质子导体BaCe0.8Lu0.2O3-α的电性能

采用高温固相法制备了BaCe_0.8Lu_0.2O_3-α质子导体。运用X射线衍射仪（XRD）、扫描电镜（SEM）对该材料的物相结构、微观形貌进行了表征。在500~900℃温度范围内,应用交流阻抗谱和气体浓差电池方法研究了材料在不同气体气氛中的离子导电性和氢-空气燃料电池性能。结果表明,BaCe_0.8Lu_0.2O_3-α材料为单一斜方晶结构,具有良好的致密性。在500~900℃温度范围内,干燥或湿润的氮气、空气和氧气中,材料的电导率随着氧分压增大稍有增大。在湿润的氢气中,材料表现为纯的质子导电性。在以该材料为固体电解质的氢-空气燃料电池条件下,材料表现为质子、氧离子和电子的混合导电性,其中离子导电性始终占主导;氢-空气燃料电池在900℃下的最大输出功率密度为92.2mW·cm^-2,高于我们以前报道的BaCe_0.8RE_0.2O_3-α（RE=Pr,Eu,Ho,Er,等）材料。     

中温固体氧化物燃料电池阴极Sr3Fe2-xNixO7-δ(x=0,0.1,0.2,0.3)的制备与性能

采用溶胶凝胶法(sol-gel)合成了Sr_3Fe_(2-x)Ni_xO_(7-δ)(x=0,0.1,0.2,0.3)系列阴极材料,通过X射线衍射、热膨胀系数测试、电导率测试、极化阻抗(R_p)测试、单电池性能测试等对材料的物相结构、热力学性能、电化学性能进行了表征。结果表明,所有样品均成功合成为具有类钙钛矿结构的单一纯相。热膨胀系数随着Ni元素掺杂含量的提高而不断下降。其高温电导率随着Ni元素掺杂含量的提高而升高,SFN30具有该系列最高的电导率101 S·cm~(-1)。该系列样品的极化阻抗随着Ni元素掺杂含量的提高呈现先下降后上升的趋势,SFN10在800℃具有小的极化阻抗(R_p=0.078 8Ω·cm~2)。电解质支撑的单电池输出功率变化趋势与极化阻抗趋势一致,SFN10在800℃获得421.6 mW·cm~(-2)的输出功率密度。     

CexPr1-xO2-δ复合氧化物的XRD和Raman表征

A series of Ce_xPr_1-xO_2-δ mixed oxides were synthesized by sol-gel method and characterized by Raman and XRD techniques. When x value was changed from 1.0 to 0.5, only a cubic phase CeO₂ was observed. The samples were very well crystallized on decreasing x from 0.50 to 0.99. For Ce_xPr_1-xO_2-δ samples 465 cm^-1 and 1 150 cm^-1 Raman peaks are attributed to the Raman active F_2g mode of CeO₂. The broad peak at about 570 cm^-1 in the region of 0.3 ≤x≤ 0.99 can be linked to lattice defects resulting in oxygen vacancies. The new band at about 195 cm^-1 may be attributed to the asymmetric vibration caused by the formation of oxygen vacancies. Calcination temperatures had great effect on the peak intensity for CeO₂ but less effect on Ce_0.8Pr_0.2O_2-δ in Raman spectra. It might be due to the transformation of the colors for the mixed oxides, the insertion of Pr atom into the ceria lattice could enhance the sintering resistance and thermal stability of the mixed oxides.     

BaCe_(0.8-x)Nb_xGd_(0.2)O_(3-δ)(0≤x≤0.45)的制备及性能研究

采用高温固相反应法制备了质子导体BaCe0.8-xNbxGd0.2O3-δ(0≤x≤0.45)。结合XRD、SEM、EIS等技术对其物相、微观形貌、稳定性及电导率进行了研究。结果表明,在1600℃烧结5h制备的质子导体BaCe0.8-xNbxGd0.2O3-δ(0≤x≤0.45)均能保持主相为斜方晶的钙钛矿结构。Nb的加入可明显提高烧结样品的致密性及在CO2和水蒸气气氛下的稳定性。在湿润H2/Ar(0.4%,V/V)气氛中800℃下,x=0.1样品的电导率为5.73mS·cm-1,电导活化能为0.35eV,与x=0的样品相当。     

BaxCe0.8Y0.2O3-α固体电解质的氧离子导电性

Ba_xCe_0.8Y_0.2O_3-α(x=1.03，1，0.98) solid electrolyte samples show a single phase of orthorhombic perovskite of BaCeO₃. The oxide-ion conduction and transport number were detected in the temperature of 600～1000℃ by electrochemical oxygen permeation (oxygen pumping)， and compared with the results from the oxygen concentration cell. The relation between the ingredient of Ba and oxide-ion conduction was also researched. It was found that these electrolytes exhibited the mixed oxide-ionic and electronic hole conduction under the experimental temperature and oxygen gas. The oxide-ion transport numbers are 0.1～0.6， which are close to the results of the oxygen con-centration cell. They increase as the decrease of Ba content in the samples.     

