The preparation and characterization of poly(urethane–peo-polar siloxane) complexes as polymer electrolytes

A series of novel poly(urethane-PEO-polar siloxane) copolymers and their complexes with LiClO₄ were prepared for assessment as polymer electrolytes and characterized by IR, GPC, and DSC, and their ionic conductivity and thermal stability were tested. The incorporation of polar siloxanes into U-PEO greatly increased conductivity. The highest conductivity was 2.6 × 10^?5 S cm^?1 at 25°C. The correlation between T_g, conductivity, and the ratio of siloxane to PEO as well as stability of the polymers are discussed. © 1995 John Wiley & Sons, Inc.     

A macromonomer approach to the synthesis of poly(1,1‐bis(ethoxycarbonyl)‐2‐vinyl cyclopropane‐graft‐dimethyl siloxane)

Poly(1,1‐bis(ethoxycarbonyl)‐2‐vinyl cyclopropane (ECVP)‐graft‐dimethyl siloxane) copolymers were prepared using a macromonomer approach. Poly(dimethyl siloxane) (PDMS) macromonomers were prepared by living anionic polymerization of cyclosiloxanes followed by sequential chain‐end capping with allyl chloroformate. These macromonomers were then copolymerized with ECVP. MALDI‐ToF mass spectrometry and ¹H NMR spectroscopy were used to show that the macromonomers had approximately 80% of the end groups functionalized with allyl carbonate groups. Gradient polymer elution chromatography showed that high yields of the graft copolymers were obtained, along with only small fractions of the PECVP and PDMS homopolymers. Differential scanning calorimetry showed that the low glass transition temperature (T_g) of the PDMS component could be maintained in the graft copolymers. However, the T_g was a function of polymer composition and the polymers produced had T_gs that ranged from ?50 to ?120 °C. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

The preparation of novel silica modified polyimide membranes: synthesis,characterization, and gas separation properties

In this study, new monomers having siloxane groups were synthesized as an intermediate for preparation of siloxane modified polyimide polymers. Then with these monomers, the synthesis of uncrosslinked and crosslinked polyimide–siloxane hybrid polymer membranes were achieved. The purposes of the preparation of modified polyimides were to modify the thermal and chemical stability, and mechanical strength of polyimides, and to improve the gas separation properties of polymers. The new diamine monomer having siloxane groups was prepared from 3,5‐diaminobenzoic acid (3,5‐DABA) and 3‐aminopropyltrimethoxysilane (3‐APTMS) in N‐methyl‐2‐pyrollidone (NMP) at 180°C. The modified polyimide membranes having different amount of siloxane groups were synthesized from pyromellitic dianhydride (PMDA), 4,4‐oxydianiline (ODA), and 3,5‐diaminobenzamido‐N‐propyltrimethoxy silane (DABA/PTMS) in NMP using a two‐step thermal imidization process. The synthesis of modified polyimide membranes were characterized by Fourier transform infrared spectroscopy (FTIR). The thermal analysis of the polyimides were carried out by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Water absorption and swelling experiments were also carried out for the investigation of structural properties of polymers. FTIR observations confirmed that the polyimide membranes with new diamine intermediate were successfully obtained. Thermal analysis showed that the uncrosslinked copolyimides exhibited two glass transition temperatures, indicating that they were separated microphases and it was found that all the modified copolyimides had showed higher glass transition temperature (T_g) than unmodified polyimides. The separation properties of the prepared polyimide membranes were also characterized by permeability for O₂ and N₂ gases and ideal selectivity values were calculated. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis, structures and membrane properties of siloxane-imide co-polymers produced by aqueous polymerization

