The role of Bi2O3 as a network modifier and a network former in xBi2O3 · (1 − x)LiBO2 glass system

The effect of Bi₂O₃ on the glass transition temperature, electrical conductivity and structure of LiBO₂ glass has been investigated. T_g vs. composition curve shows three different linear regions, while there is an overall decrease in T_g with the increase in Bi₂O₃ content. The slope of these three straight lines is in a decreasing order. These results are interpreted in terms of the increase in the number of non-bridging oxygen atoms, substitution of Bi-O bond in place of B-O bond and change in Li⁺ ion concentration. The conductivity vs. composition curve exhibits two maxima which are interpreted in terms of the structural modification effect of Bi₂O₃ on LiBO₂ network and mixed-former effect, respectively. Results obtained from the XPS studies of the samples of composition x 0.005, have shown that the number of non-bridging oxygen atoms from B-O bond increases with the increase in Bi₂O₃ content. It has a maximum value at x = 0.003 where the conductivity has also exhibited a maximum value. Further increase of Bi₂O₃ content causes decrease in it. For higher Bi₂O₃ content (x * > 0.005), O 1s spectra of Bi₂O₃ has been separated out from that of Bi₂O₃. Bismuth ions have been substituted for boron ions as network former ions.     

Temperature dependence of the exafs spectrum in YBa2Cu3O7−δ compounds

The temperature dependence of the extended X-ray absorption fine structure (EXAFS) is studied in the high T_c superconductors, YBa₂Cu₃O_7−δ. The measurements were done at the Cu K-edge for samples of two orthorhombic phases (T_c≈90 K and ≈58 K, respectively) and a nonsuperconducting tetragonal phase. Interatomic distances and mean square relative displacements σ² for Cu-O bonds are determined by the least squares refinement. The results indicate that values of σ² increase near T_c for both the orthorhombic samples. It is concluded that this anomalous behavior related to T_c is caused by an anomalous vibration of oxygen atoms in the Ba-O layer. Changes in the Cu-O distances from 300 to 20 K are not found.     

Preparation and characterization of Y1−xPrxBa2Cu3O7−δ single crystals

We present a reliable method for growing single crystals of Y_1−xPr_xBa₂Cu₃O_7−δ high-T_c superconductors in ZrO₂ crucibles. This method results in crystals with greatly improved superconducting properties compared to crystals grown with the previously reported methods which use Al₂O₃ crucibles. We describe techniques for crystal growth in both Al₂O₃ and ZrO₂ crucibles using an excess of BaCo₃ and CuO as the flux. The crystals were characterized by means of DC magnetic-susceptibility measurements, electrical-resistivity measurements, and electron microprobe analysis. The effects of Al contamination on the conditions for crystal growth and on the superconducting properties of the crystals are found to be quite significant.     

Temperature dependence of the critical current in YBa2Cu3O7−δ and Bi2Sr2Ca1Cu2O8 Josephson junctions

We have studied the stationary Josephson effect on YBa₂Cu₃O_7−δ (T_c=90 K) and Bi₂Sr₂Ca₁Cu₂ O₈ (T_c=80 K and 87 K for two samples of different origin) ceramic based junctions. The temperature dependence of the critical current near T_c has been found as I_c≈(T_c-T) for the Y-Ba-Cu-O samples indicating that they should be classified as S-N-I-N-S type junctions. The I-V curves of the Bi-Sr-Ca-Cu samples show the typical behaviour of S-I-S structures. Using Ambegaokar-Baratoff's theory for Bi₂Sr₂Ca₁Cu₂O₈, the temperature dependence of the superconducting state gap Δ(T) was calculated and it was evaluated that 1.452Δ(0)/k_BT_c3.5.     

Ionic conductivity of crystalline and glassy Mg4.5Na7(P2O7)4

In our work single crystals of Mg_4.5Na₇(P₂O₇)₄ were prepared, pulverized, pressed into pellets and sintered in order to measure the electrical conductivity of polycrystalline specimens. The conductivity was also measured on glassy specimens obtained by the melting of previously prepared crystals. The electrical conductivities at 25°C with values of the order of 10⁻¹⁶ Ω⁻¹ cm⁻¹ for polycrystalline samples and a value of the order of 10⁻¹⁴ Ω⁻¹ cm⁻¹ for glass, show that the glassy phase of Mg_4.5Na₇(P₂ because of its greater molar volume and loosely packed structure, is a better matrix for ionic motion.     

