Determination of Trace Vanadium by Adsorptive Stripping Voltammetry at a Carbon Paste Electrode

A method for the voltammetric determination of vanadium using a carbon paste electrode (CPE) was described. The new procedure is based on the adsorptive accumulation of the V(V)‐alizarin red S(ARS) complex onto the surface of the CPE, followed by the electrochemical reduction of adsorbed species. The optimal experimental conditions include the use of 0.10 mol/L acetate buffer (pH 5.1), 1.0×10^?5 mol/L ARS, an accumulation potential of ?0.10 V (versus SCE), an accumulation time of 2 min, a scan rate of 200 mV/s and a second‐order derivative linear scan mode. The reduction peak for the complex appears at ?0.52 V. The peak current is proportional to the concentration of V(V) over the range of 0.10–15.0 μg/L, and the detection limit is 0.04 μg/L for a 2 min adsorption time. The relative standard deviations(n=8) for 2.0 and 0.50 μg/L V(V) are 3.1 and 4.7%, respectively. The proposed method was applied to the determination of vanadium in water samples.     

Adsorptive Voltammetry of Polyelectrolyte Complex Between 11‐Ferrocenyltrimethylundecylammonium and Polyanions at Carbon Paste Electrode

For polyelectrolyte complex between cationic surfactant and polyanion, the adsorptive voltammetry at carbon paste electrode using an electroactive cationic surfactant was examined. The adsorption state of the cationic surfactant in the complexes at CPE was estimated from the half‐height width of the oxidation waves. The half‐height width for poly(styrene sulfonate) was independent of the molecular weight, and was same as that for poly(vinyl sulfate). The half‐height width for heparin was broad and different from that of the vinyl polyanions. According to the analysis by Frumkin isotherm, the interaction between cationic surfactants was attractive in heparin complex at CPE, however, in the vinyl polyanion complexes at CPE the interaction was non‐cooperative as that predicted with the Langmuir isotherm. In spite of the same adsorption state, the concentration dependency of the peak current for poly(styrene sulfonate) was quite different from that for poly(vinyl sulfate). The concentration dependence indicated the reactive property of each polyanion on the association with the cationic surfactant in aqueous solution.     

奥美拉唑在碳糊电极上的吸附伏安测定法研究

研究了奥美拉唑在碳糊电极上的电化学行为及检测方法 ;在1.2mol·L -1H2SO4 底液中 ,通过富集用碳糊电极吸附伏安法测定奥美拉唑 ;阴极峰电位为0.403V(vsSCE) ,峰电流与奥美拉唑的浓度在7.8×10-8～3.7×10-5 mol·L-1 范围内呈良好的线性关系 ;该法的检出限为1.43×10-8 mol·L-1;用标准加入法测得回收率范围为94 %～102 % ;对奥美拉唑胶囊用该法进行了测定 ,获得了满意的结果 ;该法的优点是成本低 ,操作方便 ,重复性好及检出限较低 ;对电极响应机理进行了探讨 ,奥美拉唑的电极过程是一个两电子两质子的准可逆过程     

Determination of Trace Tin by Anodic Stripping Voltammetry at a Carbon Paste Electrode

A sensitive and selective procedure for the determination of trace tin at a carbon paste electrode was described. Each measurement cycle consisted of three steps: accumulation, reduction and stripping. The tin complex with bromopyrogallol red (BPR) was accumulated on the electrode surface in 0.10 mol/L acetate buffer (pH 4.5). After electrochemical reduction of Sn(II) had been carried out, the reoxidation wave of Sn(0) appeared at ?0.69 V (vs. SCE) on scanning the potential in the positive direction in 4.0 mol/L HCl. For a preconcentration time of 2 min, the detection limit was 0.06 μg/L (5×10^?10 mol/L ) and the linear range was from 0.1 to 50 μg/L. The proposed method was applied to the determination of tin in canned food and waste water samples with satisfactory results.     

痕量多巴酚丁胺在碳糊电极上的吸附伏安行为及其痕量测定的研究

在0.1mol/L H₂SO₄底液中,用碳糊电极吸附伏安法测定多巴酚丁胺,阳极峰电位为0.46V(υS.SCE),峰电流与多巴酚丁胺的浓度在3.0×10^-9～1.0×10^-6mol/L范围内呈良好的线性关系.该法检测下限为1.5×10^-9mol/L,回收范围为94.00%～102.59%,相对标准偏差为3.1%(n=9).本文还对反应机理进行了初步探讨.     