We report for the first time, the synthesis of siloxane-imide co-polymers by the reaction of mixtures of 1,4-bis(aminobutyl)tetramethyldisiloxane (ABTMDS) and 1,3-bis(4-aminophenoxy)benzene (TPE-R) with bisphenol A diphthalic anhydride (BPADA) using water as the polymerization solvent. A series of co-polymers were prepared incorporating 10, 20, 40 and 100 mol% of ABTMDS with the aromatic diamine TPE-R as the co-monomer. The synthesized co-polymers showed number average molecular weights in the range of 25,000–60,000. As expected the glass transition temperatures (T_gs) and moduli of the polymers were found to decrease with increasing amounts of the siloxane monomer and the homo-polymer containing only the siloxane diamine showing the lowest T_g (60 °C). The resulting polymers could be solution cast into strong and flexible membranes which showed significant decreases in water absorption and moisture permeability compared to the control polymer without siloxane groups. The polymers were characterized by FTIR, ¹³C and ¹H NMR, GPC, DSC and mechanical properties and structural comparisons were made with similar polymers made by standard solvent synthesis methods. Also cross-linked polymers were prepared by the reaction of ABTMDS with the aromatic homo-polymer control and their membrane properties were compared to those of the water synthesized siloxane co-polymers with a similar siloxane content.     

Polymerizable siloxane precursors having in-chain perfluoroalkyl groups

The synthesis and polymerization of several silphenylene siloxane polymer precursors containing a perfluoroalkylsegment in the backbone was carried out. The molecular weight characteristics of polymers from 1,3-bis[p(-hydroxydimethylsilyl)phenyl]hexafluoropropane and 1,3-bis[p(-dimethylaminodimethylsilyl)phenyl]hexafluoropropane were studied as a function of polymerization conditions. Polymers containing the dodecafluorohexane chain segment were also prepared. Polymers having inherent viscosities of 0.55 to 0.9 were obtained. The polymers crosslinked at room temperature to thermoset elastomers which were characterized by improved thermal and oxidative stability over dimethylsilicones. Room temperature swelling of the experimental polymers hydrocarbon solvents was also much lower than that of dimethylsilicones. The polymers containing the (CF₂)₃ and (CF₂)₆ linkages had glass transition points of ?12°C and ?34°C, respectively.     

Structure–property co‐relationship of fluorinated poly(imide‐siloxane)s

Eight poly(imide‐siloxane)s co‐polymers have been prepared by one pot solution imidization method. The polymers are synthesized by the reaction of bisphenol‐A‐dianhydride (BPADA) with fluorinated diamine 4,4′‐bis(3″‐trifluoromethyl‐p‐aminobiphenyl ether) biphenyl, and aminopropyl‐terminated polydimethylsiloxane (APPS). The polymers are synthesized by varying the siloxane loading to 5, 10, 15, 20, 25, 30, 35, and 40 wt%, respectively. Thermal, mechanical, rheological, and dielectric properties of these polymers have been evaluated with respect to siloxane loading. The polymers showed glass transition temperature of 107–203°C and tensile strength at break of 24–75 MPa depending on siloxane loading. The elongation break of the polymers ranges from 24 to 144% depending on siloxane loading. The amounts of char residue in the polymers have been correlated with incorporated siloxane in the polymer by NMR techniques. The polymers showed very low water absorption and dielectric constant as low as 2.43 when the siloxane loading is 40 wt%. Copyright © 2008 John Wiley & Sons, Ltd.     

Mesomorphic and luminescent properties of side chain nematic liquid-crystalline polymers containing Ir(III)

Iridium-containing liquid-crystalline polymers were obtained by graft copolymerisation using poly(methylhydrogeno)siloxane, 1-methyl-4-(4-(4-vinylcyclohexyl)cyclohexyl)benzene (M₁) and an iridium complexes monomer (Ir-M₂). The series of polymers contained different molecular fractions of Ir-M₂ from 0% to 1.2%. All of these polymers showed mesomorphic behaviours. The introduction of small amount of iridium ions endowed liquid-crystalline polymers with luminescent properties. The chemical structures were characterised by IR and ¹H NMR. The mesomorphic properties and phase behaviour were investigated by differential scanning calorimetry, thermal gravimetric analysis, polarising optical microscopy and X-ray diffraction. With an increase of iridium complexes units in the polymers, the glass transition temperature (T_g) did not change significantly; the isotropic temperature (T_i) decreased. All polymers showed typical nematic marble textures, which was confirmed by X-ray diffraction. The temperatures at which 5% weight loss occurred (T_d) were greater than 300°C for the polymers. The introduction of iridium complexes units did not change the liquid-crystalline state of polymer systems. With Ir³⁺ ion contents ranging between 0.6 and 2.4 mol%, luminescent intensity of polymers gradually increased.     

