Ultrathin films of functionalised single-walled carbon nanotubes: a potential bio-sensing platform

ABSTRACT

The Langmuir monolayer is a special class of lyotropic liquid crystalline system wherein phase transition essentially depends on surface density, temperature and ion-content in the aqueous medium. The variety of surface phases can be transferred onto devices by the Langmuir–Blodgett (LB) technique. The Langmuir monolayer of pristine single-walled carbon nanotubes (SWCNTs) exhibited gas and liquid-like phases. The LB film of SWCNTs shows target surface pressure dependent interesting morphologies. The methane gas sensing using parallel alignment of SWCNTs was found to be better than that of randomly oriented SWCNTs. The SWCNTs can be functionalised chemically to enhance the ease of film processability and affinity towards analytes. These are essential parameters for the development of a sensor. In this article, we present our work on Langmuir monolayer and LB films of octadecylamine functionalised SWCNTs (ODACNTs) and its sensing application towards bio-analytes, e.g. L-aspartic acid and bovine serum albumin. The sensing performance of LB film of ODACNTs was compared with that of spin-coated films of ODACNTs. The sensing performance of LB films of ODACNTs indicated a potential platform for bio-sensing application.     

Raman spectroscopy of individual single-walled carbon nanotubes from various sources

Resonance Raman spectroscopy/microscopy was used to study individualized single-walled carbon nanotubes (SWNTs) both in aqueous suspensions as well as after spin-coating onto Si/SiO2 surfaces. Four different SWNT materials containing nanotubes with diameters ranging from 0.7 to 1.6 nm were used. Comparison with Raman data obtained for suspensions shows that the surface does not dramatically affect the electronic properties of the deposited tubes. Raman features observed for deposited SWNTs are similar to what was measured for nanotubes directly fabricated on surfaces using chemical vapor deposition (CVD) methods. In particular, individual semiconducting tubes could be distinguished from metallic tubes by their different G-mode line shapes. It could also be shown that the high-power, short-time sonication used to generate individualized SWNT suspensions does not induce defects in great quantities. However, (additional) defects can be generated by laser irradiation of deposited SWNTs in air, thus giving rise to an increase of the D-mode intensity for even quite low power densities (approximately 10(4) W/cm2).     

Preparation and characterization of individual peptide-wrapped single-walled carbon nanotubes

Two challenges for effectively exploiting the remarkable properties of single-walled carbon nanotubes (SWNTs) are the isolation of intact individual nanotubes from the raw material and the assembly of these isolated SWNTs into useful structures. In this study, we present atomic force microscopy (AFM) evidence that we can isolate individual peptide-wrapped SWNTs, possibly connected end-to-end into long fibrillar structures, using an amphiphilic alpha-helical peptide, termed nano-1. Transmission electron microscopy (TEM) and well-resolved absorption spectral features further corroborate nano-1's ability to debundle SWNTs in aqueous solution. Peptide-assisted assembly of SWNT structures, specifically in the form of Y-, X-, and intraloop junctions, was observed in the AFM and TEM images.     

Dispersions of individual single-walled carbon nanotubes of high length

In summary, we have presented a suitable approach to obtain surfactant-stabilized suspensions of long, individually dispersed SWCNTs essentially free of bundles. The combination of mild tip and bath ultrasonication has proven effective in unbundling the SWCNT ropes and, at the same time, in minimizing tube shortening. This method is expected to be useful for applications that critically depend on the availability of bulk dispersions of long, individual tubes with minimized defect densities, such as for nanotube-based electronics and composite materials. Furthermore, the observed purification-induced changes in the electronic structure of HiPco SWCNTs indicate that care has to be taken when comparing their properties with those of the as-produced material.     

