一种辐射零点可控的紧凑型滤波贴片天线

提出了一种辐射零点可控的紧凑型滤波贴片天线。该滤波天线以基本的微带贴片天线为原型,主要由一个简单的金属辐射贴片和两个对称的分割形槽组成。两个分割形槽蚀刻在金属贴片上,使得高/低频段分别产生两个宽边辐射零点,从而引入滤波选频功能。该结构未引入额外滤波电路和其他寄生单元,节省了空间尺寸,结构更加紧凑;两个辐射零点独立可控,提高了设计的灵活度。且在实现滤波选频功能的同时,对天线增益的影响很小。利用HFSS仿真软件优化滤波天线结构,制作了一个实物模型并进行了测试。测试结果与仿真结果基本一致。测试结果表明,提出的滤波天线工作在2.40 GHz,两个独立可控的辐射零点分别位于1.96 GHz和2.66 GHz,平均实际增益约为7.0 dBi,带外抑制水平超过39 dB。     

等离子体天线色散关系和辐射场数值计算

研究了电磁波沿轴向对称柱形等离子体天线传播的特性、色散关系及辐射方向图、增益等天线参数.通过对腔体材料介电系数、内外半径、等离子体密度、碰撞频率等参数的分析，结果表明要减小波沿等离子体天线传播的衰减，应当增加等离子体密度，减小碰撞频率，增加等离子体半径，减小腔体厚度，采用介电系数较小的材料.计算了在不同参数条件下，等离子体天线的辐射方向图、增益的变化，这些结果对于等离子体天线的设计很有参考价值. 关键词： 等离子体天线 色散关系 增益 辐射方向图     

可调频高功率宽谱微波的产生和辐射

 设计了一种可调谐频率的高功率宽谱微波辐射装置,装置由可调谐长度的1/4波长低阻同轴谐振器、环形开关、电容耦合器和宽谱辐射天线组成,中心频率调谐为200～400 MHz。低阻传输线与环形开关构成1/4波长短路谐振器,它产生的宽谱微波振荡通过耦合器耦合到宽谱辐射天线上辐射,而耦合器由集中电容与分布电感组成,实现宽谱微波在频率调谐范围内以较为一致的耦合度提取微波能量。通过转动螺杆滑动安装在同轴谐振器内芯上的环形开关,达到改变谐振频率的目的。最后,将可调频宽谱辐射装置与输出电压为500 kV的Tesla变压器脉冲功率源联试,得到200～400 MHz宽谱微波辐射,辐射因子为95～130 kV,频谱百分比带宽为10%～30%。     

Design of a low-frequency miniaturized piezoelectric antenna based on acoustically actuated principle

An acoustically actuated piezoelectric antenna is proposed for low frequency (LF) band in this paper. The proposed antenna is theoretically calculated, numerically optimized by the finite element method (FEM), and experimentally analyzed. The measurement results show that the near-field radiation pattern of the piezoelectric antenna is similar to that of the electric dipole antenna. The radiation efficiency of the piezoelectric antenna is 3－4 orders of magnitude higher than that of electrically small antenna (ESA), with their sizes being the same size, and the maximum transmission distance obtained experimentally is 100 cm, which can be improved by increasing the input power. In addition, the gain, directivity, and quality factor of piezoelectric antenna are also analyzed. In this paper, traditional antenna parameters are creatively used to analyze the performance of piezoelectric antenna. The research conclusions can provide reliable theoretical basis for realizing LF antenna miniaturization.     

基于缺陷接地结构的太赫兹双频微带天线

提出了一种工作在太赫兹频段的双频微带天线。在普通矩形微带天线的基础上,在辐射贴片上加载45°和135°的矩形贴片增大辐射面积,增大高频谐振点处阻抗带宽。通过引入缺陷接地结构使得天线在接地板处的电流路径改变,并与辐射贴片相互耦合,从而实现双频特性。为提高天线增益,在辐射贴片边缘加载若干寄生矩形贴片,并增加了寄生贴片处的基板厚度。该款天线可以同时在520 GHz(508~532 GHz)和680 GHz(581~766 GHz)的频段下工作,其中高频段的相对带宽达到了27.5%,最大增益达到了3.54 dB和4.11 dB。该双频天线结构相对简单,各项性能指标稳定,对于工作在太赫兹频段上的通信系统和无线传输系统具有一定的应用价值。     

