Novel Polymeric Membrane Sensors Based on Mn(III) Porphyrin and Co(II) Phthalocyanine Ionophores for Batch and Flow Injection Determination of Azide

Two novel potentiometric azide membrane sensors based on the use of manganese(III)porphyrin [Mn(III)P] and cobalt(II)phthalocyanine [Co(II)Pc] ionophores dispersed in plasticized poly(vinyl chloride) PVC matrix membranes are described. Under batch mode of operation, [Mn(III)P] and [Co(II)Pc] based membrane sensors display near‐ and sub‐Nernstian responses of ?56.3 and ?48.5 mV decade^?1 over the concentration ranges 1.0×10^?2?2.2×10^?5 and 1.0×10^?2?5.1×10^?5 mol L^?1 azide and detection limits of 1.5×10^?5 and 2.5×10^?5 mol L^?1, respectively. Incorporation of both membrane sensors in flow‐through tubular cell offers sensitive detectors for flow injection (FIA) determination of azide. The intrinsic characteristics of the [Mn(III)P] and [Co(II)Pc] based detectors in a low dispersion manifold show calibration slopes of ?51.2 and ?33.5 mV decade^?1 for the concentration ranges of 1.0×10^?5?1.0×10^?2 and 1.0×10^?4?1.0×10^?2 mol L^?1 azide and the detection limits are1.0×10^?5 and 3.1×10^?5 mol L^?1, respectively. The detectors are used for determining azide at an input rate of 40–60 samples per hour. The responses of the sensors are stable within ±0.9 mV for at least 8 weeks and are pH independent in the range of 3.9?6.5. No interferences are caused by most common anions normally associated with azide ion.     

Flow‐Through Potentiometric Sensors for Alizarin Red S Dye and Their Application for Aluminum Determination

Novel selective and sensitive poly (vinyl chloride) membrane sensors are developed for measuring alizarin red S (AR) based on the use of aliquate 336, Mg^IIphthalocyanine (MgPc), Cu^IIphthalocyanine (CuPc) and Fe^II phthalocyanine (FePc) plasticized poly (vinyl chloride) membrane. The sensors display Nernestian response with slopes of ‐50.6 ± 0.6 , ‐37.4 ± 0.5 , ‐37.7 ± 0.8 and ‐35.0 ± 0.7 mV decade^?1 over the range of 5.2 × 10^?6 to 1 × 10^?2 mol L^?1 for all of them and detection limits of 5.9 × 10^?7, 1.9 × 10‐^?6 2.3 × 10^?6 and 1.9 × 10^?6 mol L^?1 for aliquate, MgPc, CuPc and FePc membrane based sensor, respectively. The sensors exhibit long life span, long term potential stability, high reproducibility, fast response and good discrimination ability towards alizarinate ion in comparison with many other anions. A tubular detector based on aliquate, MgPc, CuPc and FePc was further developed and coupled to a flow‐injection system for alizarin (AR) determination. Under optimized conditions, the linearity range is 1.0 × 10^?5‐ 1.0 × 10^?1 mol L^?1, with a slope of ‐52.1 ± 0.8, 20.9 ± 0.7, 23.6 ± 0.4 and 25 ± 1.1 mV decade^?1 and a reproducibility of ± 0.8 mV (n = 6) for aliquate, MgPc, CuPc and FePc membrane based sensors, respectively. The sensor based on aliquate is further utilized for a potentiodynamic quantification of aluminum in sludge samples and deodorants. The buffered solution of alizarin was allowed to react in a flow system with aluminum. The calibration curve of Al was found to be linear over a concentration range of 0.1 to 1.8 and 1.0 ‐ 40 μg mL^?1 with a slope = 16.9 (r² = 0.993) and 1.76 (r² = 0.994) mV (μg/mL)^?1 and a detection limit of 0.08 and 0.5 μg mL^?1 for 10^?4 and 10^?3 mol L^?1 AR^? as a carrier, respectively. The method was successfully used for determining aluminum in sludge samples and deodorants. The data agree fairly well the nominal values and with results obtain by continuous flow hydride generation inductively coupled plasma (ICP) method.     

