Electro-deposition of platinum nanoparticles on 4-mercaptobenzene-functionalized multi-walled carbon nanotubes

A new method to electro-deposit platinum nanoparticles on the surface of multi-walled carbon nanotubes (MWNTs) functionalized with 4-mercaptobenzene has been described. X-ray photoelectron spectroscopy results reveal that 4-mercaptobenzene was attached to the surface of MWNTs. Transmission electron microscope and X-ray diffraction analysis confirm that platinum nanoparticles were highly dispersed on the surface of MWNTs, and the average size of the platinum particle is 4.2 nm. The electrocatalytic properties of the Pt/MWNT composite electrode for methanol oxidation were investigated by cyclic voltammetry, and the results show that the fabricated composites exhibit high catalytic activity and good long-term stability. The study provides a feasible approach to fabricate Pt/MWNT composite electrode for direct methanol fuel cell.     

Highly dispersed Pt nanoparticles immobilised on 3-amino-silane-modified MWNT materials for methanol oxidation

We demonstrate the use of molecular monolayers to enhance the nucleation of electrocatalytically active platinum nanocrystals onto carbon nanotubes. The multiwalled carbon nanotube (MWNT) is embedded within the polysiloxane shell with large amounts of hydrophilic amino groups outside after the siloxane is polymerized on the nanotube surfaces. Subsequent deposition of platinum nanoparticles led to high densities of 2- to 5-nm diameter Pt nanocrystals uniformly deposited along the length of the carbon nanotubes. The structure and nature of the resulting Pt/Si–MWNT composites were characterized by transmission electron microscopy and X-ray diffraction. Electrochemical measurements show that the molecular monolayers do not impede redox behavior of the electrode, and measurements of the electrocatalytic oxidation of methanol show very high catalytic efficiency.     

功能化碳纳米管表面高分散的钯纳米粒子在碱性溶液中的甲醇氧化行为

本工作中在水溶液体系中以芳烃重氮盐修饰的多壁碳纳米管(MWNT)为载体构筑了钯(Pd)纳米粒子碳纳米管复合结构。以MWNT的侧壁上C-C共价键接的氨基苯甲酸为沉积活化中心,制备了高分散高催化活性的钯(Pd)纳米粒子。结构成分和形貌分别用XRD和TEM表征。循环伏安(CV) 和交流阻抗的研究表明上述复合结构在碱性溶液中对甲醇的电催化氧化有很高的活性及稳定性。芳烃重氮盐修饰的MWNT是一种非常好的催化剂载体,而Pd-MWNT复合材料在燃料电池有着广泛的应用前景。     

High dispersion and electrocatalytic properties of platinum nanoparticles on graphitic carbon nanofibers (GCNFs)

Highly dispersed platinum nanoparticles were electrodeposited on graphitic carbon nanofibers (GCNFs) by cyclic voltammetry (CV) in 7.7 mM H2PtCl6+0.5 M HCl aqueous solutions. The graphitic carbon nanofibers (GCNFs) used in this paper were grown directly on a graphite disk by chemical vapor deposition (CVD). The micrographs and element composition of Pt/GCNFs/graphite electrode were characterized by scanning electron microscopy (SEM) and electron diffraction spectroscopy (EDS). The electrocatalytic properties of Pt/GCNFs/graphite electrode for methanol oxidation have been investigated by CV and excellent electrocatalytic activity can be observed even at very low platinum loading (md=8.79 microg cm(-2)). The highest mass activity (MA) for methanol oxidation reaches 323 Ag(-1) when Pt/GCNFs/graphite electrode was cycled at a sweep rate of 50 mVs(-1) by CV in 2 M CH3OH+1 M H2SO4 aqueous solutions. This may be attributed to the small particle size and high dispersion of platinum particles coated on GCNFs and shows good potential application in direct methanol fuel cell (DMFC). Additionally, the long-term cycling stability of platinum catalysts was also investigated.     