Magnetic properties of xFe2O3(1−x)[B2O3 · PbO] glasses

The magnetic measurements performed on xFe₂O₃(1-x)[B₂O₃ · PbO] glasses show that for x 5 mol.% Fe₂O₃ the thermal variation of reciprocal susceptibility obeys a Curie behaviour. For higher iron content, at T 50 K, a nonlinear variation, typical for systems with random distribution of exchange interactions is observed. At greater temperatures than 50 K a Curie-Weiss behaviour is shown. The composition dependence of the Curie constants is analysed in correlation with the number of Fe³⁺ and Fe²⁺ ions as determined from Mössbauer effect measurements. A comparison with the data obtained in case of xFe₂O₃(1-x)[3B₂O₃ · PbO] glasses is made.     

Ionic conduction properties of layer-type oxides NaxMx/2Ti1−x/2O2 (M=Ni, Co; 0.60≤x≤1.0)

Layer-type oxide Na_xM_x/2^IITi_1−x/2^IVO₂ (M=Co, Ni; 0.60≤x≤1.0) has been prepared by solid state reactions. In both series, two structural variants of type -NaFeO₂ (O3) and β-RbScO₂ (P2) have been obtained consecutively as x decreases with a borderline composition around x_c0.7. With the decrease of x, the ionic conductivity has been found to increase up to 8.4×10⁻² S cm⁻¹ at 770 K (Na_0.67Co_0.33Ti_0.67O₂). Compositions of P2 have been found to exhibit the conductivity values two to five times greater than those of O3, primarily due to the larger rectangular threshold available for the diffusion of Na⁺ ions. Such a structural effect has also been considered to depend on the polarizability of alkali ion. HT-XRD and ²³Na-NMR data of Na_0.67Co_0.33Ti_0.67O₂ strongly suggest that the diffusion of Na⁺ ion is deeply related with the local distortion of trigonal prismatic sites, leading to the change of activation energy around 430 K.     

The nuclear contribution to the specific heat of single crystals of YBa2Cu3O7 and Bi2Sr2CaCu2O8

Specific heat data below 1 K of Bi₂Sr₂CaCu₂O₈ and YBa₂Cu₃O₇ are analyzed. For YBa₂Cu₃O₇ the nuclear specific heat, C_N, amounts to 38T⁻² μJ/mol K. C_N for Bi₂Sr₂CaCu₂O₈ exceeds that of YBa₂Cu₃O₇ by a factor of 15. The nuclear quadrupolar specific heat contribution alone is insufficient to explain the data for YBa₂Cu₃O₇, while lack of NQR data does not allow such a comparison in Bi₂Sr₂CaCu₂O₈ to be made. The contribution to C_N from nuclear spins coupled via the contact hyperfine interaction with correlated magnetic spins (in the CuO₂ plane) is derived as a function of the correlation length. This contribution can be treated independently from the quadrupolar term. We show that the excess specific heat in YBa₂Cu₃O₇ likely originates in a few percentage of an impurity (oxygen deficient) phase with a strong hyperfine field on the Cu nuclei.     

X-ray diffraction studies of epitaxy in orthorhombic- DyMnO3/Er1Ba2Cu3O7-δ thin film heterostructures on LaAlO3 (100) substrates

