ZnO-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode material for lithium-ion batteries synthesized by a combustion method

ZnO-coated LiMn₂O₄ cathode materials were prepared by a combustion method using glucose as fuel. The phase structures, size of particles, morphology, and electrochemical performance of pristine and ZnO-coated LiMn₂O₄ powders are studied in detail by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), galvanostatic charge-discharge test, and X-ray photoelectron spectroscopy (XPS). XRD patterns indicated that surface-modified ZnO have no obvious effect on the bulk structure of the LiMn₂O₄. TEM and XPS proved ZnO formation on the surface of the LiMn₂O₄ particles. Galvanostatic charge/discharge test and rate performance showed that the ZnO coating could improve the capacity and cycling performance of LiMn₂O₄. The 2 wt% ZnO-coated LiMn₂O₄ sample exhibited an initial discharge capacity of 112.8 mAh g^?1 with a capacity retention of 84.1 % after 500 cycles at 0.5 C. Besides, a good rate capability at different current densities from 0.5 to 5.0 C can be acquired. CV and EIS measurements showed that the ZnO coating effectively reduced the impacts of polarization and charge transfer resistance upon cycling.     

Elevated electrochemical property of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> originated from nano-sized Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>

By employment of nano-sized pre-prepared Mn₃O₄ as precursor, LiMn₂O₄ particles have been successfully prepared by facile solid state method and sol-gel route, respectively. And the reaction mechanism of the used precursors of Mn₃O₄ is studied. The structure, morphology, and element distribution of the as-synthesized LiMn₂O₄ samples are characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Compared with LiMn₂O₄ synthesized by facile solid state method (SS-LMO), LiMn₂O₄ synthesized by modified sol-gel route (SG-LMO) possesses higher crystallinity, smaller average particle size (~175 nm), higher lithium chemical diffusion coefficient (1.17 × 10^?11 cm² s^?1), as well as superior electrochemical performance. For example, the cell based on SG-LMO can deliver a capacity of 85.5 mAh g^?1 at a high rate of 5 °C, and manifests 88.3% capacity retention after 100 cycles at 0.5 °C when cycling at 45 °C. The good electrochemical performance of the cell based on SG-LMO is ascribed mainly to its small particle size, high degree of dispersion, and uniform element distribution in bulk material. In addition, the lower polarization potential accelerates Li⁺ ion migration, and the lower atom location confused degree maintains integrity of crystal structure, both of which can effectively improve the rate capability and cyclability of SG-LMO.     

One-step solid-state synthesis of nanosized LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode material with power properties

A simple one-step solid state reaction way of preparing nanosized LiMn₂O₄ powders with high-rate properties is investigated. Oxalic acid is used as a functional material to lose volatile gases during the process of calcining in order to control the morphology and change the particle size of materials. The results of X-ray diffraction and scanning electron microscopy show that particle size of materials decreases with the increase of the oxalic acid content. The electrochemical test results indicate that optimal LiMn₂O₄ particles (S_0.5) is synthesized when the molar ratios of oxalic acid and total Mn source are 0.5:1. It also manifests that LiMn₂O₄ sample with middle size has the optimal electrochemical performance among five samples instead of the smallest LiMn₂O₄ sample. The obtained sample S_0.5 with middle size exhibits a high initial discharge capacity of 125.8 mAh g^?1 at 0.2C and 91.4% capacity retention over 100 cycles at 0.5C, superior to any one of other samples. In addition, when cycling at the high rate of 10C, the optimal S_0.5 in this work could still reach a discharge capacity of 80.8 mAh g^?1. This observation can be addressed to the fact that the middle size particles balance the contradictory of diffusion length in solid phase and particle agglomeration, which leads to perfect contacts with the conductive additive, considerable apparent Li-ion diffusion rate, and the optimal performance of S_0.5.     

Surfactant-assisted synthesis of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> particles as high-rate and long-life cathode materials for lithium-ion batteries

Herein, we reported the synthesis of uniform LiMn₂O₄ submicroparticles by surfactant-assisted preparation of spherical MnCO₃ precursor followed by solid-state reaction. Polyethylene glycol (Mw = 1000) was used as surfactant to control the morphology and size of the MnCO₃ precursor as well as the MnO₂ intermediate and LiMn₂O₄ product. The influence of particle size, homogeneity, and crystallinity on the electrochemical performance of LiMn₂O₄ was intensively investigated. The test results indicate that the LiMn₂O₄ sample using polyethylene glycol with weight as 10% of reactants shows the best rate capability and long-term cyclability. Due to the homogeneous particles with the average size of ca. 250 nm and high crystallinity, the discharge capacities are as high as 125, 118, 114, and 100 mAh g^?1 at 1, 10, 20, and 50 C rates, respectively, along with high capacity retention of 74% after 1000 cycles at 20 C.     

