Bio-based epoxidized natural rubber/chitosan/cellulose nanocrystal composites for enhancing mechanical properties,self-healing behavior and triboelectric nanogenerator performance

Cellulose - A new biocomposite was prepared from epoxidized natural rubber (ENR) reinforced with chitosan (CHI) and cellulose nanocrystals (CNCs) without using conventional crosslinking agents. The...     

Microfibrillated cellulose/cellulose acetate composites: Effect of surface treatment

Microfibrillated cellulose (MFC), which consists of a web‐like array of cellulose fibrils having a diameter in the range of 10–100 nm, was incorporated into a cellulose acetate (CA) matrix to form a totally biobased structural composite. Untreated and a 3‐aminopropyltriethoxysilane (APS) surface treated MFC was combined with a CA matrix by film casting from an acetone suspension. The effectiveness of the surface treatment was determined by infrared spectroscopy and X‐ray photoelectron spectroscopy. The Young's moduli of APS treated MFC composite films increase with increasing MFC content from 1.9 GPa for the CA to 4.1 GPa at 7.5 wt % of MFC, which is more than doubled. The tensile strength of the composite film increases to a maximum of 63.5 MPa at 2.5 wt % compared to the CA which has a value of 38 MPa. The thermal stability of composites with treated MFC is also better than the untreated MFC. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 153–161, 2010     

Structure and properties of regenerated cellulose/tourmaline nanocrystal composite films

Nanocomposite films were successfully prepared from cellulose and tourmaline nanocrystals with mean diameters of 70 nm in a 1.5 M NaOH/0.65 M thiourea aqueous solution by coagulation with 5 wt % CaCl₂ and then a 3 wt % HCl aqueous solution for 2 min. The structure and properties of the composite films were characterized by X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and tensile testing. The results indicated that the tourmaline nanocrystals were dispersed in a cellulose matrix, maintaining the original structure of the nanocrystals in the composite films. The loss peaks (tan δ) in the DMA spectra and the decomposition temperatures in the DSC curves of the composite films were significantly shifted toward low temperatures, suggesting that the nanocrystals broke the partial intermolecular hydrogen bonds of cellulose, and this led to a reduction in the thermal stability. However, the nanocomposite films exhibited a homogeneous structure and dispersion of the nanocrystals. When the tourmaline content was in the range of 4–8 wt %, the composite films possessed good tensile strength (92–107 MPa) and exhibited obvious antibacterial action against Staphylococcus aureus. This work provides a potential way of preparing functional composite films or fibers from cellulose and nanoinorganic particles with NaOH/thiourea aqueous solutions. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 367–373, 2004     

New PP/PLA/cellulose composites: effect of cellulose functionalization on accelerated weathering behavior (accelerated weathering behavior of new PP/PLA/cellulose composites)

Polylactic acid (PLA) was used as partial replacement for conventional thermoplastic matrix, new composites comprising cellulose, polypropylene (PP), and PLA being realized. In order to obtain a compatible interface between cellulosic pulp and polymeric matrix, two chemical modifications of cellulose with stearoyl chloride and toluene di‐isocyanate (TDI) were performed, structural changes being evidenced by X‐ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The composite materials were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, dynamic scanning calorimetry, impact, tensile and melt rheological tests, surface tension, and dynamic vapor sorption. Because promising results for impact strength and Young modulus were recorded when replacing 15% of PP with PLA in blends of PP with the same cellulosic pulp load, the aim of our study was to assess the behavior to accelerate weathering of composites comprising PP, cellulosic pulp, and PLA. Although the slight decrease in the mechanical properties was recorded after accelerated weathering, the use of functionalized cellulose successfully prevented the deterioration of surface materials, especially for composite comprising stearoyl chloride treated cellulose pulp. Copyright © 2015 John Wiley & Sons, Ltd.     

