Syndioselective propylene polymerization catalyzed by rac-2,2-dimethylpropylidene (1-η5-cyclopentadienyl) (1-η5-fluorenyl) dichlorozirconium

Syndioselective propylene polymerization has been promoted by rac-2,2-dimethylpropylidene (1-η⁵-cyclopentadienyl) (1-η⁵-fluorenyl) dichlorozirconium ( 1 ). The active catalytic species were generated using either triphenylcarbenium tetrakis (pentafluorophenyl) borate ( 2 ) (Zr⁺ method) or methylaluminoxane (MAO method). The former exhibited much higher activity than the latter, especially at low polymerization temperatures (T_p). Syndiotactic poly (propylene) (s-PP) obtained at T_p = ?20°C has T_m approaching 160°C, [rrrr] pentad fraction of 0.92 to 0.95, and 45% crystallinity (X_c). It crystallized in two antichiral unit cells B and C. The C structure is favored by low temperature of polymerization, slow crystallization from melt, and annealing. The s-PP has M?_w/M?_n ranging from 3.6 to 4.4, which can be separated into stereoregular fractions soluble in heptane and hexane and stereoirregular fractions soluble in pentane, ether, and acetone. Therefore, this system cannot be considered to be a single-site catalyst. A parallel study was made on the isopropylidene (1-η⁵-cyclopentadienyl) (1-η⁵-fluorenyl) dichlorozirconium ( 3 )/MAO catalyst. Molecular mechanics calculations were performed for all combinations of the configuration of asymmetric centers. The steric energy favors syndiotactic enchainment for both catalysts 1 and 3 , with 1 forming the more syndioselective catalyst. © 1994 John Wiley & Sons, Inc.     

Heptane-soluble homogeneous zirconocene catalyst: Synthesis of a single diastereomer,polymerization catalysis,and effect of silica supports

Bis(1-indenyl)-di[1′S, 2′R, 5′S)-methoxy]silane ( 1 ) was converted into a mixture of corresponding ansa-diastereomeric zirconocenes. Further purification afforded a single dia-stereomer, di[(1′S, 2′R, 5′S)-methoxy] silylene-bis[η⁵-1(R, R)-(+)-indenyl] dichlorozirconium ( 2 ), which is optically active and hydrocarbon soluble. Extremely rapid ethylene, propylene, and ethylene-hexene polymerizations were observed both in toluene and n-heptane solutions; for instance, at 50°C, activity for ethylene polymerization reaches ～ 1.5×10¹⁰ (g of PE/((mol of Zr) · [C₂H₄] · h). The “bare” zirconocenium ion generated from 2/TIBA/Ph₃CB(C₆F₅)₄ exhibits unusual polymerization behaviors; the polymerization activity increases monotonically with temperature of polymerization (T_p) up to a conventional polymerization condition (50–70°C), and the ¹³C NMR study shows that the isotactic poly-propylene obtained has fairly high [mmmm] methyl pentad distributions at high T_p (?25°C with [mmmm] ～ 0.93–0.75) and a perfect stereoregularity at low T_p (?0°C with [mmmm] > 0.99). The catalyst precursors 2 and Et(Ind)₂ZrCl₂ ( 3 ) supported on silica by different approaches produced poly(olefins) of different molecular weights and stereoregularities, and a methylaluminokane and Ph₃CB(C₆F₅)₄ free silica-supported zirconocene system was found to be activated by triisobutylaluminum. © 1995 John Wiley & Sons, Inc.     

