Photoinitiated polymerization of methacrylates comprising phenyl moieties

Investigation of photopolymerization kinetics of 4-(4-methacryloyloxyphenyl)-butan-2-one (1) in comparison with 2-phenoxyethyl methacrylate (2) and phenyl methacrylate (3) using a UV-LED emitting at 395 nm shows significantly faster polymerization of 1 compared to both 2 and 3 at 40°C. Vitrification affects photopolymerization kinetics of all methacrylates under investigation. Interestingly, quantitative final conversion is observed during photoinitiated polymerization of 1 and 2 whereas 3 shows limited conversion at about 80%. Furthermore, higher degree of polymerization is obtained by photoinitiated polymerization of 1 compared to 2 and 3. This shows that the 3-oxobutyl substituent at the phenyl ring of 1 significantly affects both polymerization kinetics and final conversion of the photoinitiated polymerization. Moreover, an additional higher molecular weight fraction is observed in case of polymerization of 1 at 85°C that is above the glass transition temperature of the polymer formed during photoinitiated polymerization. As a thermal polymerization at 85°C in the absence of light results in a high molecular weight polymer as well, an additional thermal process may be discussed as reason for the higher molecular weight polymer fraction in case of the photopolymer made at 85°C.     

Kinetic study for adsorption of α-naphtholphthalein onto silica gel surface-imprinted polymer and non-imprinted polymer

In this study, the molecular imprinting polymer (MIP) was prepared using α-naphtholphthalein as a template, 2-(diethylamino)ethyl acrylate as a functional monomer and ethylene glycol dimethacrylate as a crosslinking agent by aid of free radical polymerization onto surfaces of vinyltrimethoxysilane modified silica gel. The MIP was extracted with acetonitrile for overnight to remove the template molecule from the MIP. Non-imprinted polymer (NIMP) was synthesized using the same materials except α-naphtholphthalein as template molecule. α-Naphtholphthalein adsorption on surfaces of the both polymer was studied at three different temperatures (19°C, 25°C and 35°C). It was observed that the adsorption capacity increased with increasing temperature and with time. The time required to reach the equilibrium for two polymers and all temperature was accepted to be nearly 6 h. The saturated adsorption amounts at the equilibrium were found as 120 mg/g, 123 mg/g and 127 mg/g at 19°C, 25°C and 35°C, respectively, for MIP, and 78 mg/g, 98 mg/g and 120 mg/g at 19°C, 25°C and 35°C, respectively, for NIMP. The mechanism of adsorption of α-naphtholphthalein onto MIP and NIMP is nearly appropriate to pseudo-first-order kinetic model with an activation energy of 11.63 kJ/mol for MIP, and 23.69 kJ/mol for NIMP. Thermodynamic parameters of activated complex in the adsorption process showed that the adsorption was carried out with an endothermic activation enthalpy, large negative entropy changes and the positive values of ΔG* that the adsorption processes is not favorable.     

γ-Ray-induced polymerization of α-haloacrylic acids

The γ-ray induced polymerizations of α-chloroacrylic acid, mp 66°C, and α-bromo-acrylic acid, mp 72°C, were investigated in the temperature range from 35°C to 85°C. An analysis of polymerization kinetics was made, and results were similar to those reported in the literature for other vinyl monomers. On heating of the polymer obtained, elimination of hydrogen halide takes place, and intramolecular lactone formation is observed. The rate of lactone formation of poly(α-chloroacrylic acid) obtained in the solid-state polymerization was found to be higher than that in the liquid state, because a highly isotactic configuration of polymers, tends to be formed in the solid-state polymerization, and elimination of hydrogen chloride is facilitated with an isotactic 5₂ helix structure.     

Effect of Stabilizer Concentration,Pressure and Temperature on Polymerization Rate and Molecular Weight Development in RAFT Polymerization of MMA in scCO2

Summary: An experimental study on the effect of stabilizer concentration, pressure (100 to 500 bar), and temperature (65 to 85 °C) on polymerization rate and molecular weight development in the reversible addition-fragmentation chain transfer (RAFT) polymerization of methyl methacrylate (MMA) in supercritical carbon dioxide (scCO₂) is presented. AIBN was used as initiator, S-Thiobenzoyl thioglycolic acid as RAFT agent, and Krytox® 257 FSL as stabilizer. It was observed that the polymerization proceeded in a controlled manner. High conversions can be reached in reasonable times. Fairly low polydispersities (around 1.2) are possible if either pressure or temperature are increased, but better results are obtained if the polymerization proceeds at the upper temperature value of 85 °C.     

