Interpolymer complex between poly(ethylene oxide) and poly(carboxylic acid)

An interpolymer complex was prepared by mixing aqueous solutions of poly(ethylene oxide) (PEO) and of a poly(carboxylic acid), i.e., poly(acrylic acid)(PAA), poly(methacrylic acid)(PMAA), or styrene-maleic acid copolymer(PSMA). The complexation mechanism was discussed on the basis of results of such experimental methods as viscosity, potentiometric titration, and turbidimetry. The hydrogen bond is primarily involved in these complexations, but the influence of hydrophobic interaction on complexation can not be ignored. If the degree of dissociation α of carboxylic acid or the degree of polymerization P_n of PEO was perceptibly changed, a stable complex was obtained at about α 0.1 or P_n (PEO) = 40 for PMAA, 200 for PAA. This fact indicates that more than a definite number of binding sites are necessary for a stable interpolymer complex to be formed and that cooperative interaction among active sites plays an important role in complex formation.     

Interaction between poly (ethylene oxide) and silica nanoparticles in dilute solutions

A mixed system that includes poly(ethylene oxide) (PEO) and silica (SiO2) nanoparticles is prepared using two mixing methods. The interaction between PEO and the SiO2 nanoparticles in the dilute basic solution is investigated using the dynamic light scattering (DLS) and isothermal titration calorimetry (ITC) techniques. The DLS results show qualitatively that SiO2 nanoparticles interact with both random coils and aggregates of PEO through hydrogen bonding, and PEO-SiO2 complexes are formed. The degree of disaggregation of aggregates of PEO is readily adjusted by changing the concentration of SiO2 nanoparticle suspensions. Moreover, the ITC results also certify quantitatively the interaction between PEO and SiO2 nanoparticle, and give the evidence of formation of PEO-SiO2 complex.     

Crosslinkable interpolymer complexes of novolac resin and poly(ethylene oxide)

Crosslinkable interpolymer complexes of novolac resin and poly(ethylene oxide) (PEO) were prepared by mutual mixing ethanol solutions of novolac and PEO. Fourier transform infrared (FTIR) studies revealed that the driving force for the formation of novolac/PEO complex is hydrogen bonding interaction between the hydroxyl groups of novolac and the ether oxygens of PEO. The morphology and thermal properties of the complexes before and after curing were investigated by optical microscopy and differential scanning calorimetry (DSC). It was found that the uncured novolac/PEO complexes had a single composition-dependent glass transition temperature (T_g). The curing with 15 wt % hexamine (HMTA) (relative to novolac content) resulted in disappearing of T_g behaviour for both the neat novolac and the novolac-rich complexes, owing to less mobility of the novolac chain segments. The melting temperature (T_m) and crystallization rate of the HMTA-cured novolac/PEO complexes decreased with increasing novolac content, and no T_m was observed for the cured complexes with PEO content less than 50%. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36 : 401–411, 1998     

Copper sols stabilized by poly(ethylene glycol-600-monolaurate) and its complexes with poly(acrylic acid)

Copper sols stabilized by a polymer-colloid complex are studied via dynamic light scattering and transmission electron microscopy. It is shown that the polymer-colloid complex including poly(acrylic acid) and the nonionogenic polymeric surfactant poly(ethylene glycol-600-monolaurate) is an effective protector of copper nanoparticles formed via the reduction of Cu²⁺ ions in an aqueous medium. The sizes of sol particles of the nanocomposite consisting of the polymer-colloid complex and copper nanoparticles depend on the method of preparation of the nanocomposite. The incorporation of the copper nanoparticles being formed (an average diameter of 5 nm) into particles of the polymer-colloid complex leads to an insignificant change in the sizes of the complex particles. The same sizes are typical for particles of the nanocomposite formed during the introduction of surfactant micelles in the copper sol formed in the solution of poly(acrylic acid). The interaction of copper nanoparticles formed in an aqueous medium with surfactant micelles entails their aggregation; as a result, these nanoparticles turn out to be incorporated into large aggregates with equivalent radii of up to 100 nm. When poly(acrylic acid) is incorporated into this sol, the sizes of its particles insignificantly change apparently because of the low rate of structural rearrangements accompanying the formation of the polymer-colloid complex.     