Polymerization of Si-containing acetylenes. XIV. Polymerization of diphenylacetylenes with bulky silyl groups and polymer properties

Polymerization and polymer properties of diphenylacetylenes with bulky silyl groups (SiMe₂–i-Pr, SiMe₂–t-Bu, SiMe₂Ph, SiEt₃) at para or meta position were studied under comparison with those of the SiMe₃ derivatives. The present monomers polymerized in good yields with TaCl₅-cocatalysts to form high molecular-weight polymers (M _w > 4 × 10⁵). The polymer yields of para-substituted monomers were similar to that of the SiMe₃ derivative, while those of meta substituted monomers were lower than that of m-SiMe₃ derivative. Most of the polymers were totally soluble in common solvents such as toluene and CHCl₃, although the polymers with p-SiMe₂–t-Bu and p-SiMe₂Ph groups were partly insoluble in all solvents. These polymers resembled SiMe₃-containing homologues in the UV-visible absorption and thermal stability. The oxygen permeability coefficients of these polymers were in the range of 10^?9?10^?8 cm³ (STP) cm/(cm²·s cm Hg)—lower than those of the corresponding SiMe₃-containing polymers. © 1993 John Wiley & Sons, Inc.     

Synthesis and properties of poly (diphenylacetylenes) having aliphatic para-substituents

1-(p-t-Butylphenyl)-2-phenylacetylene and 1-(p-n-butylphenyl)-2-phenylacetylene were polymerized in catalytic systems based on TaCl₅ to give new polymers in high yields. These monomers were more reactive than diphenylacetylene (DPA) in copolymerization. Unlike poly (DPA), the present polymers were soluble in toluene, CHCl₃, etc. owing to the high configurational entropy induced by the para-substituents. Their relative weight-average molecular weights determined by GPC were in the range of 6 × 10⁵–36 × 10⁵, and films could be obtained by solution casting. These polymers were fairly thermally stable, as seen from their high onset temperatures (320–380°C) of weight loss in TGA in air. The oxygen permeability coefficient of the polymer with t-Bu group was 1100 barrers, the highest among those of all the hydrocarbon polymers. © 1994 John Wiley & Sons, Inc.     

Synthesis of new linear polymers containing phosphorus atom in the main chain by the radical polyaddition: Addition polymers of phenylphosphine with 1,4-divinylbenzene or 1,4-diisopropenylbenzene and their properties

A polyaddition of phenylphosphine (PH) to 1,4-divinylbenzene (DVB) or 1,4-diisopropenylbenzene (DIPB) was carried out by radical initiations or UV irradiation at 60–80°C in toluene under a nitrogen atmosphere. The soluble polymer with higher molecular weight () was obtained in a high yield with AIBN initiator for 95 h in the presence of 5% excess of PH to DVB (monomer feed ratio [DVB]₀/[PH]₀ = 1/1.05). On the other hand, a polyaddition of PH to DIPB proceeded much slower than the case of DVB, but the high polymer was obtained in a high yield by choosing polyaddition conditions such as polyaddition temperature and initiator concentration. From ¹H-NMR, IR analyses, and phosphorus content of the polymers, it was characterized that both polymers have the alternating structure consisting of PH and DVB or DIPB units in 1 : 1 ratio. The glass transition and decomposition temperatures of both polymers under a nitrogen atmosphere were almost similar: 15–30°C and 380–385°C, respectively; but, the polymers were oxidized by heating under an atmosphere of air. The polymers had a self-extinguishing property and the polymer blend of the flammable polymers such as polystyrene and polyethylene with the phosphorus-containing polymers exhibited an excellent flame resistance. © 1994 John Wiley & Sons, Inc.     

