Highly Conductive PEDOT:PSS Films with 1,3‐Dimethyl‐2‐Imidazolidinone as Transparent Electrodes for Organic Light‐Emitting Diodes

Highly conductive poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films as transparent electrodes for organic light‐emitting diodes (OLEDs) are doped with a new solvent 1,3‐dimethyl‐2‐imidazolidinone (DMI) and are optimized using solvent post‐treatment. The DMI doped PEDOT:PSS films show significantly enhanced conductivities up to 812.1 S cm⁻¹. The sheet resistance of the PEDOT:PSS films doped with DMI is further reduced by various solvent post‐treatment. The effect of solvent post‐treatment on DMI doped PEDOT:PSS films is investigated and is shown to reduce insulating PSS in the conductive films. The solvent posttreated PEDOT:PSS films are successfully employed as transparent electrodes in white OLEDs. It is shown that the efficiency of OLEDs with the optimized DMI doped PEDOT:PSS films is higher than that of reference OLEDs doped with a conventional solvent (ethylene glycol). The results present that the optimized PEDOT:PSS films with the new solvent of DMI can be a promising transparent electrode for low‐cost, efficient ITO‐free white OLEDs.

     

Coulometric Response of H+-Selective Solid-Contact Ion-Selective Electrodes and Its Application in Flexible Sensors†

The analytical performance of H⁺-selective solid-contact ion-selective electrodes (SCISEs) based on solid contact polyaniline doped with chloride (PANI(Cl)) and poly(3,4-ethylenedioxythiophene) doped with poly(styrene sulfonate) (PEDOT(PSS)) was characterized by a developed coulometric signal transduction method. PEDOT(PSS) solid contact is covered by PVC based H⁺-selective membrane. The obtained coulometric signal demonstrates that the cumulated charge can be amplified by increasing the capacitance of solid contact. SCISEs covered with spin-coated membrane behave faster amperometric response than electrodes with drop-cast membrane. In contrast to earlier works, the amperometric response and impedance spectrum demonstrates H⁺ transfer through SCISEs is independent from the thickness of membrane. The exceptional behavior of PANI(Cl) H⁺-SCISEs shows that the capacitance estimated from impedance spectrum at low frequency 10 mHz and coulometric signal of PANI(Cl) based SCISEs is influenced by the applied potentials, whereas PEDOT(PSS) solid contact is independent from the chosen applied potentials. Furthermore, preliminary investigations of coulometric signal transduction on flexible pH sensor implies its potential applications in wearable sensors for sweat ion concentration detection.      

Highly Selective All‐Plastic,Disposable, Cu2+‐Selective Electrodes

Conducting polymers (CP) remain a promising material to construct stable potential all‐solid‐state ion‐selective potentiometric electrodes. The unique properties of poly(3,4‐ethylenedioxythiophene) doped with poly(4‐styrenesulfonate) ions, PEDOT‐PSS: high CP stability and affinity of doping anions towards Cu²⁺ ions, make it highly attractive for construction of all‐solid‐state copper(II)‐selective electrodes with outstanding selectivity. The additional benefits can arise from solution processability of commercially available PEDOT‐PSS system. This material was highly promising for a new sensor arrangement, i.e. to obtain disposable, planar and flexible all‐plastic Cu²⁺‐selective electrodes. These sensors can be obtained by casting a commercially available dispersion of PEDOT‐PSS (Baytron P) on a plastic, non‐conducting support material. The CP being both electrical lead and ion‐to‐electron transducer, was covered with plastic, solvent polymeric Cu²⁺ selective membrane. This extremely simple arrangement, after conditioning in dilute Cu²⁺ solution, was characterized with linear Nernstian responses within the activities range from: 0.1 to 10^?4 M, followed by super‐Nernstian responses for lower activities. The latter result points to effective elimination of primary ions leakage from the plastic membrane / transducer phase and has resulted in significantly improved selectivities. Obtained log K values were equal to ?7.6 for Co²⁺, ?7.4 for Zn²⁺, ?7.2 for Ca²⁺ and ?6.8 for Na⁺, respectively.     