Polymerizations of olefins and diolefins catalyzed by monocyclopentadienyltitanium complexes containing a (dimethylamino)ethyl substituent and comparison with ansa-zirconocene systems

{[2-(dimethylamino)ethyl]cyclopentadienyl}titanium trichloride (Cp^NTiCl₃, 1 ) was activated with methylaluminoxane (MAO) to catalyze polymerizations of ethylene (E), propylene (P), ethylidene norbornene (ENB), vinylcyclohexene (VCH), and 1,4-hexadiene (HD). The dependence of homopolymerization activity ( A ) of 1 /MAO on olefin concentration ([M]ⁿ) is n = 2.0 ± 0.5 for E and n = 1.8 ± 0.2 for P. The value of n is 2.4 ± 0.2 for CpTiCl₃/MAO catalysis of ethylene polymerization; this system does not polymerize propylene. 1 /MAO catalyzes HD polymerization at one-tenth of A _H for 1-hexene, probably because of chelation effects in the HD case. The copolymerization of E and P has reactivity ratios of r_E = 6.4 and r_P = 0.29 at 20°C, and r_Er_P = 1.9, which suggests 1 /MAO may be a multisite catalyst. The copolymerization activity of CpTiCl₃/MAO is 50 times smaller than that of Cp^NTiCl₃/MAO. Terpolymerization of E/P/ENB has A of 10⁵ g of polymer/(mol of Ti h), incorporates up to 14 mol % (∼ 40 wt %) of ENB, and high MW's of 1 to 3 × 10⁵. All of these parameters are surprisingly insensitive to the ENB concentration. The E/P/VCH terpolymerization has comparable A value of (1.3 ± 0.3) × 10⁵ g/(mol of Ti h). The incorporation of VCH in terpolymer increases with increasing [VCH]. Terpolymerization with HD occurs at about one-third of the A of either ENB or VCH; the product HD–EPDM is low in molecular weight and contains less than 4% of HD. These terpolymerization results are compared with those obtained previously for three zirconocene precursors: rac-ethylenebis(1-η⁵-indenyl)dichlorozirconium ( 6 ), rac-(dimethylsilylene)bis(1-η⁵-indenyl)dichlorozirconium ( 7 ), and ethylenebis(9-η⁵-fluorenyl)dichlorozirconium ( 8 ). The last compound is a particularly poor terpolymerization catalyst; it incorporates very little VCH or HD and no ENB at all. 7 /MAO is a better catalyst for E/P/VCH terpolymerization, while 6 /MAO is superior in E/P/HD terpolymerization. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 319–328, 1998     

Ethylene propylene diene terpolymers produced with a homogeneous and highly active zirconium catalyst

EPDM terpolymers with ethylidene norbornene as diene monomer could be prepared by means of a soluble Ziegler catalyst formed from biscyclopentadienyl zirconium dimethyl and methylaluminoxane. The overall activities lie between 100 and 1000 kg EPDM/(molZr h bar), obtainable at zirconium concentrations as low as 5 × 10^?7 mol/L. After an induction period (0.5–5 h) the polymerization rates increased and then leveled to a value which was constant for several days. From copolymerization kinetics reactivity ratios r₁₂ = 31.5, r₂₁ = 5 × 10^?3, and r₁₃ = 3.1 could be derived, and by ¹³C-NMR spectroscopy r₁₂ · r₂₁ = 0.3 was found (1: ethylene, 2: propylene and 3: ethylidene norbornene). The regiospecifity of the catalyst toward propylene leads exclusively to the formation of head-to-tail enchainments. The diene polymerizes via vinyl polymerization of the cyclic double bond, and the tendency to branching is low. Molecular weights were estimated between 40,000 and 160,000. The average molecular weight distribution of 1.7 is remarkably narrow. Glass transition temperatures of ?60 to ?50°C could be observed. The cure behavior and the physical properties of cured samples were also tested.     

Zirconocenium cation catalysis of propene polymerization

rac-Ethylenebis(1-η⁵-indenyl)dimethylzirconium (1) was reacted with triphenylcarbenium tetrakis(pentafluorophenyl)borate (2) to produce in situ the rac-ethylenebis(indenyl)methylzirconium cation (3). This aluminium-free catalyst showed propene polymerization activity (A) and stereoselectivity which both increase with the decrease of polymerization temperature (T_p). At very low T_p, 3 behaved as a “single-site” catalyst. An efficient way to produce such cation is to react ansa-zirconocene dichloride with 2 in the presence of TEA (=triethylaluminium). A superior cationic catalyst was obtained from rac-dimethylsilylenebis(1-η⁵-indenyl)dichlorozirconium, 2, and TEA, which polymerizes propene at −20°C(−55°C) with activity of 2×10⁹ (3×10⁸) g polypropene per (mol Zr η mol C₃H₆ η h) to polypropenes which are 93.8% (99.4%) isotactic with melting temperature T_m = 152.6°C (159.9°C) and viscosity-average molecular weight M_v = 1.4×10⁵ (2.2×10⁵). The addition of methylaluminoxane lowers the A of the cationic catalyst especially at low T_p. Rigorously speaking, the cation derived from 1 or 3 behaves as a “single site” catalyst only at very low T_p. The use of TEA significantly and unexpectedly enhances the efficiency of the zirconocenium catalyst system.     