Synthesis and characterization of liquid crystalline elastomers bearing fluorinated mesogenic units and crosslinking mesogens

Several new side‐chain liquid crystalline (LC) polysiloxanes and elastomers ( IP ‐ VIP ) bearing fluorinated mesogenic units and crosslinking mesogens were synthesized by a one‐step hydrosilylation reaction with poly(methylhydrogeno)siloxane, a fluorine‐containing LC monomer 4′‐undec‐10‐enoyloxy‐biphenyl‐4‐yl 4‐fluoro‐benzoate and a crosslinking LC monomer 4′‐(4‐allyloxy‐benzoxy)‐biphenyl‐4‐yl 4‐allyloxy‐benzoate. The chemical structures and LC properties of the monomers and polymers were characterized by use of various experimental techniques such as FTIR, ¹H‐NMR, EA, TGA, DSC, POM and XRD. The effect of crosslinking mesogens on mesomorphic properties of the fluorinated LC polymers was studied as well. The obtained polymers and elastomers were soluble in many solvents such as toluene, tetrahydrofuran, chloroform, and so forth. The temperatures at which 5% weight loss occurred (T_d) were greater than 250°C for all the polymers, and the weight of residue near 600°C increased slightly with increase of the crosslinking mesogens in the fluorinated polymer systems. The samples IP , IIP , IIIP and IVP showed both smectic A and nematic phases when they were heated and cooled, but VP and VIP exhibited only a nematic mesophase. The glass transition temperature (T_g) of polymers increased slightly with increase of crosslinking mesogens in the polymer systems, but the mesophase–isotropic phase transition temperature (T_i) and smectic A–nematic mesophase transition temperature (T_S‐N) decreased slightly. It suggests that the temperature range of the mesophase became narrow with the increase of crosslinking mesogens for all the fluorinated polymers and elastomers. In XRD curves, the intensity of sharp reflections at low angle decreased with increase of crosslinking mesogens in the fluorinated polymers systems, indicating that the smectic order derived from fluorinated mesogenic units should be destroyed by introduction of more crosslinking mesogens. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and absorption/emission properties of novel poly(silylenearylenevinylene)s

Polymerization of p-(dimethylsilyl)phenylacetylene in toluene at 25 and 80 °C with RhI(PPh₃)₃ catalyst afforded highly regio- and stereoregular poly(dimethylsilylene-1,4-phenylenevinylene)s [cis- and trans-poly( 1a )s] containing 98% cis- and 99% trans-vinylene moieties, respectively. The trans-type polymers exhibited redshifts and hyperchromic effects in the ultraviolet–visible spectrum as compared with the cis-type counterparts. Photoirradiation of cis- and trans-poly( 1a )s gave cis-rich mixtures at equilibrium states. The trans and cis polymers exhibited different emission properties, for example—trans polymer, emissn λ_max = 400 nm, quantum yield: 3.4 × 10⁻³ and cis polymer, emissn λ_max = 380 nm, quantum yield: 1.5 × 10⁻³. Besides poly( 1a ), poly(dimethylsilylenearylenevinylene)s containing biphenylene and phenylenesilylenephenylene units [poly( 3 )] were prepared. The extent of conjugation in these polymers decreased in the orders of biphenylene > phenylene > phenylenesilylenephenylene as well as trans-vinylene > cis-vinylene. The quantum yield of the trans-rich polymer with biphenylene moiety was fairly large and 0.15. Polyaddition of 1,4-bis(dimethylsilyl)benzene and three types of diethynylarenes (4,4′-diethynylbiphenyl, 2,7-diethynylfluorene, and 2,6-diethynylnaphthalene) catalyzed by RhI(PPh₃)₃ provided novel regio- and stereoregular polymers [poly( 6 )]. These polymers displayed blue light emission with high quantum yields (4–81%). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3615–3624, 2003     