Metallic and non-metallic redox response of conducting polymers

The potentiometric response of electrodes coated with polypyrrole or poly(N-methylpyrrole) films with different doping anions was studied in solutions containing the redox couples: Fe(CN)₆^3−/4−, Ru(NH₃)₆^3+/2+ and Fe(Ill)/Fe(II). The stable potential measured with the electrodes was the potential of the redox couple. The response time was instant for polypyrrole doped with dodecylsulphate ions, PPy(DS) and slow for the polymers doped with mobile anions. On the basis of electrochemical measurements and chemical analysis by EDAX spectroscopy it was found that with the PPy(DS) electrode the potentiometric response was of the ‘metallic’ type, with no change in the oxidation state of the bulk polymer. With the other polymer systems studied reduction or oxidation of the polymer bulk took place when it was in contact with a redox couple in the solution.     

Counter-Ion Influence on Polypyrrole Potentiometric pH Sensitivity

The pH sensitivity of conducting polymer films is an important issue from the sensor design point of view. The doping and supporting electrolyte anions effect on the potentiometric sensitivity and response time of polypyrrole (PPy) electrodes towards changes of solution pH were studied. It was found that (i) the response of PPy doped by easily exchangeable common anions (Cl^–, NO₃ ^–, ClO₄ ^–) in their solutions (KCl, KNO₃, NaClO₄) is slow. In contrast, (ii) polypyrrole films deposited in the presence of weak acid anions (phthalates, oxalates, salicylates) were characterised by instantaneous responses in the above mentioned solutions. On the basis of electrochemical experiments (open circuit potential vs. time dependencies, cyclic voltammetry, EQCM), the observed differences were attributed to different mechanisms of pH sensitivity of tested films. The long response times are related to the incorporation of the solution ions into the film in order to compensate charges created due to protonation. On the other hand, if the ion-exchange is hindered as in the case of (ii), instantaneous open circuit responses are observed due to polarisation of the oxidised polymer layer, analogously to the metal electrode. Moreover, for these films the internal pH buffering within the polymer membrane will weaken the pH change effect.The mechanisms were confirmed in the course of studying the pH effect in solutions containing anions easily (KCl, NaClO₄, KNO₃) or hardly exchangeable with polypyrrole (K₂SO₄, sodium poly(4-styrenesulphonate) solutions) acidified with H₂SO₄.     

Electrochemical synthesis and characterization of poly(3,4-ethylenedioxythiophene) in ionic liquids with bulky organic anions

The electrochemistry of poly(3,4-ethylenedioxythiophene) (PEDOT) was studied in two ionic liquids with bulky organic anions, i.e., 1-butyl-3-methylimidazolium (BMIM) diethylene glycol monomethyl ether sulfate (MDEGSO₄) and BMIM octyl sulfate (OctSO₄). BMIM-MDEGSO₄ is a liquid, while BMIM-OctSO₄ is in solid form at room temperature. Electrosynthesis of PEDOT in BMIM-MDEGSO₄ with an EDOT concentration of 0.1 M and in BMIM-MDEGSO₄/EDOT 1/1 (w/w) solution resulted in no polymer at all or a very limited amount of polymer on the electrode surface, as determined by cyclic voltammetry in 0.1 M KCl(aq) solution. In contrast, electrosynthesis of PEDOT in BMIM-OctSO₄/EDOT 1/1 (w/w) resulted in a high yield of electroactive material on the electrode surface. Furthermore, electrosynthesis of PEDOT in ionic liquid–water solution (C_{ionic liquid}=1.5 M) containing 0.1 M EDOT was also found to give a relatively high yield of electroactive material on the electrode surface, both for 1.5 M BMIM-MDEGSO₄(aq) and 1.5 M BMIM-OctSO₄(aq). The PEDOT electrodes showed an anionic potentiometric response in 10^–5–10^–1 M KCl(aq) solution, indicating a predominant anion transfer at the polymer–solution interface despite the relatively bulky anions (MDEGSO₄^– or OctSO₄^–) incorporated as counterions in PEDOT during electropolymerization. On the basis of electrochemical impedance spectroscopy, the charge (ion) transport properties of the polymer film were strongly influenced by the water content of the ionic liquid (C_{ionic liquid}=0.05–2.0 M).Dedicated to Zbigniew Galus on the occasion of his 70th birthday     

