互贯离子交换树脂的研究

本文研究了互贯树脂的交联度、两网的重量比与珠体膨胀度的关系;以及第三单体、合成工艺对树脂强度的影响,从而解决了互贯树脂耐疲劳强度问题。     

高交联大孔苯乙烯—二乙烯苯共聚物的磺化反应

研究了高交联大孔苯乙烯－二乙烯苯共聚物在有溶胀剂和无溶胀剂条件下,反应温度、反应时间及共聚物合成时所用致孔剂对其磺化反应的影响。结果显示,当磺化反应在不同溶胀剂介质中进行时,共聚物的交换容量随交联度变化可呈现不同的关系。与低交联大孔共聚物（交联度７％）比较,高交联大孔共聚物（交联度６０％）磺化反应速度更快,反应能在低得多的温度下进行,同时溶胀介质对磺化产物的交换容量的影响变得很小。６０％交联的共聚     

高交联大孔苯乙烯-二乙烯苯共聚物的磺化反应

研究了高交联大孔苯乙烯－二乙烯本共聚物在有溶胀剂和无溶胀剂条件下,反应温度、 反应时间及共聚物合成时所用致孔剂对其磺化反应的影响．结果显示,当磺化反应在不同溶胀 剂介质中进行时,共聚物的交换容量随交联度变化可是现不同的关系．与低交联大孔共聚物（交 联度７％）比较,高文联大孔共聚物（交联度６０％）磺化反应速度更快,反应能在低得多的温度下 进行,同时溶胀介质对磺化产物的交换容量的影响变得很小．６０％交联的共聚物于３５Ｃ反应３ｈ, 可获得接近于表面磺化的产物．     

对氟苯乙烯-二乙烯基苯强酸性阳离子交换树脂的合成及其热稳定性研究

以对氟苯乙烯，二乙烯苯为原料合成了强酸性阳离子交换树脂，考察了磺化反应的工艺条件及卤原子，树脂类型对树脂耐热稳定性能的影响。研究表明，对氟苯乙烯－二乙烯基苯共聚体需用发烟硫酸在110℃才可磺化，大孔磺化对氟苯乙烯－二乙烯基苯树脂在190℃水中20h的磺酸基降解率为24．7％，而普通磺酸树脂的磺酸基降解率为53．3％。     

互贯型螯合树脂的研究(Ⅰ)─交联聚苯乙烯－聚丙烯腈互贯树脂的合成

研究了交联聚苯乙烯-聚丙烯腈新型互贯树脂(PS-PAN)的合成,考察了交联度、重量比、孔结构和溶剂对互贯量的影响。结果表明,以凝胶型树脂为第一网时,交联度的影响比较显着,两网交联度相同时互贯量最大;以大孔型树脂做第一网时,孔结构的作用较突出。此外,溶剂对互贯量的影响非常大。     

一种用于色谱分离的凝胶型苯乙烯系阳离子树脂的制备方法

<正>公开号:CN103433010A公开日:2013.12.11申请人:凯瑞化工股份有限公司摘要本发明提供一种用于色谱分离的凝胶型苯乙烯系阳离子树脂的制备方法,选用凝胶型苯乙烯系阳离子交换树脂生产标准工艺配方中的升温方法及反应时间,生产出苯乙烯系聚合白球,然后在磺化时于硫酸中加入螯合剂及氟硼酸,经标准工艺磺化反应可得色谱分离树脂。相对于磺化时未加入螯合剂和氟硼酸的凝胶型苯乙烯系阳离子交换树脂,本发明制备色谱分离树脂吸附能力可提高50%;机械强度可提高20%。本发明制备的色谱分离树脂可提高果糖的含量,     

互贯型螯合树脂的研究．Ⅱ．IPN型含偕胺肟基螯合树脂的合成与性能研究

以交联聚苯乙烯－聚丙烯腈树脂为骨架，经功能基化反应制备出含偕胺肟基团的互贯型螯合树脂。对功能基化反应条件和螯合树脂对金的吸着性能，吸着选择性和吸着机理进行了研究。互贯型螯合树脂的吸着性能与互贯树脂的结构有关，而螯合树脂的选择吸着性则与互贯网络无关．     

高交换容量苯乙烯大孔强碱Ⅰ型阴离子交换树脂的合成

本工作合成的高交换容量苯乙烯大孔强碱1型阴离子交换树脂80A,理化性能接近于Amberlite IRA900C的水平。80A的重量交换量为4.0～4.4meq/g(干树脂),比表面积为40～50m~2/g,平均孔径为90～100。80A的中间体,是苯乙烯—二乙烯苯共聚物(白球)及其氯甲基化产物(氯球)。白球交联度为6～10,以汽油、液体石腊为混合致孔剂。氯甲基化反应,采用无水三氯化铝为催化剂,反应温度35～40℃,反应时间约8小时,氯球的氯含量高达20～23％。     