Modification research of LiAlO<Subscript>2</Subscript>-coated LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> as a cathode material for lithium-ion battery

The LiNi_0.8Co_0.1Mn_0.1O₂ with LiAlO₂ coating was obtained by hydrolysis–hydrothermal method. The morphology of the composite was characterized by SEM, TEM, and EDS. The results showed that the LiAlO₂ layer was almost completely covered on the surface of particle, and the thickness of coating was about 8–12 nm. The LiAlO₂ coating suppressed side reaction between composite and electrolyte; thus, the electrochemical performance of the LiAlO₂-coated LiNi_0.8Co_0.1Mn_0.1O₂ was improved at 40 °C. The LiAlO₂-coated sample delivered a high discharge capacity of 181.2 mAh g^?1 (1 C) with 93.5% capacity retention after 100 cycles at room temperature and 87.4% capacity retention after 100 cycles at 40 °C. LiAlO₂-coated material exhibited an excellent cycling stability and thermal stability compared with the pristine material. These works will contribute to the battery structure optimization and design.     

Hydrothermal synthesis of pure LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> from nanostructured MnO<Subscript>2</Subscript> precursors for aqueous hybrid supercapacitors

Pure LiMn₂O₄ samples with high crystallinity (LMO-1# and LMO-2#) were successfully synthesized by a facile hydrothermal method using δ-MnO₂ nanoflowers and α-MnO₂ nanowires as the precursors. The as-prepared samples were analyzed by XRD, SEM, and Brunauer-Emmett-Teller (BET), and their capacitive properties were investigated by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge/discharge test. Two LiMn₂O₄ samples showed good capacitive behavior in aqueous hybrid supercapacitors. AC//LMO-1# and AC//LMO-2# delivered the initial specific capacitance of 45.4 and 40.7 F g^?1 in 1 M Li₂SO₄ electrolyte at a current density of 200 mA g^?1 in the potential range of 0～1.5 V, respectively. After 1000 cycles, the capacitance retention was 97.6% for AC//LMO-1# and 93.7% for AC//LMO-2#. Obviously, LMO-1# from δ-MnO₂ nanoflowers exhibited higher specific capacitance and better cycling performance than LMO-2#, so LMO-1# was more suitable as the positive electrode material in hybrid supercapacitors.     

Effects of different precipitants on LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> for lithium ion batteries prepared by modified co-precipitation method

Effects of two different precipitants of Na₂CO₃ and Na₂C₂O₄ on LiNi_0.5Mn_1.5O₄ (LNMO) cathode materials, which are prepared by a modified co-precipitation method, have been investigated. Various measurements have been applied to characterize the physical and electrochemical performances of LNMO. Compared with the LNMO prepared by the oxalate co-precipitation (LNMO2), the material synthesized by the carbonate co-precipitation (LNMO1) not only shows more uniform porosity and smaller particles but also has a better rate capability and cycling performance. In addition, the sample prepared by carbonate has a stable spherical structure, due to the fact that carbonate co-precipitation with less gas release during calcination can prevent the destruction of the as-prepared LNMO material structure and promote the formation of regular particle and aperture. Based on the electrochemical test results, LNMO1 shows greatly enhanced electrochemical performance of a high initial discharge capacity of 125.6 mAh g^?1 at 0.25 °C, as well as a preferably capacity retention of 96.5% after 100 cycles at 0.5 °C. And even at a high rate of 10 °C, the discharge capacity of LNMO1-based cell still approaches 83.1 mAh g^?1.     

Lithium polyacrylate-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode materials with excellent performance for lithium ion batteries

A novel facile approach to coat LiMn₂O₄ by lithium polyacrylate (PAALi) is demonstrated. The PAALi-coated LiMn₂O₄ (LMO@2%PAALi) and LiMn₂O₄ (LMO) are characterized by charge–discharge tests, X-ray diffraction (XRD), PAALi dissolving experiment, transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetry (TG), and inductively coupled plasma optical emission spectrometer (ICP-OES). XRD and FTIR analyses indicate that there are no clear differences between LMO@2%PAALi and LMO. PAALi dissolving experiment indicates that PAALi is indissolvable in LiPF₆-EC/DMC/EMC electrolyte. TEM results reveal that LiMn₂O₄ particles are coated by PAALi. ICP-OES results indicate that this stable PAALi coating can prevent the Mn ions dissolving from active LiMn₂O₄ materials and then the stability of LiMn₂O₄ crystals in electrolyte are greatly enhanced. These unique features ensure that LMO@2%PAALi possesses much better rate performance, higher discharge capacity, better cycling performance, and lower charge transfer resistance over LMO. The discharge capacity of LMO@2%PAALi at 0.2 C reaches up to 127.2 mAh g^?1 at room temperature.     