1-(2′-Deoxy-β-D-xylofuranosyl)cytosine: Base pairing of oligonucleotides with a configurationally altered sugar-phosphate backbone

Solid-phase synthesis of the oligo(2′-deoxynucleotides) 19 and 20 containing 2′-deoxy-β-D -xylocytidine ( 4 ) is described. For this purpose, 1-(2-deoxy-β-D -threo-pentofuranosyl)cytosine ( = 1-(2-deoxy-β-D -xylofuranosyl)-cytosine; 4 ) was protected at its 4-NH₂ group with a benzoyl (→ 5 ) or an isobutyryl (→ 8 ) residue, and a dimethoxytrityl group was introduced at 5′-OH (→ 7, 10 ; Scheme 2). Compounds 7 and 10 were converted into the 3′-phosphonates 11a,b . While 19 could be hybridized with 21 and 22 under formation of duplexes with a two-nucleotide overhang on both termini ( 19 · 21 : T_m 29°; 19 · 22 : T_m 22°), the decamer 20 bearing four xC_d residues could no longer be hybridized with one of the opposite strands. Moreover, the oligonucleotides d[(xC)₈? C] ( 13 ), d[(xC)₄? C] ( 14 ), d[C? (xC)₄? C] ( 15 ), and d[C? (xC)₃? C] ( 16 ) were synthesized. While 13 exhibits an almost inverted CD spectrum compared to d(C₉) ( 17 ), the other oligonucleotides show CD spectra typical for regular right-handed single helices. At pH 5, d[(xC)₈? C] forms a stable hemi-protonated duplex which exhibits a T_m of 60° (d[(CH⁺)₉] · d(C₉): T_m 36°). The thermodynamic parameters of duplex formation of ( 13H ⁺ · 13 ) and ( 17H ⁺ · 17 ) were calculated from their melting profiles and were found to be identical in ΔH but differ in ΔS ( 13H ⁺ · 13 : ΔS = ?287 cal/K mol; 17H ⁺ · 17 : ΔS = ?172 cal/K mol).     

ansa-Zirconocenium catalysis of syndiospecific polymerization of propylene: Theory and experiment

The syndiospecific propylene polymerizations catalyzed by isopropylidene(cyclopentadienyl)(fluorenyl)- and (2,2-dimethylpropylidene)(cyclopentadienyl)(fluorenyl)-zirconocenium ( 1 ⁺ and 2 ⁺) have been investigated theoretically and compared with experimental observations. With the ab initio calculated structures for the transition state (TS) of 1 ⁺(M)P and 2 ⁺(M)P (M = propylene, P = 2-methylpentyl), their steric energies (E°) have been computed using MM2 force-field. The difference between steric energies E°(m) and E°(r) for the meso and racemic enchainment of propylene, respectively, is defined as the stereocontrol energy [δE°(m ? r)] for syndiotactic propagation. The δE°(m ? r) for the TS of 1 ⁺ (M)P is about 2.1 kcal/mol, the value is 1 kcal/mol greater for 2 ⁺(M)P. The observed steric pentad distributions of the syndiotactic poly(propylene) obtained by these catalysts are consistent with smaller effective stereocontrol energy, which is about two-third as large as δE°(m ? r) values calculated for the MM2 optimized structure. Syndiotactic enchainment is favored over isotactic enchainment for all combinations of site configurations in the catalyst. α-Agostic interaction seems to enhance syndioselectivity, whereas γ-agostic interaction changes the stereoselectivity to meso enchainment. The mirror plane symmetry of the syndiotactic propagating species renders the stereoselectivity of the polymerization insensitive to reaction conditions. These catalysts are also highly regiospecific. © 1995 John Wiley & Sons, Inc.     

