温度及pH敏感聚(丙烯酸)/聚(N-异丙基丙烯酰胺)互穿聚合物网络水凝胶的合成及性能研究

合成聚（丙烯酸）／聚（Ｎ 异丙基丙烯酰胺）互穿聚合物网络（ＰＡＡｃ／ＰＮＩＰＡＩＰＮ）水凝胶，具有温度及ｐＨ双重敏感特性．这种水凝胶在弱碱性条件下的溶胀率远大于酸性条件下的溶胀率．在酸性条件下，随着温度上升，凝胶的溶胀率也随之逐渐上升；而在弱碱性条件下，温度低于聚（Ｎ 异丙基丙烯酰胺）（ＰＮＩＰＡ）的较低临界溶解温度（ＬＣＳＴ）时，溶胀率也随着温度的上升而上升，当温度达到ＬＣＳＴ时，凝胶的溶胀率突然急剧下降，并随着温度的逐渐上升而下降．     

Preparation and characterization of a novel IPN hydrogel memberane of poly(N-isopropylacrylamide)/carboxymethyl chitosan (PNIPAAM/CMCS)

A novel type of interpenetrating polymer networks (IPN) hydrogel membrane of poly(N-isopropylacrylamide)/carboxymethyl chitosan (PNIPAAm)/(CMCS) was prepared, and the effects of the feed ratio of components, swelling medium and irradiation dose on the swelling and deswelling properties of the hydrogel was systematically studied. The results showed that the introduction of CMCS did not shift the LCST (at 32 °C), which is similar to the pure PNIPAAm. The lowest swelling ratio was at pH 2. There was little influence of irradiation dose on the thermo- and pH-sensitivity of the IPN hydrogel, increasing dose only decreased the swelling ratio. The PNIPAAm:CMCS=1:4 w/w hydrogel was not thermo-sensitive in distilled water, whereas it showed a discontinuous volume phase transition in pH 2 and a continuous one in pH 8 buffer. Consequently, a combination of pH and temperature can be coupled to control the responsive behavior of these hydrogels.     

Porous alginate-Ca hydrogels interpenetrated with PNIPAAm networks: Interrelationship between compressive stress and pore morphology

Thermo-sensitive porous hydrogels composed of interpenetrated networks (IPN) of alginate-Ca²⁺ and PNIPAAm have been obtained. The hydrogels were prepared by cross-linking alginate-Na⁺ with Ca²⁺ ions inside PNIPAAm networks. Compressive tests and scanning electron microscopy were used to evaluate gel strength and pore morphology, respectively. IPN hydrogels displayed two distinct pore morphologies under thermal stimuli. Below 30-35 °C, the LCST of PNIPAAm in water, IPN hydrogels were highly porous. The pore size of hydrogel heated above LCST became progressively smaller. Alginate-Ca²⁺ and PNIPAAm hydrogels, used as references, did not present such behaviour, indicating that the porous effect is due to IPN hydrogel. It was verified that higher strength is achieved when the hydrogel presents small pore size and the temperature is increased. It is suggested that at temperatures above LCST, the PNIPAAm chains shrink and pull the alginate-Ca²⁺ networks back. During shrinking, the polymer chains occupy the open spaces (pores from which water is expelled), and therefore, the hydrogel becomes less deformable when subjected to compressive stress. The results presented in this work indicate that the mechanical properties as well as the pore morphologies of these IPN hydrogels can be tailored by thermal stimulus.     

新型钴酞菁接枝温敏聚合物的制备及性能

采用2,4,6-三氯-1,3,5-三嗪对四氨基钴酞菁进行改性,并以共价键接枝到聚N-异丙基丙烯酰胺上制得一种新型温敏性高分子催化剂——钴酞菁接枝温敏聚合物,并采用UV-Vis、TG等对其进行表征.对钴酞菁接枝温敏聚合物、温敏聚合物和小分子金属酞菁进行溶解性测试,结果表明与四氨基钴酞菁相比,所合成的钴酞菁接枝温敏聚合物能溶解于水和大多数有机溶剂,且该聚合物水溶液具有良好的温敏性,其最低临界溶解温度(LCST)为34.5℃.采用浊度法考察了不同比例的混合溶剂(乙醇/水、DMF/水)对LCST的影响,结果表明随着有机溶剂含量的增加,LCST先下降后升高,而当有机溶剂增加到一定程度时温敏性消失.本文还考察了钴酞菁接枝温敏聚合物对2-巯基乙醇的催化活性,结果表明随着温度升高,催化活性也不断提高,而当温度超过LCST时催化活性急剧下降,聚合物从溶液中析出.基于这些特性,该温敏聚合物负载酞菁作为一种新型的催化剂可实现均相催化、异相分离.     