纳米Ce1-xLaxO2-δ的微波引诱燃烧合成及其性能表征

Nanometer Ce_1-xLa_xO_2-δ solid solutions were synthesized by microwave-induced combustion process us-ing cerium nitrate hexahydrate， lanthanum nitrate hexahydrate and urea as raw materials. The process took only six minutes to obtain La₂O₃-doped CeO₂ nanopowders. The nanopowders were characterized by XRD， Laser Raman spectrum ， UV-Vis spectroscopy，field-emission scanning electron micrograph(FE-SEM)and TEM. The results revealed that the grain size of Ce_1-xLa_xO_2-δ varied from 20 to 40 nm calculated by Scherer formula through the plane of (111)， that oxygen vacancy was produced in the crystal lattices and the concentration of oxygen vacancy was increased with La doping， therefore the covalence of Ce-O bond was strenthened， which results in more intensive UV-C(200～280 nm)absorption. It can be seen from SEM that the porous appearance was obtained. Grain size is no more than 40nm observed from TEM.     

固体电解质La2-xCaxMo1.7W0.3O9-δ(0≤x≤0.2)的合成、表征及电性能

在氧离子导体La₂Mo_1.7W_0.3O₉的基础上，采用固相法合成了La位掺杂的Ca系列新型氧化物La_2-xCa_xMo_1.7W_0.3O_9-δ(0≤x≤0.2)。通过XRD、Raman和XPS等手段对化合物结构进行表征，交流阻抗谱测试其电性能。结果表明：掺杂离子Ca²⁺的半径小于基质离子La³⁺的半径导致晶格收缩；Ca的掺杂在La₂Mo_1.7W_0.3O₉自身内置氧空位的基础上增加了额外的氧空位，提高了氧离子导体的电导率，550 ℃电导率由0.79 × 10^-4 S·cm^-1 (x=0.0)增加到1.5 × 10^-4 S·cm^-1 (x=0.16，0.2)，电导率增加89.9%。     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

La1-xCaxFeO3-δ系阴极材料的GNP法合成及电性能研究

采用甘氨酸-硝酸盐(GNP)法合成了LaFeO₃及La_1-xCa_xFeO_3-δ(x=0.1～0.5)系列粉体，用TG-DTA、XRD、TEM、SEM等对产物形成过程及微结构进行了表征。结果表明，所合成的系列样品均形成钙钛矿结构的单相固溶体。在x≤20mol%的Ca含量范围内，产物为正交钙钛矿结构；当x>30mol%时，转变为立方钙钛矿相。相同条件下产物的衍射峰强度、晶胞体积及晶粒尺寸都随Ca含量的增大而减小。采用直流四端子法测量了烧结体在中温(450～800 ℃)区的电导率。掺杂使样品导电能力显著增强，电导率随Ca²⁺掺入量的增大先增大后减小，La_0.6Ca_0.4FeO_3-δ样品的电导率最高。在低温段，各样品的导电行为符合小极化子导电机制，导电活化能为13.67～22.70 kJ·mol^-1。     

Tb2O3掺杂的BaCeO3的混合导电性

制备了Ba_xCe_0.8Tb_0.2O_3-α（x=0.98~1.03）系列固体电解质，用X-射线衍射法对其结构进行了表征，用交流阻抗谱方法和气体浓差电池方法测定了样品在500~1000℃温度范围、不同气氛中的导电特性，讨论了非化学计量组成（x≠1）对样品导电性能的影响并与化学计量组成（x=1）样品进行了比较。结果表明，这三个样品均为钙钛矿型斜方晶结构。在500~1000℃下，在干燥和潮湿的氧气、空气和氮气气氛中，样品以电子空穴导电为主；在潮湿的氢气气氛中，以质子导电为主，其电导率比不含氢气气氛（O₂，air，N₂）中的电导率约高两个数量级。同一样品在潮湿气氛中的电导率稍高于相应的干燥气氛中的电导率；非化学计量组成样品的电导率高于化学计量组成样品的电导率。     

