Long RE123 coated conductors with high critical current over 500 A/cm by IBAD/PLD technique

We have developed long RE₁Ba₂Cu₃O_7?X (RE123) coated conductors with large current capacity by the ion beam assisted deposition (IBAD) and the pulsed laser deposition using hot wall heating (HW-PLD) technique. As a result, we could fabricate an 8 m-long Gd₁Ba₂Cu₃O_7?X (Gd123) coated wire with the minimum and maximum critical current (I_c) of 951 A/cm-w and 1003 A/cm-w at 77 K, 0 T, respectively, measured in 0.7 m-long sections by the standard 4-probe technique. Furthermore, we succeeded in preparation of over 600 m-long Gd123 coated wire with the uniform I_c distribution over 600 A/cm-w. It had average, maximum and minimum I_c of 665, 698, 609 A/cm-w, respectively. The n-values of the sample showed the maximum I_c and minimum I_c were 40 and 36, respectively. As a result, we set the new world record of I_c × L value as 374535 A m (= 609 A × 615 m). The in-field performance of this long wire was quite high as well; the minimum I_c exceeded 50 A/cm-w at 77 K, 3 T.     

Thickness dependence of Ic and Jc of LTG-SmBCO coated-conductor on IBAD-MgO tapes

We have reported SmBa₂Cu₃O_y (SmBCO) films on single crystalline substrates prepared by low-temperature growth (LTG) technique. The LTG-SmBCO films showed high critical current densities in magnetic fields compared with conventional SmBCO films prepared by pulsed laser deposition (PLD) method. In this study, to enhance critical current (I_c) in magnetic field, we fabricated thick LTG-SmBCO films on metal substrates with ion-beam assisted deposition (IBAD)-MgO buffer and estimated the I_c and J_c in magnetic fields.All the SmBCO films showed c-axis orientation and cube-on-cube in-plane texture. T_c of the LTG-SmBCO films were 93.1–93.4 K. J_c and I_c of a 0.5 μm-thick SmBCO film were 3.0 MA/cm² and 150 A/cm-width at 77 K in self-field, respectively. Those of a 2.0 μm-thick film were 1.6 MA/cm² and 284 A/cm-width respectively. Although I_c increased with the film thickness increasing up to 2 μm, the I_c tended to be saturated in 300 A/cm-width. From a cross sectional TEM image of the SmBCO film, we recognized a-axis oriented grains and 45° grains and Cu–O precipitates. Because these undesired grains form dead layers, I_c saturated above a certain thickness. We achieved that I_c in magnetic fields of the LTG-SmBCO films with a thickness of 2.0 μm were 88 A/cm-width at 1 T and 28 A/cm-width at 3 T.     

Tunable supercurrent in superconductor/normal metal/superconductor Josephson junctions

When two superconductors are connected by a weak link a supercurrent flows determined by the difference in the macroscopic quantum phases of the superconductors. Originally, this phenomenon was discovered by Josephson for the case of a weak link formed by a thin tunnel barrier. The supercurrent I is related to the phase difference ϕ through the Josephson current–phase relation, I = I_csin ϕ, with I_c, the critical current, depending on the properties of the weak link. A similar relation holds for weak links consisting of a normal metal, a semiconductor or a constriction . In all cases, the phase differenceϕ =  0 when no supercurrent flows through the junction, and ϕ increases monotonically with increasing supercurrent until the critical current is reached. Using nanolithography techniques we have succeeded in making and studying a Josephson junction with a normal metal weak link, in which we have direct access to the microscopic current-carrying states inside the link. We find that the fundamental Josephson relation can be changed fromI = I_csin ϕ toI = I_csin(ϕ + π), i.e. to a π -junction, by suitably controlling the energy distribution of the current-carrying states in the normal metal. This fundamental change in the way these Josephson junctions behave has potential implications for their use in superconducting electronics as well as (quantum) logic circuits based on superconductors.     

