Simultaneous determination of organotin,organolead, and organomercury compounds in environmental samples using capillary gas chromatography with atomic emission detection

As part of a continuing evaluation of new analytical and sample preparation techniques conducted by the US Environmental Protection Agency (EPA), the use of capillary gas chromatography with atomic emission detection (GC-AED) for the simultaneous determination of organotin, organolead, and organomercury compounds in environmental samples was investigated. Pentylmagnesium bromide was used to pentylate ionic organotin, organolead, and organomercury compounds; the pentyl derivatives were then separated by GC and determined by AED. Several important GC-AED parameters, including the type of injector inlet, carrier gas flow rate, and helium make-up gas flow rate, were optimized for the simultaneous determination of these organometallic compounds. Their minimum detectable concentrations were approximately 1.0 to 2.5 ng/mL using a 0.5-μL on-column injection. The calibration curves exhibited good linearity between 2.5 and 2500 ng/mL for organotin and organolead compounds, and between 2.5 and 10000 ng/mL for organomercury compounds.     

Element-selective atomic emission detection for capillary GC of metal-containing compounds

Element-selective GC detection by microwave-induced plasma atomic emission spectroscopy has been used to examine a wide variety of compounds containing metals, non-metals, and metalloids. “Recipes”, or new selective detection schemes for use with the software of the computer-controlled system, have been developed for the selective detection of boron, aluminum, gallium, titanium, vanadium, chromium, manganese, rhenium, palladium, and platinum. Figures of merit including limits of detection, linear dynamic range, and spectral selectivity over carbon have been established for most of these elements. Gas chromatography – atomic emission detection (GC-AED) has been applied to the selective detection of vanadium, nickel, and iron in metalloporphyrins present in crude oil, manganese-selective detection of methylcyclopentadienylmanganese tricarbonyl (MMT) in gasoline, and titanium-selective detection of reaction mixtures containing titanium catalysts or titanium boride molecular precursors.     

Element-selective detection using capillary gas chromatography with atomic emission detection

Capillary GC coupled to an atomic emission detector (AED) provides a powerful new hyphenated technique for the separation and characterization of complex mixtures and compounds. The AED provides simultaneous and truly specific multi-element detection. The specificity of detection reduces the need for the complex sample pretreatment procedures which are necessary to reduce the interference from co-eluted substances which is experienced with detectors such as the FID and the ECD. A range of environmentally significant problems has been studied, including PCB analysis, the characterization of the reaction products of a novel waste treatment process, and the profiling of sulfur-containing species formed by the pyrolysis of various types of coal.     

Improvements in the methylmercury extraction from human hair by headspace solid-phase microextraction followed by gas-chromatography cold-vapour atomic fluorescence spectrometry

Improvements in the methylmercury extraction from human hair by solid-phase microextraction followed by gas chromatography coupled to cold-vapour atomic fluorescence spectrometry (GC-CVAFS) have been carried out. They consisted in the optimisation of the digestion step prior to the aqueous-phase ethylation and in the GC-CVAFS interface set-up. The main digestion parameters such as acid type, concentration, temperature and time have been optimised for hair sample analysis, thereby avoiding methylmercury degradation. Moreover, the stability of the digested samples was evaluated to improve the sample throughput.     

On-line preconcentration for capillary electrophoresis-atomic fluorescence spectrometric determination of arsenic compounds

An on-line preconcentration method was developed for capillary electrophoresis (CE) with hydride generation-atomic fluorescence spectrometric (HG-AFS) detection of arsenite, arsenate, dimethylarsenic acid, and monomethylarsenic acid. These arsenic species were negatively charged in the sample solution with high pH. When the potential was applied to the electrophoretic capillary, the negatively charged analyte ions moved faster and stacked at the boundary of sample and CE buffer with low pH. So, high sample pH in combination with low buffer pH allowed the injection of large sample volumes (approximately 1100 nL). Comparison of the preconcentration of analyte solution, prepared with doubly deionized water and that prepared with lake or river water, indicated that preconcentration was independent on the original matrix. With injection of approximately 1100 nL sample, an enrichment factor of 37-50-fold was achieved for the four species. Detection limits for the four arsenic species ranged from 5.0 to 9.3 microg.L(-1). Precisions (RSDs, n = 5) were in the range of 4.9-6.7% for migration time, 4.7-11% for peak area, and 4.3-7.1% for peak height, respectively. The recoveries of the four species in locally collected water solution spiked with 0.1 microg.mL(-1) (as As) ranged from 83 to 109%.     