Olefin terpolymerizations. I. 1,4-hexadiene

Ethylene (E), propylene (P), and 1,4-hexadiene (HD) were terpolymerized with rac-1,2-ethylenebis (1-η⁵-indenyl) zirconium(IV) dichloride and methylaluminoxane (Et[Ind]₂ZrCl₂/MAO), and compared with the copolymerizations of E/P, E/HD, P/HD, and terpolymerization using ethylidene norbornene (ENB) as the termonomer. HD lowers the polymerization activity, the effect is more pronounced for P/HD and E/P/HD using large amount of P, than for E/HD and E/P/HD using feed low in P. The polymer molecular weight is most strongly affected by the temperature of polymerization (T_p), whereas the E/P ratio in the feed has virtually no effect. The reactivity ratios r_E and r_P are 3.0 and 0.3, respectively, at 20°C but r_P becomes larger than r_E at T_P = 70°C. ¹H-NMR spectra showed occurrence of cycloaddition in the homopolymerization of HD; on the other hand, HD is incorporated in the terpolymer only by linear 1,2-addition. © 1995 John Wiley & Sons, Inc.     

Kinetics of propylene polymerization initiated by rac‐Me2Si(1‐C5H2‐2‐Me‐4‐tBu)2Zr(NME2)2/MAO catalyst

The kinetics of propylene polymerization initiated by ansa‐metallocene diamide compound rac‐Me₂Si(CMB)₂Zr(NMe₂)₂ (rac‐1, CMB = 1‐C₅H₂‐2‐Me‐4‐^tBu)/methylaluminoxane (MAO) catalyst were investigated. The formation of cationic active species has been studied by the sequential NMR‐scale reactions of rac‐1 with MAO. The rac‐1 is first transformed to rac‐Me₂Si(CMB)₂ZrMe₂ (rac‐2) through the alkylation mainly by free AlMe₃ contained in MAO. The methylzirconium cations are then formed by the reaction of rac‐2 and MAO. Small amount of MAO ([Al]/[Zr] = 40) is enough to completely activate rac‐1 to afford methylzirconium cations that can polymerize propylene. In the lab‐scale polymerizations carried out at 30°C in toluene, the rate of polymerization (R_p) shows maximum at [Al]/[Zr] = 6,250. The R_p increases as the polymerization temperature (T_p) increases in the range of T_p between 10 and 70°C and as the catalyst concentration increases in the range between 21.9 and 109.6 μM. The activation energies evaluated by simple kinetic scheme are 4.7 kcal/mol during the acceleration period of polymerization and 12.2 kcal/mol for an overall reaction. The introduction of additional free AlMe₃ before activating rac‐1 with MAO during polymerization deeply influences the polymerization behavior. The iPPs obtained at various conditions are characterized by high melting point (approximately 155°C), high stereoregularity (almost 100% [mmmm] pentad), low molecular weight (MW), and narrow molecular weight distribution (below 2.0). The fractionation results by various solvents show that iPPs produced at T_p below 30°C are compositionally homogeneous, but those obtained at T_p above 40°C are separated into many fractions. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 737–750, 1999     

Synthesis of bromine-functionalized polyolefins by scandium-catalyzed copolymerization of 10-bromo-1-decene with ethylene,propylene, and dienes

