接枝环氧树脂/硅溶胶杂化水分散液的制备与表征

利用原位分散法制备了接枝环氧树脂 硅溶胶杂化水分散液 ,并通过红外光谱和 ζ电位测定 ,表征了接枝环氧树脂与硅溶胶之间的杂化作用 .实验结果表明 ,与接枝环氧树脂水分散液相比 ,杂化水分散液的粒径和粘度均减小 .按此探讨了形成杂化水分散液的历程 .初步测定了杂化水分散液成膜后的表面性能 ,发现它们具有更高的硬度和更好的疏水性能 ,与成膜过程中硅溶胶在膜表面的富集效应有关     

混合型环氧树脂水分散液的制备与表征

以苯乙烯和甲基丙烯酸的共聚物[P(St-co-MAA)]作为分散剂和高分子量的环氧树脂在120℃下混合,制备了环氧树脂水分散液。测定了环氧树脂与P(St-co-MAA)混合前后的环氧值,证明共聚物中的部分羧基和环氧基团发生反应,形成了接枝共聚物,P(St-co-MAA)与环氧树脂之间的相容性良好,从而制得稳定性良好而且粒径较小的水分散液。同时考察了共聚物组成和环氧树脂分子量时水分散液以及成膜后性能的影响。     

从含氢硅油制取水性氟硅聚合物

在无溶剂的条件下, 通过硅氢加成法将烯丙基聚氧乙烯聚氧丙烯醚, 氟化丙烯酸烷基酯接枝共聚到甲基含氢硅油侧链, 成功地合成了一系列有机氟硅聚合物. 通过高速剪切乳化法可制得不同质量投料比时的水性氟硅聚合物水分散物. 采用FTIR, ¹H NMR和TEM对有关产物和乳液进行了结构分析, 并进一步系统研究了水分散物表面张力, 流变性等性能, 结果表明: 质量分数为2.0%的水性氟硅聚合物水分散物的表面张力降低至22.00～26.00 N/m, 其黏度随着剪切速率的增大有剪切变稠现象发生, 且不同质量投料比时, 其粒子粒径大小及形状也有较大差别.     

有机硅改性UV固化水性环氧树脂的研究

以环氧树脂E-51、甲基三乙氧基硅烷为原料,用接枝共聚的方法合成了有机硅改性水溶性UV固化环氧树脂,该方法有效地改善了环氧树脂的柔韧性、水溶解性,提高了成膜物的机械性能,其拉伸强度达到53.5 MPa,断裂伸长率为46.5%,耐冲击性大于50 kg/cm。通过红外光谱、热重分析表征产物的结构和性能,结果表明,有机硅已经成功接枝到环氧树脂的分子上。有机硅改性后环氧树脂在400℃的分解率由之前的60%降至40%。文章同时讨论了有机硅改性水性UV固化环氧树脂合成中反应温度、有机硅种类以及加入量等对UV固化水性环氧树脂成膜物的附着力、耐水性及耐碱性的影响,以此获得最佳反应条件:质量分数为14.4%的甲基三乙氧基硅烷与羧酸改性的环氧树脂在90℃下反应5～6 h。     

PEB/MMA-AN悬浮接枝共聚反应机理

研究了乙烯-1-丁烯共聚物(PEB)弹性体与甲基丙烯酸甲酯(MMA)-丙烯腈(AN)悬浮接枝共聚反应行为及接枝共聚产物对SAN树脂增韧作用随反应时间的变化规律, 用凝胶渗透色谱法和傅里叶变换红外光谱法对接枝共聚产物进行了表征, 分析了接枝共聚反应机理, 推算了接枝链分子量. 结果表明, 体系首先发生链增长自由基向PEB转移终止形成非接枝共聚物(MAN_L)和PEB大分子自由基引发单体共聚形成接枝链(g-MAN)的反应, 接枝反应结束后体系发生明显的非接枝共聚形成非接枝共聚物(MAN_H)的反应; MAN_L的分子量低于g-MAN的分子量, 而g-MAN的分子量明显低于MAN_H的分子量; 在接枝共聚过程中发生已接枝和未接枝PEB断链并随机再接生成多嵌段共聚物的副反应; 在反应初期, 接枝链的AN单元含量接近于非接枝共聚物的AN单元含量, 在反应中后期前者远低于后者.     