Spin label study of phase morphology and polymer segmental motion in poly(acrylic acid)–poly(ethylene oxide) complex

The ESR lineshapes of nitroxide radical end‐labeled on poly(ethylene oxide) (SLPEO) for the pure polymer and for different weight ratio complexes with poly(acrylic acid) (PAA) were studied as a function of temperature. For SLPEO one spectral component was detected in the entire temperature range, indicating that the spin label was in the homogeneous phase domain. For all PAA–PEO complexes two spectral components with different rates of motion, a ‘fast’ and a ‘slow’ component, were observed, which indicates the existence of microheterogeneity at the molecular level: the more mobile the PEO‐rich microphase, the more rigid is the PAA‐rich microphase. On the other hand, the SLPEO polymer segmental motion was restricted owing to the hydrogen bond interaction between the carboxyl proton in PAA and the ether oxygen in PEO. This restriction was exacerbated with increasing the PAA content in the complex, which could be further substantiated through the calculated S and τ_c values. Copyright © 2003 John Wiley & Sons, Ltd.     

Mesoporous silica particles grafted with poly(ethyleneoxide‐block‐N‐vinylcaprolactam)

Mesoporous silica particles were grafted with thermoresponsive poly(ethyleneoxide‐b‐N‐vinylcaprolactam), PEO‐b‐PVCL. N‐vinylcaprolactam was first polymerized on particle surfaces using surface initiated atom transfer radical polymerization (SI‐ATRP) and then, the poly(ethyleneoxide) blocks were attached to the PVCL chain ends with click chemistry. The sizes, thermoresponsiviness, and colloidal stability of SiO₂‐PVCL and SiO₂‐PVCL‐b‐PEO particles and their aqueous dispersions were studied by scanning electron microscopy, turbidimetry, dynamic light scattering, zeta sizer, and microcalorimetry. The phase separation temperature of the PEO‐b‐PVCL grafted particles did not considerably differ from that of the SiO₂‐PVCL particles. The zeta potential of the grafted particles was close to zero at room temperature but decreased strongly upon heating. The decrease is related to the collapse of the PVCL blocks and correspondingly, the exposure of the silica surface toward the aqueous phase. The colloidal stability of the particles could be enhanced by adding PEO blocks to the chain ends of the PVCL grafts. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5012–5020     

Interaction of silicic acid with poly(1‐vinylimidazole)

Poly(1‐vinylimidazole) reacts with silicic acid and poly(silicic acid), giving rise to water‐soluble complexes and insoluble composites because of hydrogen bonding. The composition, structure, and morphology of the obtained products have been studied with elemental analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy. The main direction of the reaction depends not only on the initial ratio of the components, concentration, and pH but also on the sequence of the reagent mixing: the presence of poly(1‐vinylimidazole) macromolecules during the formation of silicic acid stabilizes soluble complexes, which precipitate with an excess of H₄SiO₄ only. These soluble complexes may serve as a pattern of particles responsible for the transport of silicic acid in diatom algae and other organisms that assimilate silicon from the environment. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 820–827, 2006     

Interaction of aluminum polyhydroxochloride sol and poly(4-vinylbenzene sulfonic acid) sodium salt

The interaction of aluminum polyhydroxochloride sol and poly(4-vinylbenzene sulfonic acid) sodium salt is studied. It is found that, in dilute aqueous solutions at pH 4.6, aluminum polyhydroxochloride sol and poly(4-vinylbenzene sulfonic acid) sodium salt form insoluble polymer-colloid complexes of steady compositions. Potentiometric titration data show that the interaction between particles of aluminum polyhy-droxochloride sol and linear macromolecules of the polyelectrolyte occurs via salt bonds formed between unlikely charged groups on the surface of particles and units of the linear polyelectrolyte. The composition of the polymer-colloid complex is determined, and the degree of conversion for the reaction of aluminum poly-hydroxochloride sol and poly(4-vinylbenzene sulfonic acid) sodium salt is estimated. The influence of various polyelectrolytes on the stability of the polymer-colloid complex is studied.     

