Poly(ether ether ketone)/poly(aryl ether sulphone) blends: thermal degradation behaviour

The thermodegradative behaviour of blends of poly(ether ether ketone) (PEEK) and poly(aryl ether sulphone) (PES) was studied by dynamic thermogravimetry in order to analyze their thermal stability. The Freeman-Carrol differential approach was used to determine the kinetic parameters i.e. the apparent activation energy (E_a) and order of reaction (n), of the degradation process. The results indicate that the presence of one component influences the thermal stability of the other. Both, temperature for 5% weight loss (T₅) and E_a for blends show a negative deviation from the linear behaviour, which signifies a lowering of thermal stability compared to homopolymers. The decrease in the thermal stability at low concentration of PES in PEEK has been explained on the basis of chemical interactions of the degradation products of PES, which has lower induction temperature for degradation, with PEEK and also on the reduction of viscosity of the medium. But the decrease in thermal stability at low concentration of PEEK in PES is unusual and at present, without the complete elucidation of degradation mechanism in these blends, is difficult to explain.     

Poly(ether ether ketone)/poly(aryl ether sulfone) blends: Melt rheological behavior

Dynamic rheological measurements were carried out on blends of poly(ether ether ketone) (PEEK)/poly(aryl ether sulfone) (PES) in the melt state in the oscillatory shear mode. The data were analyzed for the fundamental rheological behavior to yield insight into the microstructure of PEEK/PES blends. A variation of complex viscosity with composition exhibited positive–negative deviations from the log‐additivity rule and was typical for a continuous‐discrete type of morphology with weak interaction among droplets. The point of transition showed that phase inversion takes place at composition with a 0.6 weight fraction of PEEK, which agreed with the actual morphology of these blends observed by scanning electron microscopy. Activation energy for flow, for blend compositions followed additive behavior, which indicated that PEEK/PES blends may have had some compatibility in the melt. Variation of the elastic modulus (G′) with composition showed a trend similar to that observed for complex viscosity. A three‐zone model used for understanding the dynamic moduli behavior of polymers demonstrated that PEEK follows plateau‐zone behavior, whereas PES exhibits only terminal‐zone behavior in the frequency range studied. The blends of these two polymers showed an intermediate behavior, and the crossover frequency shifted to the low‐frequency region as the PEEK content in PES increased. This revealed the shift of terminal‐zone behavior to low frequency with an increased PEEK percentage in the blend. Variation of relaxation time with composition suggested that slow relaxation of PEEK retards the relaxation process of PES as the PEEK concentration in the blend is increased because of the partial miscibility of the blend, which affects the constraint release process of pure components in the blend. A temperature‐independent correlation observed in the log–log plots of G′ versus loss modulus (G″) for different blend systems fulfilled the necessary condition for their rheological simplicity. Further, the composition‐dependent correlations of PEEK/PES blends observed in a log–log plot of G′ versus G″ showed that the blends are either partially miscible or immiscible and form a discrete‐continuous phase morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1548–1563, 2004     

Polyetherether ketone/polyarylethersulfone blends: Thermal and compatibility aspects

The compatibility behavior of polyetherether ketone (PEEK) with poly(ether sulfone) (PES) has been reexamined using differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and extrudate swell measurements. The blends were prepared by both melt‐blending and solution‐blending techniques. The phase behavior of blends is strongly affected by the blending technique used. Blends prepared by solution‐blending are compatible in the entire composition range on the basis of the single composition‐dependent glass transitions and exhibit lower critical solution temperature (LCST) behavior. LCST was near 340 °C around which the crystalline melting point of PEEK exists. Near LCST melting‐induced movement of molecular chains disturbs the initial homogeneous state of the solution blends and leads to a phase‐separated state that is thermodynamically more stable in the absence of strong specific interactions between the homopolymers. Contrary to the solution‐blended samples, melt‐blended samples were in the phase‐separated state even at a lower processing temperature of 300 °C. Two glass transitions corresponding to a PEEK‐rich and a PES‐rich phase were found for all compositions. From the measured glass transition of phase‐separated blends, weight fractions of PES and PEEK dissolved in each phase were determined using the Fox equation. Compatibility is greater in the PEEK‐rich compositions than in the PES‐rich compositions. PEEK dissolves more in PES‐rich phases than does PES in the PEEK‐rich phase. Variation of the specific heat increment (ΔC_p) at the glass transition with composition also supports these inferences. Solution‐blended samples, quenched from 380 °C, also indicated similar behavior but were slightly more compatible. The aforementioned results are consistent with those inferred from SEM studies and extrudate swell measurements that show a greater compatibility in PEEK‐rich compositions than in PES‐rich compositions. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1407–1424, 2002     