Effect of the composition on the superconducting properties of IBAD-MgO SmBCO coated conductors with superconducting film directly deposited on epi-MgO layer

Sm_1+xBa_2?xCu_3+yO_7?δ (SmBCO) films were directly deposited on the epi-MgO/IBAD-MgO/Y₂O₃/Al₂O₃/Hastelloy template by co-evaporation using the evaporation using drum in dual chambers (EDDC) system without the buffer layer in order to investigate the effect of the composition ratios on superconducting property, microstructure and texture of SmBCO film. The films with gradient composition ratios of Sm:Ba:Cu were deposited using a shield with an opening which was placed between the substrate and the boats. The highest I_c of 52 A (corresponding to J_c = 1.6 MA/cm² and a thickness of 800 nm) was observed at 77 K in self field at a composition x = 0.01–0.05 and y = ?0.23 to ?0.46. When the composition ratio is outside this range, the I_c value rapidly decreased. The superconducting critical current was highly dependent on the composition ratio. As the composition ratio is farther away from that of the highest I_c, the SmBCO (1 0 3) peak intensity increased and the amount of a-axis oriented parts increased. A dense microstructure with round-shape grains was observed in the region showing the highest I_c. The optimum composition ratio can be found by analyzing films deposited with variable deposition rates of each depositing element.     

Large transport critical currents of powder-in-tube Sr0.6K0.4Fe2As2/Ag superconducting wires and tapes

We report the achievement of transport critical currents in Sr_0.6K_0.4Fe₂As₂ wires and tapes with a T_c = 34 K. The wires and tapes were fabricated through an in situ powder-in-tube process. Silver was used as a chemical addition as well as a sheath material. All the wire and tape samples have shown the ability to transport superconducting current. Critical current density J_c was enhanced upon silver addition, and at 4.2 K, a largest J_c of ～1200 A/cm² (I_c = 9 A) was achieved for 20% silver added tapes, which is the highest in iron-based wires and tapes so far. The J_c is almost field independent between 1 T and 10 T, exhibiting a strong vortex pinning. Such a high transport critical current density is attributed to the weak reaction between the silver sheath and the superconducting core, as well as an improved connectivity between grains. We also identify a weak-link behavior from the apparent drop of J_c at low fields and a hysteretic phenomenon. Finally, we found that compared to Fe, Ta and Nb tubes, Ag was the best sheath material for the fabrication of high-performance 122 type pnictide wires and tapes.     

Influence of Zr and Ce doping on electromagnetic properties of (Gd,Y)–Ba–Cu–O superconducting tapes fabricated by metal organic chemical vapor deposition

(Gd,Y)Ba₂Cu₃O_x tapes have been fabricated by metal organic chemical vapor deposition (MOCVD) with Zr-doping levels of 0–15 mol.% and Ce doping levels of 0–10 mol.% in 0.4 μm thick films. The critical current density (J_c) of Zr-doped samples at 77 K, 1 T applied in the orientation of H 6 c is found to increase with Zr content and shows a maximum at 7.5% Zr doping. The 7.5% Zr-doped sample exhibits a critical current density (J_c) of 0.95 MA/cm² at H 6 c which is more than 70% higher than the J_c of the undoped sample. The peak in J_c at H 6 c is 83% of that at H 6 a–b in the 7.5% Zr-doped sample which is more than twice as that in the undoped sample. Superconducting transition temperature (T_c) values as high as about 89 K have been achieved in samples even with 15% Zr and 10% Ce. Ce-doped samples with and without Ba compensation are found to exhibit substantially different J_c values as well as angular dependence characteristics.     

Intrinsic pinning properties of FeSe0.5Te0.5

The intrinsic pinning properties of FeSe_0.5Te_0.5, which is a superconductor with a critical temperature T_c of approximately 14 K, were studied through the analysis of magnetization curves obtained using an extended critical state model. For the magnetization measurements carried out with a superconducting quantum interference device (SQUID), external magnetic fields were applied parallel and perpendicular to the c-axis of the sample. The critical current density J_c under the perpendicular magnetic field of 1 T was estimated using the Kimishima model to be equal to approximately 1.6 × 10⁴, 8.8 × 10³, 4.1 × 10³, and 1.5 × 10³ A/cm² at 5, 7, 9, and 11 K, respectively. Furthermore, the temperature dependence of J_c was fitted to the exponential law of J_c(0) × exp(?αT/T_c) up to 9 K and the power law of J_c(0) × (1 ? T/T_c)ⁿ near T_c.     