Poly(silarylene–siloxane)polyimides from allyl‐terminated oligoimides and hydride‐functional silarylene–siloxanes via hydrosilylation polymerization

This research was focused on the design and execution of new synthetic routes to low‐temperature‐curable poly(silarylene–siloxane)polyimides. The synthesis of individual oligoimide and silarylene–siloxane blocks was followed by hydrosilylation polymerization to produce crosslinked copolymers. The silarylene–siloxane and polyimide blocks were structurally characterized by IR and ¹H NMR spectroscopy and size exclusion chromatography. The high‐temperature resistance of the copolymers was evaluated through the measurement of heat distortion temperatures (T_HD's) via thermomechanical analysis and by the determination of the weight loss at elevated temperatures via thermogravimetric analysis. Glass‐transition temperatures (T_g's) of the silarylene–siloxane segments were measured by differential scanning calorimetry. Hydrosilylation curing was conducted at 60 °C in the presence of chloroplatinic acid (H₂PtCl₆). The copolymers displayed both high‐temperature resistance and low‐temperature flexibility. We observed T_g of the silarylene–siloxane segment as low as ?77 °C and T_HD of the polyimide segment as high as 323 °C. The influence of various oligoimide molecular weights on the properties of copolymers containing the same silarylene–siloxane was examined. The effect of various silarylene–siloxane molecular weights on the properties of copolymers containing the same oligoimide was also examined. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4922–4932, 2005     

Solubility of carbon dioxide,methane, and propane in silicone polymers. Effect of polymer backbone chains

The solubility of carbon dioxide, methane, and propane in poly(dimethyl silmethylene) [(CH₃)₂SiCH₂]_x and poly(tetramethyl silhexylene siloxane) [(CH₃)₂Si (CH₂)₆Si (CH₃)₂O]_x was measured in the temperature range from 10.0 to 55.0°C and at elevated pressures. The present results are compared with similar measurements made with other silicone polymers. At a given temperature and pressure, the solubility of the above three gases is highest in poly(dimethyl siloxane) (Me₂SiO)_x. The gas solubility is decreased by either backbone-chain or side-chain substitutions of functional groups in (Me₂SiO)_x which increase the stiffness of the polymer chains and decrease the specific or fractional free volume of the polymers. It is conjectured that a decrease in the free volume of silicone polymers has a greater effect in decreasing the gas solubility than differences in gas/polymer interactions [with the exception of specific interactions (e.g., between CO₂ and polar groups in the polymer)]. © 1993 John Wiley & Sons, Inc.     

Synthesis and characterization of fluorene‐based copolymers containing siloxane or distilbene moieties on their main chain

Two novel types of polyfluorene copolymers containing siloxane linkages or distilbene moieties on their main‐chains were synthesized by Ni(0)‐mediated Yamamoto coupling polymerization. These polymers, designated P2Silo05, P2Silo15, PF‐P02, and PF‐P05 were prepared by copolymerization between 2,7‐dibromo‐9,9′‐dihexylfluorene and bis(bromobenzene)‐terminated disiloxane monomer (for P2Silo05 and P2Silo15) or dibromodistilbene monomer (for PF‐P02 and PF‐P05). All of the polymers were highly soluble in common organic solvents such as chloroform, toluene, and p‐xylene. The glass transition temperatures of the polymers were between 92 and 113 °C, and the decomposition temperatures for a 5% weight loss (T_d) were above 420 °C for all of the polymers, demonstrating high thermal stability. The molecular weight (M_w) of the polymers ranged from 4.2 × 10⁴ to 8.8 × 10⁴. The blue shift of the maximum in the UV‐visible absorption was greater in polymers with a higher molar percentage of siloxane linkages or distilbene moieties than in homo poly (dihexylfluorene) (PDHF). However, the photoluminescence spectra of the polymers were similar to those of PDHF in terms of the onsets and patterns. Single‐layer light‐emitting diodes were fabricated with a configuration of ITO/PEDOT:PSS/polymers/Ca/Al. The maximum electroluminescence emission wavelengths of the polymers were 425–450 nm, corresponding to pure blue light. The CIE co‐ordinates of the polyfluorenes containing siloxane linkages or distilbene moieties ranged from (0.21, 0.21) to (0.17, 0.10), indicating deeper blue light than that of PDHF {CIE co‐ordinates of (0.25, 0.29)}, with P2Silo15 giving the deepest blue‐light {CIE co‐ordinates of (0.17, 0.10)}. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1595–1608, 2009     