纳米羟基磷灰石/胶原复合材料制备方法比较研究

低温下,通过将水热合成的纳米羟基磷灰石浆料与中性胶原溶胶共混和在中性胶原中原位形成羟基磷灰石两种方法制备羟基磷灰石／胶原复合材料,采用XRD、FTIR、扫描电镜、透射电镜和力学性能测试等方法对两种复合材料的特性进行了表征。通过对两种方法制备的复合材料的特性进行比较,发现两种方法均制备得到了纳米羟基磷灰石／胶原复合材料,复合材料在晶相组成、化学组成、纳米羟基磷灰石晶体尺寸、胶原纤维的结构等方面都与天然骨相似。但原位合成纳米羟基磷灰石晶体的结晶度比水热合成的纳米羟基磷灰石更接近于自然骨,原位合成的羟基磷灰石／胶原复合材料的均匀性、界面结合紧密度、力学性能等方面均优于共混法。原位合成法是改善纳米羟基磷灰石／胶原复合材料均匀性和力学性能的有效方法。     

Electronic states and luminescence in higher fullerene/porous Si nanocrystal composites

Photoluminescence (PL) measurements have been performed on the nanocomposites of higher fullerene-coupled porous silicon (PS) nanocrystals. For the C70PS and C76(78)PS nanocomposites, the PL spectra show a pinning wavelength at approximately 565 nm and for the C84PS and C94PS nanosystems the pinning wavelength is at approximately 590 nm. The PL pinning property is closely related to the sorts of the coupled fullerenes. A band mixing model of direct and indirect gaps in a nanometer environment consisting of nc-Si core, SiO2 surface layer, and coupled fullerene has been proposed for calculation of electronic states. Good agreement is achieved between the experiments and theory.     

Isothermal melt and cold crystallization kinetics of poly(aryl ether ketone ether ketone ketone)

The isothermal melt and cold crystallization kinetics of poly(aryl ether ketone ether ketone ketone) are investigated by differential scanning calorimetry over two temperature regions. The Avrami equation describes the primary stage of isothermal crystallization kinetics with the exponent n ≈ 2 for both melt and cold crystallization. With the Hoffman–Weeks method, the equilibrium melting point is estimated to be 406 °C. From the spherulitic growth equation proposed by Hoffman and Lauritzen, the nucleation parameter (K_g) of the isothermal melt and cold crystallization is estimated. In addition, the K_g value of the isothermal melt crystallization is compared to those of the other poly(aryl ether ketone)s. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1992–1997, 2000     

Impact of cellulose nanocrystal aspect ratio on crystallization and reinforcement of poly(butylene adipate‐co‐terephthalate)

Cellulose nanocrystals (CNCs) are appealing nanomaterials for the reinforcement of polymeric materials. It is now well established that high mechanical properties are obtained when preparing the nanocomposite by casting/evaporation methods and using CNC contents above the percolation threshold. This phenomenon results from the formation of a stiff CNC network within the matrix meaning that the properties of the matrix play only a limited role on the mechanical properties of the material when the matrix is in the rubbery state. In subpercolation concentration or when using a different processing technique, the level of understanding is less clear, mainly when the CNC‐induced crystallization of the matrix interferes with the reinforcing mechanism. In this study, we used CNCs with different aspect ratios to prepare nanocomposites by extrusion with polybutyrate adipate terephthalate as matrix. The impact of CNC on the crystallinity of the matrix and mechanical properties of the nanocomposite has been investigated. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2284–2297     

Preparation and characterization of cellulose acetate/polysiloxane composites

Composites of cellulose acetate and polysiloxane were prepared using 3-isocyanatepropyltriethoxysilane, as a coupling agent. The structure, the thermal and dynamic-mechanical behaviors, and the morphology of the obtained composites were investigated. The composites showed phase separation which was confirmed by the presence of siloxane micro- and nano-domains dispersed in the cellulose acetate matrix, with good interfacial adhesion between the phases. The results demonstrated that the incorporation of a polysiloxane phase on a cellulose acetate matrix caused a decrease in the glass transition temperature, storage modulus and hardness. The proposed methodology was seen to be convenient for the preparation of cellulose acetate/polysiloxane composites with useful properties.     

A comparative study on the thermomechanical and electrical properties of carbide/or graphite/epoxy-reinforced composites

Journal of Thermal Analysis and Calorimetry - Three series of epoxy composite systems were fabricated and tested varying the filler type and content. An epoxy resin was employed as the matrix,...     