Indirect Determination of Trace Copper(II) by Adsorptive Stripping Voltammetry with Zincon at a Carbon Paste Electrode

Traces of copper(II) can be determined by adsorptive stripping voltammetry using 2‐carboxy‐2′‐hydroxy‐5′‐sulfoformazyl benzene (Zincon) as complex forming reagent. First in phosphate buffer pH 6.4, copper(II)‐Zincon complex was adsorbed on carbon paste electrode (CPE) with an accumulation potential of 0.6 V. Following this, adsorbed complex was oxidized and detected by differential pulse voltammetric (DPV) scan from 0.6 to 1.0 V. The effective parameters in sensor response were examined. The detection limit (DL) of copper(II) was 1.1 μg/L and relative standard deviations (RSDs) for 10 and 200 μg/L Cu(II) were 1.81 and 1.03%, respectively. The calibration curve was linear for 2–220 μg/L copper(II). The resulting CPE does not use mercury and therefore, has a positive environmental benefit. The method, which is reasonably sensitive and selective, has been successfully applied to the determination of trace amount of copper in water and human hair samples.     

靛红在碳糊电极上的阴极吸附伏安法研究

利用极谱分析仪,在0.40 mol/L的HAc-NaAc(pH 6.0)缓冲液中,发现靛红在碳糊电极(CPE)上有一灵敏的吸附伏安还原峰,峰电位为-0.44 V(vs.SCE)。该还原峰的二阶导数峰电流与靛红的浓度在4.0×10-8~1.0×10-7mol/L(富集90 s)范围内成良好的线性关系,相关系数为0.9954,检出限为8.0×10-9mol/L(S/N=3,富集110 s)。探讨了靛红在碳糊电极上的伏安性质和电极反应机理,并且成功应用于中草药青黛中靛红含量的测定。     

Determination of Trace Copper by Adsorptive Voltammetry Using a Multiwalled Carbon Nanotube Modified Carbon Paste Electrode

A new method for the determination of trace copper was described. A multiwalled carbon nanotube modified carbon paste electrode was prepared and the adsorptive voltammetric behavior of copper‐alizarin red S (ARS) complex at the modified electrode was investigated. By use of the second‐order derivative linear sweep voltammetry, it was found that in 0.04 mol/L acetate buffer solution (pH 4.2) containing 4×10^?6 mol/L ARS, when accumulation potential is 0 mV, accumulation time is 60 s and scan rate is 100 mV/s, the complex can be adsorbed on the surface of the electrode, yielding one sensitive reduction peak at ?172 mV (vs. SCE). The peak current of the complex is proportional to the concentration of Cu(II) in the range of 2.0×10^?11–4.0×10^?7 mol L^?1 with a detection limit (S/N=3) of 8.0×10^?12 mol/L (4 min accumulation). The proposed method was successfully applied to the determination of copper in biological samples with satisfactory results, the recoveries were found to be 96%–102%.     

碳糊电极吸附伏安法测定痕量锑的研究

利用液体石蜡作粘合剂制成ＣＰＥ，根据锑与茜素络合剂生成的络合物在ＣＰＥ上的吸附特性，考察了最佳底液条件，共存离子的影响，测定了电活性络合物的组成，探讨了电极反应机理。方法已用于水样中锑的测定，检出限为４＊１０＾－９ｍｏｌ／Ｌ。     

Determination of Trace Amount of Lead(II) in Sweet Fruit‐Flavored Powder Drinks by Differential Pulse Adsorptive Stripping Voltammetry at Carbon Paste Electrode

A new method is described for the determination of lead based on the cathodic adsorptive stripping of the lead–nuclear fast red (NFR) at a carbon paste electrode (CPE). The differential pulse voltammograms of the adsorbed complex of lead–NFR are recorded from ?0.10 to ?0.60 V (versus Ag/AgCl electrode). Optimal conditions were found to be an electrode containing 25% paraffin oil and 75% high purity graphite powder, 4.0×10^?5 mol L^?1 NFR; buffer solution (pH of 3.0), accumulation potential and time, ?0.20 V, 60 and 120 s (for high and low concentration of lead), respectively. The results show that the complex can be adsorbed on the surface of the CPE, yielding one peak at ?0.34 V, corresponding to reduction of NFR in the complex at the electrode. The detection limit was found to be 0.2 ng mL^?1 with a 120s accumulation time. The linear ranges are from 0.5 to 50 (t_acc=120 s) and 50 to 200 ng mL^?1 (t_acc=60 s). Application of the procedure to the determination of lead in lake water, bottled mineral water, synthetic samples and sweet fruit‐flavored powder drinks samples gave good results.     

