Microwave activation of catalytic transformation of t-butylphenols

Kinetics of catalytic transformation of 2- and 4-t-butylphenol (2TBP and 4TBP) in the liquid phase on a heterogeneous KSF catalyst has been studied in detail under conventional and microwave conditions. The process includes dealkylation, isomerization and transalkylation reactions. Its kinetics has been described using the method of initial reaction rates. It was found that microwaves affect both the reaction rate and the selectivity. The results were explained in terms of “microwave-induced polarisation” assuming an interaction of microwaves with a highly polarised reagent molecule in adsorbed state on the acidic active site. Temperature and solvent effects were also examined. The reaction mechanism of t-butylphenol transformation is discussed on the basis of electrophilic aromatic substitution via bimolecular reactions.     

Alcoholysis of Poly(l-lactic acid) under microwave irradiation

Chemical recycling of poly(l-lactic acid) (PLLA) by alcoholysis under microwave irradiation was investigated. Reaction rates in ethanol (140-180 °C) and butanol (130-210 °C) were greater under microwave irradiation than under conventional heating. However, because activation energies were almost the same under both conditions, the reaction mechanisms would be the same, but the reaction rates differed due to the reaction frequency factor.     

Microwave-enhanced dechlorination of chlorobenzene

- Heterogeneous liquid-phase dechlorination of chlorobenzene over supported palladium-based catalysts to form benzene was examined using microwave and conventional heating methods. The reaction was carried out in a solution of NaOH in 2-propanol at atmospheric pressure and reflux temperature (approx. 83°C). Two types of commercial aluminium-silicate and -alumina-supported catalysts have been tested. The results obtained under microwave (MW) and conventional (CH) conditions were compared with respect to the rate enhancement, selectivity and catalyst activity. The sole product of the chlorobenzene dehalogenation was benzene. The effect of the addition of NaOH has been analysed for the neutralisation of HCl.     

Microwave-assisted amination of 3-bromo-2-chloropyridine with various substituted aminoethanols

A simple method for microwave-assisted amination of 3-bromo-2-chloropyridine with various substituted aminoethanols is described. The reaction was carried out under microwave irradiation conditions (at 180 °C for 1-2 h) and the result was superior in terms of conversion and yield when compared to that of the corresponding conventional heating conditions.     

Heck coupling reaction using monomeric ortho‐palladated complex of 4‐methoxy‐ benzoylmethylenetriphenylphosphorane under microwave irradiation

The activity of [Pd(C₆H₄CH₂ NH₂‐κ²‐C‐N)PPh₃MOBPPY]OTf complex, A (MOBPPY = 4‐methoxybenzoylmethylenetriphenyl‐ phosphoraneylide), was investigated in the Heck–Mizoroki C? C cross‐coupling reaction under conventional heating and microwave irradiation conditions. The complex is an active and efficient catalyst for the Heck reaction of aryl halides. The yields were excellent using a catalytic amount of [Pd(C₆H₄CH₂ NH₂‐κ²‐C‐N)PPh₃MOBPPY]OTf complex in N‐methyl‐2‐pyrrolidinone (NMP) at 130 °C and 600 W. In comparison to conventional heating conditions, the reactions under microwave irradiation gave higher yields in shorter reaction times. Copyright © 2010 European Peptide Society and John Wiley & Sons, Ltd.     

Microwave-assisted synthesis of 2-aminonicotinic acids by reacting 2-chloronicotinic acid with amines

2-(Methylamino)nicotinic acid was readily prepared in high yield by reacting 2-chloronicotinic acid with 40% aq MeNH₂ under microwave irradiation either at 120 °C for 2 h or at 140 °C for 1.5 h. Subsequently, we found that a range of 2-aminonicotinic acids could be obtained under microwave heating. The optimal reaction conditions involved the use of 3 equiv of amine, water as the solvent and heating at 200 °C for 2 h in the presence of diisopropylethylamine (3 equiv).     