The Research of Biomedical Intelligent Polymer Materials

The properties of biomedical intelligent polymer materials can be changed obviously when there is a little physical or chemical change caused by external condition. They are in the forms of solids, solutions and the polymers on the surface of carrier, and include water solution of hydrophilic polymers, cross-linking hydrophilic polymers(i.e. hydrogels) and the polymers on the surface of carrier. The environmental stimulating factors are temperature, pH value, composition of solution, ionic intention, light intention, electric field, stress field and magnetic field etc.. The properties of intelligent polymer are those of phase, photics, mechanics, electric field, surface energy,reaction ratio, penetrating ratio and recognition etc..Stimulation-response of intelligent water-soluble polymerWater-soluble intelligent polymer can be separated out from solution under special external condition. It can be used as the switch of temperature or pH indicator. When water-soluble intelligent polymer is mixed with soluble-enzyme matter or cell suspension, the polymer can bring phase separation and react with soluble-enzyme matter or cell membrane through accepting some external stimulation. Other water-soluble intelligent polymer is that can make the main chemical group of some natural biomolecular recognition sequence section to arrange on skeleton of polymer at random. It is the same ratio as natural biomolecules.Stimulation-response of intelligent polymer of carrier surface Intelligent polymer can be fixed on the surface of solid polymer carrier through chemical grafting or physical adsorption. When the external conditions are changed, the thickness, humidity and electric field of the surface layer will be changed. Intelligent polymer can be preparated the permanence switch by precipitating into the hole of porous surface, and it can control on-off state of the hole. When protein or cell interacts with intelligent polymer surface to be placed in to open or close, they can be selectively absorbed on hydrophobic surface.Stimulation-response of intelligent polymer hydrogelIntelligent polymer hydrogel's construction, physical property, and chemical property can change with the changing of external environmental conditions. When environmental stimulation signal, for example, solution composition, pH value, ionic intention, temperature, light intention, electric field,magnetic field and substance etc. changes, the intelligent polymer will occur to break of volume.This is the intelligence of polymer hydrogel.The intelligence of these polymers will be widely applied in biomedical fields.     

DTPA-PNIPAAm的合成及热敏性研究

热敏水溶性高分子聚(N-异丙基丙烯酰胺)(PNIPAAm)在水溶液中有最低临界溶液温度(LCST).当温度在LCST附近发生变化时,PNIPAAm可发生逆相转变.基于该特性,可通过PNIPAAm将放射性治疗核素运输到病变组织通过射线杀灭病变细胞.通过4,4′-偶氮二(氰戊酸)、乙二胺、二乙三胺五乙酸酐(DTPAA)、N-异丙基丙烯酰胺合成了带DTPA端基的PNIPAAm,合成的DTPA-PNIPAAm保持了与PNIPAAm相似的LCST.本文的工作为PNIPAAm运输金属治疗核素奠定了基础.     

聚丙烯酰胺/聚异丙基丙烯酰胺互穿网络水凝胶的制备与性能

采用分步法用电子加速器辐射合成了聚丙烯酰胺(PAAm)/聚异丙基丙烯酰胺(PNIPAAm)互穿网络水凝胶,并考察了温度、pH值、离子强度对其溶胀性能的影响.研究表明:互穿水凝胶具有温度敏感性,且其体积相变与互穿网络中PAAm和PNIPAAm含量有关,随着网络中PAAm含量的增加水凝胶的体积相变趋于平缓,可以通过改变PAAm和PNIPAAm的组成比来控制水凝胶的体积相变行为.此外,互穿水凝胶还具有pH敏感性和一定的抗盐性.     