Electrocrystallized Ag nanoparticle on functional multi-walled carbon nanotube surfaces for hydrazine oxidation

4-Aminobenzoic acid was covalently grafted on multi-walled carbon nanotubes (MWNTs) by amine cation radical formation in the electrooxidation process of the amino-containing compound. Then, silver (Ag) nanoparticles were electrocrystallized on 4-aminobenzoic acid monolayer-grafted MWNTs by a potential-step method. The structure and nature of the resulting Ag/MWNT composites were characterized by transmission electron microscopy and X-ray diffraction. The electrocatalytic properties of the Ag/MWNT electrode for hydrazine oxidation have been investigated by cyclic voltammetry, high electrocatalytic activity of the Ag/MWNT electrode can be observed. This may be attributed to the small particle size of the silver particles. The results imply that the Ag/MWNT composites have a good application potential in fuel cells.     

Hollow carbon spheres with wide size distribution as anode catalyst support for direct methanol fuel cells

Hollow carbonaceous composites (HCCs) possessing sphere and hemisphere shape, which had wide size distribution between several tens of nanometers and several micrometers, were prepared through a facile hydrothermal method using glucose as carbon source with the assistance of sodium dodecyl sulfate (SDS). Pyrolysis of these hollow carbonaceous composites at 900 °C under nitrogen flow produced carbonized hollow carbon spheres (HCSs) without changing their structures. Platinum (Pt) was directly deposited on the surface of the HCSs by incipient wet method, using the NaBH₄ as the reductant. TEM, SEM, powder XRD and FT-IR were utilized to characterize all these samples. It was found that Pt nanoparticles were uniformly anchored on the outer and the inner surface of HCSs. The electrocatalytic properties of the Pt/HCS electrode for methanol oxidation have been investigated through cyclic voltammetry and chronoamperometry. The Pt/HCS electrode showed significantly higher electrocatalytic activity and more stability for methanol oxidation compared with Pt supported carbon microspheres (Pt/CMs) and commercial carbon (Pt/XC-72) electrode. The excellent performance for the Pt/HCS might be attributed to the high dispersion of platinum catalysts and the particular hollow structure of HCSs.     

Electrodeposition and electrocatalytic properties of platinum nanoparticles on multi-walled carbon nanotubes: effect of the deposition conditions

Platinum (Pt) nanoparticles were electrochemically deposited on multi-walled carbon nanotubes (MWCNTs) through a three-step process, including an electrochemical treatment of MWCNT, electro-oxidation of PtCl₄ ²⁻ to Pt(IV) complex, and an electro-conversion of Pt(0) on MWCNT. The effect of formation conditions for Pt(IV) complexes on the Pt nanoparticals transformed was investigated. The structure and elemental composition of the resulting Pt/MWCNT electrode were characterized by transmission electron micrograph (TEM) and energy dispersive X-ray spectroscopy (EDX). The electrocatalytic properties of the resulting Pt/MWCNT electrode for methanol oxidation have been investigated. The high electrocatalytic activity and good stability of Pt/MWCNT electrode may be attributed to the high dispersion of platinum nanoparticles and the particular properties of the MWCNT supports.     

Self‐Assembly of Platinum Nanoparticle/Multiwalled Carbon Nanotube Multilayer Film on Au Substrate Electrode

A novel approach to assemble multilayer films of Pt nanoparticle/multiwalled carbon nanotube (MWNTs) composites on Au substrate has been developed for the purpose of improving the methanol oxidation efficiency by providing high catalytic surface area. MWNTs were firstly functionalized with 4‐mercaptobenzene and then assembled on an Au substrate electrode. Pt nanoparticles were fabricated and attached to the surface of the functionalized MWNTs subsequently. Thus a layer of Pt/MWNT composites were assembled on the Au substrate electrode. Repeating above process can assemble different layers of film of Pt/MWNTs composites on the Au electrode. Cyclic voltammetry shows that the Au electrode modified with two layers of film of Pt/MWNT composites exhibits high catalytic ability and long‐term stability for methanol oxidation. The layer‐by‐layer self‐assembly technique provides an efficient strategy to construct complex nanostructure for improving the methanol oxidation efficiency by providing high catalytic surface area.     