By use of a THF-containing trimethylsilylmethyl scandium catalyst system (C₅Me₄SiMe₃)Sc(CH₂SiMe₃)₂(THF)/[Ph₃C][B(C₆F₅)₄], the multi-component copolymerization of 10-bromo-1-decene (BrDC) with ethylene, propylene, and dienes has been achieved to afford a new family of bromine-functionalized polyolefins with controllable composition and high molecular weight. The copolymerization of BrDC with ethylene afforded the well-defined BrDC–ethylene copolymers with high BrDC incorporation (up to 12 mol%) and high molecular weight (M_w > 100 kg mol⁻¹). The terpolymerization of propylene, ethylene with BrDC afforded random ethylene–propylene–BrDC terpolymers with controllable bromine content (2 ~ 11 mol%), high molecular weight (M_w > 100 kg mol⁻¹) and low glass transition temperature (T_g = −51 °C ~ −67 °C). Moreover, the tetrapolymerization of ethylene, propylene, BrDC, and ethylidene norbornene or conjugated dienes such as isoprene and myrcene has been achieved for the first time to afford selectively the bromine-functionalized ethylene–propylene–diene rubbers containing various types of double bonds.     

Influence of chemical exchange on the temperature dependence of Eu(fod)3-induced shifts

Temperature dependences of the paramagnetic shifts induced by Eu(fod)₃ in ¹H NMR spectra of ethylene oxide in carbon disulphide solution are obtained in the temperature range from +40 to ? 100°C at 100 MHz and from +30 to ?60°C at 60 MHz. The influence of chemical exchange leads to a decrease of the observed paramagnetic shifts with decreasing temperature. It is shown that a modified Swift and Connick equation can be used to describe the observed dependences. Upper limits of the mean lifetimes of the Eu(fod)₃-ethylene oxide adduct are τ_p < 1·7 × 10^?8 s at 14 °C and τ_p < 1 × 10^?8 s at 20 °C, respectively. The corresponding activation energy is equal to V_a = 13·7 kcal/mol.     

Radiation-induced copolymerization of methyl trifluoroacrylate with ethylene

Copolymerization of methyl trifluoroacrylate (MTFA) with ethylene in bulk was induced by γ irradiation. The copolymerization was observed to proceed in the liquid monomer mixture of MTFA and ethylene at 25°C with the dose rates ranging from 5.0 × 10⁴ to 1.0 × 10⁶ rad/hr. A wide range of the initial monomer composition gives an almost equimolar and alternating copolymer. The highest polymerization rate was observed at the equimolar monomer composition. The dose rate exponent of the polymerization rate is unity. The reactivity ratios of r₁ (MTFA) and r₂ (ethylene) were determined to be 0.034 and 0.14, respectively.     

Homo-and copolymerization of propylene and ethylene in the presence of titanium dichloride complexes with dioxolane dicarboxylate and bis(difurylmethanephenoxyimine) ligands

The polymerization of propylene and ethylene and the copolymerization of these olefins with postmetallocene catalysts [(4R,5R)-2,2-dimethyl-α,α,α′,α′-tetra(perfluorophenyl)-1,3-dioxolane-4,5-dimethanol] titanium(IV) dichloride and bis{N-(3,5-ditert-butylsalicylidene)-4-[bis(5-methyl-2-furyl)methyl]aniline}titanium( IV) dichloride have been studied. The polymerization of propylene and its copolymerization with ethylene have been carried out in a liquid monomer, while the polymerization of ethylene has been performed in toluene at the constant concentration of the monomer. Polymethylaluminoxane has been used as a cocatalyst. The activity of the catalysts in the polymerization of propylene and ethylene at 50°C is ～ 10 and ～45 kg PP/mol Ti h mol C₃H₆/l and 178.5 and 2700 kg PE/mol Ti h mol C₂H₄/l, respectively. It has been established that, in the copolymerization of propylene with ethylene, the active sites of both catalysts selectively polymerize ethylene. The resulting copolymers have a block structure (r ₁ r ₂= 4.6); as a result, the crystalline phase of polyethylene is formed in them. Polypropylene and propylene-ethylene copolymers are elastomeric materials. Polypropylene samples synthesized with [(4R,5R)-2,2-dimethyl-α,α,α′,α′-tetra(perfluorophenyl)-1,3-dioxolane-4,5-dimethanol]titanium(IV) dichloride demonstrate a high melting point (150–157°C) in combination with good elastic properties. Polyethylene is a linear polymer with the degree of crystallinity varying from 37 to 45% and a melting point of 133–134°C. The mechanical properties of the polymers and copolymers have been investigated.     