A study of radical polymerization of N-vinylpyrrolidone in the presence of poly(methacrylic acid) templates by DSC

The template polymerization of N-vinylpyrrolidone (NVP) along syndiotactic poly(methacrylic acid) (s1-PMAA) templates has been studied by differential scanning calorimetry (DSC) using the scanning as well as the isothermal technique. The resulting Arrhenius plot covers a temperature range between 65 and 120°C and two parts can be distinguished. Below 80°C the overall activation energy, E_a, and entropy ΔS^≠, are 76 kJ · mol^?1 and ?79 J · mol^?1 · K^?1 respectively, in excellent agreement with previous dilatometric results. These values differ slightly from those of the blank polymerization leading to rate enhancement by a factor of only two. The small difference in activation parameters is explained by the occurrence of desolvation of st-PMAA chains during propagation of the polyvinylpyrrolidone (PVP) radicals along the template. Above 80°C, the decreasing tendency to form complexes between PVP and st-PMAA results in a decreasing template effect and a gradual change of apparent E_a and ΔS^≠ values towards those of the blank polymerization. Similar results were obtained with atactic and isotactic PMAA templates, but smaller rate enhancements were observed due to weaker complex formation.     

An Unexpected Molecular Imprinting Effect for a Polyaromatic Hydrocarbon,Anthracene, Using Uniform Size Ethylene Dimethacrylate Particles

A non-covalent type of molecular imprinting effect toward a polyaromatic hydrocarbon (PAH), viz. anthracene, was studied utilizing uniformly sized ethylene dimethacrylate (EDMA) polymer particles without functional host monomers. Although polymerization at 0°C initiated by a redox initiation system was expected to afford larger molecular imprinting effect due to stronger and more effective intermolecular interaction between the template and surface functional groups of the polymer, almost no imprinting effect was observed, while a much higher polymerization temperature of 70°C unexpectedly afforded a larger molecular imprinting effect for the template anthracene. In order to determine the unexpected imprinting effects observed, uniformly sized, macroporous un-imprinting EDMA polymer particles (base particles) were prepared by various polymerization techniques at different polymerization temperature as well as with different initiation systems. The careful studies proved that each kind of base polymer particle showed different molecular recognition ability, especially toward anthracene, which is depends upon the physical properties of each kind of base polymer particle. On the basis of these facts, we would propose that the potential molecular recognition ability of the un-imprinted base polymer particles is another important factor for realization of effective molecular imprinting alongside the factors reported previously.     

Radical polymerization of methyl methacrylate in the presence of stereoregular poly(methyl methacrylate). V. Kinetics of initial template polymerization

The influence of stereoregular poly(methyl methacrylate) (PMMA) as a polymer matrix on the initial rate of radical polymerization of methyl methacrylate (MMA) has been measured between ?11 and +60°C using a dilatometric technique. Under proper conditions an increase in the relative initial rate of template polymerization with respect to a blank polymerization was observed. Viscometric studies showed that the observed effect could be related to the extent of complex formation between the polymer matrix and the growing chain radical. The initial rate was dependent on tacticity and molecular weight of the matrix polymer, solvent type and polymerization temperature. The accelerating effect was most pronounced (a fivefold increase in rate) at the lowest polymerization temperature with the highest molecular weight isotactic PMMA as a matrix in a solvent like dimethylformamide (DMF), which is known to be a good medium for complex formation between isotactic and syndiotactic PMMA. The acceleration of the polymerization below 25°C appeared to be accompanied by a large decrease in the overall energy and entropy of activation. It is suggested that the observed template effects are mainly due to the stereoselection in the propagation step (lower activation entropy Δ S_p^?) and the hindrance of segmental diffusion in the termination step (higher activation energy Δ E_t^?) of complexed growing chain radicals.     