Preparation and characterization of CuO/SiO2 and NiO/SiO2 with bimodal pore structure by sol-gel method

CuO/SiO₂ and NiO/SiO₂ with bimodal pore structure were prepared by sol-gel reactions of Tetra-methoxysilane (TMOS) and the respective metal nitrate in the presence of poly (ethylene oxide) (PEO) with an average molecular weight of 10 000 and the catalyst of acetic acid. In this process, the interconnected macroporous morphology was formed when transitional structures of spinodal decomposition were frozen by the sol-gel transition of silica. The addition of copper and nickel into the silica-PEO system had a negligible effect on the morphology formation. In gel formation, it was found that NiO crystalline sizes in the samples increased with decreasing Si/Ni molar ratio. It was considered that PEO interacted with both silica and nickel cations. In the CuO/SiO₂ with the presence of PEO_, CuO crystalline sizes were larger than those of NiO/SiO_2. It was considered that there was no obvious interaction between the Cu cation and PEO, most of the copper ions in wet silica gel were present in the outer solution. They easily aggregated as copper salts in the drying process of wet gel and decomposed into CuO particles in heating. While in the CuO/SiO₂ with the absence of PEO, the Cu was selectively entrapped as small particles in the gel skeleton due to the interaction between Cu aqua complex and silica gel network.     

Peculiarities of Formation of Intermolecular Polycomplexes Based on Polyacrylamide,Poly(vinyl alcohol) and Poly(ethylene oxide)

The phenomenon of self-assembly of aggregates formed by relatively short chains of poly(vinyl alcohol) (PVA) on the long macromolecules of polyacrylamide (PAA) in aqueous medium are discussed. PVA and PAA form intermolecular polycomplexes (InterPC) of a constant composition independently on a ratio of polymer components. The complex formation between high-molecular-weight PAA and relatively low-molecular-weight poly(ethylene oxide) (PEO) are considered also. PEO with M ⩽ 4·10⁴ g.mol⁻¹ weakly interacts with PAA. The polymer-polymer interaction can be intensified when the part of amide groups (∼20 mol %) on PAA chain to transform into the carboxylic groups. InterPCs formed by PEO and initial or modified PAA have associative structure with friable packing of the polymer segments. They are stabilized by the hydrogen bond system.     

A study of the composition of polyacrylamide-polyaluminum chloride polymer-colloid complexes

The behavior of aqueous solutions of polymer-colloid complexes based on polyacrylamide (M ～ 5.2 × 10⁵) and colloid particles of polyaluminum chloride depending on the initial component ratio and the concentration of a low-molecular-mass electrolyte (NaCl) was studied by means of viscometry and turbidimetry. It was suggested that the composition of polymer-colloid complexes, ? (the number of colloid particles attached to one macromolecule), depends on the component ratio. At ? > 1, the polymer-colloid complexes take on the polyelectrolyte properties, namely, repulsion in the case of overlap of the diffuse layers of counterions of colloid particles bound to the polymer chain leads to unfolding of macromolecular coils. Correspondingly, as the concentration of a low-molecular-mass salt increases, the coil size diminishes and the solubility of the complex drops. At ? = 1, the concentration of low-molecular-mass salt has no effect on the solubility of the complex and the viscosity of its solution.     

STUDIES OF THE CRYSTALLIZATION BEHAVIOR IN THE CRYSTALLINE/AMORPHOUS POLYMER BLENDS: POLY(ETHYLENE OXIDE)/POLY(METHYL METHACRYLATE) AND POLY(ETHYLENE OXIDE)/POLY(VINYL ACETATE)

The crystallization process of poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA)and PEO/poly(vinyl acetate) (PVAc) blends has been characterized by Fourier Transform Infrared(FTIR) spectra in conjunction with Differential Scanning Calorimeter (DSC) measurements. Thecrystallinity of PEO varies consistently with PEO content in PEO/PVAc blends and the PEO/PMMAblends containing 50 wt% or less PMMA. For the PEO/PMMA blends containing 60 wt% ormore PMMA, the crystallinity of PEO decreases more than PEO content but develops with crystal-lization time. These results can be explained in terms of difference between the crystallization tem-perature (T_c) and glass transition temperature (T_g) of the blends as a function of content of amorphouscomponent.     