Thermally induced polymerization of isobutylene in the presence of SnCl4: Kinetic study of the polymerization and NMR structural investigation of low molecular weight products

The polymerization reactivity of isobutylene/SnCl₄ mixtures in the absence of polar solvent, was investigated in a temperature interval from −78 to 60 °C. The mixture is nonreactive below −20 °C but slow polymerization proceeds from −20 to 20 °C with the initial rate r₀ of the order 10⁻⁵ mol · l⁻¹ · s⁻¹. The rate of the process increases with increasing temperature up to ∼10⁻² mol · l⁻¹ · s⁻¹ at 60 °C. Logarithmic plots of r₀ and M̄_n versus 1/T exhibit a break in the range from 20 to 35 °C. Activation energy is positive with values E = 21.7 ± 4.2 kJ/mol in the temperature interval from −20 to 35 °C and E = 159.5 ± 4.2 kJ/mol in the interval from 35 to 60 °C. The values of activation enthalpy difference of molecular weights in these temperature intervals are ΔH_Mn = −12.7 ± 4.2 kJ/mol and −38.3 ± 4.2 kJ/mol, respectively. The polymerization proceeds quantitatively, the molecular weights of products are relatively high, M̄_n = 1500–2500 at 35 °C and about 600 at 60 °C. It is assumed that initiation proceeds via [isobutylene · SnCl₄] charge transfer complex which is thermally excited and gives isobutylene radical‐cations. Oxygen inhibits the polymerization from −20 to 20 °C. Possible role of traces of water at temperatures above 20 °C is discussed. It was verified by NMR analysis that only low molecular weight polyisobutylenes are formed with high contents of exo‐ terminal unsaturated structures. In addition to standard unsaturated groups, new structures were detected in the products. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1568–1579, 2000     

Novel Copolymers of 4-Fluorostyrene. 11. Some Ring-substituted 1,1-dicyano-2-(1-naphthyl)ethylenes

Novel copolymers of trisubstituted ethylene monomers, ring-substituted 1,1-dicyano-2-(1-naphthyl)ethylenes, RC₁₀H₆CH?C(CN)₂ (where R is H, 2-OCH₃, 4-OCH₃) and 4-fluorostyrene were prepared by solution copolymerization in the presence of a radical initiator (ABCN) at 70°C. The composition of the copolymers was calculated from nitrogen analysis, and the structures were analyzed by IR, ¹H and ¹³C-NMR. The order of relative reactivity (1/r ₁) for the monomers is (5.86) > 2-CH₃O (4.28) > 4-CH₃O (2.87). Relatively high T_g of the copolymers in comparison with that of poly(4-fluorostyrene) indicates a decrease in chain mobility of the copolymer due to the high dipolar character of the trisubstituted ethylene monomer unit. Decomposition of the copolymers in nitrogen occurred in two steps, first in the 200–500°C range with residue (7.3–7.7% wt.), which then decomposed in the 500–800°C range.     

Kinetics and mechanism of metallocene‐catalyzed olefin polymerization: Comparison of ethylene,propylene homopolymerizations,and their copolymerization

A series of ethylene, propylene homopolymerizations, and ethylene/propylene copolymerization catalyzed with rac‐Et(Ind)₂ZrCl₂/modified methylaluminoxane (MMAO) were conducted under the same conditions for different duration ranging from 2.5 to 30 min, and quenched with 2‐thiophenecarbonyl chloride to label a 2‐thiophenecarbonyl on each propagation chain end. The change of active center ratio ([C^*]/[Zr]) with polymerization time in each polymerization system was determined. Changes of polymerization rate, molecular weight, isotacticity (for propylene homopolymerization) and copolymer composition with time were also studied. [C^*]/[Zr] strongly depended on type of monomer, with the propylene homopolymerization system presented much lower [C^*]/[Zr] (ca. 25%) than the ethylene homopolymerization and ethylene–propylene copolymerization systems. In the copolymerization system, [C^*]/[Zr] increased continuously in the reaction process until a maximum value of 98.7% was reached, which was much higher than the maximum [C^*]/[Zr] of ethylene homopolymerization (ca. 70%). The chain propagation rate constant (k_p) of propylene polymerization is very close to that of ethylene polymerization, but the propylene insertion rate constant is much smaller than the ethylene insertion rate constant in the copolymerization system, meaning that the active centers in the homopolymerization system are different from those in the copolymerization system. Ethylene insertion rate constant in the copolymerization system was much higher than that in the ethylene homopolymerization in the first 10 min of reaction. A mechanistic model was proposed to explain the observed activation of ethylene polymerization by propylene addition. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 867–875     