Ultrathin transparent conductive films of polymer-modified multiwalled carbon nanotubes

Deposition of multiwalled carbon nanotubes modified by poly(2-vinylpyridine) (CNT-g-P2VP) from aqueous dispersions at low pH is an effective method to prepare homogeneous ultrathin films with a tunable CNTs density. A percolation threshold of 0.25 mug/cm2 and a critical exponent alpha = 1.24 have been found from dc conductivity measurements. The sheet resistance value agrees with the percolation theory for 2D films. According to AFM and electrical measurements, even when only 5% of the surface is covered by CNT-g-P2VPs, the sheet resistance is of the order of 1 MOmega/sq, which indicates that conductivity is imparted by a network of an ultralow density. When the film transmittance decreases down to approximately 70% at 550 nm, the occupied surface area is approximately 15% and sheet resistance falls down to approximately 90 kOmega/sq. These data show that undesired in-plane clustering does not occur upon the dispersion casting of the films and that high-quality networks of CNT-g-P2VPs are built up. The electrosteric stabilization of the CNT-g-P2VP dispersions in water at low pH is at the origin of this desired behavior. Although the multiwalled CNT films prepared in this work are less conductive and less transparent than the SWNTs films, they could find applications, e.g., in touch screens, reflective displays, EMI shielding, and static charge dissipation.     

Singling out the electrochemistry of individual single-walled carbon nanotubes in solution

Bandgap fluorescence spectroscopy of aqueous, micelle-like suspensions of SWNTs has given access to the electronic energies of individual semiconducting SWNTs, while substantially lower is the success achieved in the determination of the redox properties of SWNTs as individual entities. Here we report an extensive voltammetric and vis-NIR spectroelectrochemical investigation of true solutions of unfunctionalized SWNTs and determine the standard electrochemical potentials of reduction and oxidation as a function of the tube diameter of a large number of semiconducting SWNTs. We also establish the Fermi energy and the exciton binding energy for individual tubes in solution. The linear correlation found between the potentials and the optical transition energies is quantified in two simple equations that allow one to calculate the redox potentials of SWNTs that are insufficiently abundant or absent in the samples.     

Bioelectrochemical single-walled carbon nanotubes

Metalloproteins and enzymes can be immobilized on SWNTs of different surface chemistry. The combination of high surface area, robust immobilization and inherent nanotube electrochemical properties is of promising application in bioelectrochemistry.     

Ultrafast dynamics of single-walled carbon nanotubes dispersed in polymer films

Wavelength-resolved femtosecond transient absorption spectroscopy is used to follow the electronic dynamics of single-walled carbon nanotubes in polymers following visible photoexcitation. Electron-hole (e-h) pairs give rise to sharp features in the transient spectra that decay in amplitude and exhibit rapid spectral shifts. The decay reflects (e-h) recombination on both short (1.3 ps) and long (35 ps) time scales. Transient spectra also exhibit a broad photobleach at early times that arises from the cooling of a hot electron gas created via excitation at the red edge of a pi-plasmon band.     

Nonlinear optical absorption of nanocomposite films made from polymers and single-walled carbon nanotubes: The effect of nanotube type and polymer matrix

Nonlinear optical absorption at a wavelength of 1080 nm for nanocomposite thin films made from polymers and single-walled carbon nanotubes (SWNTs) was studied by the longitudinal scanning (z-scan) technique. Two SWNT types differing in the synthesis procedure (HipCO and arc evaporation techniques) were used for the preparation of nanocomposites based on the polymers carboxymethylcellulose (CMC) and poly(vinyl alcohol) (PVAL). The nonlinear absorption coefficients were measured to be ?5.0 × 10^?7 and ?3.9 × 10^?7 cm/W for the CMC-SWNT/HipCO and CMC-SWNT/Arc composite films and ?1.7 × 10^?7 and ?0.9 × 10^?7 cm/W for the PVAL-SWNT/HipCO and PVAL-SWNT/Arc films, respectively. It was found that the film nanocomposites based on carboxymethylcellulose had a higher absolute value of the nonlinear absorption coefficient than the films in which PVAL was used as the polymer matrix.     

Direct electrochemistry of uric acid at chemically assembled carboxylated single-walled carbon nanotubes netlike electrode

Carboxylated single-walled carbon nanotubes (SWCNT) chemically assembled on gold substrate was employed as netlike electrode to investigate the charge-transfer process and electrode process kinetics using uric acid as an example. The electrochemical behavior of uric acid in carboxylated SWCNT system was investigated using cyclic voltammetry, chronoamperometry, and single potential time-based techniques. The properties of raw SWCNT electrode were also studied for comparison purpose. Uric acid has better electrochemical behavior whereas ascorbic acid has no effective reaction on the carboxylated SWCNT electrode. Cyclic voltammograms indicate that the assembled carboxylated SWCNT increases more active sites on electrode surface and slows down the electron transfer between the gold electrode and uric acid in solution. The charge-transfer coefficient (alpha) for uric acid and the rate constant (k) for the catalytic reaction were calculated as 0.52 and 0.43 s(-1), respectively. The diffusion coefficient of 0.5 mM uric acid was 7.5 x 10(-6) cm2 x s(-1). The results indicate that electrode process in the carboxylated SWCNT electrode system is governed by the surface adsorption-controlled electrochemical process.     