Synthesis of benzo[<Emphasis Type="Italic">f</Emphasis>]quinoline derivatives by condensation of <Emphasis Type="Italic">N</Emphasis>-arylmethylene-2-naphthylamines with acetylcyclohexane and 1-acetylcyclohexene

N-Arylmethylene-2-naphthylamines react with acetylcyclohexane and 1-acetylcyclohexene under mild conditions to afford 2-aryl-2-(2-naphthylamino)ethyl cyclohexyl and 1-cyclohexenyl ketones, respectively. Under more severe conditions (110°C), the reaction is accompanied by cyclization with formation of 3-aryl-1-cyclohexyl(or 1-cyclohexenyl)benzo[f]quinolines. Proper choice of the amount of catalyst, temperature, and reaction time allows isolation of intermediate 3-aryl-1-cyclohexyl(or 1-cyclohexenyl)-3,4-dihydrobenzo[f]quinolines.Translated from Zhurnal Obshchei Khimii, Vol. 74, No. 11, 2004, pp. 1878–1883.Original Russian Text Copyright © 2004 by Grachek.This revised version was published online in April 2005 with a corrected cover date.     

Synthesis of α-aminonitriles under mild catalytic,metal-free conditions

α-Aminonitriles have been synthesized by a Strecker synthesis from aldehydes and ketones under mild catalytic, metal-free conditions. Aromatic aldehydes (1 equiv) were reacted with aromatic and 1° or 2° aliphatic amines (1 equiv) in EtOH containing 3 mol % of NH₄Cl to give high yields of α-aminonitriles. An alternative to adding NH₄Cl as a catalyst involved the use of excess TMSCN (1 equiv) and to promote the process. The reaction was also successful under microwave conditions using excess TMSCN with no solvent. Ketones similarly reacted with aromatic amines and excess TMSCN under conventional and microwave heating, but 30 mol % of added NH₄Cl was required for optimum conversion.     

Microwave Accelerated Polymerization of 2‐Phenyl‐2‐oxazoline

Summary: We studied the cationic ring‐opening polymerization of 2‐phenyl‐2‐oxazoline under microwave irradiation. A comparison with thermal heating shows a great enhancement in the reaction rates while the living character of the polymerization is conserved. The polymerizations were performed at the temperature of boiling butyronitrile (123 °C). The polymerization of 2‐phenyl‐2‐oxazoline under microwave conditions, described herein for the first time, is shown to be a rapid and environmentally friendly alternative to the classical methods.

Schematic of the activation of the reactive site by microwave irradiation.     

Hydrolysis of poly(l-lactic acid) using microwave irradiation

Poly(l-lactic acid) (PLLA) was hydrolyzed using microwave irradiation, and yields of the resultant lactic acid and reaction time were compared with those obtained by conventional heating. In both cases, the reaction temperature was maintained at 170 °C and the weight ratio of PLLA:H₂O was 3:1. Under conventional heating, the lactic acid yield reached saturation after 800 min at 45%, whereas only 120 min was required to reach the same yield level under microwave irradiation. The optical purity under conventional heating decreased with hydrolysis of the PLLA and dropped to 94%ee when the lactic acid yield reached at 45%. Under microwave irradiation, however, the optical purity decreased only after the equilibrium state of hydrolysis was attained. Therefore, to maintain the optical purity at 98%ee, it was necessary to stop microwave irradiation when the lactic acid yield reached 45%.     

Recycling of poly(ethylene terephthalate) waste through methanolic pyrolysis in a microwave reactor

In this study, the methanolic pyrolysis (methanolysis) of poly(ethylene terephthalate) (PET) taken from waste soft-drink bottles, under microwave irradiation, is proposed as a recycling method with substantial energy saving. The reaction was carried out with methanol with and without the use of zinc acetate as catalyst in a sealed microwave reactor in which the pressure and temperature were controlled and recorded. Experiments under constant temperature or microwave power were carried out at several time intervals. The main product dimethyl-terephthalate was analyzed and identified by FTIR and DSC measurements. It was found that PET depolymerization, is favored by increasing temperature, time and microwave power. High degrees of depolymerization were measured at temperatures near 180 °C and at microwave power higher than 150 W. Most of the degradation was found to occur during the initial 5–10 min. Compared to conventional pyrolysis methods, microwave irradiation during methanolic pyrolysis of PET certainly results in shorter reaction times supporting thus the conclusion that this method is a very beneficial one for the recycling of PET wastes.     