Tuning the frontier molecular orbital energy levels of n‐type conjugated copolymers by using angular‐shaped naphthalene tetracarboxylic diimides,and their use in all‐polymer solar cells with high open‐circuit voltages

An angular‐shaped naphthalene tetracarboxylic diimide (NDI) was designed and synthesized as a new building block for n‐type conjugated polymers to tune their energy levels. Three n‐type copolymers incorporating this angular‐shaped NDI as the acceptor moiety were obtained by Stille coupling reactions and had number average molecular weights of 18.7–73.0 kDa. All‐polymer bulk‐heterojunction solar cells made from blends of these polymers with poly(3‐hexylthiophene) gave a power conversion efficiency up to 0.32% and exhibited an open‐circuit voltage (V_oc) up to 0.94 V due to their relative high‐lying lowest unoccupied molecular orbital energy levels. The high V_oc of 0.94 V is higher than that of solar cells based on linear‐shaped NDI‐containing polymers (<0.6 V). The results indicate that the angular‐shaped NDI is a promising building block for constructing nonfullerene polymer acceptors for solar cells with high open‐circuit voltages. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of regiocontrolled poly(4,6-di-n-butoxy-1,3-phenylene) by oxidative coupling polymerization

Poly(4,6-di-n-butoxy-1,3-phenylene) ( 6 ) was prepared by oxidative coupling polymerization of 1,3-di-n-butoxybenzene ( 1 ) or 2,2′,4,4′-tetra-n-butoxy biphenyl (3). Polymerizations were conducted in nitrobenzene in the presence of FeCl₃ at room temperature and produced polymers with number-average molecular weights up to 42,000. The effects of various factors, such as amount of FeCl₃ and reaction temperature and time were studied. The structure of polymer 6 was characterized by 270 MHz ¹H- and 68.5 MHz ¹³C-NMR spectroscopies and was estimated to consist of almost completely 1,3-linkage. The regiocontrolled polymer was readily soluble in common organic solvents. Thermogravimetric analysis of polymer 6 showed 10% weight loss at 390°C in nitrogen. © 1997 John Wiley & Sons, Inc. J Polym Chem 35 : 2259–2266, 1997     

Diacetylene–siloxane–carborane thermosets and ceramic precursors

Thermosets and ceramic chars were prepared and characterized from a diacetylene–siloxane–carborane polymer, DSCS, and a diacetylene–siloxane polymer, DS. The goal was to incorporate the known thermo‐oxidative stability found in the siloxane–carborane elastomers into high‐performance thermosets and ceramic chars. The DSCS thermoset had excellent thermo‐oxidative stability as determined by a low weight loss and tough residue after annealing for 100 h in air at 300 °C, but it had a low glass transition temperature (94 °C). The DS thermoset did not undergo a glass transition below 350 °C and had a low weight loss on thermo‐oxidative aging, but the residue was quite brittle. Two random copolymers were made to optimize the thermo‐oxidative stability and toughness of the DSCS thermoset and the higher glass transition of the DS thermoset. Significantly, the 50:50 DSCS/DS random copolymer when cured to a thermoset did not undergo a glass transition below 350 °C, yet retained much of the strength, toughness and thermo‐oxidative stability of the DSCS thermoset. Heat treatment of the poly‐DSCS to elevated temperatures resulted in a ceramic material with improved properties relative to the ceramic derived from poly‐DS. Both polymers had similar char yields to 800 °C, but the poly‐DSCS solidified to a 15% denser ceramic. Copyright © 2000 John Wiley & Sons, Ltd.     