Synthesis and properties of thermoresponsive magnetic polymer composites and their electrospun nanofibers

The thermoresponsive magnetic polymer composites and nanofibers were fabricated. Their thermal and magnetic properties were also investigated. Fe₃O₄ nanoparticles were prepared by coprecipitation method. Further condensation reaction was used to fabricate the double‐layer lauric acid modified Fe₃O₄ (DLF) nanoparticles dispersed well in water. Thermal properties of poly(N‐isopropylacrylamide) (PNIPAAm) and DLF/PNIPAAm composites and their aqueous solutions were measured by TGA and DSC. With the increasing of DLF content, the interaction between DLF and PNIPAAm caused the lower critical solution temperature (LCST) of polymer solution to shift from 33 to 31.25 °C. The effects of concentration and pH on LCST were also studied. The DLF/PNIPAAm nanofibers were fabricated by electrospinning. Their diameters were around 100–250 nm. Magnetization curves of DLF/PNIPAAm composite and nanofibers were overlapped and the saturated magnetizations were the same. Magnetic attraction behaviors of DLF/PNIPAAm polymer solution at temperatures below and above LCST were different. Aggregation of DLF/PNIPAAm above LCST enhanced magnetic moment density as well as magnetic attraction ability. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 848–856     

Temperature-controlled flow switching in nanocapillary array membranes mediated by poly(N-isopropylacrylamide) polymer brushes grafted by atom transfer radical polymerization

We report actively controlled transport that is thermally switchable and size-selective in a nanocapillary array membrane (NCAM) prepared by grafting poly(N-isopropylacrylamide) (PNIPAAm) brushes onto the exterior surface of a Au-coated polycarbonate track-etched membrane. A smooth Au layer on the membrane surface, which is key to obtaining a uniform polymer film, was prepared by thermal evaporation of approximately 50 nm Au on both exterior surfaces. After evaporation, the inner diameter of the pore is reduced slightly, but the NCAM retains a narrow pore size distribution. PNIPPAm brushes with 10-30 nm (dry film) thickness were grafted onto the Au surface through surface-initiated atom transfer radical polymerization (ATRP) using a disulfide initiator, (BrC(CH3)2COO(CH2)11S)2. Molecular transport through the PNIPAAm polymer brush-modified NCAMs was investigated by real-time fluorescence measurements using fluorescein isothiocyanate (FITC)-labeled dextrans ranging from 4.4 to 282 kDa in membranes with variable initial pore diameters (80, 100, and 200 nm) and different PNIPAAm thicknesses. Manipulating the temperature of the NCAM through the PNIPAAm lower critical solution temperature (LCST) causes large, size-dependent changes in the transport rates. Over specific ranges of probe size, transport is completely blocked below the LCST but strongly allowed above the LCST. The combination of the highly uniform PNIPAAm brush and the monodisperse pore size distribution is critical in producing highly reproducible switching behavior. Furthermore, the reversible nature of the switching raises the possibility of using them as actively controlled filtration devices.     

Thermosensitive polylactide‐glycolide delivery systems for treatment of narcotic addictions

Environmental switches may be fabricated for the controlled release of pharmaceutical drug using a thermally responsive polymer with the intrinsic chemical and physical nature of stimuli‐sensitive smart materials. Particularly, much attention has been paid to the biomedical applications of poly(N‐isopropyl acrylamide) (PNIPAAm) because of its unique reversible transition at a specific lower critical solution temperature (LCST).Thermally sensitive block copolymers, poly(N‐isopropyl acrylamide‐b‐poly(L ‐lactide‐co‐glycolide) (PNIPAAm‐b‐PLGA), and polyethylene glycol‐poly (lactide‐co‐glycolide) (PEG‐PLGA) triblock copolymers with different compositions and length of PLGA block were synthesized via ring‐opening polymerization of lactide and glycolide in the presence of OH‐terminated PNIPAAm or PEG. The composition and structure of the polymer were determined by NMR and FTIR. The effect of important factors, such as ionic strength, pH, and polymer concentration on the phase transition behavior of temperature‐sensitive polymers, were investigated by cloud point measurements. The resulting thermosensitive polymers were used for the entrapment of a narcotic antagonist drug, naltrexone, as the model drug. The loading efficiency and drug release behavior of naltrexone‐loaded hydrogels were investigated. The naltrexone loaded thermosensitive polymers were able to sustain the release of naltrexone for different periods of time, depending on the polymer composition, and concentration. In vitro release studies showed that these thermosensitive polymers are able to deliver naltrexone in biologically active forms at a controlled rate for 3–8 weeks. Copyright © 2009 John Wiley & Sons, Ltd.     