Titanium and Zirconium Complexes with Non‐Salicylaldimine‐Type Imine–Phenoxy Chelate Ligands: Syntheses,Structures, and Ethylene‐Polymerization Behavior

New Ti and Zr complexes that bear imine–phenoxy chelate ligands, [{2,4‐di‐tBu‐6‐(RCH=N)‐C₆H₄O}₂MCl₂] ( 1 : M=Ti, R=Ph; 2 : M=Ti, R=C₆F₅; 3 : M=Zr, R=Ph; 4 : M=Zr, R=C₆F₅), were synthesized and investigated as precatalysts for ethylene polymerization. ¹H NMR spectroscopy suggests that these complexes exist as mixtures of structural isomers. X‐ray crystallographic analysis of the adduct 1 ?HCl reveals that it exists as a zwitterionic complex in which H and Cl are situated in close proximity to one of the imine nitrogen atoms and the central metal, respectively. The X‐ray molecular structure also indicates that one imine phenoxy group with the syn C?N configuration functions as a bidentate ligand, whereas the other, of the anti C?N form, acts as a monodentate phenoxy ligand. Although Zr complexes 3 and 4 with methylaluminoxane (MAO) or [Ph₃C]⁺[B(C₆F₅)₄]^?/AliBu₃ displayed moderate activity, the Ti congeners 1 and 2 , in association with an appropriate activator, catalyzed ethylene polymerization with high efficiency. Upon activation with MAO at 25 °C, 2 displayed a very high activity of 19900 (kg PE) (mol Ti)^?1 h^?1, which is comparable to that for [Cp₂TiCl₂] and [Cp₂ZrCl₂], although increasing the polymerization temperature did result in a marked decrease in activity. Complex 2 contains a C₆F₅ group on the imine nitrogen atom and mediated nonliving‐type polymerization, unlike the corresponding salicylaldimine‐type complex. Conversely, with [Ph₃C]⁺[B(C₆F₅)₄]^?/AliBu₃ activation, 1 exhibited enhanced activity as the temperature was increased (25–75 °C) and maintained very high activity for 60 min at 75 °C (18740 (kg PE) (mol Ti)^?1 h^?1). ¹H NMR spectroscopic studies of the reaction suggest that this thermally robust catalyst system generates an amine–phenoxy complex as the catalytically active species. The combinations 1 /[Ph₃C]⁺[B(C₆F₅)₄]^?/AliBu₃ and 2 /MAO also worked as high‐activity catalysts for the copolymerization of ethylene and propylene.     

Intrinsic Acid–Base Properties of a Hexa‐2′‐deoxynucleoside Pentaphosphate,d(ApGpGpCpCpT): Neighboring Effects and Isomeric Equilibria