结晶／结晶共混体系聚苯硫酸／聚醚醚酮中聚醚醚酮组分的结晶熔融行为──熔融温度的影响

igh performance crystal/crystal blends of poly (phenylene sulfide) and poly (ether ether ketone) (PPS/PEEK) have ho prepared by dry mixing and melhng at different temperatures. The crystallization and melting behavior of PEEK component in quenched blends have ho investigated by differential scanningcalorimetry (DSC). As melt temperature (T_melt) increases, the crystalline andmelting behavior of PPS and PEEK is different due to the difference of thermalproperty of PPS and PEEK. The temperature of melhng (T_m) and crystallization (T_c) and crystallinity (X_c) of PEEK component in blends increase as the content of PPS increases up to 50%. However. this action of PPS is suppresed with increasing of T_melt.     

Miscibility enhancement and formation of interpenetrating spherulites in ternary blends of crystalline polymers

Miscible blends of three crystalline polymers, namely poly(butylene succinate) (PBS), poly(ethylene succinate) (PES), and poly(oxyethylene) (POE), exhibited interpenetrating spherulites, where a spherulite of one component grows inside the spherulites of other components. PBS and PES were immiscible above the melting points, T_m, of these substances, while ternary blends with POE showed miscibility, which depended on the molecular weight of POE. PBS and PES exhibited the same spherulitic growth process as in a miscible binary blend when they were crystallized from a homogeneous ternary melt. Spherulites of PBS, which is the highest‐T_m component, filled the whole volume first when a miscible ternary blend was quenched below T_m of POE, the lowest‐T_m component. Then, the blends showed either two types of crystallization processes. One was successive nucleation and growth of PES and POE spherulites, that is, PES nucleated and developed spherulites inside the PBS spherulites and then POE spherulites grew inside the interlocked spherulites of PBS and PES. The other was simultaneous growth and the formation of interpenetrating spherulites of PES and POE inside the PBS spherulites. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 706–711, 2010     

Mechanical,aging, optical and rheological properties of toughening polylactide by melt blending with poly(ethylene glycol) based copolymers

Two novel biodegradable copolymers, including poly(ethylene glycol)-succinate copolymer (PES) and poly(ethylene glycol)-succinate-l-lactide copolymer (PESL), have been successfully synthesized via melt polycondensation using SnCl₂ as a catalyst. The copolymers were used to toughen PLA by melt blending. The DSC and SEM results indicated that the two copolymers were compatible well with PLA, and the compatibility of PESL was superior to that of PES. The results of tensile testing showed that the extensibility of PLA was largely improved by blending with PES or PESL. At same blending ratios, the elongation at break of PLA/PESL blends was far higher than that of PLA/PES ones. The elongation maintained stable through aging for 3 months. The moisture absorption of the blends enhanced due to the strong moisture absorption of PEG segments in PES or PESL molecules, which did not directly lead to enhance the hydrolytic degradation rate of the PLA. The PLA blends containing 20–30 wt% PES or PESL were high transparent materials with high light scattering. The toughening PLA materials could potentially be used as a soft biodegradable packaging material or a special optical material.     

Synthesis and properties of polyetheretherketone–polydimethylsiloxane block copolymers

Polyetheretherketone-polydimethylsiloxane (PEEK–PDMS) block copolymers were synthesized from the condensation of dimethylamino terminated PDMS and hydroxy terminated PEEK oligomers in 1-chloronapthalene. Yields for block copolymers synthesised from low molecular weight PDMS oligomers were good but yields were significantly reduced when higher molecular weight PDMS oligomers were used. This was related to the limited solubility of higher molecular weight PDMS in the reaction solvent. Differential scanning calorimetry (DSC) studies indicated that phase separation of the block copolymers occurred at very short segment length (M?_n < 4000). A depression in the crystallinity of both the PEEK and PDMS phases in the block copolymer was observed. Thermogravimetric analysis (TGA) studies indicated that the PEEK–PDMS block copolymers displayed insufficient thermo-oxidative stability to be melt-processed successfully in PEEK based blends.     

聚酰亚胺对高性能树脂共混体系界面的反应增强

研究了以5-降冰片烯-2,3-二羧酸单甲酯为端基的PMR型聚酰亚胺(POI)作为界面介质对部分相容的聚醚砜/聚苯硫醚(PES/PPS)、聚醚醚酮/聚醚砜(PEEK/PES)共混体系的界面性质、形态结构及结晶行为的影响.结果表明,POI可以有效地增强两相间的界面粘结,显著降低PPS/PES共混物中PPS分散区的尺寸,改善两组分间的相容性.在熔融共混过程中,POI从本体向界面扩散并同PPS,PES产生交联和/或接枝,POI同PPS的反应活性远高于PES,但POI与PES发生反应.POI是PPS结晶的有效成核剂.     