Thermally Responsive Hydrogel Blends: A General Drug Carrier Model for Controlled Drug Release

Thermally responsive hydrogels have drawn significant research attention recently because of their simple use as drug carrier at human body temperature. Here we design a hybrid hydrogel that incorporates a hydrophilic polymer, polyethyleneimine (PEI), into the thermally responsive hydrogel poly(N‐isopropylacrylamide) (PNIPAm), as a general drug carrier model for controlled drug release. In this work, on one hand, PEI modifies the structure and the size of the pores in the PNIPAm hydrogel. On the other hand, PEI plays an important role in tuning the water content in the hydrogel and controls the water release rate of the hydrogel below the lower critical solution temperature (LCST), resulting in a tunable release rate of the drugs at human body temperature (37 °C). Different release rates are shown as different amounts of PEI are incorporated. PEI controls the release rate, dependent on the charge characteristics of the drugs. The hydrogel blends described in this work extend the concept of a general drug carrier for loading both positively and negatively charged drugs, as well as the controlled release effect.     

温度及pH敏感性水凝胶的合成及性能研究

乙烯基吡咯烷酮与丙烯酸共聚物／聚丙烯酸β-羟基丙酯互穿网络水凝胶具有温度及PH双重敏感特性。经验证,在蒸馏水中,聚丙烯酸β－羟基丙酯与丙烯酸间存在络合作用,在缓溶液中,没有这样络合作用。     

Radiation synthesis of poly[(dimethylaminoethyl methacrylate)-co-(diallyl dimethyl ammonium chloride)] hydrogels and its application as a carrier for notoginsenoside delivery

Novel pH/temperature sensitive hydrogel was synthesized by radiation induced copolymerization and cross-linking of dimethylaminoethyl methacrylate (DMAEMA) and diallyldimethyl ammonium chloride (DADMAC). Reactivity ratio of DADMAC (r₁) and DMAEMA (r₂) was determined as 1.02 and 0.98, which means that poly(DMAEMA-co-DADMAC) is an azeotropic copolymer. Content of DADMAC, i.e., charge density of the hydrogel was found to influence their properties significantly. Compared with polyDMAEMA hydrogel, poly(DMAEMA-co-DADMAC) showed enhanced equilibrium degree of swelling (EDS). Low critical solution temperature (LCST) of the hydrogel increased with the charged density. Content of DADMAC had no effect on the pH dependence of the final gel. Aiming at its application as a carrier for Chinese herb extract delivery system, the embedment and pH/temperature dependence of controlled release were investigated using notoginsenoside as a model drug. The maximum embedment amount of notoginsenoside was obtained in a gel containing 3 mol.% DADMAC. The temperature dependence and pH dependence of notoginsenoside release followed the same trend as that of EDS, for instance, higher ratio of notoginsenoside release occurred at 25 °C and pH 1.7, at which higher EDS was obtained. By these means, the release of notoginsenoside can be controlled by adjusting the pH, ionic strength, temperature of solution as well as the composition and structure of the gel.     

A simple FTIR spectroscopic method for the determination of the lower critical solution temperature of N‐isopropylacrylamide copolymers and related hydrogels

Linear and crosslinked polymers based on N‐isopropylacrylamide (NIPAAm) exhibit unusual thermal properties. Aqueous solutions of poly(N‐isopropylacrylamide) (PNIPAAm) phase‐separate upon heating above a lower critical solution temperature (LCST), whereas related hydrogels undergo a swelling–shrinking transition at an LCST. A linear copolymer made of NIPAAm/acryloxysuccinimide (98/2 mol/mol) and two hydrogels with different hydrophilicities were prepared. Fourier transform infrared (FTIR) spectroscopy was employed to determine the transition temperature and provide insights into the molecular details of the transition via probing of characteristic bands as a function of temperature. The FTIR spectroscopy method described here allowed the determination of the transition temperature for both the linear and crosslinked polymers. The transition temperatures for PNIPAAm and the gel resulting from the crosslinking with polylysine or N,N′‐methylenebisacrylamide (MBA) were in the same range, 30–35 °C. For the gels, the transition temperature increased with the hydrophilicity of the polymer matrix. The spectral changes observed at the LCST were similar for the free chains and the hydrogels, implying a similar molecular reorganization during the transition. The C H stretching region suggests that the N‐isopropyl groups and the backbone both underwent conformational changes and became more ordered upon heating above the LCST. An analysis of the amide I band suggests that the amide groups of the linear polymer were mainly involved in hydrogen bonding with water molecules below the LCST, the chain being flexible and disordered in a water solution. During the transition, around 20% of these intermolecular hydrogen bonds between the polymer and water were broken and replaced by intramolecular hydrogen bonds. Similar changes were also observed at the LCST of a gel crosslinked with MBA. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 907–915, 2000     