乙二胺接枝改性碳纳米管负载的乙醇氧化电催化剂Pt及Pt-Ru的制备及电催化性质

采用化学法制备了乙二胺接枝改性碳纳米管（ED/MWNTs）负载的Pt及Pt-Ru催化剂,并用红外光谱法、透射电镜分析（TEM）及X射线能谱技术对催化剂进行了表征。结果表明：乙二胺对碳纳米管的改性使Pt及Pt-Ru在碳管上的分布更均匀,粒径更小。同时,催化剂对乙醇电催化氧化活性的电化学研究结果表明：乙二胺改性可明显提高Pt-Ru/MWNTs/C 和Pt/MWNTs/C的电催化活性,而且Pt/ED/MWNTs/C的活性甚至比Pt-Ru/MWNTs/C的活性还高。由此,ED/MWNTs作为乙醇电氧化催化剂的载体有着很好的应用前景。     

A simple one-step preparation of high utilization AuPt nanoparticles supported on MWCNTs for methanol oxidation in alkaline medium

A simple one-step preparation of gold–platinum electrocatalysts supported on multi-walled carbon nanotubes (MWCNTs) with high utilization is reported. A low Pt loading series of bimetallic AuPt/MWCNTs catalysts were prepared by the improved ethylene glycol reduction method, and then they were compared in terms of the electrocatalytic activity for methanol oxidation using cyclic voltammetry (CV) and chronoamperometry in alkaline solutions. The structure of AuPt/MWCNTs was characterized by the transmission electron microscopy (TEM), X-ray diffraction (XRD) and energy-dispersive X-ray spectroscopy (EDS). The results showed high Pt utilization, uniform AuPt nanoparticles size and good electrocatalytic activity for methanol electro-oxidation. The effect of Au/Pt mass ratio on electrocatalytic activity was also investigated by CV and chronoamperometry. The highest peak current density, lowest onset potential and best anti-poisoning effect for methanol electro-oxidation appeared at the Au/Pt/MWCNTs mass ratio of 2:4:32.     

Effect of the iridium oxide thin film on the electrochemical activity of platinum nanoparticles

The influence of the iridium oxide thin film on the electrocatalytic properties of platinum nanoparticles was investigated using the electro-oxidation of methanol and CO as a probe. The presence of the IrO(2) thin film leads to the homogeneous dispersion of Pt nanoparticles. For comparison, polycrystalline platinum and Pt nanoparticles dispersed on a Ti substrate in the absence of an IrO(2) layer (Ti/Pt) were also investigated in this study. Inverted and enhanced CO bipolar peaks were observed using an in situ electrochemical Fourier transform infrared technique during the methanol oxidation on the Pt nanoparticles dispersed on a Ti substrate. Electrochemical impedance studies showed that the charge transfer resistance was significantly lower for the Ti/IrO(2)/Pt electrode compared with that of the massive Pt and Ti/Pt nanoparticles. The presence of the IrO(2) thin film not only greatly increases the active surface area but also promotes CO oxidation at a much lower electrode potential, thus, significantly enhancing the electrocatalytic activity of Pt nanoparticles toward methanol electro-oxidation.     