光电导天线辐射阻抗特性模拟分析(英文)

针对连续太赫兹光电导天线辐射功率较低的缺点,利用有限积分方法对三种常用的光电导天线,包括偶极天线、蝶形天线和螺旋天线,进行数值模拟并分析比较其辐射阻抗特性.仿真结果表明,偶极天线的辐射阻抗与偶极长度、宽度、电极间隙以及传输线宽度有关,且在其谐振频率存在峰值阻抗,适用于特定频率的太赫兹波辐射.蝶形天线和螺旋天线在所研究的太赫兹波段具有近似稳定的辐射阻抗,广泛应用于宽带领域.对带有交叉电极的电极间隙进行计算,结果表明由交叉电极引入的附加电容降低了天线的高频阻抗.     

环状烯烃聚合物基底材料的太赫兹复介电常数和损耗特性研究

太赫兹时域光谱(THz-TDS)已被用于研究包括液体,半导体,爆炸物和气体等多种材料。然而自由空间太赫兹光谱系统存在着一些检测局限性,如微量物质难以被检测、系统尺寸难以实现微型化、空气中水的强烈吸收引起的信号衰减较大等问题。为了解决这些问题,研究人员设计了基于金属波导传输线结构的太赫兹芯片集成器件,通过飞秒红外激光激励传输线上的光电导材料实现太赫兹波的产生和检测。然而,在这些芯片上传输的太赫兹信号的频谱宽度很难达到自由空间太赫兹时域光谱系统的频带宽度,一个重要原因是由于传输信号受到随频率增加的传输线损耗所导致的衰减。通常这些损耗主要由三个部分组成：导体损耗,介电损耗和辐射损耗。研究表明：使用低介电常数材料作为共面传输线的衬底,将减少这种介电常数的失配,从而避免冲击波辐射损失;使用具有低损耗角正切的基底材料可以减少太赫兹传输线的损耗。环烯烃聚合物(COP)是一种具有环状烯烃结构的非晶性透明共聚物的材料,在太赫兹波段具有很高的透射率,为了探究这种材料是否能用于共面传输线的衬底,需要通过太赫兹时域光谱技术和介电函数理论分析它在太赫兹频段的光谱和介电特性,以及对这种材料作为基底时用在太赫兹传输线的传输特性进行仿真计算分析。使用透射式太赫兹时域光谱系统,对三种COP、熔融石英和PMMA进行了光谱测试,提取了它们的透射时域信号,采用Dorney和Duvillaret等提出的物理模型计算复介电函数。实验表明：与其他两种材料相比,COP材料在1 THz处的透过率更高,可以达到94.5%,同时介电损耗和介电常数更低,其中介电损耗在1 THz处达到4.31×10-4,因此将COP作为传输线基底材料时能有效减少基底的介电损耗。同时COP材料的介电常数在0.2～2.8 THz范围内维持在约2.3的水平,也有效减弱了辐射损耗。对实验材料基底组成的共面波导传输线进行了HFSS模拟,获得了它们的正向传输衰减系数(S₂₁ parameter),并对由基底引起的介电损耗和辐射损耗进行了计算分析。模拟和计算结果也表明在同一传输线结构下,与其他材料相比COP作为基底时的损耗更小。通过太赫兹时域光谱法与介电响应分析,表明了在太赫兹波段具有较低介电常数的COP材料更适合作为太赫兹传输线结构的基底材料,它可以有效的降低因基底引起的介电损耗和辐射损耗。这为太赫兹传输线的设计过程中衬底材料的选择与应用提供了实验和理论依据。     

Ƶ�ʵ��ƶ�ICRH �����迹ƥ���Ӱ���о�

采用三支节液态调配器使离子回旋加热(ICRH)天线系统达到阻抗匹配,在阻抗匹配的条件下结合频率调制技术来减小由天线输入阻抗变化所引起的反射功率。数值模拟了频率调制前后天线负载与反射系数的变化关系,用来验证频率调制对ICRH天线中阻抗匹配装置的影响。模拟结果表明:三支节液态调配器结合频率调制方法,能更好地降低天线传输系统的反射系数,使得发射机的功率通过天线辐射更加有效地耦合到等离子体中去。     

Lower RCS directional antenna by left-handed material

We theoretically study the radiation of a current line source with a surrounding cylindrical shell of left-handed material (LHM). The far-field radiation pattern is obtained by solving the Maxwell equation in a cylindrical coordinate, which show that this radiation system has good directional emission characteristics and can be used as a directive antenna. The directive emission is explained due to the negative refraction and the focus effect occurring at the interface of the LHM shell. Compared with the parabolic reflector antenna with the same aperture size, our antenna has lower radar cross-section (RCS) in a broadband frequency range, providing a way to realize lower RCS antenna.     