Measurements of the capacitance and the response time of solid-state potentiometric sensors by an electrochemical time-of-flight method

A micro-electrochemical time-of-flight technique relying on galvanostatic ion generation and potentiometric sensing (P-ETOF) has been developed in order to characterize dynamic properties of solid-state potentiometric sensors and to measure their capacitance. Lithographically-fabricated generator-sensor devices featuring 10 m-wide micro-electrodes spaced by 20–50 m are used in either an open face mode, where hemi-cylindrical diffusion governs mass transport of generated ions, or in a narrow channel mode, where linear diffusion describes transport of ions between the generator and sensor micro-electrodes in a thin (~3 m) layer of electrolyte. P-ETOF-open face mode is capable of generating silver ions or protons at a rate equivalent to a current density of 10 A/cm². This induces a maximum, mass transport controlled rate of a sensor potential rise of ~80 V/s. P-ETOF was used to characterize anodically electrodeposited iridium oxide film pH micro-sensors. Their maximum rate of potential change was determined to depend inversely on the oxide films thickness and varied from 34 V/s for 40 nm-thick films to 9 V/s for the 650 nm-thick iridium oxide films. The capacitances of these pH micro-sensors were determined to depend linearly on their thicknesses, with a slope of 3 F cm^–2 nm^–1 and a specific capacitance of 30 F/cm³. These results point to slow proton transport in the bulk of the oxide film as a mechanistic element of their pH response.Dedicated to Zbigniew Galus on the occasion of his 70th birthday.     

Sol-Gel Processing and Luminescent Properties of Rare-Earth Oxyfluoride Materials

Luminescent rare-earth oxyfluoride materials were prepared by a sol-gel method using trifluoroacetic acid as a fluorine source. Crystalline (La, Eu)OF powders and thin films were obtained by heating gels at typically 600–800°C. Transparent SiO₂-LaOF glass-ceramic thin films were also prepared by mixing the trifluoroacetate sols and silica sols, spin-coating on silica glass substrates and heating at temperatures 600–900°C. Eu³⁺ ions doped in the oxyfluoride materials exhibited a strong red ⁵D₀ ⁷F₂ emission (611 nm) by a charge-transfer (O^2–-Eu³⁺) excitation with ultra-violet radiation (265 nm). It was strongly suggested that the Eu³⁺ activators were preferentially incorporated into the crystalline LaOF phase in the SiO₂-LaOF glass-ceramics.     

Electrochemical Behaviour of Poly(benzopyrene) Films Doped with Eriochrome Black T as a Pb2+‐Sensitive Sensors

Poly(benzopyrene) films were electrosynthesized on glassy carbon disk electrodes from benzo(a)pyrene by cyclic voltammetry in the presence of eriochrome black T, which forms strong complexes with lead ions. In consequence, by conditioning the films in high concentration of lead (0.1 mol dm^?3 Pb(NO₃)₂) potentiometric sensitivity to lead ions down to 10^?5 mol dm^?3 Pb²⁺ was induced, and a novel type of lead‐sensitive electrode was obtained. The electrode is characterized by high stability of the potential readouts, good reproducibility of the calibration curves as well as a minor hysteresis effects. The performance of our lead‐sensitive electrode was favourable compared to PEDOT and PPy‐based electrodes doped with eriochrome black T. We conclude that poly(benzopyrene) doped with eriochrome black T is a new electroactive material that may be applied in sensor technology.     