Characterization of stainless steel electrode modified by a thin film of polyaniline containing pt particles and its electrocatalytic activity for methanol oxidation

The catalytic behavior of stainless steel (SS) electrode modified by a thin film of polyaniline (PANI) containing platinum particles was studied for electrooxidation of methanol and compared with a platinated Pt/PANI electrode in acidic aqueous solution. Cyclic voltammetry (CV), chronoamperometry, CO stripping techniques were used to investigate electrochemical properties and electrocatalytic activity of SS/PANI/Pt and Pt/PANI/Pt electrodes. The morphology and particle size of Pt catalysts were characterized by Transmission Electron Microscopy (TEM) measurement. The effects of various parameters such as thickness of polymer film, medium temperature and stability of the modified electrodes on methanol oxidation were also investigated. The results indicated that the modified SS electrode exhibited a considerably high electrocatalytic activity on the methanol oxidation as well as the modified Pt electrode.     

Synthesis of Ultrafine Mesoporous Tungsten Carbide by High‐energy Ball Milling and Its Electrocatalytic Activity for Methanol Oxidation

Ultrafine mesoporous tungsten carbide (WC) was prepared from as‐synthesized mesoporous WC using high‐energy ball milling treatment. X‐ray diffraction (XRD), scanning electron microscopy (SEM), and nitrogen adsorption‐desorption techniques were used to characterize the samples. Brunauer‐Emmett‐Teller (BET) surface areas of WC samples increased with the increasing ball milling time and kept constant at 10–11 m²·g^?1 for over 9 h. The electrocatalytic properties of methanol electro‐oxidation at WC powder microelectrodes were investigated by cyclic voltammetry, chronoamperometry, and quasi‐steady‐state polarization techniques. The results reveal that ball‐milled WC exhibits higher activity for methanol electro‐oxidation than as‐synthesized mesoporous WC. The suitability of ball‐milled WC for methanol electro‐oxidation is better than platinum (Pt) micro‐disk, although the current peak is not as high as the Pt micro‐disk. Moreover, increasing the methanol concentration and reaction temperature promotes methanol electro‐oxidation on ultrafine mesoporous WC.     

Controllable Electrodeposition of Platinum Nanoparticles on Graphene Nanosheet for Methanol Oxidation Reaction

A simple and cost-effective electrochemical method synthesized platinum nanoparticles on graphene nanosheet (PtNPs@GNS) is reported, and the Pt loading of the PtNPs@GNS can be controlled by electrodeposition. The structure and element analysis of the PtNPs@GNS have been investigated by scanning electron microscopy (SEM), Raman spectrum, X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS). The electrochemical measurement including electrochemical active surface area, current density, mass activity, oxidation peak potential,shows the PtNPs@GNS have more performance electrocatalytic properties for methanol oxidation reaction (MOR) compared to Vulcan XC-72 carbon (XC-72) supported PtNPs electrocatalysts. Probably, the cause which may be attributes to no aggregation of PtNPs and the well-dispersion on surface of GNS, so PtNPs@GNS show large electrochemically active surface area, highly electrocatalytic activity and stability in direct methanol fuel cells.     

Preparation of polyaniline–tin dioxide composites and their application in methanol electro-oxidation

Polyaniline–tin dioxide (PANI-SnO₂) composites were prepared by chemical polymerization method, and characterized by scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and X-ray diffraction. Due to the good stability in diluted acidic solution, PANI-SnO₂ composites were selected as the catalyst support and second catalyst for methanol electro-oxidation. The electrocatalytic properties of the PANI-SnO₂ supported Pt catalyst (Pt/PANI-SnO₂) for methanol oxidation have been investigated by cyclic voltammetry, chronoamperometry, and chronopotentiometry. Under the same loading mass of Pt, the Pt/PANI-SnO₂ catalyst shows higher electrocatalytic activity towards methanol electro-oxidation than Pt/SnO₂ catalyst.     