Flow‐Through Assay of Quinine Using Solid Contact Potentiometric Sensors Based on Molecularly Imprinted Polymers

Miniaturized potentiometric membrane sensors for quinine incorporated with molecular imprinted polymer (MIP) were synthesized and implemented. Planar PVC based polymeric membrane sensors containing quinine‐methacrylic and/or acrylic acid‐ethylene glycol methacrylate were dispensed into anisotropically etched wells on polyimide wafers. The determination of quinine was carried out in acidic solution at pH 6, where positively charged species predominated prevalently. The suggested miniaturized planner sensors exhibited marked selectivity, sensitivity, long‐term stability and reproducibility. At their optimum conditions, the sensors displayed wide concentration ranges of 4.0×10^?6–1.0×10^?2mol L^?1 and 1.0×10^?5–1.0×10^?2 mol L^?1 with slopes of about 61.3–55.7 mV decade^?1; respectively. Sensors exhibit detection limits of 1.2×10^?6 and 8.2×10^?6 mol L^?1 upon the use of methacrylic and acrylic acid monomers in the imprinted polymer, respectively. Validation of the assay method according to the quality assurance standards (range, within‐day repeatability, between‐day variability, standard deviation, accuracy, and good performance characteristics) which could assure good reliable novel sensors for quinine estimation was justified. Application of the proposed flow‐through assay method for routine determination of quinine in soft drinks was assayed and the results compared favorably with data obtained by the standard fluorimetric method.     

Sequential Injection Lab‐on‐Valve Procedure for the Determination of Amantadine Using Potentiometric Methods

Amantadine potentiometric detectors were developed, evaluated and incorporated in a SIA‐LOV manifold in order to accomplish the control of pharmaceutical formulations and urine. The electrodes incorporate α‐cyclodextrin as ionophore, dibutyl phthalate or 2‐fluorophenyl 2‐nitrophenyl ether as plasticizers and potassium tetrakis[3,5‐bis‐(trifluoromethyl)phenyl]borate (KTFPB) as cationic additive. The slope increased from 61.2 to 63.8 mV decade^?1 and the practical limit of detection from 2.6×10^?6 mol L^?1 to 2.5×10^?5 mol L^?1 when the plasticizer was changed from 2‐fluorophenyl 2‐nitrophenyl ether to dibutyl phthalate. When incorporated in the flow‐manifold the membranes composed by dibutyl phthalate or with 2‐fluorophenyl 2‐nitrophenyl ether presented slopes and a practical limit of detection of 69.8 mV decade^?1 and 1.5×10^?4 mol L^?1 or 73.7 mV decade^?1 and 5.4×10^?5 mol L^?1, respectively. The electrode presented stable responses for over a year, and were highly selective concerning the representative species of the two sample matrices assayed as interferents. Comparison of obtained results with those provided by reference methods and recovery assays, revealed adequate accuracy for control assays.     

Construction and Performance Characterization of Ion‐Selective Electrodes for Potentiometric Determination of Paroxetine Hydrochloride in Pharmaceutical Preparations and Biological Fluids

Three types of ion‐selective electrodes: PVC membrane, modified carbon paste (CPE), and coated graphite electrodes (CGE) have been constructed for determining paroxetine hydrochloride (Prx). The electrodes are based on the ion pair of paroxetine with sodium tetraphenylborate (NaTPB) using dibutyl phthalate as plasticizing solvent. Fast, stable and potentiometric response was obtained over the concentration range of 1.1×10^?5–1×10^?2 mol L^?1 with low detection limit of 6.9×10^?6 mol L^?1 and slope of a 56.7±0.3mV decade^?1 for PVC membrane electrode, the concentration range of 2×10^?5–1×10^?2 mol L^?1 with low detection limit of 1.2×10^?5 mol L^?1 and slope of a 57.7±0.6 mV decade^?1 for CPE, and the concentration range of 2×10^?5–1×10^?2 mol L^?1 with low detection limit of 8.9×10^?6 mol L^?1 and slope of a 56.1±0.1 mV decade^?1 for CGE. The proposed electrodes display good selectivity for paroxetine with respect to a number of common inorganic and organic species. The electrodes were successfully applied to the potentiometric determination of paroxetine hydrochloride in its pure state, its pharmaceutical preparation, human urine and plasma.     