Pinning,thermally activated depinning and their importance for tuning the nanoprecipitate size and density in high Jc YBa2Cu3O7−x films

YBa₂Cu₃O_7?x (Y123) films with quantitatively controlled artificial nanoprecipitate pinning centers were grown by pulsed laser deposition (PLD) and characterized by transport over wide temperature (T) and magnetic field (H) ranges and by transmission electron microscopy (TEM). The critical current density J_c was found to be determined by the interplay of strong vortex pinning and thermally activated depinning (TAD), which together produced a non-monotonic dependence of J_c on c-axis pin spacing d_c. At low T and H, J_c increased with decreasing d_c, reaching the very high J_c ～ 48 MA/cm² ～20% of the depairing current density J_d at 10 K, self-field and d_c ～ 10 nm, but at higher T and H when TAD effects become significant, J_c was optimized at larger d_c because longer vortex segments confined between nanoprecipitates are less prone to thermal fluctuations. We conclude that precipitates should extend at least several coherence lengths along vortices in order to produce irreversibility fields H_irr(77 K) greater than 7 T and maximum bulk pinning forces F_p,max(77 K) greater than 7–8 GN/m³ (values appropriate for H parallel to the c-axis). Our results show that there is no universal pin array that optimizes J_c at all T and H.     

Current carrying capability of HTS Roebel cable

We have developed a numerical technique to estimate the current carrying capability of HTS Roebel cable composed from coated conductor strands. The influence of self-field on the critical current density is studied computationally for a Roebel cable using a realistic field and angle dependence behaviour of critical current. The computations are carried out for N/2 (number of strands/strand width in mm), and N/5 Roebel cable for N = 2–15. The local current distribution in each strand satisfies the self-consistent criteria J = J_c(B(J)) except for a small region where the current density is set to zero to maintain the condition of equal currents in all strands. The variation of critical current with vertical and horizontal separation between the strands is also investigated. Results are compared with the measured values of critical current for some of our cables. The comparison shows an error of up to 10% which we attribute mostly to the model not accounting for the spread in I_c values of the constituent strands.     

I–V characteristics and magnetic field profile studies in high Tc BSCCO based Helmholtz coil

A double pancake wound high T_c Helmholtz coil has been fabricated using commercial grade BSCCO tape. The current voltage (I–V) characteristics of this HTS coil has been carried out using standard four probe technique. From the I–V characteristics, the critical current based on self field dependent of HTS coil and quality index “n” value have been calculated. Magnetic field profiles have been studied along the axis of this coil for various amplitudes of applied current ranging from 10 A to 50 A at 77 K. The measured field profiles have a very good agreement with that of theoretical values predicted in the literature.     

Aqueous polymer–nitrate solution deposition of YBCO films

High critical current density YBa₂Cu₃O_7?x (YBCO) films were prepared by solution deposition of aqueous non-fluorine precursors. Non-fluorine polymer-assisted deposition (PAD) processes utilizing rheology modifiers and chelating agents were used to produce 50 nm films with a critical current density (J_c) over 3 MA/cm² and 400 nm films with J_c > 1 MA/cm²_. T_c measurements indicated that films have T_c values near 90 K. The total heat treatment time to produce these high performance films was less than 4 h. Rheology modifiers such as polyvinyl alcohol (PVA) and hydroxyethyl cellulose (HEC) were used to increase the thickness of deposited films independent of the solution cation concentration. Chelating agents such as polyethylene glycol (PEG) and sucrose increased the barium ion solubility. Nitrate crystallization during deposition was controlled through rapid drying with vacuum and coating with hot solutions.     

Growth of Cu0.5Tl0.5Ba2Ca3Cu4−yZnyO12−δ superconductor with optimum carriers

We have tried to vary the carriers concentration in Cu_0.5Tl_0.5Ba₂Ca₃Cu_4?yZn_yO_12?δ (y = 0, 1, 1.5, 2, 2.5) superconductor with the help of post-annealing experiments carried out in nitrogen, oxygen and air and to investigate its effects on the superconductivity parameters. The zero resistivity critical temperature [T_c(R = 0)], the magnitude of diamagnetism and critical current [I_c(H = 0)] are found to increase in Zn free samples after post-annealing in oxygen and air, while these superconducting properties have been suppressed after post-annealing in nitrogen at 550 °C for 6 h. The post-annealing of Zn-doped samples in air has marginally increased the superconducting properties, while these properties have been suppressed after post-annealing in nitrogen and oxygen. These studies have led us to the definite conclusion that the Zn-doped material has grown with optimum carriers concentration.     