Controlled radical polymerization of styrene mediated by the C‐phenyl‐N‐tert‐butylnitrone/AIBN pair: Kinetics and electron spin resonance analysis

Kinetics of the free radical polymerization of styrene at 110 °C has been investigated in the presence of C‐phenyl‐N‐tert‐butylnitrone (PBN) and 2,2′‐azobis(isobutyronitrile) (AIBN) after prereaction in toluene at 85 °C. The effect of the prereaction time and the PBN/AIBN molar ratio on the in situ formation of nitroxides and alkoxyamines (at 85 °C), and ultimately on the control of the styrene polymerization at 110 °C, has been investigated. As a rule, the styrene radical polymerization is controlled, and the mechanism is one of the classical nitroxide‐mediated polymerization. Only one type of nitroxide (low‐molecular‐mass nitroxide) is formed whatever the prereaction conditions at 85 °C, and the equilibrium constant (K) between active and dormant species is 8.7 × 10^?10 mol L^?1 at 110 °C. At this temperature, the dissociation rate constant (k_d) is 3.7 × 10^?3 s^?1, the recombination rate constant (k_c) is 4.3 × 10⁶ L mol^?1 s^?1, whereas the activation energy (E_a,diss.), for the dissociation of the alkoxyamine at the chain‐end is ～125 kJ mol^?1. Importantly, the propagation rate at 110 °C, which does not change significantly with the prereaction time and the PBN/AIBN molar ratio at 85 °C, is higher than that for the thermal polymerization at 110 °C. This propagation rate directly depends on the equilibrium constant K and on the alkoxyamine and nitroxide concentrations, as well. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1219–1235, 2007     

A novel rate‐accelerating additive for atom transfer radical polymerization of styrene

The polymerization of styrene was mediated by copper (I) bromide/pentramethldiethyltriamine (PMDETA) using ethyl 2‐bromopropionate (EBP) as initiator and a catalytic amount of malononitrile (MN) as a novel rate‐accelerating additive. The optimal molar ratios of MN/EBP under which the polymerization of styrene can proceed fastest was 4:1. The rate‐enhancement‐efficiency had a dependence on temperature and the apparent rate constant of polymerization improved by a factor of 2.67 at 85 °C. Polymerization resulted in a conversion as high as 87% in 4.3 h in the presence of MN, while a conversion of 79.7% was gained even in 10 h without MN at 85 °C. The polymerizations of styrene in the presence of MN proceeded in a living fashion indicated by the first‐order kinetic plots, with the increase of M_n with respect to conversion and the relatively narrow polydispersity. The possible rate enhancing mechanism is that the addition of MN weakens the coordination between the copper center and ligand and facilitates the atom transfer process. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4082–4090, 2007     

Relevance of a prereaction for the in situ NMP of styrene using the C‐Phenyl‐N‐tert‐butylnitrone/2,2′‐azobis(isobutyronitrile) pair

In this article, we compare two routes for carrying out in situ nitroxide‐mediated polymerization of styrene using the C‐phenyl‐N‐tert‐butylnitrone (PBN)/2,2′‐azobis(isobutyronitrile) (AIBN) pair to identify the best one for an optimal control. One route consists in adding PBN to the radical polymerization of styrene, while the other approach deals with a prereaction between the nitrone and the free radical initiator prior to the addition of the monomer and the polymerization. The combination of ESR and kinetics studies allowed demonstrating that when the polymerization of styrene is initiated by AIBN in the presence of enough PBN at 110 °C, fast decomposition of AIBN is responsible for the accumulation of dead polymer chains at the early stages of the polymerization, in combination with controlled polystyrene chains. On the other hand, PBN acts as a terminating agent at 70 °C with the formation of a polystyrene end‐capped by an alkoxyamine, which is not labile at this temperature but that can be reactivated and chain‐extended by increasing the temperature. Finally, the radical polymerization of styrene is better controlled when the nitrone/initiator pair is prereacted at 85 °C for 4 h in toluene before styrene is added and polymerized at 110 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1085–1097, 2009     

Thermal Properties of Oligo(2-ethyl-2-oxazoline) Containing Comb and Graft Copolymers and their Aqueous Solutions

Summary: The cationic ring opening polymerization of 2-ethyl-2-oxazoline (EtOx) was applied for the synthesis of methacrylate end-functionalized well-defined macromonomers that could be polymerized in a controlled manner using reversible addition-fragmentation chain transfer polymerization. The obtained comb polymers revealed lower critical solution temperature behavior in aqueous solution. The cloud points of these solutions could be tuned in a range from 35 °C to 85 °C by the incorporation of hydrophobic methyl methacrylate comonomer in varying amounts into the graft copolymers whereas copolymerization with methacrylic acid rendered temperature and pH sensitive copolymers. Thermo-gravimetric analysis showed a two-step decomposition of the graft copolymers and differential scanning calorimetry revealed glass transition temperatures that are significantly lowered in comparison to linear PEtOx.     