A Simple Approach to Simultaneous Electroanalytical Quantification of Acetaminophen and Tramadol Using a Boron‐doped Diamond Electrode in the Existence of Sodium Dodecyl Sulfate

The present work describes the individual, selective and simultaneous quantification of acetaminophen (ACP) and tramadol hydrochloride (TRA) using a modification‐free boron‐doped diamond (BDD) electrode. Cyclic voltammetric measurements revealed that the profile of the binary mixtures of ACP and TRA were manifested by two irreversible oxidation peaks at about +1.04 V (for ACP) and +1.61 V (for TRA) in Britton‐Robinson (BR) buffer pH 3.0. TRA oxidation peak was significantly improved in the presence of anionic surfactant, sodium dodecyl sulfate (SDS), while ACP signal did not change. By employing square‐wave stripping mode in BR buffer pH 3.0 containing 8×10^?4 mol L^?1 SDS after 30 s accumulation under open‐circuit voltage, the BDD electrode could be used for quantification of ACP and TRA simultaneously in the ranges 1.0–70 μg mL^?1 (6.6×10^?6–4.6×10^?4 mol L^?1) and 1.0–70 μg mL^?1 (3.3×10^?6–2.3×10^?4 mol L^?1), with detection limits of 0.11 μg mL^?1 (7.3×10^?7 mol L^?1) and 0.13 μg mL^?1 (4.3×10^?7 mol L^?1), respectively. The practical applicability of the proposed approach was tested for the individual and simultaneous quantification of ACP and/or TRA in the pharmaceutical dosage forms.     

A Novel Potentiometric Membrane Sensor Based on Aryl Palladium Complex for Selective Determination of Thiocyanate in the Saliva and Urine of Cigarette Smokers

A highly selective potentiometric sensor for thiocyanate ion based on the use of a newly synthesized organo‐palladium ion exchanger complex dispersed in a plasticized poly(vinyl chloride) membrane is described. The sensor displays a Nernstian response (?57.8±0.2 mV decade^?1) over a wide linear concentration range of thiocyanate (1.0×10^?6–1.0×10^?1 mol L^?1 ), low detection limit (6.3×10^?7 mol L^?1), fast response (20 s), stable potential readings (±0.4 mV), good reproducibility (±0.9%), long term stability (8 weeks), high precision (±0.7%) and applicability over a wide pH range (4–10). Negligible interferences are caused by F^?, Cl^?, I^?, Br^?, NO₃^?, NO₂^?, CN^?, SO₄^2?, S₂O₃^2?, PO₄^3?, citrate, acetate and oxalate ions. Under hydrodynamic mode of operation (FIA), the calibration slope is ?51.1±0.1 mV decade^?1, the linear response range is 1.0×10^?5–1.0×10^?1 mol L^?1 SCN^? and the sample throughput is 40–45 per hour. The sensor is satisfactory used for manual and flow injection potentiometric determination of SCN^? in the saliva and urine of cigarette smokers and non smokers. The data agree fairly well with results obtained by the standard spectrophotometric technique. Direct potentiometry and potentiometric titration of SCN^? with Ag⁺ are also monitored with the sensor.     