Low content Ni and Cr co-doped LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> with enhanced capacity retention

Nanoparticles of the pure and Ni–Cr co-doped lithium manganese oxides Li[Ni_xCr_yMn_2-x-y]O₄ (x = y = 0.01–0.05) have been synthesized by sol–gel method using citric acid as a chelating agent. The effect of low-content doping was noted reflecting the faster ionic movement in the cathode material. The phase structure and morphology of the materials are characterized by XRD, FTIR, SEM and TEM. Electrochemical and impedance measurements established that low-content Ni–Cr substitution substantially improves the structural stability and high rate cycling performance of LiMn₂O₄. Among all the investigated compositions, LiNi_0.01Cr_0.01Mn_1.98O₄ demonstrated the best electrochemical performance. At a substantially high current rate of 5 C, 82% of the initial discharge capacity at 0.1 C is retained. Remarkably, after deep cycling at high rates, a discharge capacity of 104 mAhg^?1 is resumed upon reducing the current rate to 0.1 C which is 91% of the specific capacity in the first cycle.     

Ionic liquid-based electrolyte with dual-functional LiDFOB additive toward high-performance LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> batteries

Manganese oxide-based cathodes are one of the most promising lithium-ion battery (LIB) cathode materials due to their cost-effectiveness, high discharge voltage plateau (above 4.0 V vs. Li/Li⁺), superior rate capability, and environmental benignity. However, these batteries using conventional LiPF₆-based electrolytes suffer from Mn dissolution and poor cyclic capability at elevated temperature. In this paper, the ionic liquid (IL)-based electrolytes, consisting of 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfon)imidate (PYR_1,4-TFSI), propylene carbonate (PC), lithium bis(trifluoromethanesulfon)imide (LiTFSI), and lithium oxalyldifluoroborate (LiDFOB) additive, were explored for improving the high temperature performance of the LiMn₂O₄ batteries. It was demonstrated that LiTFSI-ILs/PC electrolyte associated with LiDFOB addition possessed less Mn dissolution and Al corrosion at the elevated temperature in LiMn₂O₄/Li batteries. Cyclic voltammetry and electrochemical impedance spectroscopy implied that this kind of electrolyte also contributed to the formation of a highly stable solid electrolyte interface (SEI), which was in accordance with the polarization measurement and the Li deposition morphology of the symmetric lithium metal cell, thus beneficial for improving the cycling performance of the LiMn₂O₄ batteries at the elevated temperature. Cyclic voltammetry and electrochemical impedance spectroscopy implied that the cells using this kind of electrolyte exhibited better interfacial stability, which was further verified by the polarization measurement and the Li deposition morphology of the symmetric lithium metal cell, thus beneficial for improving the cycling performance of the LiMn₂O₄ batteries at the elevated temperature. These unique characteristics would endow this kind of electrolyte a very promising candidate for the manganese oxide-based batteries.     

Vertical aligned V<Subscript>2</Subscript>O<Subscript>5</Subscript> nanoneedle arrays grown on Ti substrate as binder-free cathode for lithium-ion batteries

V₂O₅ nanoneedle arrays were grown directly on titanium (Ti) substrate by a facile solvothermal route followed with calcination at 350 °C for 2 h. The as-prepared V₂O₅ nanoneedles are about 50 nm in diameter and 800 nm in length. The electrochemical behavior of V₂O₅ nanoarrays as binder-free cathode for lithium-ion batteries (LIBs) was evaluated by cyclic voltammetry and galvanostatic discharge/charge tests. Compared with V₂O₅ powder electrode, V₂O₅ nanoneedle arrays electrode exhibited improved electrochemical performance in terms of high discharge capacity of 262.5 mA h g^?1 between 2.0 and 4.0 V at 0.2 C, and high capacity retention up to 77.1% after 100 cycles. Under a high current rate of 2 C, a discharge capacity of about 175.6 mA h g^?1 can be maintained. The enhanced performance are mainly due to the intimate contact between V₂O₅ nanoneedle active material and current collector, which enable shortened electron transfer pathway and improved charge transfer kinetics, demonstrating their potential applications in high rate electrochemical storage devices.     