NIPAAm系互穿网络凝胶的合成及载药释药性能研究

合成了三种亲疏水性不同的温度及pH敏感的PAAc／P（NIPAAm-co-BMA）、PAAc／PNIPAAm和PAAc／P（NIPAAm-co-AAm）互穿网络（IPN）水凝胶,以水杨酸钠和水杨酸为模型药物,研究了温度、pH值及药物和凝胶的亲疏水性相互作用对模型药物释药性能的影响。研究结果表明,随着凝胶亲水性的增强,水杨酸钠的载药率提高,释药率也越大;相反疏水性增强也有利于提高水杨酸的载药率;IPN凝胶在水中的释药过程属于溶胀支配型释放,药物释放率随凝胶的亲水性增强而增强,同时,载药凝胶在45℃水中的释药率大于25℃时的释药率。在25℃时,水杨酸在pH=2．2的缓冲溶液中几乎不释放,而在pH=7．4的缓冲溶液中能以较快的速率释放。     

Fast synthesis of temperature-sensitive PNIPAAm hydrogels by microwave irradiation

A novel method, microwave irradiation synthesis, is proposed for the preparation of thermo-sensitive poly(N-isopropylacrylamide) (PNIPAAm) hydrogels. The PNIPAAm hydrogels were separately synthesized by using microwave irradiation method and water-bath heating method. Chemical groups, lower critical solution temperature (LCST) and surface morphology of these PNIPAAm hydrogels were characterized by FT-IR, DSC and SEM. Swelling ratios of the gels were measured gravimetrically in the temperature range from 10.0 to 60.0 °C. Results showed that (1) the use of microwave irradiation can greatly shorten the reaction time required for PNIPAAm hydrogel synthesis from several hours to several minutes in comparison with water-bath heating method, and obviously improve the yields of the PNIPAAm gels, which were up to 99% after a short reaction time; (2) SEM micrographs and textural measurement revealed that the gels synthesized using microwave irradiation had more porous structure, and their average pore sizes and specific surface areas were larger than those of the gels synthesized using water-bath heating method; and (3) the PNIPAAm hydrogels synthesized using microwave irradiation had much higher swelling ratios at 10.0 °C below the LCST, and had lower swelling ratio at 60.0 °C above the LCST compared to the hydrogels synthesized by water-bath method.     

温度及pH敏感性共聚物水凝胶的合成及其对辅酶A的控制释放

以N-乙烯基吡咯烷酮(NVP)和甲基丙烯酸-N,N-二甲胺乙酯(DMAEMA)为单体,采用自由基聚合法合成了NVP与DMAEMA的共聚物及其水凝胶。研究发现共聚物的水溶液具有温度及pH双重敏感特性。相分离温度随DMAEMA含量的增加和水溶液浓度的降低而升高,随pH值的增大而减小且相变敏锐。通过对水凝胶溶胀率的考察,发现共聚凝胶在适当的单体浓度及交联剂浓度下,有较敏感的溶胀-退胀行为。在碱性条件下,共聚凝胶随温度的升高迅速退胀。pH=9时,改变温度,对辅酶A有很好的控制释放;而在酸性条件下,则无退胀行为,对辅酶A不能释放。     