Glass transition and miscibility in blends of two semicrystalline polymers: Poly(aryl ether ketone) and poly(ether ether ketone)

Binary melt‐blended mixtures of two aryl ether ketone polymers (i.e., a new poly(aryl ether ketone) (code name PK99) and poly(ether ether ketone) (PEEK), have been studied. Polymer miscibility in glassy amorphous (or melt) domains has been demonstrated for the binary blend comprising of two aryl‐ether‐ketone‐type semicrystalline polymers. Composition‐dependent, single T_g was observed within full composition range in the PK99/PEEK blends, and the narrow T_g breadth also suggests that the scale of mixing was fine and uniform. To better resolve any possible overlapping T_g's, physical aging was imposed on a comparison set of blend samples for the purpose of improving detectability of overlapped multiple transitions if existing. The result still showed one single T_g. The relative sharp T_g and lack of cloud point transition suggest that the scale of molecular intermixing is good. Phase homogeneity was further confirmed using optical and scanning electron microscopy. The X‐ray diffractograms suggest that isomorphism does not exist in the PK99/PEEK blends and that the crystal forms of the respective polymers remain distinct and unchanged by the miscibility in the amorphous region. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1485–1494, 1999     

Glass transition,crystallization, and morphology relationships in miscible poly(aryl ether ketones) and poly(ether imide) blends

The relationships among glass transition, crystallization, melting, and crystal morphology of poly(aryl ether ketone) (PAEK)/poly(other imide) (PEI) blends was studied by thermal, optical and small-angle x-ray scattering (SAXS) methods. Two types of PAEK were chosen for this work: poly(aryl ether ether ketone), PEEK, and poly(aryl ether ketone ketone), PEKK, which have distinctly different crystallization rates. Both PAEKs show complete miscibility with PEI in the amorphous phase. As PAEK crystallizes, the noncrystallizable PEI component is rejected from the crystalline region, resulting in a broad amorphous population, which was indicated by the broadening and the increase of T_g over that of the purely amorphous mixture. The presence of the PEI component significantly decreases the bulk crystallization and crystal growth rate of PAEK, but the equilibrium melting temperature and crystal surface free energies are not affected. The morphology of the PEI segregation was investigated by SAXS measurements. The results indicated that the inter(lamellar-bundle) PEI trapping morphology was dominant in the PEEK/PEI blends under rapid crystallization conditions, whereas the interspherulitic morphology was dominant in the slow crystallizing PEKK/PEI blends. These morphologies were qualitatively explained by the expression δ=D/G, where G was the crystal growth rate and D was the mutual diffusion coefficient. © 1993 John Wiley & Sons, Inc.     

Melting point depression and phase behavior of poly(ether-sulfone) and poly(ethylene oxide) blends: Equation-of-state theory approach

Melting-point depression in miscible polymer blends is interpreted with Flory-Prigogine's equation-of-state theory (FP theory) and Sanchez-Lacombe's lattice fluid theory (LF theory). The equations for equilibrium melting point depression in polymer mixtures are proposed from both the FP and LF theories. For miscible poly(ether-sulfone) (PES)/poly(ethylene oxide) (PEO) blends, the proposed equations are tested. The interaction parameters, X₁₂ in FP theory and ζ₁₂ in LF theory, can be determined with these equations. The theoretically predicted equilibrium melting-point depression is subdivided into three terms, namely, the equation-of-state, the entropy and the contact interaction terms. When the estimated interaction parameters are converted to the heat of mixing by use of both theories, the composition dependence of the heat of mixing can be properly predicted. Using the interaction parameters obtained from the melting-point depression in PES/PEO blends, the spinodal curves are simulated from both the FP and LF theories.     

结晶／结晶共混体系聚苯硫酸／聚醚醚酮中聚醚醚酮组分的结晶熔融行为──熔融温度的影响

结晶／结晶共混体系聚苯硫酸／聚醚醚酮中聚醚醚酮组分的结晶熔融行为──熔融温度的影响麦堪成，许家瑞，梅震，曾汉民（中山大学材料科学研究所，广州，５１０２７５）关键词聚醚醚酮，聚苯硫醚，结晶／结晶共混物，结晶熔融行为近年来，高性能聚合物共混物如聚砜（ＰＳ...     

