含负折射率材料一维光子晶体的全方位带隙和缺陷模

运用光学传输矩阵理论,研究了含负折射率材料一维二元光子晶体的禁带特性和局域模特性,发现了一种新型全方位光子带隙.与传统的Bragg带隙相比,这种新型全方位光子带隙的中心频率和带宽对入射角的变化不敏感.讨论了引入缺陷层后,入射角变化和各层介质厚度做一定比例的缩放时对缺陷模位置的影响.这种特性在具有固定带宽的全方位反射器和微波技术中全方位或大入射角滤波器方面有重要的应用价值.     

异质三周期光子晶体的光子带隙特性

利用传输矩阵法研究了由TiO₂和SiO₂两种材料构成的异质三周期一维光子晶体的传光特性,发现该结构能在波长为200~ 2 000 nm的范围内形成7处比较明显的光子带隙,并且波长越大,带隙的宽度越大。重点研究了这种结构的光子晶体的透射谱线与入射角度、介质层数及介质层厚度的关系,发现该结构形成的光子带隙的大小和位置对介质层的循环周期数不敏感,但对入射角度和介质层的厚度很敏感。     

一维光子晶体缺陷模的偏振特性研究

利用周期结构的布洛赫定理推导了一维无限光子晶体缺陷模方程,研究了缺陷模的偏振特性,以及在不同入射角和缺陷层厚度下缺陷模位置的变化.利用传输矩阵方法对有限周期数光子晶体也进行了研究,分别对应一维无限光子晶体和有限周期数光子晶体给出了数值计算结果.通过比较这两者的数值结果得出了缺陷模随入射角和缺陷层厚度变化的一般规律.     

光子晶体多通道可调谐偏振滤波器的理论研究

通过对设计的一维掺杂光子晶体的数值计算和理论分析,得出了两个偏振态缺陷模透射峰的变化特征为:P-偏振波其缺陷模透射峰在入射角大于0.75(rad)范围内有多条明显的缺陷模透射峰带,而S-偏振波在入射角大于0.75 (rad) 范围内没有缺陷模透射峰;P-偏振波缺陷模在同一杂质光学厚度可以截到多个波长不同的透射峰.以此为基础设计出滤波通道波长可调范围大于60 nm 、滤波通道的半高宽可调范围在1~5 nm、滤波通道透射峰值大于0.98的一维光子晶体三通道可调谐偏振滤波器.     

基于含单负材料光量子阱结构的全向多通道滤波器

分析了含单负材料的光量子阱结构中的振荡透射模的性质.用两种单负(负介电常量或负磁导率)材料交替周期堆叠形成的两个光子晶体构造了一维光量子阱结构,该结构中仅其中一个光子晶体含有零有效位相带隙.数值计算结果发现,在零有效位相带隙内存在振荡透射模.通过改变井区域光子晶体内单负材料层的厚度及周期数,振荡透射模的数目、频率及频率间隔均可调节.振荡透射模对入射角度的依赖均很弱;随着入射角度的改变,缺陷模频率的相对改变量保持在0.02以下.该研究结果可用于设计多通道全向滤波器.     

基于含单负材料光量子阱结构的全向多通道滤波器

分析了含单负材料的光量子阱结构中的振荡透射模的性质.用两种单负（负介电常量或负磁导率）材料交替周期堆叠形成的两个光子晶体构造了一维光量子阱结构,该结构中仅其中一个光子晶体含有零有效位相带隙.数值计算结果发现,在零有效位相带隙内存在振荡透射模.通过改变井区域光子晶体内单负材料层的厚度及周期数,振荡透射模的数目、频率及频率间隔均可调节.振荡透射模对入射角度的依赖均很弱;随着入射角度的改变,缺陷模频率的相对改变量保持在0.02以下.该研究结果可用于设计多通道全向滤波器.     

数值研究含有负折射率材料的一维光子晶体的带隙特性

由修正后的传输矩阵理论研究了由单负材料构成的一维光子晶体的带隙特性。发现了此结构的光子晶体中同时存在着全方位带隙和布拉格带隙,且发现A、B层厚度等比例变化时全方位带隙非常稳定;当引入缺陷时,全方位带隙里的缺陷态将随入射角度、A层和B层同比例缩放的变化相对稳定,而布拉格带隙里的缺陷态在频谱域内变化很大。     

色散光子晶体GHz波段的传输特性

将两单负材料耦合后,再与一双负材料交替生成光子晶体。然后利用传输矩阵法对该光子晶体的能带和缺陷模进行了研究。结果表明:这种结构的光子晶体具有一种新型的光子带隙,不随晶格常数的缩放而移动;当引入普通电介质缺陷层时,缺陷模对入射角的改变不敏感,但缺陷模个数随着缺陷层厚度的增加而增多。     

异质镜像光子晶体的光子带隙研究

对异质镜像结构光子晶体(ABCCBA)^N进行了研究。首先,利用一维介电体系中处理光传播的方法--传输矩阵法,详细推导了异质镜像光子晶体透射率的计算公式;然后,采用Matlab软件编程仿真并分析了光子带隙形成与镜像周期数目、光子带隙数目与光子晶体薄层厚度、光子带隙位置与入射角大小等的关系。结果表明:光子带隙的形成及变化主要受光子晶体薄层厚度及入射角大小变化的影响。通过改变影响光子晶体光子带隙的参数,可得到不同频段的光子带隙,用来制作高质量反射镜、滤波器和发光二极管等。     

异质单周期内对称光子晶体的光子带隙特性

利用传输矩阵法,理论上对由TIO₂和SiO₂构成的异质单周期内对称光子晶体的透射谱进行仿真,分别改变入射光的角度、光子晶体介质层数和BA两层的厚度比,观察其透射谱,研究发现该结构形成的光子带隙的位置大小对介质层数的变化不敏感,但对入射角和BA两层厚度比的变化很敏感,这一研究对于光子晶体的设计具有重要意义.     