Thermal analysis and crystallinity study of cellulose nanofibril-filled polypropylene composites

The isothermal and non-isothermal decompositions of cellulose nanofiber (CNF) and microfibrillated cellulose (MFC)-filled polypropylene (PP) composites were evaluated and compared with microcrystalline cellulose (MCC)-filled composites by means of thermogravimetric analysis (TG). X-ray diffraction was employed to evaluate crystallinity of the composites. The degree of maximum thermal degradation (ultimate DTG peak value) increased and thermal degradation onset temperature decreased as the cellulose content increased because the thermal stability of cellulose fillers is lower than that of neat PP, but the thermal degradation of the composite was hindered at higher temperature conditions because of the increased residual mass content of the cellulose nanofibril fillers compared to the matrix polymer. The isothermal residual mass of the cellulose nanofibril-filled PP composites under melt blending and injection molding temperatures was decreased marginally by incorporation of the cellulose reinforcement but still exhibited considerable isothermal stability. The raw materials and composites examined in this study were not affected by the manufacturing process temperatures utilized to produce the composites. The MCC decreased the composite crystallinity while the nano-sized cellulose (CNF and MFC) did not appear to have an effect on crystallinity.     

Size-dependent phase stability of a molecular nanocrystal: a proxy for investigating the early stages of crystallization

We make the link between the size-dependent phase stability of a nanocrystal and the phase-transition behavior of emerging crystallites during the earliest stages of crystallization, by using the former as a proxy for the latter. We outline an extension of the classical nucleation theory to describe crystal nucleation and subsequent transformations of competing polymorphic phases that characterize Ostwald's rule of stages. The theoretical framework reveals that the relative stability of the competing phases is a function of cluster size, which in turn varies with time, and therefore explains the complex transformation behavior observed for some systems. We investigated the stability of a nanocrystal of dl-norleucine by means of molecular simulation as a proxy for post-nucleation phase-transformation behavior in emerging crystallites. The simulations reveal that, for nanocrystals, the surface energy of the transition state of a transformation can dominate the barrier to phase change, thus causing metastable phases to be stabilized, not because they are thermodynamically stable, but rather due to kinetic hindering. Therefore, in the context of the earliest stages of crystal growth, not only does phase stability vary as a function of cluster size, and hence time, but thermodynamically feasible transformations are also prone to kinetic hindering.     

Rheological properties of cellulose nanocrystal-embedded polymer composites: a review

Nanotechnology provides useful insights into the behavioural properties of materials from the nanoscale point of view, enabling researchers to develop new materials that were previously inconceivable. Cellulose is an ideal candidate for nanomaterial for nanotechnology because of its nanofibrillar structure, abundance, renewability, biodegradability and eco-friendly nature. Nanocrystalline cellulose materials have become the focus many studies related to these materials and their applications. This review summarises the current knowledge on the field of nanomaterials, focussing mainly on the rheological behaviour of polymer nanocomposites embedded with nanocrystalline cellulose. This review will enable better understanding of the use of nanocrystalline cellulose for the development and applications of cellulose nanocrystal-based nanocomposites.     

Morphology and thermal stability of bacterial cellulose/collagen composites

The aim of this paper was to prepare composites of bacterial cellulose (BC) and collagen to evaluate both the effect of collagen on the morphological, mechanical and thermal properties of BC and the effect of BC on the thermal stability of collagen for designing composites with increased potential biomedical applications. Two series of composites were prepared, the first series by immersing BC pellicle in solutions of collagen obtained in three forms, collagen gel (CG), collagen solution (CS) and hydrolysed collagen (HC), followed by freeze drying; and the second series of composites by mixing BC powder in solutions of collagen (CG, CS and HC), also followed by freeze drying. The properties of obtained composites were evaluated by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), mechanical tests, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The results revealed that BC acts as a thermal stabilizer for CS matrix, while with CG matrix it interacts synergistically leading to composites with improved properties. On the other hand, the BC sheet impregnated with collagen has a significantly improved thermal stability. Collagen (as HC, CS or CG) has also a positive influence on the mechanical properties of lyophilized BC sheet. A four times increase of modulus was observed in BC/HC and BC/CG composites. and an increase of 60 times for BC/CS. The spectacular increase of elastic modulus and tensile strength in the case of BC/CS composite was explained by the easier penetration of collagen solution in the BC network and impregnation of BC fibrils as revealed by SEM and AFM analyzes.