The lightning striking distance—Revisited

First return stroke current waveforms measured by Berger [Methods and results of lightning records at Monte San Salvatore from 1963–1971 (in German), Bull. Schweiz. Elektrotech. ver. 63 (1972) 21403—21422] and Berger and Vogelsanger [Measurement and results of lightning records at Monte San Salvatore from 1955–1963 (in German), Bull. Schweiz. Elektrotech. ver. 56 (1965) 2–22] are used to estimate the charge stored in the lightning stepped leader channel. As opposed to previous charge estimates based on the entire current waveform, only the initial portion of measured current waveforms (100 μs in duration) was used in order to avoid the inclusion of any charges not involved in the effective neutralization of charges originally stored on the leader channel. The charge brought to ground by the return stroke within the first 100 μs, Q_f,100 μs (in C) is related to the first return stroke peak current, I_pf (in kA), as Q_f,100 μs=0.61 I_pf. From this equation the charge distribution of the stepped leader as a function of the corresponding peak return stroke current is estimated. This distribution (along with the assumed average electric field of 500 kV/m in the final gap) is used to estimate the lightning striking distance S (in meters) to a flat ground as a function of the prospective return stroke peak current I (in kA): S=1.9 I_pf^0.90. For the median first stroke peak current of 30 kA one obtains S=41 m, while the traditional equation, S=10 I_pf^0.65, gives S=91 m. In our view, the new equation for striking distance provides a more physically realistic basis for the electro-geometric approach widely used in estimating lightning incidence to power lines and other structures.     

Surface electromigration of In on vicinal Si(0 0 1)

Surface mass transport of In film on vicinal Si(0 0 1) has been systematically investigated by a scanning Auger electron microscopy (SAM), low energy electron diffraction (LEED) and atomic force microscopy (AFM). It was observed that the temperature dependence of the mass transport shows the critical phenomenon. Above a critical temperature T_c, surface electromigration of the In film toward the cathode side dominated the surface mass transport on the vicinal Si(0 0 1) surface. The LEED and AFM observations revealed that the In film surface on the vicinal Si(0 0 1) consists of 3×4 terraces and (3 1 0) facets. The area ratio of the facet to the terrace exhibited abrupt an increase at T_c. It is believed that the change of the mass transport is related to the abrupt change of the area ratio of the facet to the terrace. Both the critical temperature T_c and the spread due to the surface electromigration of the In film depended on the configuration of the DC current direction and the step edge.     

The effect of pinning centers in Zn-doped CuBa2Ca3Cu4O12−y high-temperature superconductors

CuBa₂Ca₃Cu₄O_12−y (Cu:1234) high-temperature superconductors (HTS) doped with up to 2% Zn were grown using the high-pressure synthesis technique. Magnetization loops of the samples were measured at various temperatures between 5 and 77.3 K and magnetic fields up to 14 T. Critical current densities J_c of the samples were estimated using the critical state model. The results show that Zn-induced pinning centers increase J_c of Cu:1234 several times, depending on field and temperature. From the experimentally determined field-temperature region in which a higher Zn concentration lead to a higher J_c, we suggest the existence of a cross-over from quite efficient, extended (in the c-axes direction) pinning centers to point-like (inefficient) pinning centers at a certain temperature, depending on field. This effect can be attributed to the fact that, unlike other HTS, in Cu:1234 there is a second critical temperature T_c2 of about 70–80 K (in zero field, and 50–60 K in 15 T), related to the over-doping of pyramidal basal plane (outer CuO₂ plane).     

Effects of nanoscale defects on critical current density of (Y1−xEux)Ba2Cu3O7−δ thin films

In pulsed laser deposition of YBa₂Cu₃O_7?δ films, defect introduction into the films tends to anisotropically improve the pinning along the H||c direction due to the columnar growth mode of the process. In Eu-substituted samples, however, even though an increase in critical current density (J_c) in the H||c direction was observed for low fields (H = 0.2 T), the improvement was more notable for the H||ab-plane at both low and higher fields. Herein we present detailed TEM microstructural studies to understand these new trends in J_c(H), which are markedly different than flux pinning increases achieved with other methods, for example, with nanoparticle additions. Threading dislocations, observed in the Eu-substituted samples along the c-axis, account for J_c enhancement with H||c at low field. The enhanced ab-planar pinning in the Eu-substituted samples is attributed to the extensive bending of the {0 0 1} lattice planes throughout the film, and the crystal lattice defects with excess Cu–O planes, that were effective in increasing the J_c for H||ab at both low and high fields.     

