Adsorptive Stripping Voltammetric Determination of Albendazole at a Hanging Mercury Drop Electrode

ABSTRACT

Albendazole is determined by differential-pulse adsorptive cathodic stripping voltammetry at a hanging mercury drop electrode using the reduction peak of its copper(II) complex at ?0.28V at an accumulation potential 0.0V vs. Ag/AgCl electrode. The optimum conditions of pH, accumulation potential and accumulation time were studied. The calibration graph for the determination of albendazole was linear in the range 3.0X10^?8 - 9X10^?7M with a relative standard deviation of 2.8%. The detection limit was 1.0X10^?8M after 180s accumulation at 0.0V. The effect of common excipients and metal ions on the peak height of albendazole was studied. The presence of Cu²⁺ ions forms a stable complex with albendazole which is strongly adsorbed at the mercury electrode surface. The method was applied to the determination of the drug in commercially available dosage forms.     

Determination of Amitraz Pesticide by Adsorptive Stripping Voltammetry on the Hanging Mercury Drop Electrode

 A sensitive method for the determination of amitraz pesticide at nanomolar level by adsorptive stripping voltammetry at a hanging mercury drop electrode is described. The cyclic voltammograms demonstrate the adsorption of this compound on the mercury electrode. A systematic study of the various experimental parameters, that affect the stripping response, was carried out by differential pulse voltammetry. Using an accumulation potential of −0.50 V, and 30 s accumulation time, the limit of detection was found to be 2.3 × 10⁻⁹ mol L⁻¹ and the relative standard deviations (n = 5) was 2.2% at concentration level of 5.0 × 10⁻⁸ mol L⁻¹ of amitraz. The influence of diverse ions and some other pesticides was investigated. Finally, the method was applied to the determination of amitraz in spiked soil and water. The relative standard deviation is 4.5% for 5 determinations of amitraz in water and 3.2% for 5 determinations in soil. Received December 6, 2000. Revision March 1, 2001.     

Determination of atrazine using square wave voltammetry with the Hanging Mercury Drop Electrode (HMDE)

This paper presents the optimization of instrumental and solution parameters for determination of atrazine in river waters and formulation by square wave voltammetry (SWV) using a hanging mercury drop electrode. The best sensitivity (35.2±0.4 μA ml μg⁻¹) was achieved using a frequency of 400 Hz and a medium composed of 40 mmol l⁻¹ Britton-Robinson (BR) buffer at pH 1.9. The detection limit was 2 μg l⁻¹ with a linear dynamic range between 10 and 250 μg l⁻¹. Application of the method to real samples of river waters fortified with 10 μg l⁻¹ of atrazine resulted recoveries between 92 and 116%. Additionally, good agreement was observed between results obtained by the proposed method and by HPLC for river water samples spiked with 25 μg l⁻¹ of atrazine. The determination was not affected by the presence of humic acid at concentration of 5 mg l⁻¹, indicating that interactions of the herbicide with this class of compounds are fully labile. The stability of the voltammetric signal for samples spiked with 250 μg l⁻¹ atrazine was evaluated over a period of 14 days in four samples. For two samples, no systematic variation was observed, while for the other two, a decrease of peak current between 3 and 15% occurred, suggesting that the stability is dependent on the sample nature. HPLC analyses suggest formation of deethylatrazine during the second week of storage in the samples for which the SWV peak current had the more intense decrease.     

铜的腺嘌呤络合物在悬汞电极表面上的吸附形态和氧化还原行为

本文详细地研究了铜的腺嘌呤（Ａｄｅ）络合物在悬汞电极（ＨＭＤＥ）表面上的吸附形态和伏安行为。实验结果揭示了单层吸附饱和之前有Ｃｕ＾＋Ａｄｅ，Ｃｕ２＾＋（Ａｄｅ）２形态的共吸附作用，随着电极表面的吸附浓度增长，Ａｄｅ络合物分子有从平面向垂直吸附的定向作用。哦的多层吸附和聚合作用发生在吸附分子垂直定向以后。本文还测定了有关电极过程的动力学参数。     

Determination of Folic Acid at a Bismuth Film Electrode by Adsorptive Stripping Voltammetry