Open image in new window

     

Effects of melt processing conditions on photo-oxidation of PP/PPgMA/OMMT composites

This article reports the studies of photo-oxidative behaviour of polypropylene/maleic anhydride-grafted polypropylene/organic modified montmorillonite (PP/PPgMA/OMMT) composites prepared by two different melt processing methods. Samples of pristine polypropylene (PP) and PP/PPgMA/OMMT composites were prepared in an internal mixer and in a twin screw extruder. The samples were exposed to long wavelength radiations (λ > 300 nm) for the photo-oxidation. The samples were examined by FTIR, X-ray diffraction and microscopy. Similar to the pristine (PP), it is found that the photo-oxidation process in the composites depends on the melt processing conditions, which could cause the deterioration of organic modifier of the clay and the polymer matrix. The new radicals formed in addition to the iron impurities in the montmorillonite accelerate the photo-oxidation.     

Aerogel nanoarchitectonics based on cellulose nanocrystals and nanofibers from eucalyptus pulp: preparation and comparative study

Cellulose - Nanocellulose-based materials have attracted significant attention because of their attractive advantages. Particularly, aerogel, a porous nanocellulose material, have been used in...     

Ionic strength effects on the microstructure and shear rheology of cellulose nanocrystal suspensions

The effect of ionic strength on the rheology and microstructure of Cellulose nanocrystals (CNC) aqueous suspensions are studied over a broad range of CNC (3–15 wt%) and NaCl concentrations (0–15 mM), using polarized optical microscopy combined with rheometry. The CNC suspensions are isotropic at low concentration and form chiral nematic liquid crystalline structure above a first critical concentration and gel above a second critical one. It has been shown that for isotropic CNC suspensions, increasing the ionic strength of the system up to 5 mM NaCl concentration weakens the electro-viscous effects and thus reduces the viscosity of these suspensions. For biphasic samples, which contain chiral nematic liquid crystal domains, increasing the ionic strength up to 5 mM NaCl concentration decreases the size of the chiral nematic domains, and leads the viscosity of the samples at low shear rates to increase. On the other hand, at high shear rates, where all the ordered domains are broken, the viscosity decreases with NaCl addition. For gels, the addition of NaCl up to 5 mM weakens the gel structure and decreases the viscosity. Further addition of NaCl (10 and 15 mM NaCl concentrations) results in extensive aggregation and de-stabilizes the CNC suspensions.     

Nonisothermal cold crystallization behavior and kinetics of polylactide/clay nanocomposites

The nonisothermal cold crystallization behavior of intercalated polylactide (PLA)/clay nanocomposites (PLACNs) was studied using differential scanning calorimetry, polarized optical microscope, X‐ray diffractometer, dynamic mechanical thermal analysis, and Fourier transform infrared spectrometer. The results show that both the cold crystallization temperature (T_cc) and melting point (T_m) of PLA matrix decreases monotonously with increasing of clay loadings, accompanied by the decreasing degree of crystallinity (X_c%) at the low heating rates (≤5 °C/min). However, the X_c% of PLACNs presents a remarkable increase at the high heating rate of 10 °C/min in contrast to that of neat PLA. The crystallization kinetics was then analyzed by the Avrami, Jezioney, Ozawa, Mo, Kissinger and Lauritzen–Hoffman kinetic models. It can be concluded that at the low heating rate, the cold crystallization of both the neat PLA and nanocomposites proceeds by regime III kinetics. The nucleation effect of clay promote the crystallization to some extent, while the impeding effect of clay results in the decrease of crystallization rate with increasing of clay loadings. At the high heating rate of 10 °C/min, crystallization proceeds mainly by regime II kinetics. Thus, the formation of much more incomplete crystals in the PLACNs with high clay loadings due to the dominant multiple nucleations mechanism in regime II, may have primary contribution to the lower crystallization kinetics, also as a result to the higher degree of crystallinity and lower melting point in contrast to that of neat PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1100–1113, 2007