Combination of Silica Sol and Potassium Silicate via Isothermal Heat Conduction Microcalorimetry

Isothermal heat conduction microcalorimetry was utilized as a novel characterization method to investigate the polymerization processes of silica with both thermodynamic and kinetic parameters when the combination of silica sol and potassium silicate was stirred at temperatures of 25.0, 35.0, and 45.0°C. The silica polymerization was characterized by the greater enthalpy change at each higher temperature and by the reaction orders of the silica sol and potassium silicate, which varied rapidly, instantaneously, and constantly from low to high all the time, up and down in an alternate manner. When the reaction order of the silica sol and potassium silicate was 3.0, the maximum rate constant occurred at 25.0°C (k=1.22×10^?4mol^?2·dm⁶·s^?1). The two temperature regions (25.0–35.0°C region with a faster rate and 35.0–45.0°C region with a lower rate) reflected a two‐stage oligomerization of silica monomers with different oligomers formed in a two‐step anionic mechanism. The measurements of particle size and pH value showed that the colloidal particles in the mixed silica sol and potassium silicate first dissolved, then "active" silica in the potassium silicate redeposited to make a distinct particle size distribution (Z‐average size, 33.0–14.9 nm at 25.0°C) influenced both by pH value (9.82–11.97 at 25.0°C) and the mass fraction (53, 65, 75, and 85 mass/%) of the silica sol in the mixture. The processes of combination of the silica sol and potassium silicate did not result from acid‐base neutralization reactions but from a complex polymerization of the "active" silica components which relate to silica monomers oligomerization with heat evolved (the total enthalpy changes, 1.6234–3.3882 J).     

Radical polymerization of methyl methacrylate in the presence of isotactic poly(methyl methacrylate). VIII. Influence of template concentration

The influence of template concentration on the radical polymerization of methyl methacrylate along isotactic poly(methyl methacrylate) template was studied. The polymerizations were carried out on three template polymers with different molar masses in dimethylformamide at ?5°C. The initial polymerization rate increased linearly with template concentration until the distribution of template chain segments became homogeneous. At that critical concentration a strong increase in the polymerization rate was observed, whereas still higher template concentrations had only a slight effect on the polymerization rate. The polymerizations were stopped when the weight ratio of formed polymer and template was equal to one. The viscometrically determined molar mass of the formed polymers showed a remarkable behavior in the low template concentration region. It was obviously related to the molar mass of the template polymer and was lower than the molar mass found for blank polymerization. This decrease in molar mass was most pronounced in the case of the lowest template molar mass. It is suggested that nondegradative chain transfer occurring near a template chain end is responsible for this decrease. An increase in the molar mass occurred at the critical concentration, similarly to the change of polymerization rate. However, at still higher template concentrations, where template coils started to overlap each other, the molar mass of the formed polymers increased further. The growing chains could leap from one template chain to another and attain a greater chain length than the blank polymerizate.     

The synthesis and thermal polymerization of 4,4′-diethynylphenyl ether

Diethynylphenyl ether (DEPE) was synthesized and its thermal polymerization studied by NMR, IR, and DSC techniques. DEPE is a crystalline solid that melts at 72–73°C and undergoes polymerization beginning at about 150°C. The heat of polymerization measured by DSC was 53 ± 2 kcal/mole. Thermomechanical analysis (TMA) of the fully cured resin showed softening behavior at temperatures in excess of 400°C. Weight loss up to 720°C was only 21%. A mechanism of polymerization based on the analysis of IR and NMR data for party polymerized material below 300°C is proposed.     

Vinyl Polymerization. 401. Polymerization of Vinyl Monomer Initiated with Poly-2-hydroxyethylmethacrylate

The polymerization of vinyl monomer initiated with poly-2-hydroxyethylmethacrylate (PHEMA) in water was carried out at 85°C. Cu(II) ion was not necessary for this polymerization. Methacrylate monomers were polymerized, while styrene and acrylonitrile were not. The polymerization was found to proceed through a radical mechanism in the interior of PHEMA which was swelled in water. The grafting efficiency of MMA polymer obtained was about 90%. The overall activation energy was estimated to be 32.9 kJ/mol.     