互贯磺酸树脂的离子交换平衡性质

本文研究凝胶型互贯磺酸树脂的热力学性质。测定了一系列第一网和第二网重量比及交联度不同的互贯磺酸树脂对多种离子交换反应的△G~0、△H~0和△S~0值。归纳了二重网重量比和交联度对△H~0、△S~0值变化影响规律。提出了用积分持水量来表达互贯磺酸树脂的平衡常数与持水量关系,并探讨了这类树脂在离子交换色谱等方面应用的可能性。     

室温交联型硅丙微胶乳的合成研究(1)硅烷单体对聚合稳定性和胶膜性能的影响

采用种子微乳液聚合工艺和单体半连续滴加法合成了室温交联型有机硅改性丙烯酸酯微胶乳，研究了硅烷单体种类和用量及其添加顺序等对聚合稳定和胶膜性能的影响。结果表明，使用含阻碍性铁新硅烷单体（C－1757）可明显抑制体系中的水解－缩合反应，提高聚合稳定性，而且随其用量增加，改性胶膜的交联密度增大，拉伸强度提高；延迟添加C－1757，可进一步提高聚合稳定性，但会降低胶膜的交联密度，拉伸强度先高后低，30／70处有一个最大值，所合成的硅丙微胶乳储存期可达长两年，与C－1757相比，硅烷单体A－174改性的胶膜具有更大的交联密度，而A－171改性的胶膜交联密度偏低，力学性能较差。     

丙烯酸酯类吸油树脂的合成与性能研究

以丙烯酸酯、甲基丙烯酸酯为主要单体,二丙烯酸丁二醇酯为交联剂,过氧化二苯甲酰为引发剂,采用悬浮聚合方法,合成聚丙烯酸酯类高吸油树脂.研究了分散剂、引发剂、交联剂用量及单体配比等因素对树脂吸油性能的影响.结果表明,分散剂用量为单体质量的0.12%,引发剂用量为1.0%,交联剂用量为1.5%时树脂的吸油能力最佳,吸甲苯倍率可达15倍,吸汽油倍率可达10倍,吸机油倍率可达近9倍.     

Development of new hydrophilic polymer supports based on dimethylacrylamide

A survey of the development of hydrophilic resins based on dimethylacrylamide (DMA) is presented. It describes the preparation of DMA-based resins by suspension copolymerization of DMA and acrylamide-based crosslinking and functional monomers. Swellability data for a number of DMA-based resins are tabulated, demonstrating that the resins swell to approximately the same extent in dichloromethane as they do in water, methanol, dimethylformamide or dimethylsulphoxide, but they swell only slightly or not at all in tetrahydrofuran. Typical chemical reactions employed for quantitative estimation or derivatization of resin-bound functional groups, including those involving intra-resin crosslinking, are discussed. The development of composite polymer supports, in which the DMA-based polymer is supported on kieselguhr particles or an amphiphilic ion exchange polymer is supported on DMA-based resin beads, is also covered briefly.     

单一化学交联与物理化学复合交联高吸油树脂的比较

提出在单一化学交联吸油树脂中引入物理交联的设想，并采用悬浮聚合法了单一化学交联和物理－化学复合交联的聚丙烯酸酯系高吸油树脂，对两种不同树脂的吸油速率，低亲油性单体树脂的吸油性能，最佳单体配比以及化学交联剂含量的影响进行了比较，结果表明物理交联的引入加快了树脂的吸油速率，提高低亲油性单体树脂的吸油能力，并且还使最佳单体配比中低亲油性单体含量增加，同时表明部分物理交联吸油树脂有一最佳化学交联剂含量区。     

凝胶型苯乙烯系离子交换树脂的强度及抗渗透性的影响因素研究 (I)

本文就单体组成中不同引发剂，链转移剂，环二烯，烯丙基类化合物和氧气等对凝胶型苯乙烯系阳离子交换树脂的强度和抗渗透性的影响进行了系统研究。结果显示，采用0．30％的过氧化2－乙基己酸叔丁酯（OT）和0．01％的过氧化苯甲酸特丁酯（CP）代替过氧化二苯甲酰（BPO作引发剂，或者加入0．02％的链转移剂十二烷基硫醇，均能够在一定程度上改善共聚物珠粒的结构均匀性，提高其合成的离子交换树脂的磨后圆球率和抗渗透性能。     

Cross‐linked waterborne alkyd hybrid resin coatings modified by fluorinated acrylate‐siloxane with high waterproof and anticorrosive performance

Waterborne alkyd resin coatings are ideal for use as corrosion protection coatings because of its high cost‐effective and environmental advantages. However, their uses are restricted to general applications due to their poor acid, water, and alkali resistance. In this work, waterborne alkyd hybrid resins modified with fluorinated acrylate‐siloxane were synthesized via a surfactant‐free miniemulsion polymerization process using maleic anhydride and silicon modified alkyd resin, dodecafluoroheptyl methacrylate, methyl methacrylate, and butyl acrylate as monomers. And then, crosslinking alkyd resin films were prepared at room temperature using trimethylolpropane‐tris‐(β‐N‐azir‐idinyl) propionate (XR‐100) as the crosslinking agent. The acquired films had lower water absorption and higher water contact angles and had better mechanical/thermal properties, as well as good waterproof property. Most importantly, the electrochemical corrosion studies revealed that the cross‐linked coating exhibited superior corrosion resistance performance with an inhibition efficiency of 99.95% and a corrosion rate of 6.95 × 10^?3 mm per year.     

