with 3 % CuS nanoparticles. It clearly showed that the decomposition starting temperature decreased by 65 °C in case of cellulose mixed with CuS nanoparticles compared to cellulose mixed with CuS micro-particles. Thus, CuS nanoparticles act as better catalyst then CuS micro-particles in cellulose pyrolysis. The obtained results are deliberated in details.     

Biocompatible Magnetic Hydrogel Nanocomposite Based on Carboxymethylcellulose: Synthesis,Cell Culture Property and Drug Delivery

In this report, the synthesis of a novel biocompatible magnetic hydrogel nanocomposite based on carboxymethyl cellulose (CMC), as an eco-friend, biocompatible and green polysaccharide, is described via a facile one pot approach using magnetic iron oxide nanoparticles (MIONs) as a crosslinker. The structure of the prepared MION–CMC hydrogel nanocomposite was examined by various analytical techniques such as FTIR spectroscopy, TGA thermal analysis, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM). The MIONs were generated in situ during the hydrogel formation with an average diameter size of 10 nm and a narrow size distribution. The sample was superparamagnetic with large saturation magnetization at room temperature. MION–CMC hydrogel nanocomposite showed a good ability for releasing of doxorubicin as an anticancer drug at pH 7 with case II (relaxational) transport mechanism. This outcome demonstrated that MION–CMC hydrogel nanocompositeis an attractive biocompatible candidate for widespread biomedical applications, particularly in controlled drug-targeting delivery.     

Polyaniline encapsulated silicon nanocomposite as high-performance anode materials for lithium ion batteries

Polyaniline encapsulated silicon (Si/PANI) nanocomposite as anode materials for high-capacity lithium ion batteries has been prepared by an in situ chemical polymerization of aniline monomer in the suspension of Si nanoparticles. The obtained Si/PANI nanocomposite demonstrates a reversible specific capacity of 840 mAh g^?1 after 100 cycles at a rate of 100 mA g^?1 and excellent cycling stability. The enhanced electrochemical performance can be due to that the polyaniline (PANI) matrix offers a continuous electrically conductive network as well as enhances the compatibility of electrode materials and electrolyte as a result of suppressing volume stress of Si during cycles and preventing the agglomeration of Si nanoparticles.     

A facile synthesis of boron nanostructures and investigation of their catalytic activity for thermal decomposition of ammonium perchlorate particles

In this research, ultrasound irradiation as a simple method was used to produce boron nanostructures. Reaction conditions such as boron concentration and sonication time show important roles in the size, morphology and growth process of the final products. The boron nanostructures (nanoparticles and nanorods) were characterized by scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction, small-angle X-ray scattering and inductively coupled plasma atomic emission spectroscopy techniques. Primary evaluation of results showed that nanoparticles and nanorods of boron successfully have been prepared with 25–40 and 50–100 nm average particle size, respectively. These nanostructures (nanoparticles and nanorods) were studied as an additive for promoting the thermal decomposition of ammonium perchlorate (AP) particles. Thermochemical decomposition behaviors of treated samples were characterized by thermal gravimetric analysis and differential scanning calorimetry techniques. Also, the kinetic parameters of thermal decomposition processes of pure and treated samples were obtained by nonisothermal methods proposed by Kissinger and Ozawa. However, boron nanoparticles with the smallest average particle size (25–40 nm) have the most significant catalytic effect including the decrease in decomposition temperature of AP + B nanocomposite by 100 °C, increase in the heat of decomposition from 580 to 1354 J g^?1 and decrease in activation energy from 207 to 110 kJ mol^?1.     

A novel method for D-arabinitol determination based on a nano-structured sensing film by one-step electrodeposition

Copper nanoparticles (Cu-NPs) were incorporated into chitosan hydrogel to form a film on the surface of a glassy carbon electrode (GCE) leading to a sensing element for D-arabinitol with excellent oxidative catalytic activity. The electrochemical response to D-arabinitol was studied by cyclic voltammetry and differential pulse voltammetry. Operational parameters affecting the response were examined and optimized, and a simple and sensitive method was established for the determination of D-arabinitol. Response is linear in the concentration range from 10 μmol·L^?1 to 10 mmol·L^?1, and the limit of detection is 1.0 μmol·L^?1. The method may be combined with separation techniques in order to analyze for the ratio of D- and L-arabinitol which is a diagnostic marker for candidiasis.     