A PVC Membrane Sensor for Potentiometric Determination of Atorvastatin in Biological Samples and Pharmaceutical Preparations

The present article reports for the first time the use of Aliquat 336S‐atorvastatin as an electroactive material in a poly(vinyl chloride) matrix membrane sensor plasticized with ortho‐nitrophenyl‐octylether (o‐NPOE) or dioctylphthalate (DOP) for determination of atorvastatin in biological samples (human plasma) and in pharmaceutical preparations. The sensor shows fast, stable and reproducible response over the concentration range of 1.0×10^?7–1.0×10^?2 mol L^?1 atorvastatin with anionic slopes of 60.94±0.2 and 58.22±0.2 and pH range of 5.0–9.0 for o‐NPOE and DOP plasticized based membrane sensors, respectively. The response time of the sensor is stable and fast (10 s). Results were achieved with average recoveries of 99.5 % and 99.3 % and mean standard deviations of ±1.1 % and ±1.4 % for o‐NPOE and DOP plasticized based membrane sensors, respectively. The sensor exhibits high selectivity towards atorvastatin in the presence of many anions, drug excipients and diluents. Validation of the method according to the quality assurance standards shows suitability of the proposed sensors for use in the quality control assessment of the drug.     

Development of a Novel Automatic Potentiometric System for Determination of Selenium and Its Application in Pharmaceutical Formulations and Anodic Slime

Poly(vinyl chloride) polymeric membrane sensors containing Sn(IV) phthalocyanine dichloride (SnPC) and Co(II) phthalocyanine (CoPC) as novel electroactive materials dispersed in o‐nitrophenyl octylether (o‐NPOE) as a plasticizer are examined potentiometrically with respect to their response toward selenite (SeO₃^2?) ions. Fast Nernstian response for SeO₃^2? ions over the concentration ranges 7.0×10^?6–1.0×10^?3 and 8.0×10^?6–1.0×10^?3 mol L^?l at pH 3.5–8.5 with lower detection limit of 5.0×10^?6 and 8.0×10^?6 mol L^?1 and calibration slopes of ?25.4 and ?29.7 mV decade^?1 are obtained with SnPC and CoPC based membrane sensors, respectively. The proposed sensors reveals by the modified separate solution method (MSSM) a good selectivity over different anions which differ significantly from the classical Hofmeister series. A segmented sandwich membrane method is used to determine complex formation constants of the ionophores in situe in the solvent polymeric sensing membranes. Membrane incorporating CoPC in a tubular flow detector is used in a two channels flow injection set up for continuous monitoring of selenite at a frequency of ca. 50 samples h^?1. Direct determination of selenium in pharmaceutical formulations and anodic slime gives results in good agreement with data obtained using standard ICP method.     

New Potentiometric Sensor for the Determination of Bromate Ion in Drinking Water

The characteristics, performance and application of ion‐selective electrodes for bromate ion based on rhodamine B and tetrahexyl ammonium bromide as electrode‐active substances are described for the first time. These electrodes respond with sensitivities of (58.0±1.0) and (61.0±2.0) mV decade^?1 over the range 1.0×10^?8–1.0×10^?2 mol l^?1 at pH 4–9 and 4–8 and a detection limit of 6.0×10^?8 and 4.0×10^?8 mol l^?1 for rhodamine B and tetrahexyl ammonium bromide sensors, respectively. The electrodes are easily constructed at a relatively low cost, have a fast response time and can be used for a period of 3 months without any considerable divergence in potential. The proposed sensors displayed good selectivity for bromate ion in the presence of several substances and inorganic anions. Sensors were used for the direct assay of bromate ion in drinking water samples.     