CeO<Subscript>2</Subscript> coating to improve the performance of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript>

The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ coated with CeO₂ has been fabricated by an ionic interfusion method. Both the bare and the CeO₂-coated samples have a typical layered structure with R-3m and C2/m space group. The results of XRD and TEM images display that the CeO₂ coating layer on the precursor could enhance the growth of electrochemically active surface planes ((010), (110), and (100) planes) in the following ionic interfusion process. The results of galvanostatic cycling tests demonstrate that the CeO₂-coated sample has a discharge capacity of 261.81 mAh g^?1 with an increased initial Coulombic efficiency from 62.4 to 69.1% at 0.05 °C compared with that of bare sample and delivers an improved capacity retention from 71.7 to 83.4% after 100 cycles at 1 °C (1 °C?=?250 mA g^?1). The results of electrochemical performances confirm that the surface modification sample exhibits less capacity fading, lower voltage decay, and less polarization.     

Electrochemical properties of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> prepared with tartaric acid chelating agent

Lithium manganese oxide (LiMn₂O₄) has been prepared using sol-gel technique under acidic (pH = 5.8) and alkaline (pH = 9) conditions with tartaric acid as chelating agent. X-ray studies show that under acidic condition, an Mn₂O₃ peak was observed indicating the presence of impurities. No impurity was observed for LiMn₂O₄ under alkaline conditions. The particle size is mostly in the range of 124 to 185 nm from HR-TEM. The lithium diffusion coefficient, D _Li+ in LiMn₂O₄ is of the order 10^?9 cm² s^?1. By using density functional theory (DFT) calculations, structural properties have been obtained. The specific discharge capacity of the cells with LiMn₂O₄ prepared under alkaline condition and with LiMn₂O₄ prepared under acidic condition discharged at 0.5 C is in the ranges of 132 to 142 and 128 to 139 mAh g^?1, respectively.     

Improvement in rate capability of lithium-rich cathode material Li[Li<Subscript>0.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>]O<Subscript>2</Subscript> by Mo substitution

Lithium-rich cathode material Li[Li_0.2Ni_0.13Co_0.13Mn_0.54]O₂ doped with trace Mo is successfully synthesized by a sol-gel method. The X-ray diffraction patterns show that trace Mo substitution increases the inter-layer space of the material, of which is benefiting to lithium ion insertion/extraction among the electrode materials. The (CV) tests demonstrate the decrease of polarization, and on the other hand, the lithium ion diffusion coefficient (D _Li) of the modified material turns out to be larger, which indicates a faster electrochemical process. As a result, the Mo doped material possesses high rate performance and good cycling stability, and the initial discharge capacity reaches 149.3 mAh g^?1 at a current density of 5.0 °C, and the residual capacity is 144.0 mAh g^?1 after 50 cycles with capacity retention of 96.5 % in the potential range of 2.0–4.8 V at room temperature.     

Effects of doping Al on the structure and electrochemical performances of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> cathode materials

The Li-rich cathode material Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ had been successfully synthesized by a carbonate coprecipitation method. The effects of substituting traces of Al element for different transitional metal elements on the crystal structure and surface morphology had been investigated by X-ray diffraction (XRD) and field emission scanning electron microscopy. The results revealed that all the materials showed similar XRD patterns and surface morphology. It was demonstrated that LNCMAl1 exhibited the superior electrochemical performance. The discharge capacity was 265.2 mAh g^?1 at 0.1 C and still maintained a discharge capacity of 135.6 mAh g^?1 at 5.0 C. The capacity retention could still be 58.2 and 66.8% after 50 cycles at 1.0 and 2.0 C, respectively. Electrochemical impedance spectra results proved that the remarkably improved rate capability and cycling performance could be ascribed to the low charge transfer resistance and enhanced reaction kinetics.     

Improvement of cycling and thermal stability of LiNi<Subscript>0.8</Subscript>Mn<Subscript>0.1</Subscript>Co<Subscript>0.1</Subscript>O<Subscript>2</Subscript> cathode material by secondly treating process

(Ni_0.8Mn_0.1Co_0.1)(OH)₂ and Co(OH)₂ secondly treated by LiNi_0.8Mn_0.1Co_0.1O₂ have been prepared via co-precipitation and high-temperature solid-state reaction. The residual lithium contents, XRD Rietveld refinement, XPS, TG-DSC, and electrochemical measurements are carried out. After secondly treating process, residual lithium contents decrease drastically, and occupancy of Ni in 3a site is much lower and Li/Ni disorder decreases. The discharge capacity is 193.1, 189.7, and 182 mAh g^?1 at 0.1 C rate, respectively, for LiNi_0.8Mn_0.1Co_0.1O₂-AP, -NT, and -CT electrodes between 3.0 and 4.2 V in pouch cell. The capacity retention has been greatly improved during gradual capacity fading of cycling at 1 C rate. The noticeably improved thermal stability of the samples after being treated can also be observed.     