Properties of Defect Modes in Periodic Lossy Multilayer with Negative-Index-Materials

Employing the characteristic matrix method, this study investigates transmission properties of onedimensional defective lossy photonic crystals composed of negative and positive refractive index layers with one lossless defect layer at the center of the crystal. The results of the study show that as the refractive index and thickness of the defect layer increase, the frequency of the defect mode decreases. In addition, the study shows that the frequency of the defect mode is sensitive to the incidence angle, polarization, and physical properties of the defect layer, but it is insensitive to the small lattice loss factor. The peak of the defect mode is very sensitive to the loss factor, incidence angle, polarization, refractive index, and thickness of the defect layer. This study also shows that the peak and the width of the defect mode are affected by the numbers of the lattice period and the loss factor. The results can lead to designing new types of narrow filter structures and other optical devices.     

一维准周期光子晶体缺陷模特性研究

利用传输矩阵法,计算了含缺陷层的一维准周期光子晶体在入射角为0°和10°时的透射谱,并将其和对应的含缺陷层的周期光予晶体的透射谱进行了对比。结果表明：在上述入射角的情况下,当缺陷层介质的厚度为四分之一波片层的整数倍M时,通带中新增缺陷模的个数仍满足M-1的关系,但准周期光子晶体的透射谱散失了原来的左右对称性;当M取非整数时,中心通带顶部由原来的三峰状变成双峰状。     

Defect modes properties in periodic lossy multilayer containing negative index materials with symmetric and asymmetric geometric structures

In this paper, the characteristic matrix method is used to study the propagation of electromagnetic waves through one-dimensional lossy photonic crystals composed of negative and positive refractive index material layers with symmetric and asymmetric geometric structures with a defect layer at the center of the structure. First, the positive index material defect layer is considered, and the effects of the polarization and the angle of incidence on the defect mode in the transmission spectra of the both structures are investigated. The results show that the number of the defect modes in the transmission spectra depends on the geometry (symmetric or asymmetric) of the structure. In addition, it is shown that the defect mode frequency increases as the angle of incidence increases. This property is independent of the geometry of the structure. Then, for normal incidence, the negative index material defect layer is considered, and the properties of defect modes for both structures are investigated. The results can lead to designing new types of transmission narrow filters.     

Near-infrared tunable narrow filter properties in a 1D photonic crystal containing semiconductor metamaterial photonic quantum-well defect

The near-infrared (NIR) narrow filter properties in the transmission spectra of a one-dimensional photonic crystal doped with semiconductor metamaterial photonic quantum-well defect (PQW) were theoretically studied. The behavior of the defect mode as a function of the stack number of the PQW defect structure, the filling factor of semiconductor metamaterial layer, the polarization and the angle of incidence were investigated for Al-doped ZnO (AZO) and ZnO as the semiconductor metamaterial layer. It is found that the frequency of the defect mode can be tuned by variation of the period of the defect structure, polarization, incidence angle, and the filling factor of the semiconductor metamaterial layer. It is also shown that the number of the defect mode is independent of the period of the PQW defect structure and is in sharp contrast with the case where a common dielectric or metamaterial defect are used. The results also show that for both polarizations the defect mode is red-shifted as the number of the defect period and filling factor increase. An opposite trend is observed as the angle of incidence increases. The proposed structure could provide useful information for designing new types of tuneable narrowband filters at NIR region.     

RTCM算法在一维光子晶体缺陷模中的应用

利用RTCM算法研究一维光子晶体的缺陷模.研究了TE波和TM波入射时的情况,通过改变杂质层的光学厚度以及杂质层的折射率从而得出一些有重要指导意义的缺陷模特性.同时对有缺陷的一维光子晶体在窄带滤波器中的应用做了一定程度的探讨.结果表明:正入射时,TE波和TM波的透射率几乎相同,随着杂质层光学厚度的增加,透射峰数目增加,这有助于制作多道窄带滤波器.因此,有缺陷的一维光子晶体可以制作波分复用中的多道滤波器.     

各向异性圆柱掺杂光子晶体的缺陷模及其量子效应

利用光波在一维各向异性圆柱掺杂光子晶体中径向受限的条件,研究了光波在其中出现的模式量子效应,并利用特征矩阵法计算了TE波和TM波各模式的缺陷模的变化规律,得出了一些一维各向异性圆柱光子晶体缺陷模的新结构.缺陷模的频率和透射角都随模式量子数的增加而增大.同一模式缺陷模的频率随圆柱半径的增加而减小. 关键词： 圆柱光子晶体 各向异性介质 量子效应 缺陷模     

The effect of random variations of structure parameters on photonic band gaps of one-dimensional plasma photonic crystals

The electromagnetic properties of one-dimensional plasma photonic crystals influenced by random perturbation of structure parameters are studied through transfer matrix method in the paper. The random perturbation of thicknesses of layers as well as plasma frequency of layers can influence the electromagnetic properties of one-dimensional plasma photonic crystal. The random perturbation of thicknesses of layers tremendously impacts the band structure of one-dimensional plasma photonic crystals in high frequency domain. The random perturbation of plasma frequency, however, contributes to the moving of a cutoff frequency in the low frequency domain. The position of the defect mode of one-dimensional plasma photonic crystal randomly moves due to the random perturbations. The effect of random perturbation of plasma frequency is more significant than that of random perturbation of thickness of layers, which alters not only the transmittance but also the position of the defect mode. An improved quality factor and a shortened moving distance of the defect mode are both acquired by increasing the period number. And then this work may provide a crude but useful instrument in analyzing disordered 1DPPCs.