Lead(II) Potentiometric Sensor Based on 1,4,8,11‐Tetrathiacyclotetradecane Neutral Carrier and Lipophilic Additives

A potentiometric sensor for lead(II) ions based on the use of 1,4,8,11‐tetrathiacyclotetradecane (TTCTD) as a neutral ionophore and potassium tetrakis‐(p‐chlorophenyl)borate as a lipophilic additive in plasticized PVC membranes is developed. The sensor exhibits linear potentiometric response towards lead(II) ions over the concentration range of 1.0×10^?5–1.0×10^?2 mol L^?1 with a Nernstian slope of 29.9 mV decade^?1 and a lower limit of detection of 2.2×10^?6 mol L^?1 Pb(II) ions over the pH range of 3–6.5. Sensor membrane without a lipophilic additive displays poor response. The sensor shows high selectivity for Pb(II) over a wide variety of alkali, alkaline earth and transition metal ions. The sensor shows long life span, high reproducibility, fast response and long term stability. Validation of the method by measuring the lower limit of detection, lower limit of linear range, accuracy, precision and sensitivity reveals good performance characteristics of the proposed sensor. The developed sensor is successfully applied to direct determination of lead(II) in real samples. The sensor is also used as an indicator electrode for the potentiometric titration of Pb(II) with EDTA and potassium chromate. The results obtained agree fairly well with data obtained by AAS.     

A Novel Flow‐Through Planar Solid Contact Sensor for the Determination of Lead with Potentiometric Anionic Response

The construction and general performance characteristics of two poly(vinyl chloride) matrix chemical sensors for lead were described. These sensors were based on the use of ion association complexes of trihydroxoplumbate, [Pb(OH)₃]^? and tetraiodoplumbate, [PbI₄]^2?with cetylpyridinium chloride (CP) and iron(II)‐4,7‐bathophenanthroline [Fe(bphen)₃]²⁺ as novel electroactive materials dispersed in o‐nitrophenyloctyl ether (o‐NPOE) plasticizer for ionometric sensor controls, respectively. The sensing membrane (3×5 mm) is immobilized on a wafer polyimide chip (size 13.5×3.5 mm) to offer a planar miniaturized design that could be easily used flow injection system. Under static modes of operation, the sensors revealed a near Nernstian response over a wide Pb²⁺ ion concentration range 7.9×10^?7 to 10^?4 and 3.2×10^?7 to 10^?4 mol L^?1 with detection limit of 100 and 45.5 ng mL^?1, respectively . In flow injection potentiometry, excellent reproducibility (RSD%=0.5%), fast response, high sensitivity, high sampling rate (50 sample h^?1) and stable baseline was observed in the presence of 5×10^?2 mol L^?1 NaOH and 10^?1 mol L^?1 KI as a carrier for [CP][Pb(OH)₃] and [Fe(bphen)₃][PbI₄] membrane based sensors, respectively. Validation of the assay method according to the quality assurance standards (range, within‐day repeatability, between‐day variability, standard deviation, accuracy, lower detection limit) reveals good performance characteristics and suggests application for routine determination of lead in industrial wastewaters and stack emissions of lead smelters. The results agree fairly well with data obtained by the standard atomic absorption methods.     

Man‐Tailored Biomimetic Sensor of Molecularly Imprinted Materials for the Potentiometric Measurement of Rivastigmine in Tablets and Biological Fluids and Employing the Taguchi Optimization Methodology to Optimize the MIP‐Based Membranes

This work proposes a novel biomimetic sensor for the potentiometric transduction of rivastigmine based on molecularly imprinted polymer (MIP). Using the Taguchi method, this study analyzed the optimum conditions for preparing the MIP‐based membranes. The rank order of each controllable factor was also determined. MIP‐based membranes exhibited a Nernstian response (30.7±1.1 mV decade^?1) in a concentration range from 1.0×10^?5 to 1.0×10^?2 mol L^?1 with a LOD of 6.3×10^?6 mol L^?1. The sensor was successfully applied to the determination of rivastigmine concentrations in human serum, plasma, urine, rat brain and tablets.     