Enhanced Electrocatalytic Activity of Dual Template Based Pt/Cu‐zeolite A/Graphene for Methanol Electrooxidation

A novel Pt/Cu‐zeolite A/graphene based electrocatalyst was successfully prepared by chemical reduction method for methanol electrooxidation. Graphite oxide and Cu functionalized zeolite A were simultaneously reduced by NaBH₄ to prepare Cu‐zeolite A/graphene support which was used to deposit Pt nanoparticles. The nanostructure and composition of as‐prepared Pt/Cu‐zeolite A/graphene composites were characterized by X‐ray diffractometer, X‐ray fluorescence, Fourier transform infrared spectrometer and scanning electron microscopy. The electrocatalytic properties of Pt/Cu‐zeolite A/graphene modified electrode for methanol oxidation were investigated by cyclic voltammetry and chronoamperometry in 0.10 mol/L H₂SO₄ + 0.50 mol/L CH₃OH solution. Compared with Pt/zeolite A/graphene electrode and Pt/graphene electrode, Pt/Cu‐zeolite A/graphene based electrode exhibited obviously enhanced current and higher electrocatalytic activity for methanol electrooxidation. The increased electrocatalytic activity was attributed to the presence of zeolite A and reduced graphene oxide based dual template, which significantly increased the effective electrode surface and facilitated the diffusion of analytes into the electroactive catalyst.     

铂、钌共修饰碳纳米管电极的制备及对甲醇的电催化氧化

碳纳米管以其独特的结构,良好的电性能和机械性能吸引了众多的关注~([1]),被认为是潜在的异相催化剂载体 ~([2]).近来关于碳纳米管负载催化剂的合成及其在异相催化中应用的研究已见报道~([3]).     

Electrocatalytic oxidation of methanol on Pt/NiZn electrode in alkaline medium

In this study, a platinum electrode was coated with NiZn layer (Pt/NiZn) in a nickel-zinc bath by electrodeposition for use as anode material for methanol electrooxidation in alkaline solution. The electrode prepared was etched in a concentrated alkaline solution (30% NaOH) to produce a porous and electrocatalytic surface suitable for use in the methanol electrooxidation (Pt/NiZn). The surface morphologies and compositions of coating before and after alkaline leaching were determined by energy dispersive X-ray (EDX) and scanning electron microscopy (SEM) techniques. The effect of NiZn coated platinum electrode for methanol electrooxidation was investigated in 1 M NaOH solution by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques. Methanol electrooxidation on Pt/NiZn electrode was studied at various temperatures and potential scan rates. The results showed that Pt/NiZn electrode behaved as an efficient catalyst for the electrooxidation of methanol in alkaline medium.     

Electrocatalytic oxidation of methanol onto platinum particles decorated nanostructured poly (1,5-diaminonaphthalene) film

In this work, platinum particles decorated nanostructured poly (1,5-diaminonaphthalene) modified glassy carbon electrode (Pt/Nano-PDAN/MGCE) is prepared. The composite catalysts are characterized by scanning electron microscopy, energy dispersive spectroscopy, and electrochemical methods. The electrochemical methanol oxidation reaction is studied at the surface of this modified electrode. At same Pt loading, the Pt/Nano-PDAN/MGCE can act as higher efficient catalyst for methanol oxidation than that Pt/MGCE. Then, the influence of some parameters such as potential scan rates, switching potential, and methanol concentration on its oxidation as well as long-term stability of the modified electrode have studied by electrochemical methods. Also, ability of the modified electrode toward electrocatalytic oxidation of formaldehyde as an intermediate in methanol oxidation has been investigated.     

贵金属纳米颗粒在玻碳电极上的层层组装

采用表面活性剂二辛酯琥珀酸磺酸钠(AOT, sodiumbis(2-ethylhexyl)sulfosuccinate)微乳法可以制备得到各种贵金属纳米颗粒(包括银、金、铂以及钯),其性质利用紫外-可见吸收光谱、透射电镜、X-射线衍射、傅立叶变换红外光谱以及Zeta电位分析进行了表征。通过层层自组装方法,将带有负电荷的Pt纳米颗粒和聚阳离子(聚烯丙基氯化铵, PAH)自组装到玻碳电极上,并研究了该修饰电极对甲醇的电催化氧化性质。