Characterization of poly(carboxylic acid)/poly(ethylene oxide) blends formed through hydrogen bonding by spectroscopic and calorimetric analyses

The solid state of the complex between poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO), and that between poly(methacrylic acid) (PMAA) and PEO formed via hydrogen-bonding was studied by differential-scanning calorimetric (DSC) and by Fourier-transform infrared (FT–IR) spectroscopic measurements. Melting temperature T_m and the degree of the crystallinity X_c of PEO in the systems PAA (or PMAA)/PEO blends obtained from aqueous or dimethyl sulfoxide (DMSO) medium were measured in various unit mol % of PEO ([PEO]100/{[PAA(or PMAA)] + [PEO]}) where [ ] is the unit mole concentration. It was found that 50 unit mol % of PEO is a critical composition, which gives new evidence for the 1 : 1 complex formation between PAA (or PMAA) and PEO. From the FT–IR spectroscopic analysis in conjunction with DSC measurements we also found that the effects of solvent and of hydrophobic interaction (due to the α-methyl group of PMAA) are the important factors controlling the complexation in the solution and solid systems. These factors also affect the crystallization behavior and the microstructure of the PAA (or PMAA)/PEO blend in solid state.     

Crystallization kinetics of crosslinkable polymer complexes of novolac resin and poly(ethylene oxide)

Results of a study on the isothermal crystallization and thermal behavior of both uncured and hexamine-cured novolac/poly(ethylene oxide) (PEO) complexes are reported. The crystallization behavior of PEO in complexes is strongly influenced by factors such as composition, crystallization temperature, complexation, and crosslinking. The time dependence of the relative degree of crystallinity at high conversion deviated from the Avrami equation. The cured complexes exhibited an obvious two-stage crystallization (primary crystallization and crystal perfection), and this was more evident at higher crystallization temperature and high PEO-content. The addition of a noncrystallizable component into PEO caused a depression of both the overall crystallization rate and the melting temperature. In general, complexation and curing resulted in an increase in the overall crystallization rate. Complexation and curing are beneficial to the nucleation of PEO. Additionally, curing led to changes of the nucleation mechanism. Experimental data on the overall kinetic rate constant K_n were analyzed by means of the nucleation and crystal growth theory. For uncured complexes, the surface free energy of folding, σ_e, increased with increasing novolac content, whereas for cured complexes, σ_e displayed a maximum with the variation of composition. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2726–2736, 1999     

Synthesis and characterization of well-defined poly(methyl methacrylate)/CaCO3/SiO2 three-component composite particles via reverse atom transfer radical polymerization

The attempt to prepare structurally well-defined polymer/inorganic composite particles, i.e., poly(methyl methacrylate) (PMMA)/CaCO₃/SiO₂ three-component composite particles, via reverse atom transfer radical polymerization (ATRP), using 2-2′-azo-bis-isobutyronitrile as initiator and Cu(II) bromide as catalyst was reported. CaCO₃/SiO₂ two-component composite particles were first obtained through sol–gel method, and their morphology and surface element information were determined by transmission electron microscopy and X-ray photoelectron spectroscopy, respectively. The results indicate that the CaCO₃ was encapsulated by the obtained SiO₂. After being modified by silane coupling agent, the CaCO₃/SiO₂ composite particles copolymerized with methyl methacrylate (MMA) under standard reverse ATRP conditions to produce PMMA/CaCO₃/SiO₂ three-component composite particles. In the case concerned, first-order kinetic plots and linear increase of molecular weight (Mn) vs conversion and narrow molecular weight distribution for the graft polymer samples were observed. Furthermore, the gel permeation chromatography results illustrated that both the free PMMA chains from the solvent and the graft PMMA chains from the surface of CaCO₃/SiO₂ two-component composite particles were growing at the same rate. Characterizations of the PMMA-grafted CaCO₃/SiO₂ composite particles were done by Fourier transform infrared and thermogravimetric analysis. The results showed that the surface of the modified inorganic particles was grafted by the MMA and that the grafting percentage was about 8.7%.     

X-Ray absorption studies of NiBr2(PEO)8 and ErBr3(PEO)12 complexes

X-ray absorption studies of the poly(ethylene oxide) (PEO) complex NiBr₂(PEO)₈ show the formation of Br bridged dimers and higher aggregates. The Ni is complexed with Br and also with O atoms from the PEO. Aggregate formation increases with increasing temperature. In the case of ErBr₃(PEO)₁₂ the Er is simply complexed with Br and O. There is no evidence of aggregate formation.     