Construction and Validation of New Electrochemical Carbon Nanotubes Sensors for Determination of Acebutolol Hydrochloride in Pharmaceuticals and Biological Fluids

A simple, rapid and a highly selective method for direct electrochemical determination of acebutolol hydrochloride (AC) was developed. The developed method was based on the construction of three types of sensors conventional polymer (I), carbon paste (II) and modified carbon nanotubes (MCNTs) carbon paste (III). The fabricated sensors depend mainly on the incorporation of acebutolol hydrochloride with phosphotungstic acid (PTA) forming ion exchange acebutolol‐phosphotungstate (AC‐PT). The performance characteristics of the proposed sensors were studied. The sensors exhibited Nernstian responses (55.6 ± 0.5, 57.14 ± 0.2 and 58.6 ± 0.4 mV mol L^?1) at 25 °C over drug concentration ranges (1.0 × 10^?6‐1.0 × 10^?2, 1.0 × 10^?7‐1.0 × 10^?2 and 5.0 × 10^?8‐1.0 × 10^?2 mol L^?1 with lower detection limits of (5.0 × 10^?7, 5.0 × 10^?8 and 2.5 × 10^?8 mol L^?1 for sensors (I), (II) and (III), respectively. The influence of common and possible interfering species, pharmaceutical additives and some related pharmacological action drugs was investigated using separate solution method and no interference was found. The stability indicating using forced degradation of acebutolol hydrochloride was studied. The standard addition method was used for determination of the investigated drug in its pharmaceutical dosage forms and biological fluids. The results were validated and statistically analysed and compared with those from previously reported methods.     

Determination of Ethambutol in Aqueous Medium Using an Inexpensive Gold Microelectrode Array as Amperometric Sensor

In this paper, gold microelectrode array (Au‐MEA) were employed to determination of ethambutol in aqueous medium. Au‐MEA was constructed with an electronic microchip integrated circuit. The standard curve (analytical curve) was constructed for a single microelectrode (ME) in a concentration range of 5.0×10^?5 to 2.0×10^?3 mol L^?1, allowing estimation of both the limit of detection (LOD) (4.73×10^?5 mol L^?1) and the limit of quantification (LOQ) (1.57×10^?4 mol L^?1) for ethambutol. When the MEA was utilized, the LOD and LOQ were 1.55×10^?7 and 5.18×10^?7 mol L^?1, respectively. Our results indicated that Au‐MEA can be utilized as amperometric sensors for ethambutol determination in aqueous media.     

Pattern Recognition of Sweeteners in Biological Fluids,Beverages, and Ketchup using Stochastic Sensors

Three stochastic sensors based on nanodiamond (nDP) paste modified with α, β, and γ‐cyclodextrin were designed and characterized for pattern recognition of aspartame, acesulfame K and sodium cyclamate in beverages, ketchup, and biological fluids. The linear concentration ranges obtained for acesulfame K (between 1.00×10^?10 mol L^?1and 1.00×10^?3 mol L^?1), for aspartame (between 1.00×10^?12 mol L^?1 and 1.00×10^?3 mol L^?1) and for sodium cyclamate (between 4.97×10^?12 mol L^?1 and 4.97×10^?3 mol L^?1) allow their assay in biological fluids, beverages and ketchup. The lowest limits of quantification were obtained using the stochastic sensor based on γ‐CD/nDP: for acesulfame K 1.00×10^?10 mol L^?1, for aspartame 1.00×10^?12 mol L^?1 and for sodium cyclamate 4.97×10^?12 mol L^?1. All three stochastic sensors revealed very high values of sensitivities. The proposed method was reliable for qualitative and quantitative assay of aspartame, acesulfame K and sodium cyclamate in beverages, ketchup, and in biological fluids such as urine.     

Nanostructured Alpha‐Nickel Hydroxide Electrodes for High Performance Hydrogen Peroxide Sensing

Nanostructured alpha‐nickel hydroxide (α‐Ni(OH)₂) immobilized on a Fluorine‐doped Tin Oxide (FTO) surface was explored for the construction of hydrogen peroxide amperometric Flow Injection Analysis (FIA) sensors. Their notable electrocatalytic activity and heterogeneous electron‐transfer rate were confirmed by the appearance of a broad and intense peak associated with the oxidation of hydrogen peroxide and the enhancement of sensibility in hydrodynamic conditions. The α‐Ni(OH)₂ electrodes exhibited a broad dynamic range (5×10^?6 to 1×10^?3 mol L^?1), low detection limit (2×10^?7 mol L^?1), good repeatability (RSD=1.29 % for 20 successive analyses), and a sensitivity greater than 500 µA mmol^?1 L^?1 cm^?2.     