The heteroepitaxy in DyMnO₃/Er₁Ba₂Cu₃O_7-δ bilayer thin films on LaAlO₃ (100) substates was characterized by four-circle X-ray diffractometry. The Er₁Ba₂Cu₃O_7-δ thin films on LaAlO₃ (100) substrates were prepared by molecular-beam deposition (MBD) and post-growth annealing in wet and dry O₂ at 880°C, whereas the DyMnO₃ thin films on the Er₁Ba₂Cu₃O_7-δ/LaAlO₃ (100) heterostructure were deposited by MBD and post-growth annealing in dry O₂ at 750°C. The conventional X-ray diffraction (XRD) patterns as well as pole figures (φ-scans) for specific (hkl) reflections were acquired. The Er₁Ba₂Cu₃O_7-δ thin film in the DyMnO₃/Er₁Ba₂Cu₃O_7-δ/LaAlO₃ (100) heterostructure showed [001] oriented epitaxial growth, as expected. The DyMnO₃ thin film on the Er₁Ba₂Cu₃O_7-δ epilayer in the heterostructure grew with (110) epitaxy in its metastable orthorhombic phase (lattice constants: a_o=5.272 Å, b_o=5.795 Å and c_o=7.38 Å). The heteroepitaxial relationships at the orthorhombic-DyMnO O₃ (110) /Er₁Ba₂Cu₃O_7-δ (001) interface was determined as the following: DyMnO₃ (110) Er₁Ba₂Cu₃O_7-δ (001), DyMnO₃ [1 0] ¶r; Er₁Ba₂Cu₃O_7-δ[100] or Er₁Ba₂Cu₃O_7-δ[010], and DyMnO₃ [001] ¶r; Er₁Ba₂Cu₃O _7-δ[010] or Er₁Ba₂Cu₃O_7-δ [100].     

氧化铟/聚(3,4-乙烯二氧噻吩)复合材料的微结构及其热电性能研究

通过化学氧化合成的方法将纳米In_2O_3复合到聚(3,4-乙烯二氧噻吩)(PEDOT)中得到In_2O_3/PEDOT复合材料.利用X射线衍射、红外光谱、电子显微镜及正电子湮没等方法对复合材料的微观结构进行了系统研究,同时对材料的热学和电学性能进行了表征.结果表明,当In_2O_3的含量在22 wt%以下时,In_2O_3能很好地分散到PEDOT基体中.热电性能测试则显示In_2O_3/PEDOT复合材料的导电率随In_2O_3含量增加明显增大.纯PEDOT的电导率仅为7.5 S/m,而含12.3 wt%In_2O_3的复合材料的电导率达到25.75 S/m.该复合材料相应的功率因子(68.8×10~(-4)μW/m·K~2)相对于纯的PEDOT(14.5×10~(-4)μW/m·K~2)提高了近4倍.另外,复合材料的热导率相对于纯PEDOT也有所降低.最终复合材料的热电优值由0.015×10~(-4)提高到了0.073×10~(-4).结果表明,In_2O_3/PEDOT复合材料的热电性能相对于纯PEDOT的热电性能得到了比较明显的提高.     

Influence of fluctuations on thermal conductivity of high-Tc YBa2Cu3O7−δ superconductor

To study a behavior of the thermal conductivity near T_c specific heat and thermal diffusivity of the YBa₂Cu₃O_7−δ high-T_c ceramics were simultaneously measured. Close to T_c = 92.30 K the thermal diffusivity and the thermal conductivity discovered minima and the specific heat – maximum. Quantitative analysis of the influence of thermodynamical fluctuations showed the same power laws with Gaussian exponent equal to 0.5 and existing of crossover from the 3D Gaussian to 3D XY critical behavior in the specific heat and thermal conductivity at the approach to T_c. To explain the minimum in thermal conductivity at T_c we propose a mechanism of scattering of phonons on the superconducting fluctuations.     

(1-x)Sr_3Sn_2O_7+xCa_3Mn_2O_7陶瓷合成及其光电性能

为了寻求新的非常规多铁性材料,采用固相合成方法制备具有Ruddlesden-Popper结构的(1-x)Sr_3Sn_2O_7+x Ca_3Mn_2O_7(SSO+CMO)(x=0,0.05,0.10,0.15,0.20)系列陶瓷.通过X射线衍射、紫外可见光谱和磁性测量,发现SSO+CMO陶瓷为单一正交相结构,空间群为A21am.随着掺杂量x的增加,样品的晶胞参数和体积相应地减小;在室温不同频率下,样品的介电常数和介电损耗随着频率增加而减小,且在x=0.1时有弱的铁磁性.     