Three-dimensional porous HPMA-co-DMAEM hydrogels for biomedical application

The aim of this work is to develop a novel biocompatible drug delivery carrier and tissue engineering scaffold with the ability of controlled drug release and also tissue regeneration. We have synthesized N-(2-hydroxypropyl)methacrylamide and 2-(dimethylamino)ethyl methacrylate copolymer-based hydrogels loaded with doxorubicin and tested in vitro. The manifestation of temperature sensitivity is noted with a sharp decrease or increase in hydrogel optical transparency that happens with the temperature exceeding a critical transition value. The drug release profile exhibited pH-sensitive behavior of the hydrogel. The hydrolytic degradation of gel and in vitro studies of polymer–doxorubicin conjugate and doxorubicin release from hydrogel matrix indicated that hydrogels were stable under acidic conditions (in buffers at pH 4.64 and 6.65). In both drug forms, polymer–doxorubicin conjugate and free doxorubicin could be released from the hydrogel scaffold at a rate depending directly on either the rate of drug diffusion from the hydrogel or rate of hydrogel degradation or at rate controlled by a combination of the both processes. In vitro analysis showed homogenous cell attachment and proliferation on synthesized hydrogel matrix. In vivo implantation demonstrated integration of the gel with the surrounding tissue of mice within 2 weeks and prominent neo-angiogenesis observed in the following weeks. This multifunctional hydrogels can easily overcome biological hurdles in the in vivo conditions where the pH range changes drastically and could attain higher site-specific drug delivery improving the efficacy of the treatment in various therapeutical applications, especially in cancer therapy, and could also be used as tissue engineering scaffold due to its porous interconnected and biocompatible behavior.     

Dual magnetic-/temperature-responsive nanoparticles for microfluidic separations and assays

A stimuli-responsive magnetic nanoparticle system for diagnostic target capture and concentration has been developed for microfluidic lab card settings. Telechelic poly(N-isopropylacrylamide) (PNIPAAm) polymer chains were synthesized with dodecyl tails at one end and a reactive carboxylate at the opposite end by the reversible addition fragmentation transfer technique. These PNIPAAm chains self-associate into nanoscale micelles that were used as dimensional confinements to synthesize the magnetic nanoparticles. The resulting superparamagnetic nanoparticles exhibit a gamma-Fe2O3 core ( approximately 5 nm) with a layer of carboxylate-terminated PNIPAAm chains as a corona on the surface. The carboxylate group was used to functionalize the magnetic nanoparticles with biotin and subsequently with streptavidin. The functionalized magnetic nanoparticles can be reversibly aggregated in solution as the temperature is cycled through the PNIPAAm lower critical solution temperature (LCST). While the magnetophoretic mobility of the individual nanoparticles below the LCST is negligible, the aggregates formed above the LCST are large enough to respond to an applied magnetic field. The magnetic nanoparticles can associate with biotinylated targets as individual particles, and then subsequent application of a combined temperature increase and magnetic field can be used to magnetically separate the aggregated particles onto the poly(ethylene glycol)-modified polydimethylsiloxane channel walls of a microfluidic device. When the magnetic field is turned off and the temperature is reversed, the captured aggregates redisperse into the channel flow stream for further downstream processing. The dual magnetic- and temperature-responsive nanoparticles can thus be used as soluble reagents to capture diagnostic targets at a controlled time point and channel position. They can then be isolated and released after the nanoparticles have captured target molecules, overcoming the problem of low magnetophoretic mobility of the individual particle while retaining the advantages of a high surface to volume ratio and faster diffusive properties during target capture.     

Ultrafine hydrogel fibers with dual temperature‐ and pH‐responsive swelling behaviors

Ultrafine hydrogel fibers that were responsive to both temperature and pH signals were prepared through the electrospinning of poly(N‐isopropylacrylamide) (PNIPAAm) and poly(acrylic acid) mixtures in dimethylformamide. Both the diameters (700 nm to 1.2 μm) and packing of the fibers could be controlled through changes in the polymer compositions and PNIPAAm molecular weights. These fibers were rendered water‐insoluble by the addition of either Na₂HPO₄ or poly(vinyl alcohol) (PVA) to the solution, followed by the heat curing of the fibers. The fibers crosslinked with Na₂HPO₄ swelled to 30–120 times in water; this was significantly higher than the swelling of those crosslinked with PVA. The PVA‐crosslinked hydrogel fibers, however, exhibited faster swelling kinetics; that is, they reached equilibrium swelling in less than 5 min at 25 °C. They were also more stable after 1 week of water exposure; that is, they lost less mass and retained their fibrous form better. All the hydrogel fibers showed a drastic increase in the swelling between pH 4 and 5. The PVA‐crosslinked hydrogel fibers exhibited distinct temperature‐responsive phase‐transition behavior of PNIPAAm, whereas the Na₂HPO₄‐crosslinked hydrogel fibers showed altered two‐stage phase transitions that reflected side‐chain modification of PNIPAAm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6331–6339, 2004