Cyclic Voltammetry Examination for Effect of Counter Anion on Adsorptive Voltammetry of 11‐Ferrocenytrimethylundecylammonium at Carbon Paste Electrode

The electrode oxidation of 11‐ferrocenyltrimethylundecylammonium (FeTMUA) at carbon paste electrode (CPE) was investigated by cyclic voltammetry in order to reveal the adsorption nature of FeTMUA ion‐paired with anion. The voltammograms of FeTMUA were classified by the counter anion; hydrophilic and hydrophobic ions. The electric charge reflecting the adsorption isotherm increased gently with the FeTMUA concentration until a critical point (CP), which was independent of the sort of hydrophilic anion and comparable with the amount of the maximum surface coverage of FeTMUA at the air‐water interface. The voltammogram for hydrophobic anion had two oxidation waves. The electric charge for the first wave monotonously increased with the FeTMUA concentration without indicating CP. The second wave was not observed on the voltammogram at the glassy carbon electrode, thus the second wave was made from the pasting liquid. These results suggested that CPE adsorbed FeTMUA with hydrophilic anion behaved like serving a liquid surface, however, CPE adsorbed FeTMUA with hydrophobic anion was disordered and represented the heterogeneity.     

碳糊电极上吸附伏安法测定痕量钪的研究

研究了钪(Ⅲ) 茜素氨羧络合剂(ALC)络合物在碳糊电极正电位区的吸附伏安行为,利用该络合物产生的二次导数吸附氧化峰电流与钪浓度成正比测定钪。其线性范围为2.0×10-9～6.0×10-7mol/L;富集120s,检出限达1.0×10-9mol/L(S/N=3)。探讨了电极反应机理。在同一支电极同一表面上15次连续测定4.0×10-8mol/L的Sc(Ⅲ),方法的相对标准偏差为3.7%。该法用于矿石样品中钪的测定,结果满意。     

Adsorptive Stripping Voltammetry of Rifamycins at Unmodified and Surfactant‐Modified Carbon Paste Electrodes

The electrochemical behavior of the antibiotics rifampicin and rifamycin SV is investigated by cyclic voltammetry at carbon paste and in situ surfactant modified carbon paste electrodes. Both antibiotics adsorb on the unmodified electrodes and show a reversible redox process due to the oxidation of the 6,9‐dihydroxynaphthalene moiety to the corresponding naphthoquinone. This process is used as analytical signal for developing adsorptive voltammetric methods for the determination of the antibiotics. Experimental parameters, such as pH of the supporting electrolyte, accumulation potential and time are optimized. After accumulation from acidic solutions (0.1 M KCl pH 2 or HCl 0.2 M) at ?0.1 or 0 V for 3 min, the differential pulse oxidation peak current changes linearly with the antibiotic concentration in the range 3.5×10^?10 M ?5.4×10^?9 M or 5×10^?11 M ?1.0×10^?9 M for rifampicin and rifamycin SV, respectively. Rifamycin SV is not accumulated on carbon paste electrodes modified in situ with the anionic surfactant sodium dodecyl sulfate, whereas rifampicin is readily accumulated on this modified electrodes resulting in a signal enhancement and allowing rifampicin determinations without interference from rifamycin SV. On the other hand, selective determination of rifamycin SV in the presence of rifampicin is achieved by using carbon paste electrodes in situ modified with the cationic surfactant cetyltrimethylammonium chloride.     

茜素紫修饰碳糊电极阳极溶出伏安法测定痕量锡

研究了利用茜素紫修饰碳糊电极测定痕量锡的阳极溶出伏安法。在 0 1 5mol/L醋酸盐缓冲溶液 (pH 4 .8)中 ,通过开路富集 ,Sn 和茜素紫形成络合物富集于电极表面 ,然后经过介质交换至 3 0mol/L的盐酸溶液中 ,于 -0 .80V还原后再进行阳极化扫描 ,于 -0 .68V左右获得一灵敏的锡的溶出峰。二次导数峰电流与Sn 浓度在 8.4× 1 0 -9～ 1 .4× 1 0 -6mol/L范围内呈良好的线性关系。检出限达 4×1 0 -9mol/L ,同时对电极反应机理进行了讨论。     

秋水仙碱在碳糊电极上的吸附伏安行为

秋水仙碱在硫酸溶液中加热水解得分析试液。在０．０５ｍｏｌ／ＬＨ２ＳＯ４底液中，用碳糊电极吸附伏安法测定秋水仙碱，阳性峰电位为０．８２Ｖ（ｖｓ．ＳＣＥ），峰电流与秋水仙碱的浓度在１．０×１０＾－７～１．０×１０＾－４ｍｏｌ／Ｌ范围内呈良好线性关系，检测下限为５．０×１０＾－８ｍｏｌ／Ｌ回收范围为９５．０％～１０３．５％ＲＳＤ为２．８％（ｎ＝１０）。本对反应机理进行了初步探讨。     