环氧树脂复合水分散乳液的制备及其性能研究

通过溶液聚合法制备了丙烯酸单体改性的高相对分子量的环氧树脂复合水分散乳液.利用傅立叶变换红外光谱仪测试了改性聚合物的结构,用ZETA电位分析仪测定了水分散液的粒径及其分布,用透射电子显微镜观察了乳液粒子形态.实验结果表明,改性树脂在水等极性溶剂中有较好的溶解性;随着改性树脂中羧基中和程度的加大,水分散液粒径减小,并成为形状规则的单分散乳液.作者同时进行了改性树脂稀释行为的研究.     

荧光探针法研究聚氨酯水分散液的胶束性质

聚氨酯水分散液是指聚氨酯以分散相分散于连续水性介质中的一种二元胶体体系 .与溶剂型聚氨酯相比 ,这种体系不含或含极少有机溶剂 ,具有不燃、无毒等特点 ,作为涂料和粘合剂使用时不污染空气 ,其粘度和流动性不受聚氨酯分子量的影响 ,可制备成高分子量、高固含量的水分散体系 ,因此获得了广泛的应用并且日益受到人们的重视 ,近 50年来 ,有超过 1 0 0 0份专利发表 ,但是聚氨酯水分散液也存在一些缺陷 ,如贮存稳定性、其膜的耐水耐溶剂性等还不令人满意 ,为了改善耐水耐溶剂性 ,可采用共聚、共混、接枝、交联、形成互穿网络等方法进行结构改…     

氨乙基氨丙基聚二甲基硅氧烷改性水性聚酯型聚氨酯的研究

由聚酯二元醇、异佛尔酮二异氰酸酯和二羟甲基丙酸合成聚氨酯预聚体，以氨乙基氨丙基聚二甲基硅氧(AEAPS)为扩链剂，制备了AEAPS改性聚氨酯水分散液。与未改性的聚氨酯水分散液相比，AEAPS改性聚氨酯水分散液的粒径增大，但粒径分布和表面张力基本不变，说明疏水的聚二甲基硅氧烷侧链被包裹于分散颗粒的内部；此外，改性聚氨酯水分散液的冻融稳定性显著增强。AEAPS改性聚氨酯水分散液成膜后，吸水率明显下降，水在膜表面的接触角增加，400℃时热失重下降，具有良好的疏水性和耐热性。     

过氧化氢与N—甲基苯胺盐酸盐引发体系的研究

在水介质中,研究了新型的过氧化氢/N-甲基苯胺盐酸盐引发体系对 AM 与 PVA 的接枝共聚。产物经紫外光谱、红外光谱和 ~1H-核磁共振进行表征,并提出了引发机理。     

水性聚氨酯甲阶酚醛水分散液微观形态及杂化膜的性能

以自乳化型聚氨酯和甲阶酚醛制备了聚氨酯 酚醛复合水分散液 .pH值与酚醛溶解度的关系表明甲阶酚醛的溶解是酚羟基电离的结果 .聚氨酯 甲阶酚醛水分散液粒子的形态有核壳结构、不完善的核壳结构及纯聚氨酯颗粒三种 ,后者粒径最小 .随着酚醛用量的增大 ,粒子平均粒径增大 .酚醛含量增加使体系热稳定性、机械稳定性、冻融稳定性及临界聚沉值下降 ,pH值稳定范围变窄 .分散液稳定性和电性能考察证明 ,本复合分散液的稳定性主要由分散液的电性能所决定 ,属真溶胶 ,但在一定程度上也具有大分子溶液的特性 .复合液涂膜的性能较纯聚氨酯有所改善 ,尤其在添加了硅溶胶之后     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。