Realization and properties of ramp-type YBa2Cu3O7−δ/Au/Nb junctions

All-thin-film ramp type Josephson junctions between YBa₂Cu₃O_7−δ and Nb have been fabricated. This procedure allows connections between high-T_c and low-T_c superconductors at different crystal sides of the high-T_c superconductor on one chip, which is of great interest for novel phase devices. A thin Au layer is incorporated as a chemical barrier to avoid oxygen transfer from the YBa₂Cu₃O_7−δ to the Nb. Critical current densities up to 600 A/cm² are obtained at T=4.2 K, with typical R_nA values of 0.8 μΩ cm². The variation of the magnetic field dependence of the critical current with the angle between the junction barrier and the YBa₂Cu₃O_7−δ crystal axes is explained by considering a predominant d_x²−y² order parameter symmetry of the YBa₂Cu₃O_7−δ. The successful fabrication of these junctions allows the implementation of novel superconducting electronics, such as complementary Josephson circuitry or proposed qubit concepts, using the unconventional order parameter symmetry of the high-T_c superconductor.     

Thermodynamic properties of the clathrate-type silver-oxide Ag6O8AgHF2

We report normal-state and superconducting properties of the clathrate-type silver-oxide Ag₆O₈AgHF₂. We present electrical resistivity, DC- and AC-susceptibility and specific-heat measurements of single crystalline Ag₆O₈AgHF₂. In the normal state, Ag₆O₈AgHF₂ exhibits metallic conductivity and a phase transition near 110 K, possibly a structural phase transition as observed in the related compound Ag₆O₈AgNO₃. The onset of superconductivity of our samples is observed around 1.2–1.5 K, and the H–T phase diagram is determined for the first time. The upper critical field H_c2(0) is estimated to be about 2000–2200 Oe and the coherence length ξ_GL(0) to be 40 nm.     

A new family of magnetoelectric materials: A2M4O9(A = Ta, Nb; M = Mn, Co)

The existence of the magnetoelectric (ME) effect in the transition metal niobates and tantalates A₂M₄O₉(A = Ta, Nb; M = Mn, Co) has been confirmed by the observation of the electrically induced magnetic moment in these materials. Both parallel and prependicular ME susceptibilities were measured as a function of temperature in powder specimens. The transition temperatures were found to be 110 ±1 (Nb₂Mn₄O₉), 103 ±1 (Ta₂Mn₄O₉), 27.0 ±0.5 (Nb₂Co₄O₉), and 20.6 ±0.5°K (Ta₂Co₄O₉) from the ME measurements.     

Systematic thermopower measurements of the thallium cuprates Tl(Ba,Sr)2Cam−1CumO2m+3−δ and Tl2Ba2Cam−1CumO2m+4+δ

The thermoelectric power (TEP) S versus temperature has been systematically investigated for several series of the superconducting cuprates Tl(Ba,Sr)₂Ca_m−1Cu_mO_2m+3−δ (m = 2, 3) and Tl₂Ba₂Ca_m−1Cu_mO_2m+4+δ (m = 1, 2, 3). The consideration of the S(T_c) curves allows two important points to be found evidence for. The first one deals with the fact that all these superconducting thallium cuprates are systematically overdoped whatever T_c, and whatever the number of Cu or Tl layers; no underdoped superconducting cuprate could be obtained. The second point shows that there exist two classes of Tl cuprates: the weakly overdoped cuprates that exhibit a T_{c max} ≥ 100 K (all the triple copper layer cuprates and the 2212 cuprates) and those which can be heavily doped that exhibit a T_{c max} ≤ 90 K (the 2201 and the 1212 cuprates). The different behavior of thallium cuprates compared to YBa₂Cu₃O_7−δ and to bismuth cuprates is discussed.     