Synthesis of multiresponsive β‐cyclodextrin nanocomposite through surface RAFT polymerization for controlled drug delivery

In this study, a unique magnetic, pH, and thermo‐responsive hydrogel nanocomposite was synthesized via surface reversible addition fragmentation chain transfer (RAFT) copolymerization of acrylic acid (AA) and N‐isopropyl acrylamide (NIPAM) in the presence of magnetic β‐cyclodextrin (β‐CD). The nanocomposite demonstrated a pH‐responsiveness behavior at pHs 3 and 9. Moreover, swelling behaviors of nanocomposite were measured in solutions with various temperatures. Furthermore, the nanocomposites exhibited high swelling capacity by applying an external magnetic field because of the presence of Fe₃O₄ nanoparticles in the polymer structure. Besides, the doxorubicin (DOX) loading and releasing behaviors of the hydrogel nanocomposites were studied because of the stimuli‐responsive properties of the synthesized carriers. The adsorption of DOX obeyed a pseudo‐second‐order model and fitted well to the Langmuir isotherm model with the maximum adsorption capacity uptake of 291 mg g^?1. In conclusion, the hydrogel nanocomposites were found to be as potential nanocarriers for use in controlled release applications.     

Synthesis and characterization of (hydroxypropyl)cellulose/TiO2 nanocomposite films

A new method of synthesis of TiO₂ nanoparticles as well as preparation of the organic–inorganic hybrid nanocomposite films of (hydroxypropyl)cellulose (HPC)/TiO₂ is presented. At the first stage, the oxotitanium hydrogel phase was obtained by the mineralization of (tetra‐isopropyl)orthotitanate (TIPT) modified by the methacrylic acid (MAA) in 15 wt% solution of H₂O₂ at room temperature and subsequent annealing at the temperature of 85°C. The crystallization of the nanoparticles of TiO₂ was conducted at the oxotitanium hydrogel phase at temperatures around 120°C in the closed vessel. Nanocomposite hybrid films were prepared by the casting method from a solution of HPC and TiO₂ nanoparticles in the water. The films of nanocomposite with 10 µm thickness are transparent to visible light and have a lower glass transition temperature compared with HPC in the bulk. This shift of the glass transition is interpreted in terms of packing density of HPC in the interface of HPC nanocomposite with TiO₂. The X‐ray diffraction pattern of the nanocomposite film suggests a lower amount of mesomorphic phase of HPC in the composite compared with HPC in the bulk. Copyright © 2007 John Wiley & Sons, Ltd.     

Electrochemical Detection of Epinephrine Using an L-Glutamic Acid Functionalized Graphene Modified Electrode

The development and application of an L-glutamic acid functionalized graphene nanocomposite, modified glassy carbon electrode are reported for the determination of epinephrine. The properties of the nanocomposite were characterized by scanning electron microscopy, ultraviolet-visible absorption spectroscopy, infrared spectroscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. The modified electrode had high sensitivity and strongly catalytic activity for the detection of epinephrine. A linear relationship between the epinephrine concentration and the current response was obtained in the range of 1 × 10^?7 M to 1 × 10^?3 M by differential pulse voltammetry with a limit of detection of 3 × 10^?8 M. The modified electrode was employed to determine epinephrine in urine with satisfactory results.     

Synthesis of 2-mercaptobenzothiazole/magnetic nanoparticles modified multi-walled carbon nanotubes for simultaneous solid-phase microextraction of cadmium and lead

This study describes the successful sequential modification of multi-walled carbon nanotube (MWCNT) by Fe₃O₄ magnetic nanoparticles and 2-mercaptobenzothiazole (MBT) followed by its application as a novel sorbent for simultaneous magnetic solid phase microextraction of lead and cadmium. Fourier transform infrared spectroscopy and scanning electron microscopy were employed to confirm the chemical surface modification of the MWCNT. The ions retained on the 2-MBT/magnetic nanoparticles modified MWCNTs were eluted with 1.0 mL of nitric acid (0.8 mol L^?1) in methanol solution and determined by the flame atomic absorption spectrometry. All parameters affecting the extraction condition were thoroughly investigated and optimised. Under the optimised condition preconcentration factor of 150.0, enhancement factors of 149.0 and 149.2 and limits of detection of 0.21 and 0.01 µg L^?1 were achieved for lead and cadmium, respectively. Using the prepared magnetic nanocomposite, the possible interference of other common ions associated with lead and cadmium determination was effectively avoided and the method was successfully applied to the simultaneous determination of the target ions in various environmental water samples.     

Magneto-responsive hybrid materials based on cellulose nanocrystals

We fabricated self-standing films of cellulose nanocrystals (CNC) and electrospun composite fibers with CNC and polyvinyl alcohol both with magnetic properties arising from cobalt iron oxide nanoparticles in the CNC matrix. Aqueous dispersions of cobalt-iron oxide nanoparticles (10–80 nm diameter) and CNCs (ca. 150 nm length) were used as precursor systems for the films and composite fibers. The properties of the hybrid material were determined by electron and atomic force microscopy, X-ray diffraction, thermogravimetry and magnetometry. The CNC-inorganic system was ferromagnetic, with a saturation magnetization of ca. 20 emu g^?1 of the magnetic phase. We demonstrate potential applications of the precursor dispersions, including magnetic fluid hyperthermia and highlight possible uses of the CNC-based magneto-responsive systems in biomedical and magneto-optical components.