Synthesis of novel polymer containing selenium by radical addition polymerization of 1,4-benzenediselenol to 1,4-divinylbenzene

A novel addition polymerization of 1,4-benzenediselenol (BDSe) to 1,4-divinylbenzene (DVB) was carried out with various azo radical initiators [dimethyl 2,2′-azobisisobutyrate (DAIB), 1,1′-azobis(1-acetoxy-1-phenylethane) (AAPE), and AIBN] in toluene at 65 and 75°C under a nitrogen atmosphere. The polymerization proceded without an induction period, and pale-yellowish powder polymers were obtained in 89% yields for 75 h (DAIB), 89% yields for 24 h (AAPE), and 60% yields for 8 h (AIBN). The molecular weight (M_w) of the insoluble polymers in toluene was about 4000 (IBN) to 14,000 (DAIB or AAPE) by GPC. The polymer had an alternating structure of BDSe to DVB units by ¹H-NMR, IR analyses, and selenium contents, but the polymer contained the diselenide linkage by Raman spectroscopy. By AIBN initiator, the yield of the polymers did not increase over 60% and higher molecular weight polymer was hardly obtained. According to the model addition reaction of benzeneselenol to styrene by AIBN, it was found that AIBN was consumed by the side reaction between dimethyl-N-(2-cyano-2-propyl)ketenimine derivedAppl 11 from AIBN and benzeneselenol to give the adduct C, MH⁺ 295 by DCI MS. On the other hand, DAIB and AAPE initiators, which do not form a ketenimine intermediate, gave the polymers of higher molecular weight in a higher yield. The polymer film exhibited high refractive index (n²⁵_D = 1.81) and a reversible phase transition between a transparency and an opaque by thermal mode. © 1994 John Wiley & Sons, Inc.     

Preparation and properties of polybenzoxazine/poly(imide‐siloxane) alloys: In situ ring‐opening polymerization of benzoxazine in the presence of soluble poly(imide‐siloxane)s

Benzoxazine monomer (Ba) was blended with soluble poly(imide‐siloxane)s in various weight ratios. The soluble poly(imide‐siloxane)s with and without pendent phenolic groups were prepared from the reaction of 2,2′‐bis(3,4‐dicarboxylphenyl)hexafluoropropane dianhydride with α,ω‐bis(aminopropyl)dimethylsiloxane oligomer (PDMS; molecular weight = 5000) and 3,3′‐dihydroxybenzidine (with OH group) or 4,4′‐diaminodiphenyl ether (without OH group). The onset and maximum of the exotherm due to the ring‐opening polymerization for the pristine Ba appeared on differential scanning calorimetry curves around 200 and 240 °C, respectively. In the presence of poly(imide‐siloxane)s, the exothermic temperatures were lowered: the onset to 130–140 °C and the maximum to 210–220 °C. The exotherm due to the benzoxazine polymerization disappeared after curing at 240 °C for 1 h. Viscoelastic measurements of the cured blends containing poly(imide‐siloxane) with OH functionality showed two glass‐transition temperatures (T_g's), at a low temperature around ?55 °C and at a high temperature around 250–300 °C, displaying phase separation between PDMS and the combined phase consisting of polyimide and polybenzoxazine (PBa) components due to the formation of AB‐crosslinked polymer. For the blends containing poly(imide‐siloxane) without OH functionalities, however, in addition to the T_g due to PDMS, two T_g's were observed in high‐temperature ranges, 230–260 and 300–350 °C, indicating further phase separation between the polyimide and PBa components due to the formation of semi‐interpenetrating networks. In both cases, T_g increased with increasing poly(imide‐siloxane) content. Tensile measurements showed that the toughness of PBa was enhanced by the addition of poly(imide‐siloxane). Thermogravimetric analysis showed that the thermal stability of PBa also was enhanced by the addition of poly(imide‐siloxane). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2633–2641, 2001