This article reports a new simple and sensitive method for the determination of folic acid by adsorptive stripping voltammetry. The method is based on the accumulation of folic acid at a bismuth film plated in situ on a glassy carbon substrate. In order to stabilize bismuth ions, sodium potassium tartrate was added to the supporting electrolyte. The bismuth film formation and folic acid accumulation conditions were optimized and measurements were carried without solution deaeration. The calibration graph was linear from 5 × 10^?10 to 2 × 10^?8 mole per liter with an accumulation time of 180 seconds with a limit of detection of 2 × 10^?10 mole per liter. The relative standard deviation for 5 × 10^?9 mole per liter of folic acid was 3.1 percent (n = 5). The method was successfully applied for determination of folic acid in pharmaceutical preparations.     

From Electrode Surface Fouling to Sensitive Electroanalytical Determination of Phenols

The present investigation of phenol and chlorophenols is conducted on the surface of glassy carbon by cyclic and square wave stripping voltammetry, and by Fourier‐transform infrared spectroscopy. The surface fouling is accompanied by the appearance of reversible peaks at lower potential range (+0.1 to+0.4 V), that grew up with CV‐cycling and attributed to the electro‐redox reactions of formed polymer film via electropolymerization. The electroanalytical monitoring of formed polymer oxidation peaks improved both sensitivity and detection limit by 35 and 10 times, respectively. The FT‐IR supported semiempirical prediction attributes the electropolymerization to the formation of ortho‐para and/or ortho‐meta C? C coupled‐system.     

Development of Uric Acid Sensor Based on Molecularly Imprinted Polymer‐Modified Hanging Mercury Drop Electrode

Uric acid (UA) sensor based on molecularly imprinted polymer‐modified hanging mercury drop electrode was developed for sensitive and selective analysis in aqueous and blood serum samples. The uric acid‐imprinted polymer was prepared from melamine and chloranil and coated directly onto the surface of a hanging mercury drop electrode, under charge‐transfer interactions at +0.4 V (vs. Ag/AgCl), in model 303A electrode system connected with a polarographic analyzer/stripping voltammeter (PAR model 264A). The binding event of uric acid was detected in the imprinted polymer layer through differential pulse, cathodic stripping voltammetry (DPCSV) at optimized operational conditions [accumulation potential +0.4 V (vs. Ag/AgCl), accumulation time 120 s, pH 7.0, scan rate 10 mV s^?1, pulse amplitude 25 mV]. The limit of detection for UA was found to be 0.024 μg mL^?1 (RSD=0.64%, S/N=3). Under the optimized operational conditions, the sensor was able to differentiate between uric acid and other closely structural‐related compounds and interfering substances. Ascorbic acid (AA), a major interferent in UA estimation, was not adsorbed on the surface of sensor electrode. The present sensor is, therefore, UA‐selective at all concentrations of AA present in human blood serum samples. The précised and accurate quantification of UA have been made in the dilute as well as concentrated regions varying within limits 0.1–4.0 and 9.8–137.0 μg mL^?1, respectively.     

Electrochemical Behavior and Electroanalytical Determination of Indole‐3‐Acetic Acid Phytohormone on a Boron‐Doped Diamond Electrode

In this work, a boron‐doped diamond (BDD) electrode was used for the electroanalytical determination of indole‐3‐acetic acid (IAA) phytohormone by square‐wave voltammetry. IAA yielded a well‐defined voltammetric response at +0.93 V (vs. Ag/AgCl) in Britton–Robinson buffer, pH 2.0. The process could be used to determine IAA in the concentration range of 5.0 to 50.0 µM (n=8, r=0.997), with a detection limit of 1.22 µM. The relative standard deviation of ten measurements was 2.09 % for 20.0 µM IAA. As an example, the practical applicability of BDD electrode was tested with the measurement of IAA in some plant seeds.     