纳米微孔NixZn(1-x)Fe2O4的水热合成研究

０引言尖晶石型铁酸盐是一类重要的磁性材料，它可用于防止电磁波辐射设备以及隐身材料中的吸波剂犤１，２犦，具有价格低廉、吸波性能优良的特点。同时尖晶石型铁酸盐也是一类重要的催化剂，９０年代初又发现了氧缺位的该类化合物具有将CO２还原为C的优良催化性能犤３犦。因此，有关铁酸盐的制备及性能研究一直是化学工作者和材料科学工作者感兴趣的领域。随着新的合成方法的不断涌现，对传统铁氧体材料进行结构改造以提高其性能是一个重要的研究发展方向，本文采用模板剂造孔技术，首次在NixZn（１－x）Fe２O４水热合成中选用模板剂，…     

xLi2MnO3-(1-x)LiNi0.7Co0.3O2的低温燃烧合成及电化学性能研究

采用低温燃烧法合成了锂离子电池正极材料xLi₂MnO₃-(1-x)LiNi_0.7Co_0.3O₂,对合成产物的结构、形貌和电化学性能进行了系统的研究, 通过单因素试验对合成条件和材料的组成进行了优化。结果表明:采用低温燃烧法合成的富锂层状正极材料具有α-NaFeO₂型层状结构、球状形貌和良好的电化学性能;其最佳合成条件为:回火温度850℃, 回火时间20 h;Li₂MnO₃的最佳配比为x=0.7.在此条件下合成的0.7Li₂MnO₃-0.3LiNi_0.7Co_0.3O₂,最高放电比容量达到263.1 mAh·g^-1,并具有良好的循环性能和倍率性能。     

锂离子电池正极材料LiNi0.75-xCoxMn0.25O2的合成及电化学性能研究

以LiOH·H₂O、Ni(OAc)₂·4H₂O、Co(OAc)₂·4H₂O和MnO₂为原料，在水热反应釜中预处理，然后进行高温固相反应，合成了一系列锂镍钴锰氧化物LiNi_0.75-xCo_xMn_0.25O₂(x=0.05,0.10,0.15,0.20,0.25)。通过X射线衍射(XRD)、扫描电子显微镜（SEM）和电化学性能测试对所得样品的结构、形貌、粒径及电化学性能进行了表征。结果表明，当x=0.20时，所合成的正极材料具有很好的α-NaFeO₂型层状晶体结构，晶胞参数a=0.286 1 nm，c=1.416 4 nm， V=0.100 4 nm³，以50 mA·g^-1的电流密度在3～4.3 V(vs Li/Li⁺)充放电时，首次放电比容量达172.5 mAh·g^-1，首次放电效率高达90.9%，30个循环后其放电比容量依然保持在161.1 mAh·g^-1。     

La1-xSrxCoO3（x=0，0.2，0.4，0.6，0.8）钙钛矿型氧化物的催化性能及改性

通过溶胶-凝胶法制备出A位Sr掺杂的钙钛矿型氧化物La_1-xSr_xCoO₃（x=0,0.2,0.4,0.6,0.8）,并将其作为催化剂应用于双功能氧电极中。测试结果表明,A位Sr的掺杂的La_1-xSr_xCoO₃比LaCoO₃具有更高的电催化活性,并且La_0.6Sr_0.4CoO₃在氧还原和氧析出反应中均表现出最优的催化性能,最大电流密度分别达到0.244 A·cm^-2（-0.6 V vs Hg/HgO）和0.303 A·cm^-2（1 V vs Hg/HgO）。为进一步提高催化剂的催化活性,将水热法制备的α-MnO₂纳米管与La_0.6Sr_0.4CoO₃复合作为双功能催化剂。当α-MnO₂的质量分数为40%时,比起单一的α-MnO₂或钙钛矿氧化物,α-MnO₂/La_0.6Sr_0.4CoO₃复合材料表现出协同效应,有更好的双功能电催化活性,使双效氧电极具有更好的电化学性能及稳定性。     

La1-xCaxMnO3纳米颗粒的制备及氧还原催化性能

本文采用溶胶凝胶法制备了一系列不同Ca含量的钙钛矿型氧化物La_1-xCa_xMnO₃(x=0~0.4)纳米颗粒, X射线粉末衍射及精修、扫描电镜表征显示其相纯度和结晶度高, 颗粒平均粒径约40 nm。在0.1 mol·L^-1 KOH水溶液中进行的氧还原电催化性能测试显示, La_0.7Ca_0.3MnO₃样品催化活性最高, 表观电子转移数接近4, 还原电流密度与Pt/C催化剂相当, 而催化稳定性优于Pt/C。进一步研究了La_1-xCa_xMnO₃样品中Mn价态、晶胞参数的改变对氧还原催化活性的影响, 结果表明当x=0.3时, 催化剂中Mn处于混合价态, Mn-O键长适中, 最有利于电催化反应。     