The intrinsic acid‐base properties of the hexa‐2′‐deoxynucleoside pentaphosphate, d(ApGpGpCpCpT) [=(A1?G2?G3?C4?C5?T6)=(HNPP)^5?] have been determined by ¹H NMR shift experiments. The pK_a values of the individual sites of the adenosine (A), guanosine (G), cytidine (C), and thymidine (T) residues were measured in water under single‐strand conditions (i.e., 10 % D₂O, 47 °C, I=0.1 M , NaClO₄). These results quantify the release of H⁺ from the two (N7)H⁺ (G?G), the two (N3)H⁺ (C?C), and the (N1)H⁺ (A) units, as well as from the two (N1)H (G?G) and the (N3)H (T) sites. Based on measurements with 2′‐deoxynucleosides at 25 °C and 47 °C, they were transferred to pK_a values valid in water at 25 °C and I=0.1 M . Intramolecular stacks between the nucleobases A1 and G2 as well as most likely also between G2 and G3 are formed. For HNPP three pK_a clusters occur, that is those encompassing the pK_a values of 2.44, 2.97, and 3.71 of G2(N7)H⁺, G3(N7)H⁺, and A1(N1)H⁺, respectively, with overlapping buffer regions. The tautomer populations were estimated, giving for the release of a single proton from five‐fold protonated H₅(HNPP)^±, the tautomers (G2)N7, (G3)N7, and (A1)N1 with formation degrees of about 74, 22, and 4 %, respectively. Tautomer distributions reveal pathways for proton‐donating as well as for proton‐accepting reactions both being expected to be fast and to occur practically at no “cost”. The eight pK_a values for H₅(HNPP)^± are compared with data for nucleosides and nucleotides, revealing that the nucleoside residues are in part affected very differently by their neighbors. In addition, the intrinsic acidity constants for the RNA derivative r(A1?G2?G3? C4?C5?U6), where U=uridine, were calculated. Finally, the effect of metal ions on the pK_a values of nucleobase sites is briefly discussed because in this way deprotonation reactions can easily be shifted to the physiological pH range.     

Kinetics and mechanism of the anionic polymerization of cyclohexadienes initiated by naphthalene radical anions and dianions

The anionic polymerization of 1.3-cyclohexadiene (1.3-CHD) was investigated in temperatures that ranged from 25 to ?77°C. Initiation by lithium naphthalene (N^?·,Li⁺) in tetrahydrofuran at ?20°C yields polymers with fairly narrow molecular weight distribution. The M?_w of these polymers so prepared is ca. 20,000. Polymerization of 1.3-CHD conducted at room temperature is accompanied by the dehydrogenation and disproportionation of the monomer, especially when N^?·,K⁺ acts as initiator. Oligomers are formed when hexamethylphosphoramide is used as a solvent. The mechanism of the initiation of the polymerization of 1.3-CHD by N^?·,Li⁺ was elucidated and the rate constants at ?20°C in tetrahydrofuran of the elementary reactions were determined. It was established that the dianions formed by disproportionation of N^?·,Li⁺ act as effective initiators for 1.3-CHD. The adducts formed constitute the cyclohexanyl and naphthyl carbanionic groups. The former carbanions (λ_max ～ 275 nm) propagate the polymerization. The initially formed dimeric adducts are stabilized by the separation of the carbanionic end groups by the additional monomer units. Chain transfer to the monomer limits the growth of the polymers. The isomerization of the cyclohexadienyl anions, formed as result of chain transfer, may be followed by the elimination of lithium hydride. The latter reaction represents a termination step. Addition of 1.4-CHD to the reaction mixture enhances the chain transfer and the termination.     

Olefin copolymerization with metallocene catalysts. II. Kinetics,cocatalyst, and additives

The kinetics of ethylene/propylene copolymerization catalyzed by (ethylene bis (indeyl)-ZrCI₂/methylaluminoxane) has been investigated. Radiolabeling found about 80% of the Zr to be catalytically active. The estimates for rate constants at 50°C are k₁₁ = 1104 (M_s)^?1, k₁₂ = 430 (M_s)^?1, k₂₂ = 396 (M_s)^?1,k₂₁ = 1020 (M_s)^?1, and k^A_tr,1 + k^A_tr.2 = 1.9 × 10^?3 s^?1. Substitution of trimethylaluminum for methylaluminoxane resulted in proportionate decrease in polymerization rate. The molecular weight of the copolymer is slightly increased by loweing the [Al]/[Zr] ratio, or addition of Lewis base modifier but at the expense of lowered catalytic activity and increase in ethylene content in the copolymer. Lowering of the polymerization temperature to 0°C resulted in a doubling of molecular weight but suffered 10-fold reduction in polymerization activity and increase of ethylene in copolymer.