Voltammetric Ion‐Selective Nanocomposite Carbon Paste Electrode for Determination of Erbium at the Interface Between two Immiscible Electrolyte Solutions

In this study for the first time a novel erbium(III) voltammetric ion‐selective nanocomposite carbon‐paste electrode was introduced based on the concept of ion transfer at the interface between two immiscible electrolyte solutions. N′‐(2‐hydroxy‐1,2‐diphenylethylidene) benzohydrazide (HDB) was used as a selective ionophore in the composition of the carbon paste. The ionophore facilitates transfer of Er(III) from the aqueous solution to the room temperature ionic liquid (RTIL) phase after reduction of the redox probe to maintain charge neutrality. The plot of the peak potential versus the logarithm of the concentration exhibits a Nernstian response (19.9±0.2 mV decade^?1) toward Er(III) in the range of 7.5×10^?7–1.0×10^?1 mol L^?1 with detection limit of 5.0×10^?7 mol L^?1. The proposed sensor shows a fast response time of about 5 s.     

Study of a Novel Bisnaphthalimidopropyl Polyamine as Electroactive Material for Perchlorate‐selective Potentiometric Sensors

In this work, the new polyamine bisnaphthalimidopropyl‐4,4’‐diaminodiphenylmethane is proposed as a new ionophore for perchlorate potentiometric sensors. The optimal formulation for the membrane comprised of 12 mmol kg^?1 of the ionophore, and 68 % (w/w) of 2‐nitrophenyl phenyl ether as plasticizer and 31 % (w/w) of high molecular weight PVC. The sensors were soaked in water for a week to allow leakage of anionic impurities and for one day in a perchlorate solution (10^?4 mol L^?1) to improve reproducibility due to its first usage. The stability constant for the ionophore‐perchlorate association in the membrane, log β_IL1=3.18±0.04, ensured a performance characterized by the slope of 54.1 (±0.7) mV dec^?1 to perchlorate solutions with concentrations between 1.24×10^?7 and 1.00×10^?3 mol L^?1. The sensors are insensitive to pH between 3.5 to 11.0, they have a practical detection limit of 7.66 (±0.42) ×10^?8 mol L^?1 and a response time below 60 s for solutions with perchlorate concentrations above 5×10^?6 mol L^?1. The accuracy of the results was confirmed by the analysis of the contaminant in a certified reference water sample.     

Fabrication of chemically modified carbon paste electrode based on functionalized biopolymer for potentiometric determination of Al (III) ion in real water and pharmaceutical samples

Carbon paste electrode modified with Carboxymethyl chitosan-graft-poly(1-cyanoethanoyl-4-acryloyl-thiosemcarbazide)copolymers(CMCS-PCEATS) as ionophore was constructed for potentiometric determination of aluminum (III) and the chelation between the ionophore and the aluminum (III) ions at the electrode surface was characterized using SEM, EDX, and IR analysis. Thermal stability of the prepared electrode before and after chelation with the metal ion was investigated. The highest performance was obtained with the electrode modified with 10 mg of the prepared copolymers plasticized with TCP (electrode I). Under the optimized provision, the electrode I shows Nernstian slope of 19.9?±?0.36 mV decade^??1 over the concentration range from 1.0?×?10^??6 to 1.0?×?10^??2 mol L^??1 with a detection limit of 1.0?×?10^??6 mol L^??1 and pH ranges from 3 to 8. The paste is enough stable for 37 days without any detected change in the potential. The proposed method is more potent in determination of Al(III) in both real water and pharmaceutical samples potentiometrically. The results obtained agreed with those obtained with spectrophotometer and inductive coupled plasma (ICP).