锶掺杂对La1-xSrxNbO4-σ质子导体性能的影响

利用高温固相反应法制备了Sr掺杂LaNbO₄质子导体La_1-xSr_xNbO_4-σ(0≤x≤0.02),并且对其性能进行了表征。XRD分析表明,所有的样品具有单斜结构,晶胞体积随Sr掺杂量的增加而增大;La_1-xSr_xNbO_4-σ样品在沸水中和二氧化碳气氛中具有很好的化学稳定性。SEM分析表明,La_1-xSr_xNbO_4-σ粉体经1500℃烧结8h后均得到致密的、晶粒均匀的样品;Sr的掺杂抑制了陶瓷体裂缝的产生和晶粒的过度增长;随Sr的掺杂量增加,晶粒变小。交流阻抗谱分析表明,Sr掺杂改变了LaNbO₄的电导率,其中样品La_0.995Sr_0.005NbO_4-σ具有最高的电导率;样品在25℃水汽饱和的5%H₂-Ar气氛下的电导率明显高于干燥空气气氛,在800℃时,La_0.995Sr_0.005NbO_4-σ电导率达到0.003S·cm^-1,电导活化能为0.44eV。     

NbS2-xSex的制备、表征及其摩擦学性能

本文采用固相反应合成了NbS_2-xSe_x纳米材料。并分别采用XRD、SEM、TEM、HRTEM进行了结构、形貌和成分的分析表征。系统研究了合成温度、保温时间及不同掺杂量对产物晶型和形貌演化的影响及规律性。结果表明Se的掺杂使NbS_2-xSe_x的形貌由纳米带(板)转变为纳米片,衍射峰明显宽化,峰强变弱,晶粒细化。且掺杂量、保温温度及时间对产物的形貌影响较大;在750℃下保温2h得到的掺杂5at%Se的NbS_1.9Se_0.1形貌良好。将NbS_2-xSe_x作为液体石蜡油的添加剂的UMT-2摩擦学实验结果表明掺杂后的NbS_2-xSe_x具有优异的摩擦性能,其中掺杂5at%的Se在750℃下保温2h的NbS_1.9Se_0.1摩擦性能最佳,同时对其摩擦机理进行了解释。     

阴极材料LaFe0.8-xCuxNi0.2O3的合成和烧结性能

LaFe_0.8-xCu_xNi_0.2O₃ (x=0.0~0.2) (LFCN), a new cathode material of solid oxide fuel cell (SOFC), was synthesized by Co-precipitation method using sodium bicarbonate. The lattice structures of samples with different x contents were characterized by XRD. Porosity and density of the porous LaFe_0.8-xCu_xNi_0.2O₃ (x=0.0~0.1) as a function of sintering temperature were investigated. It was found that the orthorhombic structure could be formed after calcination at 900 ℃ for 4 h. The particle size of LFCN was about 350 nm. The density of the porous LFCN increased with sintering temperature, but the opposite was true for the porosity. On the other hand, at the same sintering temperature, the porosity of LaFe_0.8-xCu_xNi_0.2O₃ (x=0.0~0.1) decreased with increasing x contents. It is indicated that the dopant of Cu on LaFe_0.8Ni_0.2O₃ can facilitate the sintering of the materials. After sintering at 1 100 ℃ for 4 h, the porous LaFe_0.7Cu_0.1Ni_0.2O₃ was still with appropriate structure, and its porosity was 29%.     

Ce0.8Sm0.2O1.9的尿素燃烧法合成与性能

采用以尿素为燃料的燃烧合成法制备Ce0.8Sm0.2O1.9(SDC)氧离子导体材料, 对燃烧合成粉体的物相和显微形态进行了表征, 并研究了燃烧法合成SDC的烧结性能以及烧结体的导电性能. 研究结果表明, 采用尿素燃烧法合成SDC具有简便高效和合成粉体烧结活性高的优点. 经过燃烧过程后即可得到立方萤石结构的纯相SDC粉体, 合成粉体的分散性良好, 为50~150 nm的球形颗粒, 具有高的烧结活性, 在1250 ℃的烧结温度下, 陶瓷样品的相对密度可达到95.1%. 在600和800 ℃的测试温度下, 烧结温度为1250 ℃的陶瓷样品的电导率分别达到5.4×10-2和1.0×10-1 Ω-1·cm-1.