Synthesis of high oil‐absorption resins of poly(methyl methacrylate‐butyl methacrylate) by suspended emulsion polymerization

The synthesis of high oil‐absorption resins by suspended emulsion polymerization process for the first time with butyl methacrylate (BMA) and short‐chain methyl methacrylate (MMA) as the monomers was studied. And the effects of different polymerization technological parameters, such as the comonomer, initiator, crosslinker, emulsifier, dispersant agent, and the agitation rate, on the oil absorbency of high oil‐absorption resins were discussed in detail. The optimum polymerization conditions were obtained. With the increasing contents of these factors, the oil absorbency increased first, and then decreased. The highest oil absorbency to toluene was 17.6 g/g. The particle morphology of the high oil‐absorption resins was observed by scanning electron microscopy (SEM). The resins were determined by FTIR spectrometry. Compared with the high oil‐absorption resins prepared by suspension polymerization process and emulsion polymerization process, the high oil‐absorption resins prepared by suspended emulsion polymerization process had the higher oil absorbency, faster oil‐adsorbing rate, better oil‐retention, and regeneration property. Copyright © 2010 John Wiley & Sons, Ltd.     

HIGH INDEX OPTICAL MATERIALS PREPARED BY COPOLYMERIZATION OF NOVEL BIFUNCTIONAL THIOMETHACRYLATES

Optical materials, such as ophthalmic lens, are thermosetting resins, which require crosslinking agents. An optical resin, having a high refractive index, is usually produced by radical copolymerization in which high index crosslinking monomers are significantly important. We provide here the resins prepared by radical polymerization of novel bifunctional thiomethacrylates as high index crosslinkers.     

Preparation and properties of aniline chain-extended thermoplastic epoxy resin using triphenylphosphine as catalyst

Thermoplastic resins have been widely used in fiber reinforced polymer composites because of its recyclability and short cycle times. However, the high viscosity after heating and melting restricts its infiltration on the surface of fiber. In this study, a series of thermoplastic epoxy resins were prepared via the chain extension reaction of epoxy groups with liquid aniline using triphenylphosphine (TPP) as catalyst. The relationship between polymer network structure and performance was comprehensively investigated. The solubility tests indicated that excessive aniline or TPP facilitated the crosslinking of resins. Besides, on the premise of thermoplasticity, appropriate TPP could increase the degree of chain extension, molecular weight, and glass transition temperature of resins. Furthermore, the in-situ polymerization process facilitated infiltration between epoxy resin and the fibers before chain extension reaction. The bending test showed that the flexural performance of the sample with 2 phr of TPP was improved by 38.8%. Therefore, this work provides a feasible method to prepare the thermoplastic epoxy resins and its fiber-reinforced composites with good mechanical properties.     

Absorption of amines on cation exchange resins

All the amines studied are absorbed in excess of the exchange capacity bysulfonated polystyrene resins from aqueous solutions; the absorption is greatest with benzylamine, whose molecular structure is the closest to that of the monomer of the resin. The absorption is greater, then less the crosslinking of the resin, and it is influenced by the electrostatic field of the resin cations. There is no excess absorption from solvents such as alcohols, acetic acid or dioxane. The absorption characteristics of amines are sufficiently different that separations by elution chromatography on cation exchange resins are possible. Two such separations have been demonstrated. For quantitative analytical use, however, it would be wise to use very fine mesh resins on account of the slowness of diffusion of large amine molecules within the resins.     

表面亲水性粒度单分散交联PMMA树脂的合成及表征

用种子溶胀聚合方法 ,合成出了粒度单分散的交联聚甲基丙烯酸甲酯微球 .将微球通过水解 ,使其转化为表面带羧基的树脂 .分别用多糖化合物Dextran和DEAE Dextran对水解树脂表面进行包覆涂层 ,然后用n 丁二醇双环氧丙醚分别进行交联 ,制备出两种表面带高交联多糖覆盖层的树脂 .以两种改性树脂为填料 ,以人血清蛋白为试样 ,用HPLC方法对树脂的亲水性能进行了表征 .研究表明 ,两种改性树脂均有很好的亲水性 ,蛋白质的回收率分别在 97%和 99%以上 ,并有良好的机械强度和化学稳定性