Template atom transfer radical polymerization of a diaminopyrimidine‐derivatized monomer in the presence of a uracil‐containing polymer

Uracil‐derivatized monomer 6‐undecyl‐1‐(4‐vinylbenzyl)uracil and diaminopyrimidine‐derivatized monomer 2,6‐dioctanoylamido‐4‐methacryloyloxypyrimidine (DMP) were synthesized and polymerized by atom transfer radical polymerization (ATRP). A well‐defined, highly soluble, uracil‐containing polymer, poly[6‐undecyl‐1‐(4‐vinylbenzyl)uracil] (PUVU), was prepared in dioxane at 90 °C with CuBr/1,1,4,7,10,10‐hexamethyltriethylenetetramine as the catalyst and methyl α‐bromophenylacetate as the initiator. PUVU was further used as a template for the ATRP of DMP. The enhanced apparent rate constant of the DMP polymerization in the presence of PUVU indicated that the ATRP of DMP occurred along the PUVU template. The template polymerization produced a stable and insoluble macromolecular complex, PUVU/poly(2,6‐dioctanoylamido‐4‐methacryloyloxypyrimidine). An X‐ray diffraction study confirmed that the complex had strandlike domains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6607–6615, 2006     

Bark Suberin as a Renewable Source of Long-Chain ω-Hydroxyalkanoic Acids

Summary : Polycondensations of cis-9,10-epoxy-18-hydroxyoctadecanoic acid, isolated from birch outer bark, were performed at 75 °C in toluene as solvent and at 85 °C in bulk using immobilized Candida antarctica lipase B as catalyst. The polycondensation performed in toluene in presence of molecular sieves gave a polyester with DP 50 after 24 h. The same DP was obtained at much shorter reaction time (3 h) by bulk polymerization in an open vial without any drying agent present.     

Sol–gel polycondensation of tetraethoxysilane in ethanol in presence of vinyl modified guar gum: synthesis of novel nanocompositional adsorbent materials

Novel nanocomposite adsorbent materials were synthesized by condensation polymerization of TEOS in the presence of saponified guar-graft-poly(acrylonitrile) (SG) as template. The effect of changing the molecular size of SG on the final properties of the composite materials was investigated in this paper. The composites were thermally treated at temperatures ranging from 80 to 1100 °C, to obtain materials of different performance. The chemical, structural and textural characteristics of the composites were determined by FTIR, XRD, TGA-DSC and SEM studies. Their adsorption properties were monitored in terms of Zn (II) binding capacity which could be tailored by changing the template size and sintering temperature. The adsorption capacity of the composite at room temperature was enhanced five times when thermally treated at 900 °C with a maximum adsorption of 3.58 meq/g of the zinc (II). The adsorption could be further optimized to higher values and the materials could be successfully recycled for three consecutive cycles without any significant loss in the adsorption capacity.     

Solvent-free polycondensation of 1,3-bis(hydroxyphenylmethyl)benzene. II. The dramatic difference in the polymerization behavior between meso and racemic isomers

The meso and racemic forms of 1,3-bis(hydroxyphenylmethyl)benzene underwent solvent-free polycondensation with the aid of an acid catalyst giving polyether. Very interestingly, the diastereoisomerism caused a considerable difference in the polymerization behavior. The meso isomer (mp = 96–98 °C) was polymerized even at 65 °C, whereas the racemic one (mp = 158–160 °C) required heating at 100 °C to undergo polymerization. However, the latter produced a much higher molecular weight than the former (30,000 vs 4000). The contamination of the meso isomer with the racemic one very sensitively reduced the polymerization temperature: the 98.5% meso monomer underwent polymerization at 50 °C. In contrast to solvent-free polymerization, two diastereomeric monomers showed almost identical behavior in solution polymerization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3564–3571, 2003     

Vinyl Polymerization. 374. Radical Polymerization of Vinyl Monomer Initiated with Sodium Polystyrenesulfonate

The polymerization of vinyl monomer initiated by an aqueous solution of sodium polystyrenesulfonate (PSS-Na) was carried out at 85°C. Methyl methacrylate (MMA) and styrene were polymerized, while acrylonitrile was not. The rate of polymerization of MMA decreased with the increase of the degree of polymerization of PSS-Na. However, the polymerization was not initiated by sodium ethyl benzenesulfonate which was a unit molecule of PSS-Na. The polymerization proved to be a radical reaction. The polymerization was considered to commence with the formation of hydrophobic areas with PSS-Na in the aqueous phase. MMA is incorporated into these areas, and there the polymerization is initiated and proceeds. The hydrophobic areas were assumed to be similar to the micelles formed by anionic detergents such as sodium alkylbenzene sulfonate. An initiation mechanism is proposed.