Potentiometric Ag+ Sensors Based on Conducting Polymers: A Comparison between Poly(3,4‐ethylenedioxythiophene) and Polypyrrole Doped with Sulfonated Calixarenes

Potentiometric Ag⁺ sensors were prepared by galvanostatic electropolymerization of 3,4‐ethylenedioxythiophene (EDOT) and pyrrole (Py) on glassy carbon electrodes by using sulfonated calixarenes as doping ions. Poly(3,4‐ethylenedioxythiophene) (PEDOT) and polypyrrole (PPy) doped with p‐sulfonic calix[4]arene (C4S), p‐sulfonic calix[6]arene (C6S) and p‐sulfonic calix[8]arene (C8S) were compared. PEDOT and PPy doped with poly(styrene sulfonate) (PSS) were also included for comparison. The analytical performance of the conducting polymer‐based Ag⁺ sensors was studied by potentiometric measurements. All conducting polymer and dopant combinations showed sensitivity and selectivity to Ag⁺ compared to several alkali, alkaline‐earth, and transition‐metal cations. The type of the conducting polymer used for the fabrication of the electrodes was found to have a more significant effect on the selectivity of the electrodes to Ag⁺ than the ring size of the sulfonated calixarenes used as dopants. Selected conducting polymer‐based sensors were studied by cyclic voltammetry (CV) and energy dispersive analysis of X‐rays (EDAX) measurements. Results from the EDAX measurements show that both PEDOT‐ and PPy‐based membranes accumulate silver.     

Influence of Anions on Electrochemical Properties of Polypyrrole-Modified Electrodes

The influence of anions ClO₄ ^–, NO₃ ^–, Cl^–, SO₄ ^2–, and DDS^– (dodecyl sulfate) on the cyclic voltammetric response of polypyrrole-modified electrodes is studied. The change in the film composition is examined by electron probe microanalysis. It is established that essential changes in the shape of voltammograms take place during cycling if the anions are not sufficiently freely mobile in the polymer film and insertion of cations from the solution is necessary to guarantee electroneutrality of the system. Some differences between the mobility of Cl^– ions and ClO₄ ^– or NO₃ ^– ions are in good agreement with the results of semi-empirical quantum chemical calculations showing that the interaction of Cl^– and Br^– ions with pyrrole oligomers is stronger than that of NO₃ ^– or ClO₄ ^– ions. Nevertheless, it is established that the peak current determined from voltammograms increases linearly with the increase of the scan rate with very high correlation coefficient. It means that it is possible to describe the behavior of ClO₄ ^–, NO₃ ^– and Cl^– ions in the framework of the model of free ions. The redox behavior of the PPy films doped with anions of low mobility such as SO₄ ^2– and DDS^– depends essentially on the nature of cations in the test solution. It is found that the mobility of cations increases in the row Li⁺ < Na⁺ < K⁺ < Cs⁺. The mobility of DDS^– ions in the PPy in ethanolic solution is significantly higher and their electrochemical properties are quite similar to PPy|Cl or NO₃ ^– film in aqueous solution.     

Novel lipoate-selective membrane sensor for the flow injection determination of alpha-lipoic acid in pharmaceutical preparations and urine

A potentiometric lipoate-selective sensor based on mercuric lipoate ion-pair as a membrane carrier is reported. The electrode was prepared by coating the membrane solution containing PVC, plasticizer, and carrier on the surface of graphite electrode. Influences of the membrane composition, pH, and possible interfering anions were investigated on the response properties of the electrode. The sensor exhibits significantly enhanced response toward lipoate ions over the concentration range 1 × 10⁻⁷ mol L⁻¹ to 1 × 10⁻² mol L⁻¹ with a lower detection limit of (LDL) of 9 × 10⁻⁸ mol L⁻¹ and a slope of −29.4 mV decade⁻¹, with S.D. of the slope is 0.214 mV. Fast and stable response, good reproducibility, long-term stability, applicability over a pH range of 8.0–9.5 is demonstrated. The sensor has a response time of ≤12 s and can be used for at least 6 weeks without any considerable divergence in its potential response. The proposed electrode shows good discrimination of lipoate from several inorganic and organic anions. The CGE was used in flow injection potentiometry (FIP) and resulted in well defined peaks for lipoate ions with stable baseline, excellent reproducibility and reasonable sampling rate of 30 injections per hour. The proposed sensor has been applied for the direct and FI potentiometric determination of LA in pharmaceutical preparations and urine; and has been also utilized as an indicator electrode for the potentiometric titration of LA.     