Adsorptive Stripping Analysis of Riboflavin at Electrically Heated Graphite Cylindrical Electrodes

Electrically heated graphite cylindrical electrodes (HGCEs) made from ground pencil leads have been used to perform adsorptive stripping square wave voltammetry (SWV) measurements of trace riboflavin (RF). The SWV stripping peak current was significantly enhanced with increasing the electrode temperature only during preconcentration step. This enhancement was due to the forced thermal convection induced by heating the electrode rather than the bulk solution. It is the thermal convection that has the ability to improve mass transfer and facilitate adsorption thus enhance stripping responses. It was found that the detection limit of 5×10^?9 M (S/N=3) could be obtained at an electrode temperature of 72 °C during 5 min accumulation, more than one magnitude lower than that at 22 °C (room temperature), the sensitivity could be enhanced ca. eight or four folds for two different RF concentration ranges. So it is possible to develop a new highly sensitive method to determine riboflavin at HGCEs. Such HGCEs were also successfully used to determine RF in multivitamin tablets.     

The Convenient Determination of Palladium at a Solid Electrode via Adsorptive Stripping Voltammetry at a Glassy Carbon Electrode Modified with a Random Array of Mercury Nanodroplets

The detection of palladium using adsorptive stripping voltammetry reported by Wang et al. (J. Wang, K. Varughese Anal. Chim. Acta 1987, 199, 185 [3]) at a hanging mercury drop electrode is extended to a more convenient solid electrode. To this end a random array of 3.5×10⁸ mercury nanodroplets per cm² (65 nm average diameter) was electrodeposited on a glassy carbon substrate. Adsorptive stripping voltammetry was performed using 2×10^?4 M dimethylglyoxime as a chelating agent for the Pd(II) ion, with accumulation at ?0.20 V vs. SCE for 120 s and a linear detection range of 5–150 μM was determined with a limit of detection of 1.6 μM.     

Development of an Electroanalytical Method for the Quantification of Zearalenone (ZEA) in Maize Samples

The application of electroanalytical techniques to detect and quantify zearalenone (ZEA) mycotoxin that frequently contaminates maize and foodstuff is studied in this work. Rice and maize grains were inoculated with Fusarium fungus to obtain ZEA in artificially infected samples. The electro‐oxidation of ZEA adsorbed on the surface of glassy carbon (GC) electrodes in 20% acetonitrile (ACN)+80% 1 M HClO₄ (aqueous solution) reaction medium was studied by using square‐wave voltammetry (SWV). Studies were conducted to find the most favorable accumulation potential (E_acc) and accumulation time (t_acc) to perform the ZEA preconcentration on the electrode surface. It was found that E_acc was any value in the range from 0.00–0.90 V and the best t_acc was 120 s, respectively, for ZEA separated from extracting solution by TLC (ZEA_TLC) while E_acc=0.90 V corresponded to ZEA in non separated matrix solution (ZEA_matrix). The ZEA quantitative determination was performed by SWV combined with the standard addition method. Linear plots were obtained from the net peak current (I_{p, n}) vs c*_ZEA in the concentration range from 20 to 3184 ppb. Detection limit of 30 ppb at a signal to noise ratio of 3 : 1 was obtained. On the other hand, recovery experiments were performed on uncontaminated maize samples spiked with ZEA.     

Determination of Cr (in small quantities) by adsorptive stripping voltammetry: a comparative study of square wave versus differential pulse

The usefulness of an analytical method must be measured according to its practical application possibilities. A comparative study has been carried out here between the SW (working in an open atmosphere) and DP (working with de-aerated solutions) variants of catalytic-stripping adsorptive voltammetry applied to the determination of chromium traces in triethylenetetraminehexaacetic acid (TTHA) medium. In order to optimise the analytical signal, accumulation potential, nitrate ion concentration, pH, and TTHA concentration parameters were evaluated. Four linearity ranges were established within the interval 0.5–2000 nmol L^–1 chromium concentration in the cell, each with the recommended accumulation time. Quality parameters such as repeatability, linear regression, validity limits, precision, and sensitivity were evaluated. The SW variant is significantly advantageous when the chromium concentration in cell is less than 10 nmol L^–1 and even more if analysis time, cost, and being able to work in an open atmosphere are considered. The results are comparable to those obtained using GTAAS. Employing a CRM (tomato leaves), the accuracy is 1–4%. The proposed procedure, using tree leaves as samples, has been successfully tested for the possible monitoring of chromium contamination of the atmosphere.     