Recoverable compliance of a series of bimodal molecular weight blends of polystyrene

A series of bimodal molecular weight polystyrene blends was prepared. One component had a molecular weight greater than M_c and one less. The recoverable compliances were measured, and the retardation spectra determined via direct inversion. The retardation spectra of the blends are interpreted on the basis of the behavior of the spectra of the components, as a function of composition. It was observed that the low molecular weight component acted as a solvent. The effect of blending on the high molecular weight spectrum was to shift the position of the first peak to longer times and that of the second peak to shorter times. The peak separation was found to be proportional to the 3.4 power of the product of the molecular weight and the volume fraction of the high molecular weight component.     

Synthesis of polyphenylquinoxaline copolymers via aromatic nucleophilic substitution reactions of an A‐B quinoxaline monomer

A self‐polymerizable quinoxaline monomer (A‐B) has been synthesized and polymerized via aromatic nucleophilic substitution reactions. An isomeric mixture of self‐polymerizable quinoxaline monomers—2‐(4‐hydroxyphenyl)‐3‐phenyl‐6‐fluoroquinoxaline and 3‐(4‐hydroxyphenyl)‐2‐phenyl‐6‐fluoroquinoxaline—was polymerized in N‐methyl‐2‐pyrrolidinone (NMP) to afford high molecular weight polyphenylquinoxaline (PPQ) with intrinsic viscosities up to 1.91 dL/g and a glass‐transition temperature (T_g) of 251 °C. A series of comonomers was polymerized with A‐B to form PPQ/polysulfone (PS), PPQ/polyetherether ketone (PEEK), and PPQ/polyethersulfone (PES) copolymers. The copolymers readily obtained high intrinsic viscosities when fluorine was displaced in NMP under reflux. However, single‐electron transfer (SET) side reactions, which limit molecular weight, played a more dominant role when chlorine was displaced instead of fluorine. SET side reactions were minimized in the synthesis of PPQ/PS copolymers through mild polymerization conditions in NMP for longer polymerization times. Thus, the T_g's of PES (T_g = 220 °C), PEEK (T_g = 145 °C), and PS (T_g = 195 °C) were raised through the incorporation of quinoxaline units into the polymer. Copolymers with high intrinsic viscosities resulted in all cases, except in the case of PPQ/PEEK copolymers when 4,4′‐dichlorobenzophenone was the comonomer. © 2001 John Wiley & Sons, Inc. J Polym Sci A Part A: Polym Chem 39: 2037–2042, 2001     

Viscoelastic phase separation in polyethersulfone modified bismaleimide resin

The polymerization-induced phase separation process of polyethersulfone (PES) modified bismaleimide resin, 4,4′-bismaleimidodiphenylmethane (BDM), was investigated by time resolved light scattering (TRLS) and scanning electronic microscopes (SEM). At the blends with 10 wt% and 12.5 wt% PES, a phase inversion structure was found by SEM. TRLS results displayed clearly the spinodal decomposition (SD) mechanism and the exponential decay procedure of scattering vector q_m, which followed Maxwell-type relaxation equation. The characteristic relaxation time τ for the blends can be described by the Williams-Landel-Ferry equation. It demonstrated experimentally that the phase separation behaviors in these PES modified bismaleimide blends were affected by viscoelastic effect.     

Vitrification/devitrification phenomena during isothermal and nonisothermal crystallization of poly(aryl–ether–ether–ketone) (PEEK) and PEEK/poly(ether–imide) blends

We have established time–temperature transformation and continuous-heating transformation diagrams for poly(ether–ether–ketone) (PEEK) and PEEK/poly(ether–imide) (PEI) blends, in order to analyze the effects of relaxation control on crystallization. Similar diagrams are widely used in the field of thermosetting resins. Upon crystallization, the glass transition temperature (T_g) of PEEK and PEEK/PEI blends is found to increase significantly. In the case of PEEK, the shift of the α-relaxation is due to the progressive constraining of amorphous regions by nearby crystals. This phenomenon results in the isothermal vitrification of PEEK during its latest crystallization stages for crystallization temperatures near the initial T_g of PEEK. However, vitrification/devitrification effects are found to be of minor importance for anisothermal crystallization, above 0.1°C/min heating rate. In the case of PEEK/PEI blends, amorphous regions are progressively enriched in PEI upon PEEK crystallization. This promotes a shift of the α-relaxation of these regions to higher temperatures, with a consequent vitrification of the material when crystallized below the T_g of PEI. The data obtained for the blends in anisothermal regimes allow one to detect a region in the (temperature/heating rate) plane where crystallization proceeds in the continuously close proximity of the glass transition (dynamic vitrification). These experimental findings are in agreement with simple simulations based on a modified Avrami model coupled with the Fox equation. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 919–930, 1998     