Potentiometric sensors based on poly(3,4-ethylenedioxythiophene) (PEDOT) doped with sulfonated calix[4]arene and calix[4]resorcarenes

Potentiometric ion sensors have been prepared by galvanostatic electrosynthesis of the conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) doped with p-sulfonated calix[4]arene (C[4]S) and p-methylsulfonated calix[4]resorcarenes (R_n[4]S) with alkyl substituents of different chain length (R₁=CH₃; R₂=C₂H₅; R₃=C₆H₁₃). The bowl-shape of these doping ions makes them suitable as ionic recognition sites, and their bulky character is expected to prevent them from leaching out of the conducting polymer membrane. For comparison, sensors based on PEDOT doped with poly(styrene sulfonate) (PSS) and poly(vinyl sulfonate) (PVS) were also constructed. The resulting GC/PEDOT electrodes were conditioned in 0.01 mol L^–1 AgNO₃ and their performance as Ag⁺ ion-selective electrodes (ISEs) studied. Results reveal that selectivity and lifetime of the electrodes is affected by the doping anion structure, although all electrodes show selectivity towards Ag⁺ ions. Interaction of Ag⁺ with sulfur atoms present in the conducting polymer backbone is considered to be the main reason for this behavior. A second set of electrodes was constructed and conditioned in 0.1 mol L^–1 KCl. These electrodes were tested in chloride solutions of quaternary ammonium cations, showing that C[4]S and R₂[4]S exhibit significant sensitivity towards pyridinium.Dedicated to Professor György Horányi on the occasion of his 70th birthday in recognition of his outstanding contributions to electrochemistry     

Highly conductive PEDOT/PSS microfibers fabricated by wet-spinning and dip-treatment in ethylene glycol

Highly conductive microfibers made of poly(3,4-ethylenedioxythiophene) doped with poly(4-styrenesulfonate) (PEDOT/PSS) were fabricated by wet-spinning and subsequent dip-treatment in ethylene glycol. The electrical conductivity of the PEDOT/PSS microfibers with a diameter of ca. 5 μm was significantly increased from 74 S cm⁻¹ to 467 S cm⁻¹ by the dip-treatment in 3 min. The result was explained by removal of insulating PSS from the surface of the PEDOT/PSS grains and crystallization of PEDOT, which led to the formation of large numbers of higher conductive grains that enhanced the transport of charge carriers in the microfiber. The mechanical properties of the microfibers were also improved by the dip-treatment where Young’s modulus and tensile strength increased from 3.2 GPa and 94 MPa to 4.0 GPa and 130 MPa, respectively.     

Formation of ultra-thin prussian blue layer on carbon steel that promotes adherence of hybrid polypyrrole based protective coating

Electrodeposition of well-adhering polypyrrole-based hybrid films containing hexacyanoferrate(II,III) anions from neutral solutions of pyrrole and potassium hexacyanoferrate(II) on medium carbon (0.48% C) steel has been described. The resulting polypyrrole coatings that are doped with hexacyanoferrate(II,III) anions show protective properties against pitting corrosion of carbon steel substrates in strongly acidic media containing chlorides (0.1 mol dm^–3 HCl + 0.4 mol dm^–3 NaCl). Polypyrrole acts as a stable host matrix for inorganic anions. The presence of negatively charged species (hexacyanoferrates) in the polymer backbone tends to block the access of pitting-causing anions (chlorides) to the surface of steel. The Fe(CN)₆^3-/4– anions existing in the vicinity of steel substrate stabilizes its surface by forming an overcoating in the form of sparingly soluble metal hexacyanoferrate, mostly Prussian blue (PB), microstructures. It has been demonstrated that by applying cyclic voltammetry and X-ray photoelectron spectroscopy, the presence of traces of free cyanide anions promotes the formation of PB on carbon steel surface which results in increasing the adherence of polypyrrole-based films to the metallic substrate. Morphology of the protective composite films is also addressed.Dedicated to Prof. G. Horanyi on the occasion of his 70th birthday     