Homoepitaxial growth of MOD-YBCO thick films on evaporated and MOD templates

We have prepared metal organic deposition (MOD)-YBCO thick films by repeating the coating-pyrolysis-crystallization procedure onto ～100-nm-thick evaporated and MOD templates. Surface morphology of the template was found to strongly affect the homoepitaxial growth of MOD-YBCO layers on the template; namely, the epitaxial growth of MOD-YBCO on the evaporated template was much easier than that on the MOD template. A 220-nm-thick epitaxial MOD-YBCO film was successfully prepared on the 100-nm-thick evaporated-YBCO template to obtain a 320-nm-thick YBCO film, which exhibited J_c = 2.44 MA/cm² and I_c = 78 A/cm. The I_c value has significantly increased from 37 A/cm for the evaporated-template.     

Reel-to-reel fabrication of meter-long YBCO coated conductor

YBa₂Cu₃O_7?δ (YBCO) superconductors were coated on the CeO₂/YSZ/Y₂O₃ buffered Ni-5at%W tapes by a reel-to-reel pulsed laser deposition (PLD). The process of a multi-layer deposition of YBCO film was explored. X-ray diffraction texture measurements showed good both in-plane and out of plane crystalline orientations in YBCO films. The average values calculated at a full width at half maximum (FWHM) of the peaks from phi-scans (φ) and omega (ω) scans for one meter-long YBCO tape were 7.49° and 4.71°, respectively. The critical current (I_c) was over 200 A/cm-width at 77 K and under self-field for meter-long YBCO tape. The critical transition temperature of the YBCO tape was typically as 90.1 K with 0.5 K transition widths.     

Magnetic properties of RPdIn (R=Gd–Er) compounds

AC susceptibility and DC magnetization measurements were performed for the RPdIn (R=Gd–Er) compounds both in the paramagnetic and in the ordered state. In opposite to GdPdIn, which is a ferromagnet (T_c=102 K), the other samples show a complex ferrimagnetic behavior with the additional transition at T_t<T_c. In the high-temperature phase (for T_t<T<T_c), a ferromagnetic interaction dominates, while in the low-temperature phase (for T⩽T_t) antiferromagnetic interactions with the magnetocrystalline anisotropy, especially strong for TbPdIn, come into play. The ordering temperatures are T_c=70, 34, 25 and 12.3 K for Tb-, Dy-, Ho- and ErPdIn respectively, while transition temperatures are T_t=6, 14 and 6 K for Tb-, Dy- and HoPdIn respectively. TbPdIn reveals an additional transition at 27 K connected with the intermediate ferrimagnetic phase. The critical fields for the magnetization process of the low-temperature phase are high (52 and 150 kOe for TbPdIn and 32 kOe for DyPdIn at T=4.2 K) yet these values decrease remarkably with increasing temperature. Results of the study are compared with magnetic and neutron diffraction data hitherto available. We state that irreversibility of the zero-field cooled–field cooled magnetization is not connected with the spin-glass phase claimed elsewhere.     

Strongly enhanced flux pining of GdBCO coated conductors with BaSnO3 nanorods by pulsed laser deposition

We report the effects of BSO addition on the crystallinity, texture, and the field dependency of critical current density (J_c) of GdBCO coated conductors (CCs) prepared by pulsed laser deposition (PLD). Undoped and BSO-doped GdBCO films showed only c-axis oriented growth, and the incorporated BSO nanorods exhibited epitaxial relationship with the GdBCO matrix. In comparison with undoped film, BSO-doped GdBCO film exhibited greatly enhanced J_c and higher pinning force densities in the entire field region of 0–5 T (H//c) at 77 and 65 K. The BSO-doped GdBCO film showed the maximum pinning force densities (F_p) of 6.5 GN/m³ (77 K, H//c) and 32.5 GN/m³ (65 K, H//c), ～2.8 times higher than those of the undoped sample. Cross-sectional TEM analyses exhibited nano-structured BSO nanorods roughly aligned along the c-axis of the GdBCO film, which are believed effective flux pinning centers responsible for strongly improved critical current densities in magnetic fields.