频率调制对ICRH 天线阻抗匹配的影响研究

采用三支节液态调配器使离子回旋加热(ICRH)天线系统达到阻抗匹配,在阻抗匹配的条件下结合频率调制技术来减小由天线输入阻抗变化所引起的反射功率。数值模拟了频率调制前后天线负载与反射系数的变化关系,用来验证频率调制对ICRH 天线中阻抗匹配装置的影响。模拟结果表明：三支节液态调配器结合频率调制方法,能更好地降低天线传输系统的反射系数,使得发射机的功率通过天线辐射更加有效地耦合到等离子体中去。     

Optical microstrip patch antennas design and analysis

This paper has presented transparent conductor oxide materials (TCOMs) based microstrip patch antennas with glass substrate and copper ground plane, which have been deeply analyzed in the visible spectrum region in comparison with the practical patch antenna model of indium tin oxide patch with glass substrate and different TCOMs based ground plane. As well as the study have investigated the effect of transparent oxide materials on patch antenna design instead of perfect conductor materials such as copper that has low cost and weight. The tradeoff between optical transparency and electrical conductivity will be evaluated for a range of visible regions. Microstrip transmission line feed method is used to predict the skin effects on a patch antenna and their impact on antenna efficiency, resonance frequency and optical transmission are also described. This study have discussed assessment of these tradeoffs and effect of TCOMs parameters on antenna design.     

TEM喇叭天线辐射机理分析和优化设计

在频域和时域研究了TEM喇叭天线的辐射机理。在频域,高频信号激励的TEM喇叭表现为口径天线的辐射特性,具有良好的方向性;低频信号激励的TEM喇叭可视作偶极子天线,具有全向辐射特性;在时域,脉冲激励的TEM喇叭天线辐射场由四个子波叠加构成,在不同方向上,各个子波的波形和相对时序不同,导致不同方向上辐射场波形也不相同。根据辐射机理研究结果,提出了一种TEM喇叭天线末端加载设计并给出了其优化设计方法,有效地改善了天线主轴辐射性能,提高了辐射因子和天线效率。     

Millimeter wave components for electronically controllable antennas

Many present and future military and commercial systems operating at millimeter wave frequencies require the use of sophisticated electronically controllable antennas for maximum capability and flexibility. Electronic control of the antenna pattern is provided by electronically switchable phase control of each radiating element such as that achieved in phased array antennas or via electronically reconfigurable antenna feeds referred to as beam forming networks (BFN). Multibeam antennas provided by BFN'S can be realized using switches, variable power dividers (VPD), and phase shifters. Ferrite materials and associated application technology are being utilized to achieve these switchable RF control components at millimeter wave frequencies. The performance achievable in ferrite switchable circulators, variable power dividers and phase shifters in the frequency region from 20 to 100 GHz is discussed.     

Radiation characteristics of dipole antenna in a grounded composite magnetized semiconductor plasma

The radiation characteristics of dipole antenna in a grounded nonreciprocal semiconductor plasma are examined using the spectral domain-exponential matrix technique, and such solid plasma is taken as GaAs material. The effects of constitutive and geometrical parameters of the semiconductor plasma on the radiation patterns are demonstrated in detail, and the results show that the far-field behaviour of dipole antenna can be changed by adjusting both the operating frequency and the applied magnetic field, et al.     

Effective wavelength scaling for optical antennas

In antenna theory, antenna parameters are directly related to the wavelength lambda of incident radiation, but this scaling fails at optical frequencies where metals behave as strongly coupled plasmas. In this Letter we show that antenna designs can be transferred to the optical frequency regime by replacing lambda by a linearly scaled effective wavelength lambda(eff)=n(1)+n(2)lambda/lambda(p), with lambda(p) being the plasma wavelength and n(1), n(2) being coefficients that depend on geometry and material properties. It is assumed that the antenna is made of linear segments with radii R < lambda. Optical antennas hold great promise for increasing the efficiency of photovoltaics, light-emitting devices, and optical sensors.     