Single‐Mode Microwave Heating‐Induced Concurrent Out‐of‐Plane Twin Growth Suppression and In‐Plane Epitaxial Growth Promotion of b‐Oriented MFI Film under Mild Reaction Conditions

In this study, single‐mode microwave heating was applied in epitaxial growth of b‐oriented MFI seed monolayer prepared by facile manual assembly, resulting in the formation of well‐intergrown and highly b‐oriented MFI film with few twins. It exhibited a precise molecular sieving property at a reaction temperature no higher than 100 °C within 2 hours, therefore making it possible for easy operation in an open environment. The capability for concurrent suppression of undesired out‐of‐plane twin growth and promotion of in‐plane epitaxial growth rate under mild reaction conditions was attributed to the obvious superiority of single‐mode microwave heating in comparison with conventional multi‐mode microwave heating in aspects of microwave field uniformity and intensity. Our research indicated that the single‐mode microwave heating technique could potentially be a useful tool for improving the microstructure and therefore the performance of diverse zeolite films.     

Microwave Assisted Green Multicomponent Synthesis of Novel bis(2‐Amino‐tetrahydro‐4H‐chromene‐3‐carbonitrile) Derivatives Using Chitosan as Eco‐friendly Basic Catalyst

A simple, efficient, and eco‐friendly procedure has been developed for the synthesis of bis(4H‐chromene‐3‐carbonitrile) derivatives using chitosan as catalyst under microwave‐assisted reaction conditions. For the sake of comparison, the reaction was also carried out under conventional heating in the presence of each of chitosan and piperidine as basic catalysts.     

Addition of 1,2- and 1,3-Dithiols to 2-alkoxypropenals - a New Method for the Production of Substituted Dithiacycloalkanes

The reaction of 2-alkoxypropenals with ethane-1,2-dithiols and propane-1,3-dithiols under various conditions was studied by ¹H NMR and chromato-mass spectrometry. Under kinetically controlled conditions at 20° in the absence of catalysts the addition of dithiols takes place according to the Markovnikov rule. The primary adducts are unstable and are quickly converted into the corresponding substituted 1,4-dithiacycloheptane or 1,4-dithiane. The latter in turn can be converted under the reaction conditions or at high temperature into a thiolane derivative. The reaction of 2-ethoxypropenal with a twofold excess of ethane-1,2-dithiol at 60°C in the presence of p-toluenesulfonic acid leads to 2-methyl-2,2'-bi(dithiolane)     

Microwave Promoted and Improved Thermal Synthesis of Spiro[Indole‐Pyranobenzopyrans] and Spiro[Indole‐Pyranoimidazoles]

Spiro[indole‐pyranoimidazoles] ( 5 ) and spiro[indole‐pyranobenzopyrans] ( 6 ) are readily synthesized in one step in 86–92 and 91–97% yields by the Michael condensation of 3‐dicyanomethylene‐2H‐indol‐2‐ones ( 2 ) with 1‐phenyl‐2‐thiohydantoin ( 3 ) and 4‐hydroxy‐2H‐1‐benzopyran‐2‐one ( 4 ), respectively, without using any catalyst under different reaction conditions (conventional heating and microwave irradiation using (a) polar solvents (b) neutral alumina/silica gel as inorganic solid support in solvent free conditions). 2 was synthesized in situ by the Knoevenagel condensation of indole‐2,3‐dione ( 1 ) and malononitrile in the absence of any catalyst. 100% conversion was observed in most cases on TLC which also showed the formation of a single product. The comparison between the various methods is established.     