Adsorptive Stripping Voltammetric Determination of Antimony by Using Alizarin Red S

Abstract

A sensitive and selective voltammetric method for determination of antimony(III) using Alizarin Red S (ARS) as complexing agent is described. The method is based on the monitoring the oxidation peak of antimony(III)-ARS complex at ?520 mV in ammonium-ammonia buffer (pH = 7.5). The peak current was measured by scanning the potential from ?700 mV versus Ag/AgClto more positive potentials without accumulation in the presence of 1 × 10^?6 mol L^?1 of ARS. The limit of detection (3 s) and limit of quantification (10 s) of the method were calculated from calibration curve as 1.45 µg L^? and 4.8 µg L^? respectively. The calibration plot for antimony(III) was linear in the range of 4.8–30 µg L^?. The interference of various ions was examined. Serious interference from Al(III), Fe(III), Cu(II), Pb(II), and Zn(II) was eliminated by addition of EDTA to the solution. The method was applied to drinking water samples. The recoveries were in the range 94% – 105%. The results obtained from the developed method were compared with those from the differential-pulse anodic-stripping method and no statistically significant difference was found.     

Stripping Voltammetry of Cerium(IIl) with a Chemically Modified Carbon Paste Electrode Containing Functionalized Nanoporous Silica Gel

This research introduces the design of an adsorptive stripping voltammetric method for the cerium(III) determination at a carbon paste electrode, chemically modified with dipyridyl‐functionalized nanoporous silica gel (DPNSG‐CPE). The electroanalytical procedure comprised two steps: the Ce(III) chemical accumulation at ?200 mV followed by the electrochemical detection of the Ce(III)/dipyridyl complex, using anodic stripping voltammetry. The factors, influencing the adsorptive stripping performance, were optimized including the modifier quantity in the paste, the electrolyte concentrations, the solution pH and the accumulation potential or time. The resulting electrode demonstrated a linear response over a wide range of Ce(III) concentration (1.0–28 ng mL^?1). The precision for seven determinations of 4 and 10 ng mL^?1 Ce(III) was 3.2% and 2.5% (relative standard deviation), respectively. The prepared electrode was used for the cerium determination in real samples and very good recovery results were obtained.     

碳糊电极阳极吸附伏安法测定卡托普利

在0.40 mol/L的HAc-NaAc(pH=4.8)缓冲溶液中,卡托普利(Captopril,CPT)在碳糊电极(CPE)上有一灵敏的吸附氧化峰,峰电位为0.23 V(vs.SCE)。该氧化峰的二阶导数峰电流与卡托普利的浓度在2.0×10-8～1.0×10-6mol/L(富集90 s)范围内呈良好的线性关系,相关系数为0.9966,检出限为8.0×10-9mol/L,并成功应用于卡托普利片含量的测定。探讨了卡托普利在碳糊电极上的伏安性质和电极反应机理。     

碳糊电极阳极吸附伏安法测定大黄酸

在pH4.2的HAc-NaAc底液中,大黄酸在碳糊电极(CPE)上有一灵敏的吸附氧化峰,峰电位为1.14V(vs.SCE)。该氧化峰的二阶导数峰电流与大黄酸的浓度在8.0×10-9~8.0×10-7mol/L(富集120s)范围内呈良好的线性关系(r=0.998),检出限为2×10-9mol/L(S/N=3,富集180s)。探讨了大黄酸在CPE上的伏安性质和电极反应机理,并将本法应用于中药大黄中的大黄酸的测定,结果良好。     

邻苯三酚红修饰碳糊电极吸附伏安法测定痕量铋

报道了采用邻苯三酚红修饰碳糊电极测定痕量铋的方法。在０．３０ｍｏｌ／Ｌ的ＨＣｌ溶液中,于－０．１０Ｖ搅拌富集３ｍｉｎ,然后在－０．３５Ｖ静止还原６０ｓ,再进行阳极化扫描,在－０．１０Ｖ左右获得灵敏的铋溶出峰,二次导数民流与铋浓度在１．０＊１０＾－９－６．０＊１０＾－７ｍｏｌ／Ｌ范围内呈线性关系,同限为５＊１０＾－１０ｍｏｌ／Ｌ。对电极反应机理进行了讨论。