Melting behavior of poly(ether ether ketone) in its blends with poly(ether imide)

We detail the melting behavior of poly(ether ether ketone) (PEEK) and investigate its melting behavior in miscible blends with poly(ether imide) (PEI). The determination of the equilibrium melting point (T_m⁰) of PEEK is discussed by considering its inhomogeneous morphology. T_m⁰ is obtained by a long extrapolation of a Hoffman–Weeks plot to 384°C. Hindrance of PEEK crystal reorganization induced by PEI during heating is observed over the blend composition investigated (20–75 wt % PEEK). This behavior is correlated with the incorporation of PEI in the interlamellar zones of PEEK crystals. The interaction parameter χ of PEEK/PEI blends is estimated by the equilibrium melting point depression. This gives the interaction density B = ?1.2 cal/cm³, and x = ?0.40 at 400°C. © 1993 John Wiley & Sons, Inc.     

Synthesis of a random copolymer and its compatibility for thermotropic liquid crystalline polymer/poly(ether ether ketone) blends

A random copolymer (RCP) containing poly(ether ether ketone) (PEEK) and thermotropic liquid crystalline polymer (TLCP) segments was synthesized. Its chemical structure and liquid crystalline properties were characterized by FT‐IR, differential scanning calorimetry (DSC) and polar light microscopy (PLM) respectively. A single glass transition temperature (T_g) at 134.0°C, a melting temperature (T_m) at 282.0°C and a temperature of ignition (T_i) at 331.3°C can be observed. Blends of PEEK and TLCP with and without RCP as compatibilizer were prepared by extrusion and the effect of RCP on the thermal properties, dynamic mechanical properties, morphology and static tensile mechanical properties of blends was investigated by means of DSC, dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), etc. Dynamic mechanical measurements indicated that there appeared to be only a single tan δ peak resulting from the glass transition of the PEEK‐rich phase and the T_g value shifted towards higher temperature due to the presence of compatibilizer, as suggested partial compatibility. Morphological investigations showed that the addition of RCP to binary blends reduced the dispersed phase size and improved the interfacial adhesion between the two phases. The ternary compatibilized blends showed enhanced tensile modulus compared to their binary blends without RCP. The strain at break decreased for the ternary blends due to embrittlement of the matrix by the incorporation of some RCP to the matrix phase. Copyright © 2007 John Wiley & Sons, Ltd.     

New approach on the development of plasticized polylactide (PLA): Grafting of poly(ethylene glycol) (PEG) via reactive extrusion

In this work, new ways of plasticizing polylactide (PLA) with low molecular poly(ethylene glycol) (PEG) were developed to improve the ductility of PLA while maintaining the plasticizer content at maximum 20 wt.% PLA. To this end, a reactive blending of anhydride-grafted PLA (MAG-PLA) copolymer with PEG, with chains terminated with hydroxyl groups, was performed. During the melt-processing, a fraction of PEG was grafted into the anhydride-functionalized PLA chains. The role of the grafted fraction was to improve the compatibility between PLA and PEG. Reactive extrusion and melt-blending of neat and modified PLA with PEG did not induce any dramatic drop of PLA molecular weight. The in situ reactive grafting of PEG into the modified PLA in PLA/PEG blends showed a clear effect on the thermal properties of PLA. It was demonstrated by DSC that the mobility gained by PLA chains in the plasticized blends yielded crystallization. The grafting of a fraction of PEG into PLA did not affect this process. However, DSC results obtained after the second heating showed an interesting effect on the T_g when 20 wt.% PEG were melt blended with neat PLA or 10 wt.% MAG-PLA. In the latter case, the T_g displayed by the reactive blend was shifted to even lower temperatures at around 14 °C, while the T_g of neat PLA and PLA blended with 20 wt.% PEG was around 60 and 23 °C, respectively. Regarding viscoelastic and viscoplastic properties, the presence of MAG-PLA does not significantly influence the behavior of plasticized PLA. Indeed, with or without MAG-PLA, elastic modulus and yield stress decrease, while ultimate strain increases with the addition of PEG into PLA.     

聚酰胺6／聚醚砜共混体系的结晶与熔融行为

聚醚砜（ＰＥＳ）是一种非晶特种工程塑料，具有强度好，使用温度高等特点，但熔体粘度高，加工上有一定困难．聚酰胺６（ＰＡ６）是部分结晶的工程塑料，有很好的强度和耐磨性能．加入适量的ＰＡ６，可显著地降低ＰＥＳ的熔体粘度，且可基本保持ＰＥＳ的原有性能［１］．...