Symmetry of electron diffraction from single-walled carbon nanotubes

We show that, even when the atomic structure of a single-walled carbon nanotube does not have mirror symmetry perpendicular to the tubule axis, the electron diffraction patterns of the single-walled carbon nanotube always possess 2mm symmetry. We have also analyzed the contributions of higher order Bessel functions to the intensity distribution on the layer lines and found that (a) their contributions are negligible and (b) they would not affect the symmetry of the diffraction pattern. Both experimental and simulated electron diffraction patterns of a single-walled carbon nanotube of indices (14, 9) are presented to illustrate the 2mm symmetry and to corroborate the theoretical analysis.     

Soluble ultra-short single-walled carbon nanotubes

Soluble, ultra-short (length < 60 nm), carboxylated, single-walled carbon nanotubes (SWNTs) have been prepared by a scalable process. This process, predicated on oleum's (100% H2SO4 with excess SO3) ability to intercalate between individual SWNTs inside SWNT ropes, is a procedure that simultaneously cuts and functionalizes SWNTs using a mixture of sulfuric and nitric acids. The solubility of these ultra-short SWNTs (US-SWNTs) in organic solvents, superacid and water is about 2 wt %. The availability of soluble US-SWNTs could open opportunities for forming high performance composites, blends, and copolymers without inhibiting their processibility.     

Functional macromolecules from single-walled carbon nanotubes: synthesis and photophysical properties of short single-walled carbon nanotubes functionalised with 9,10-diphenylanthracene

9,10-Diphenylanthracene (DPA), a well-studied organic chromophore (Phi(fl) = 0.98) that exhibits electroluminescence, has been covalently bound through 2-(ethylthio)ethylamido linkers to the carboxylic acid groups of short, soluble single-walled carbon nanotubes (sSWNTs) of 1 microm average length, and the resulting DPA-functionalised sSWNT (DPA- sSWNT) macromolecular adducts (4.6 wt % DPA content) characterised by solution (1)H NMR, Raman and IR spectroscopy and thermogravimetric analysis. Comparison of the quenching of DPA fluorescence (steady-state and time-resolved) and of the transient optical spectra of sSWNTs and DPA-sSWNTs show that the covalent linkage boosts the interaction between the DPA and the sSWNT units. DPA-sSWNTs exhibit emission in the near-IR region from 1100-1400 nm with an enhanced quantum yield (Phi = 5.7x10(-3)) compared with sSWNTs (Phi = 3.9x10(-3)).     

Controlled orientation and alignment in films of single-walled carbon nanotubes using inkjet printing

An inkjet printing procedure for depositing films of carbon nanotubes (CNTs) that exhibit a very high degree of long-range mutual alignment as well as a controlled orientation with respect to the printed geometry is presented. CNT self-assembly was induced by the intrinsic lyotropic liquid crystallinity of CNT suspensions. Sufficient concentrations are reached by matching the inkjet deposition rate to the numerically modeled local evaporation rate of the printed feature and enable the CNT suspension to be printed using standard inkjet printing. Surface alignment was verified using scanning electron microscopy (SEM) and polarized light microscopy. In addition, the bulk morphology was investigated and found to be composed of stacked planar layers that did not necessarily have the same long-range orientation found on the surface. The bulk morphology was characterized by removing layers through an elastomeric peeling process and by observing cross sections of the films using SEM. CNT concentration and length were spanned experimentally, and it was found that very short and very long CNTs as well as low concentration suspensions did not yield long-range alignment.     