微波辐射活性炭负载磷钨酸催化合成季戊四醇双缩酮(醛)

在微波辐射下，以活性炭负载磷钨酸为催化剂，不用溶剂，合成了8种季戊四醇双缩酮（醛），以环己酮与季戊四缩的缩合为模型反应进行优化，其优化反应条件为：季戊四醇2．0g，催化剂0．3g，环己酮4．0mL，微波输出功率600W，辐射时间3min，产率达95．4％，该条件下的反应速度是常规加热反应速度的30倍，所得产物经元素分析，IR和1H NMR表征。     

A comparative homocoupling reaction of aryl halides using monomeric orthopalladated complex of 4‐methoxybenzoylmethylenetri‐ phenylphosphorane under conventional and microwave irradiation conditions

The activity of [Pd(C₆H₄CH₂NH₂‐κ²‐C‐N)PPh₃MOBPPY]OTf complex, A (MOBPPY = 4‐methoxybenzoylmethylenetriphenylphosphoraneylide) was investigated in the homocoupling reaction of a vast range of aryl halides under both conventional and microwave irradiation conditions and their results were compared. The complex was active and showed high efficiency in the formation of new C‐C bonds. The yields were excellent using a catalytic amount of [Pd(C₆H₄CH₂NH₂‐κ²‐C‐N)PPh₃MOBPPY]OTf complex in N, N‐dimethylformamide at 120 °C. In comparison to conventional heating conditions, the reactions under microwave irradiation gave higher yields in shorter reaction times. Copyright © 2011 John Wiley & Sons, Ltd.     

Copper-catalyzed rearrangement of oximes into primary amides

The atom-efficient and cost-effective rearrangement of oximes into primary amides is catalyzed by simple copper salts. The use of homogeneous Cu(OAc)₂ (1-2 mol %) was found to be effective for this transformation at 80 °C. The reaction was successful with either conventional or microwave heating. CuO and CuO/ZnO on activated carbon provided a competent reuseable heterogeneous catalyst which could be used in a batch process or in flow. Copper salts are much cheaper than the precious metals previously used for this rearrangement, and the reaction conditions are milder than those reported.     

Microwave-enhanced cyanation of aryl halides with a dimeric <Emphasis Type="Italic">ortho</Emphasis>-palladated complex catalyst

Abstract  

A new dimeric ortho-palladated complex of 2-methoxyphenethylamine was synthesized and characterized and its application as a cyanation catalyst was investigated. The main advantages of this catalyst are its easy preparation, handling, stability, and moisture insensitivity. Thus, [Pd{C₆H₃(CH₂CH₂NH₂)-4-OMe-5-κ ²-C,N}(μ-Br)]₂ showed excellent catalytic activity for the cyanation of aryl iodides and bromides with K₄[Fe(CN)₆], in DMF in the presence of K₂CO₃ under microwave irradiation and conventional heating at 130 °C to give the desired cyanoarene products in good to high yields. The less reactive aryl chlorides also react with K₄[Fe(CN)₆] to give moderate yields of the aromatic nitriles. The effects of various parameters such as solvent, base, and amount of catalyst were studied. The reaction is suitable for a wide variety of substituted aryl halides with different electronic properties. Application of microwave irradiation improved the yields of the reactions and reduced the reaction times from hours to minutes.     

Ruthenium–arene complexes bearing imidazol(in)ium-2-dithiocarboxylate ligands: Evaluation of their catalytic activity in the synthesis of enol esters

The catalytic activity of four ruthenium imidazol(in)ium-2-dithiocarboxylates was evaluated for the synthesis of vinyl esters through addition of 4-acetoxybenzoic acid to 1-hexyne, and compared to those of the parent ruthenium–N-heterocyclic carbene complexes and [RuCl₂(p-cymene)(PPh₃)] (a standard catalyst). It turned out that ruthenium imidazol(in)ium-2-dithiocarboxylates were poorly active and selective. Quantitative yields, indeed, were obtained only after extended reaction times. However, the catalytic activity could be improved significantly under microwave heating or conventional heating in a sealed tube at 160 °C, driving the reaction to completion in less than 4 h of reaction.