Interfacial effect on confined crystallization of poly(ethylene oxide)/silica composites

The impact of nanoconfinement introduced by nanoparticles on polymer crystallization has attracted extensive attention because it plays an important role in the ultimate properties of polymer nanocomposites. In this study, interfacial and spatial confinement effects of silica (SiO₂) nanoparticles on the crystallization behaviors of poly(ethylene oxide) (PEO)/SiO₂ composites were systematically investigated by changing the size and concentration of SiO₂ in PEO matrix. The composites with high silica loadings exhibit two crystallization peaks of PEO as determined by differential scanning calorimetry. The first peak at 7–43 °C is related to the bulk PEO, while the second peak at ?20 to ?30 °C is attributed to the restricted PEO segments. Three‐layer (amorphous, interfacial, and bulk) model is proposed to interpret the confined crystallization of PEO/SiO₂ composites, which is supported by the results of thermogravimetric analysis and solid‐state ¹H nuclear magnetic resonance. In amorphous layer, most PEO segments are directly adsorbed on SiO₂ surface via hydrogen bonding. The interfacial PEO layer, which is nonuniform, is composed of crystallizable loops and tails extending from amorphous layer. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 414–423     

Lamellar structure of poly(ethylene oxide) molecular complexes

The phase diagrams of some binary systems such as poly(ethy lene oxide)-p-dihalogenobenzene, poly(ethylene oxide)-resorcinol and poly(ethylene oxide)-p-nitrophenol show the existence of molecular complexes with a well definite stoichiometry. The crystal structure of these molecular complexes has been determined by wide-angle X-ray diffraction. The morphology of these molecular complexes crystallized from the melt is investigated by differential scanning calorimetry and small angle X-ray scattering. PEO-p-dichlorobenzene and PEO-resorcinol complexes crystallize from the melt as extended chains (EC) or integral folded chain (IFC) lamellar crystals. As observed for PEO oligomers, the fraction of EC crystals of PEO-resorcinol increases with the crystallization temperature. However EC crystals are present in a larger range of crystallization temperatures than for pure PEO. On the other hand, the PEO-p-nitrophenol complex crystallizes over all the studied crystallization temperature range as stable non integral folded chain (NIFC) crystals. Explanations related to the crystal structure of these complexes and to their mode of growth are invoked to explain these two deeply different lamellar morphologies.     

Preparation of nanoparticles of double‐hydrophilic PEO‐PHEMA block copolymers by AGET ATRP in inverse miniemulsion

Atom transfer radical polymerization with activators generated by electron transfer initiating/catalytic system (AGET ATRP) of 2‐hydroxyethyl methacrylate (HEMA) was carried out in inverse miniemulsion. Water‐soluble ascorbic acid as a reducing agent and mono‐ and difunctional poly(ethylene oxide)‐based bromoisobutyrate (PEO‐Br) as a macroinitiator were used in the presence of CuBr₂/tris[(2‐pyridyl)methyl]amine (TPMA) and CuCl₂/TPMA complexes. The use of poly(ethylene‐co‐butylene)‐block‐poly(ethylene oxide) as a polymer surfactant resulted in the formation of stable HEMA cyclohexane inverse dispersion and PHEMA colloidal particles. All polymerizations were well‐controlled, allowing for the preparation of well‐defined PEO‐PHEMA and PHEMA‐PEO‐PHEMA block copolymers with relatively high molecular weight (DP > 200) and narrow molecular weight distribution (M_w/M_n < 1.3). These block copolymers self‐assembled to form micellar nanoparticles being 10–20 nm in diameter with uniform size distribution, and aggregation number of ～10 confirmed by atomic force microscopy and transmission electron microscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4764–4772, 2007     

Nonlinear Effects on the Ionic Conductivity of Polyethylene Oxide)/Uthium Perchlorate Complexes Caused by the Blending of Polyvinyl Acetate)

Poly(ethylene oxide) (PEO)/LiClO₄/poly(vinyl acetate) (PVAc) and PEO/LiClO₄/poly(vinyl pyrrolidone) (PVP) complexes were prepared with various weight ratios of PVAc and PVP to PEO. The conductivity (σ) of the PEO/LiClO₄ complex was increased in a nonlinear fashion by the presence of up to 60 wt% PVAc. PEO/LiClO₄/PVAc complexes with weight percents of PVAc greater than 60 had σ's less than that of PEO/LiClO₄. The σ of PEO/LiClO₄ was decreased by the presence of any PVP.