The relationship between crystal structure and electrical conductivity in the LaY1−xInxO3 (x=0.0–0.7) system

The electrical conductivity of the LaY_1−xIn_xO₃ (x=0.0–0.7) system has been studied from the viewpoint of crystal chemistry. The high temperature form of LaYO₃ (x=0.0) was ascertained to be the Sm₂O₃-type (B-type rare earth) structure, not perovskite-type one. The X-ray diffraction (XRD) experiments revealed that the samples with x=0.05 and 0.10 were the mixed phase of Sm₂O₃-type and perovskite-type structure, and changed to perovskite phase in the range of x0.20. From oxygen partial pressure dependence of the electrical conductivity, it was found that both the Sm₂O₃-type and the perovskite-type single phases showed hole conduction, but the mixed phase did oxide-ion one. The electrical conductivity of the LaY_1−xIn_xO₃ (x=0.0–0.7) system increased with increasing x, and showed the maximum value in the range of x=0.05–0.10, and then decreased with increasing x. The occurrence of oxide-ion conduction was discussed from the viewpoint of lattice distortion in the mixed phase.     

Oxygen permeability of La2Cu(Co)O4+δ solid solutions

Formation of the La₂Cu_1−xCo_xO_4+δ solid solutions with orthorhombic K₂NiF₄-type structure was found to be in the range of 0≤x≤0.30 at temperatures above 1270 K. Incorporating cobalt into the copper sublattice of lanthanum cuprate leads to increasing oxygen hyperstoichiometry and decreasing electrical conductivity. Thermal expansion coefficients of the La₂Cu_1−xCo_xO_4+δ (x=0.02–0.30) ceramics at 470–1100 K were calculated from the dilatometric data to vary in the range (12.2–13.2)×10⁻⁶ K⁻¹. Studying the dependence of oxygen permeation fluxes through La₂Cu(Co)O_4+δ on the membrane thickness demonstrated that the oxygen transport at the thickness values below 1 mm is limited by both surface exchange rate and bulk ionic conductivity. Oxygen permeability of the La₂Cu_1−xCo_xO_4+δ solid solutions was ascertained to increase with cobalt concentration at x=0.02–0.10 and to decrease with further dopant additions, indicating a participation of interstitial oxygen in the ionic transport.     

Study of the interfacial structure and chemistry of CVD κ-Al2O3/TiC multilayer coatings

This article describes the interfacial regions in CVD grown TiC/κ-Al₂O₃ multilayers. A number of microanalytical techniques were used including HREM, EDX and EELS. Occasionally, the first 50 nm of the alumina layers deposited on the intermediate TiC layers grew as a cubic alumina, heavily faulted, containing small amounts of sulphur (S), maybe as a stabiliser. The presence of slightly rounded TiC (111) facets may act as preferred nucleation sites for the cubic Al₂O₃ phase, with a ‘cube on cube’ orientation relationship. In this way the nucleation of κ-Al₂O₃ is less favourable. After some tens of nanometres the cubic phase cannot be stabilised any longer and the layer continues to grow as κ-Al₂O₃. A number of observations point towards the reaction zone (RZ) being η- and/or γ-Al₂O₃. The diffraction work and the FFT analysis of the HREM images show that the RZ is an fcc phase with a=7.9 Å, which matches with η- and γ-Al₂O₃. The EELS Al fine structure indicate more tetrahedral Al ions than in κ-Al₂O₃, as in η- and γ-Al₂O₃. The RZ contains small amounts of S, as has been reported for γ-Al₂O₃. Due to the structural similarities between η- and γ-Al₂O₃ it was not possible to determine which of these cubic phases is present in the RZ.     

RE2Ti2O7(RE=Gd,Y,Ho,Er)的结构、机械性能及热学性质的第一性原理研究(英文)

本文利用第一性原理和准谐近似的方法研究了一系列钛酸盐烧绿石,即RE₂Ti₂O₇（RE=Gd,Y,Ho,Er）的结构、机械性能及热学性质。研究结果表明,在基态下RE₂Ti₂O₇具有良好的抗压、抗剪切能力。并且,由于这些化合物的齐纳指数接近于1,可近似地看作各向同性材料。此外,计算得到的热膨胀系数在高温区与实验值符合得较好。在500~1 500 K温度区间内,平均热膨胀系数为（10.4~13.1）×10-6 K-1。基于Slack模型,我们还计算了这些材料的晶格热导率,当温度等于1 000 K时,这四种物质的热导率在区间（1.5~4.9）W·m-1·K-1内。