切比雪夫渐变线TEM喇叭天线数值模拟

设计了一种采用切比雪夫渐变线的TEM喇叭天线,分析了其工作原理,采用数值模拟的方法研究了其阻抗特性、传输特性与辐射特性,并在不同的馈入脉冲下与常用的线性渐变TEM喇叭天线进行了性能对比。结果表明:切比雪夫渐变线TEM喇叭天线具有低反射、高带宽和高辐射场强的优点,其性能要明显优于线性渐变TEM喇叭天线,且馈入脉冲越宽,性能越明显。分析了最大反射系数对切比雪夫渐变线TEM喇叭天线辐射性能的影响,馈入脉冲越窄时,宜选择反射系数越大的辐射天线。     

Theoretical Analysis and Experimental Measurement of Digital Multi-Beam Phased Antenna Array in the C-Range

The choice of element for constructing a phased antenna array (PAA) providing a relative frequency bandwidth up to 9% for the transmission or reception of wireless communication system information was carried out. There are three methods to suppress of side lobes and diffraction of PAA in the radiation far field. Superposition of excitation signals of a flat PAA for simultaneous emission of several independent beams in a radiation far field was used. Сalculation and optimization of progressive distribution of phase shifts in the excitation signal group in the horizontal and vertical directions in the plane of PAA for radiation (reception) of independent beams in spherical coordinates (azimuth and elevation) in space was performed. An experimental sample of a phased antenna array was developed using microstrip technology, which forms several beams in a radiation far field. An experimental measurement of the voltage standing wave ratio and relative frequency bandwidth of the sample developed by phased array microstrip and printing technology was carried out.     

Effect of spiral left-handed material with near-zero index on rectangular microstrip antenna

In this paper, spirals are arranged periodically on the surface of the substrate, making a left-handed material (LHM) with a near-zero index of refraction. A radiation patch is etched on the surface of this substrate, making an antenna. The finite difference time domain method is used to study the effect of this LHM with a near-zero index of refraction on the microstrip. At f=13.78 GHz, the equivalent permittivity and permeability of the proposed spiral materials are both negative; at f=28.02 GHz, the equivalent permittivity and permeability are both negative and the refraction index is near zero. Compared with conventional microstrip antenna, the radiation gain of the antenna is much higher and the return loss is much lower due to the near-zero-index effect.     

基于矩形波导缝隙馈电的阵列天线设计

提出一种具有高功率容量的直线阵列天线,该天线阵基于矩形波导缝隙馈电,馈电耦合结构采用新型的弧形耦合缝隙,利用小螺旋天线作为辐射单元,通过旋转螺旋线内导体来调整各个辐射单元相位,从而实现一维波束扫描。采用等效传输法进行理论设计,数值模拟结果表明,该长度为3200 mm的单元天线在中心频率8.40 GHz上可获得的增益为27.50 dB,主瓣轴比为0.51 dB。功率容量约90 MW,辐射效率为97.10%,反射低于-24 dB,波束扫描范围±38°。     

Strip dielectric wave guide antenna-for the measurement of dielectric constant of low-loss materials

The value of dielectric constant are the most important parameters in material science technology. In micro-wave and millimeter wave circuits using dielectric materials the values of this parameters should be known accurately. It is observed that the number of methods are reported in litrature, however these methods impose difficulties in experimentation and are not very accurate. In this paper a novel approach to the measurement of the dielectric constant of low loss materials at micro-wave and millimeter wave frequencies has been discussed. In this method by using antenna theory, a metallic strip dielectric guide is taken in to constideration and band reject phenomenon of dielectric antenna is used. Frequency response of an antenna in band reject mode is a function of the dimensional parameters, such as the metallic strip period, the profile of the metallic strip and the dielectric constant of the material used. Hence if one measure the frequency responce of the antenna in band reject mode, the dielectric constant of the material is determined provided all other parameters are known. This method gives a direct measure of dielectric constant and is quite accurate as computer techniques are used for evaluating the dielectric constant. This method verified experimentally also.