A Validated Voltammetric Procedure for Quantification of the Antifungal Drug Griseofulvin in Bulk Form,Tablets, and Biological Fluids at a Mercury Electrode

Abstract

Griseofulvin is an antifungal antibiotic used to treat various pathogenic mycotic diseases. The voltammetric behavior of griseofulvin at a hanging mercury drop electrode in Britton‐Robinson buffers of pH 2–11.5 was studied and discussed. A fully validated sensitive square‐wave adsorptive cathodic stripping voltammetric procedure was described for direct determination of bulk griseofulvin substance. The procedure was based on the reduction of the >C?O double bond of griseofulvin molecule following its preconcentration onto a hanging mercury drop electrode in a Britton‐Robinson buffer of pH 10. Limits of detection (LOD) and quantitation (LOQ) of 5.8×10^?10 M and 1.93×10^?9 M bulk griseofulvin were achieved, respectively. The proposed stripping voltammetric procedure was successfully applied to assay griseofulvin in tablets and in spiked human serum and urine samples. LOD of 8.65×10^?10 M and 6.6×10^?9 M and LOQ of 2.88×10^?9 M and 2.2×10^?8 M griseofulvin in spiked human serum and urine samples, respectively, were achieved.     

安乃近在蒙脱土修饰电极上的电化学行为及测定

制备了蒙脱土修饰电极,并采用循环伏安法研究了安乃近在该电极上的电化学行为。结果表明,该电极过程是一受扩散控制的不可逆过程。用方波溶出伏安法优化了实验参数,测定了浓度与峰电流Ipa的线性关系,发现Ipa与安乃近浓度在2.0×10-6~8.0×10-5mol.L-1之间呈良好的线性关系,其线性回归方程为:Ipa(μA)=-0.07784-15443.54c(μmol.L-1),r=-0.9993,检出限可达1.12×10-6mol.L-1,回收率为94.0%~108.25%。该方法可用于药物中安乃近含量的测定。     

Adsorptive Stripping Voltammetric Measurements of Trace Molybdenum at the Bismuth Film Electrode

Bismuth‐film electrodes on glassy‐carbon substrates have been successfully applied for adsorptive‐stripping voltammetric measurements of trace molybdenum in the presence of chloranilic acid (CAA). The procedure is based on the preconcentration of the molybdenum‐chloranilic acid complex at a preplated bismuth film electrode held at ?0.55 V (vs. Ag/AgCl), followed by a negatively‐sweeping square‐wave voltammetric scan. Factors influencing the adsorptive stripping performance, including different ligands, solution pH, CAA concentration, preconcentration time and potential, have been optimized. The response compares favorably with that observed at mercury film electrodes, and is linear over the 5–50 μg/L Mo concentration range (one min preconcentration). A detection limit of 0.2 μg/L molybdenum is obtained following a 10 min accumulation. High stability is indicated from the reproducible response of a 100 μg/L molybdenum solution (n= 60; RSD=2.6%). Applicability to seawater samples is demonstrated.     

Mercury Detection in Seawater Using a Mercaptoacetic Acid Modified Gold Microwire Electrode

It is demonstrated here that it is possible to determine mercury in chloride containing media like seawater by anodic stripping voltammetry using a modified electrode. A gold microwire electrode is modified using mercaptoacetic acid (MAA) to eliminate the problem of calomel formation, allowing the mercury to become fully removed from the electrode surface after each scan. In a synthetic salt solution of KNO₃ the sensitivity for mercury was found to be improved by the surface modification. In seawater the sensitivity was not significantly improved possibly because of complexation of the mercury by the abundant chloride; however, the MAA coating prevented the formation of calomel causing the background scan to be free of mercury. Measurements in seawater at various pH values demonstrated that mercury detection is possible at natural pH (around 8); however, best sensitivity was attained at pH 4.8 with a deposition time of 3 min. A peak for copper occurred at more negative potential but did not interfere at this pH. The calibration was linear between 0 and 37 nM mercury with a limit of detection of 1 nM mercury.     