Incorporation of single-walled carbon nanotubes into ferrocene-modified linear polyethylenimine redox polymer films

In this study, we describe the effects of incorporating single-walled carbon nanotubes (SWNTs) into redox polymer-enzyme hydrogels. The hydrogels were constructed by combining the enzyme glucose oxidase with a redox polymer (Fc-C(6)-LPEI) in which ferrocene was attached to linear poly(ethylenimine) by a six-carbon spacer. Incorporation of SWNTs into these films changed their morphology and resulted in a significant increase in the enzymatic response at saturating glucose concentrations (3 mA/cm(2)) as compared to films without SWNTs (0.6 mA/cm(2)). Likewise, the sensitivity at 5 mM glucose was significantly increased in the presence of SWNTs (74 μA/cm(2)·mM) as compared to control films (26 μA/cm(2)·mM). We demonstrate that the increase in the electrochemical and enzymatic response of these films depends on the amount of SWNTs incorporated and the method of SWNT incorporation. Furthermore, we report that the presence of SWNTs in thick films allows for more of the ferrocene redox centers to become accessible. The high current densities of the hydrogels should allow for the construction of miniature biosensors and enzymatic biofuel cells.     

Water-soluble and optically pH-sensitive single-walled carbon nanotubes from surface modification

There is great interest in using single-walled carbon nanotubes (SWNTs) as nanoscale probes and sensors in biological electronics and optical devices because the electronic and optical properties of SWNTs are extremely sensitive to the surrounding environments. A well-controlled modification of SWNT surfaces may provide unique interfaces that are sensitive to the biological variables such as pH, glucose, various ions and proteins. In this paper, we report a facile chemical routine to prepare water-soluble SWNTs that still retain their van Hove singularities after acid oxidative treatment. The aqueous solutions (0.03-0.15 mg/mL) are stable for more than a month. The solubility in water for as-treated SWNTs with surfaces modified by carboxylate groups provides us with a unique opportunity to reveal the relationship of the SWNT electronic and optical properties with pH. Here we present the first observation that after surface modification with carboxylate groups, the optical absorption of the first interband transition of as-treated water-soluble semiconducting SWNTs reversibly responds to the pH change in aqueous solutions. Our results indicate that surface modification of SWNTs is a promising way for preparing chemically selective SWNT interfaces, which may open new exciting opportunities for various applications.     

Interactions between single-walled carbon nanotubes and lysozyme

Dispersions of single-walled and non-associated carbon nanotubes in aqueous lysozyme solution were investigated by analyzing the stabilizing effect of both protein concentration and pH. It was inferred that the medium pH, which significantly modifies the protein net charge and (presumably) conformation, modulates the mutual interactions with carbon nanotubes. At fixed pH, in addition, the formation of protein/nanotube complexes scales with increasing lysozyme concentration. Electrophoretic mobility, dielectric relaxation and circular dichroism were used to determine the above features. According to circular dichroism, lysozyme adsorbed onto nanotubes could essentially retain its native conformation, but the significant amount of free protein does not allow drawing definitive conclusions on this regard. The state of charge and charge distribution around nanotubes was inferred by combining electrophoretic mobility and dielectric relaxation methods. The former gives information on changes in the surface charge density of the complexes, the latter on modifications in the electrical double layer thickness around them. Such results are complementary each other and univocally indicate that some LYS molecules take part to binding. Above a critical protein/nanotube mass ratio, depletion phenomena were observed. They counteract the stabilization mechanism, with subsequent nanotube/nanotube aggregation and phase separation. Protein-based depletion phenomena are similar to formerly reported effects, observed in aqueous surfactant systems containing carbon nanotubes.     

Protein-assisted solubilization of single-walled carbon nanotubes

We report a simple method that uses proteins to solubilize single-walled carbon nanotubes (SWNTs) in water. Characterization by a variety of complementary techniques including UV-Vis spectroscopy, Raman spectroscopy, and atomic force microscopy confirmed the dispersion at the individual nanotube level. A variety of proteins differing in size and structure were used to generate individual nanotube solutions by this noncovalent functionalization procedure. Protein-mediated solubilization of nanotubes in water may be important for biomedical applications. This method of solubilization may also find use in approaches for controlling the assembly of nanostructures, and the wide variety of functional groups present on the adsorbed proteins may be used as orthogonal reactive handles for the functionalization of carbon nanotubes.     

Discrete dispersion of single-walled carbon nanotubes

Single-walled carbon nanotubes (SWNTs) have been effectively wetted and dispersed in saturated sodium hydroxide (NaOH) alcohol-water solutions with little surface damage or shortening of the tubes; the treated material was dissolvable as individual tubes in many common organic solvents.