Synthesis of hierarchical Na<Subscript>2</Subscript>FeP<Subscript>2</Subscript>O<Subscript>7</Subscript> spheres with high electrochemical performance via spray drying

Hierarchical Na₂FeP₂O₇ spheres with nanoparticles were successfully fabricated by a facile spray drying method. A relatively low drying temperature was introduced in order to form a carbon layer on the surface. As a cathode material for sodium-ion batteries, it delivered a reversible capacity of 84.4 mAh g^?1 at 0.1 C and showed excellent cycling and rate performance (64.7 mAh g^?1 at 5 C). Furthermore, a full sodium battery was fabricated using SP-Na₂FeP₂O₇ as the cathode and hard carbon as the anode, suffering almost no capacity loss after 400 cycles at 1 C. Due to its superior electrochemical property and the low materials cost, Na₂FeP₂O₇ is becoming a promising cathode material for large-scale energy storage systems.     

Electrochemical comparison of LiFe<Subscript>0.4</Subscript>Mn<Subscript>0.595</Subscript>Cr<Subscript>0.005</Subscript>PO<Subscript>4</Subscript>/C and LiMnPO<Subscript>4</Subscript>/C cathode materials

A comparison of electrochemical performance between LiFe_0.4Mn_0.595Cr_0.005PO₄/C and LiMnPO₄/C cathode materials was conducted in this paper. The cathode samples were synthesized by a nano-milling-assisted solid-state process using caramel as carbon sources. The prepared samples were investigated by XRD, SEM, TEM, energy-dispersive X-ray spectroscopy (EDAX), powder conductivity test (PCT), carbon-sulfur analysis, electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge cycling. The results showed that LiFe_0.4Mn_0.595Cr_0.005PO₄/C exhibited high specific capacity and high energy density. The initial discharge capacity of LiFe_0.4Mn_0.595Cr_0.005PO₄/C was 163.6 mAh g^?1 at 0.1C (1C = 160 mA g^?1), compared to 112.3 mAh g^?1 for LiMnPO₄/C. Moreover, the Fe/Cr-substituted sample showed good cycle stability and rate performance. The capacity retention of LiFe_0.4Mn_0.595Cr_0.005PO₄/C was 98.84 % over 100 charge-discharge cycles, while it was only 86.64 % for the pristine LiMnPO₄/C. These results indicated that Fe/Cr substitution enhanced the electronic conductivity for the prepared sample and facilitated the Li⁺ diffusion in the structure. Furthermore, LiFe_0.4Mn_0.595Cr_0.005PO₄/C composite presented high energy density (606 Wh kg^?1) and high power density (574 W kg^?1), thus suggested great potential application in lithium ion batteries (LIBs).     

Improving the electrochemical performance of Li-rich Li<Subscript>1.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>O<Subscript>2</Subscript> cathode material by LiF coating

To suppress the capacity fade of Li-rich Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material as cathode materials for lithium-ion battery, we introduce a LiF coating layer on the surface to improve the cycling performance of Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material. The modified sample shows a capacity of 163.2 mAh g^?1 with a capacity retention of 95% after 100 cycles at a current density of 250 mA g^?1, while the pristine sample only delivers a capacity of 129.9 mAh g^?1 with a capacity retention of 82%. Compared with the pristine material, the LiF-modified sample exhibits an obvious enhancement in the electrochemical performance, which will be very beneficial for this material to be commercialized on the new energy vehicles and other related areas.     

Preparation of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode materials by electrospinning

LiNi_0.5Mn_1.5O₄ cathode material was prepared by electrospinning using lithium hydroxide, manganese acetate, nickel acetate, acetic acid, ethanol, and poly(vinyl pyrrolidone) as raw materials. The effect of calcination temperature on the structure, morphology, and electrochemical properties was investigated. XRD results indicate that the LiNi_0.5Mn_1.5O₄ composite is well crystallized as a spinel structure at calcination temperature of 650 °C for 3 h. SEM results reveal that this composite has a nanofiber shape with average size of about 300–500 nm. Electrochemical performance tests reveal that this composite shows the initial discharge capacity of 127.8 and 105 mAhg^?1 at 0.1 and 3 C rates, respectively, and exhibits good cycling performance.