Imprinted Polymer – Modified Hanging Mercury Drop Electrode for Differential Pulse Adsorptive Stripping Voltammetric Analysis of a Diquat Herbicide

An imprinted polymer modified hanging mercury drop electrode (HMDE) in Model 303A system in conjunction with a PAR Model 264A Polarographic Analyzer/Stripping Voltammeter has been used for the selective analysis of a diquat herbicide viz., 5,6‐dihydropyrazino[1,2,3,4‐[lmn]‐1,10‐phenanthrolinium dichlorides in differential pulse cathodic stripping voltammetry mode. Complex aqueous samples (drinking water and agricultural soil suspension), spiked with a diquat herbicide, were directly analyzed by the adsorptive accumulation of the analyte over the working electrode (accumulation potential ?0.8 V (vs. Ag/AgCl), accumulation time 120 s, pH 7.0, supporting electrolyte 0.1 M KCl, scan rate 10 mV s^?1, pulse amplitude 25 mV). The limit of detection for diquat herbicide was found to be 0.34 nmol L^?1 (0.1 ppb, RSD 2%, S/N=2).     

Electroanalytical Determination of Carbaryl in Natural Waters on Boron Doped Diamond Electrode

The anodic voltammetric behavior of carbaryl on a boron‐doped diamond electrode in aqueous solution is reported. The results, obtained by square‐wave voltammetry at 0.1 mol L^?1 Na₂SO₄ and pH 6.0, allow the development of a method to determine carbaryl, without any previous step of extraction, clean‐up, preconcentration or derivatization, in the range 2.5–30.0×10^?6 mol L^?1, with a detection limit of 8.2±0.2 μg L^?1 in pure water. The analytical sensitivity of this electrochemical method diminished slightly, from 3.07 mA mmol^?1 L to 2.90 mA mmol^?1L, when the electrolyte was prepared with water samples collected from two polluted points in an urban creek. In these conditions, the recovery efficiencies obtained were around 104%. The effect of other pesticides (fenthion and 4‐nitrophenol) was evaluated and found to exert a negligible influence on carbaryl determination. The square‐wave voltammetric data obtained for carbaryl were typical of an irreversible electrode process with mass transport control. The combination of square‐wave voltammetry and diamond electrodes is an interesting and desirable alternative for analytical determinations.     

Electroanalytical Determination of N‐Nitrosamines in Aqueous Solution Using a Boron‐Doped Diamond Electrode

The electrochemical methods cyclic and square‐wave voltammetry were applied to develop an electroanalytical procedure for the determination of N‐nitrosamines (N‐nitrosopyrrolidine, N‐nitrosopiperidine and N‐nitrosodiethylamine) in aqueous solutions. Cyclic voltammetry was used to evaluate the electrochemical behaviors of N‐nitrosamines on boron‐doped diamond electrodes. It was observed an irreversible electrooxidation peak located in approximately 1.8 V (vs. Ag/AgCl) for both N‐nitrosamines. The optimal electrochemical response was obtained using the following square‐wave voltammetry parameters: f=250 Hz, E_sw=50 mV and E_s=2 mV using a Britton–Robinson buffer solution as electrolyte (pH 2). The detection and quantification limits determined for total N‐nitrosamines were 6.0×10^?8 and 2.0×10^?7 mol L^?1, respectively.     

Determination of Sulpiride by Linear Sweep Stripping Voltammetry at a Mercury Electrode

This paper reports the electrochemical properties of sulpiride at a mercury electrode,especially its adsorptive characteristic,Sulpiride dissolved in a supporting electrolyte of a McIlvaine buffer at pH 6.8 represents a sensitive and well defined reduction wave by linear sweep stripping voltammetry.This method is based on the pre-concentration and the reduction of sulpiride at a hung mercury drop electrode.The reduction peak potential is -1.72V(vs.Ag-AgCl) and the peak current is proportional to the concentration of sulpiride in the range of 0.1-0.6 μg/mL.The detection limit is 0.0250μg/mL obtained under the experimental conditions selected in this work.The electrochemical properties of this system were investigated.and the proposed method was applied to the determination of sulpiride in pharmaceutical tablets with satisfactory results,It was compared well with the UV spectrophotometric method,showing a superior sensitivity.