Direct potentiometry and potentiotitrimetry of warfarin and ibuprofen in pharmaceutical preparations using PVC ferroin-based membrane sensors

Sensitive and fast-responding potentiometric sensors are described for the determination of warfarin and ibuprofen. They consist of PVC matrix membranes containing the drag-ferroin ion-association complexes as electroactive materials and dioctylphthalate as a solvent mediator. Linear dynamic response range between 1 × 10^–2 and 2 × 10^–5 M with Nernstian slopes of 59–60 mV/decade concentration and a detection limit of 0.8–1.3 g/ml are obtained. A wide range of organic anions and drag excipients do not interfere. Titration of the drugs with a standard ferroin solution using either a drag-ferroin or ferroin-TPB PVC sensor in conjunction with an Ag-AgCl reference electrode displaysS-shaped titration curves with sharp potential breaks at stoichiometric 12 (ferroin:drug) reaction. Differential titration curves with well-defined peaks at the equivalence points are obtained using drug-ferroin/ferroin-TPB PVC membrane sensors. Direct potentiometry and potentiotitrimetry of warfarin and ibuprofen in various pharmaceutical preparations are presented and compared. Several advantages over the pharmacopoeial methods and other techniques in current use are offered by the proposed technique.     

Electroless deposition of silver on poly(3, 4-ethylenedioxythiophene): role of the organic ions used in the course of electrochemical synthesis

The electroless deposition of silver is studied on poly(3, 4-ethylenedioxythiophene) (PEDOT) layers synthesized in the presence of excess of perchlorate ions with and without the addition of two organic dopants: dodecylsulfate (DDS) or polystyrenesulfonate (PSS). Silver deposition is carried out at the expense of oxidation of the pre-reduced PEDOT layers using either Ag⁺ cation or [AgEDTA]^3? complex anion solutions. The amount of deposited silver is monitored by voltammetric stripping. The type of the metal deposit is imaged by SEM. It is found that there are marked differences between the three types of PEDOT with respect to the amount of deposited silver and size distribution of the metallic species. In both silver plating solutions, the largest amount of silver is deposited on PEDOT/DDS, followed by PEDOT/PSS and PEDOT/ClO₄ ^?. These results are discussed in the context of possible structural difference of the three types of PEDOT layers. The comparison between the silver deposits obtained in the two silver plating solutions shows finer dispersion and larger amount of the metallic phase obtained in the presence of the silver complex anions. This solution presents a better opportunity to obtain homogeneous distribution of silver crystalline species on the PEDOT surface.     

Roll‐to‐Roll printed PEDOT/PSS/GO Plastic Film for Electrochemical Determination of Carbofuran

In this work, we developed a roll‐to‐roll printed poly(3,4‐ethylenedioxythiophene)/polystyrene sulphoanate without graphene oxide (GO) (PEDOT/PSS) and with graphene oxide (PEDOT/PSS/GO) plastic films for the electrochemical determination of carbofuran. Both the PEDOT/PSS and PEDOT/PSS/GO plastic films showed electroactivity towards the oxidation of carbofuran. Incorporation of graphene oxide (GO) improves the electrochemical activity of carbofuran and increased its sensitivity. The printed plastic films were characterized by cyclic voltammetry (CV), linear sweep voltammetry (LSV), surface profilometer, four point probe and atomic force microscopy (AFM). The effects of pH, deposition time, deposition potential and film thickness on the oxidation peak current of carbofuran were investigated. Under the optimized conditions, a dynamic linear range of 1 μM–90 μM with a detection limit of 1.0×10^?7 M (S/N=3) were obtained. The printed PEDOT/PSS/GO plastic electrode was applied for the determination of carbofuran in vegetable and fruit samples with recoveries between 94.4 and 101.8 %.