Determination of organotin compounds in environmental samples by supercritical fluid extraction and gas chromatography with atomic emission detection

The extraction of six tetraalkyltin and seven ionic organotin compounds from spiked topsoil samples with supercritical carbon dioxide and carbon dioxide modified with 5 percent methanol was investigated. Analysis of the soil extracts was performed by gas chromatography with atomic emission detection. Retention times, minimum detectable concentrations, and detector linear ranges are included for nine organotin compounds (seven of the nine compounds were derivatized with n-pentylmagnesium bromide prior to gas chromatographic analysis). A 2³ factorial experimental design was used to study the effect of three variables (pressure, temperature, and extraction time) on compound recovery. The results indicate that the tetraalkyltin compounds are extracted from topsoil samples with recoveries ranging from 90 to 110 percent. Recoveries for the ionic organotin compounds ranged from 50 to 75 percent for trimethyltin chloride, triethyltin bromide, and tributyltin iodide; they were below 20 percent for dimethyltin dichloride, dibutyltin dichloride, diphenyltin dichloride, and butyltin trichloride. When sodium diethyldithiocarbamate was added to the soil samples prior to extraction, followed by extraction with carbon dioxide modified with 5 percent methanol, recoveries ranged from 70 to 90 percent for trimethyltin chloride, triethyltin bromide, dimethyltin dichloride, tributyltin iodide, and dibutyltin dichloride; recoveries were approximately 40 percent for butyltin trichloride and diphenyltin dichloride.     

Determination of aluminum in serum by capillary zone electrophoresis with laser-induced fluorescence detection

Summary A novel method of separating and detecting trace aluminum by capillary zone electrophoresis is described. Aluminum is reacted with lumogallion [4-chloro-3-(2,4-dihydroxyphenylazo)-2-hydroxybenzen-1-sulphonic acid] so that the complex can be selectively and sensitively detected by a laser-induced fluorescence detector after capillary electrophoretic separation. Using the proposed method, limits of detection in the sub parts per billion range are achieved. The technique is applied to the determination of aluminum in human serum.     

Determination of chlorinated and brominated micropollutants by capillary gas chromatography coupled with on-column radio frequency plasma atomic emission detection

Capillary gas chromatography (GC) combined with on-column radio frequency plasma atomic emission detection was evaluated for the determination of polychlorinated and polybrominated biphenyls (PCBs and PBBs). Quantitation was possible utilizing a single chlorine or bromine calibration curve based on a randomly selected reference compound, because the signal per ng of halogen ranged within 17 % for 29 congeners. Combined with an internal standard to correct for potential plasma quenching from matrix components, this type of universal quantitation represented a sub-stantial simplification of current calibration procedures. In combi-nation with relatively low detection limits (1–5 pg/s of halogen), the present work suggested that GC, coupled with on-column atomic emission detection is a promising technique for the determination of halogenated micropollutants.     

Speciation of organotin compounds in waters and marine sediments using purge-and-trap capillary gas chromatography with atomic emission detection

A procedure for the simultaneous determination of six organotin compounds, including methyl-, butyl- and phenyltins, in waters and marine sediments is developed. The analytes were leached from the solid samples into an acetic acid:methanol mixture by using an ultrasonic probe. The organotins were derivatized with sodium tetraethylborate (NaBEt₄) in the aqueous phase, stripped by a flow of helium, pre-concentrated in a trap and thermally desorbed. This was followed by capillary gas chromatography with microwave-induced plasma atomic emission spectrometry as the detection system (GC-AED). Each chromatographic run took 22 min, including the purge time. Calibration curves were obtained by plotting peak area versus concentration and the correlation coefficients for linear calibration were at least 0.9991. Detection limits ranged from 11 to 50 ng Sn l⁻¹ for tributyltin and tetramethyltin, respectively. The seawater samples analyzed contained variable concentrations of mono-, di- and tributyl- and monophenyltin, ranging from 0.05 to 0.48 μg Sn l⁻¹, depending on the compound. Some of the sediments analyzed contained concentrations of dibutyl- and tributyltin of between 6.0 and 13.0 ng Sn g⁻¹. Analysis of the certified reference material PACS-2, as well as of spiked water and sediment samples showed the accuracy of the method. The proposed method is selective and reproducible, and is considered suitable for monitoring organotin compounds in water and sediment samples.     

Indirect laser-induced fluorescence detection of diuretics separated by capillary electrophoresis

Indirect LIF detection was applied to the detection of four acidic diuretics separated by CZE. Semiconductor laser was employed to provide the stable excitation of 473 nm. With an optimized electrophoretic buffer system which contained 5 mM of triethylamine, 0.1 microM of fluorescein, and 5% of n-butanol, fast separation of four diuretics (ethacrynic acid, chlorthalidone, bendroflumethiazide, and bumetanide) can be performed within 3 min with the detection limits of 0.2-2 microg/mL. The impacts of buffer components including the concentrations of the electrolytes, fluorescence probe, and the organic additives were demonstrated. The method was applied for the detection of diuretics in urine. As an alternative way for the fast analysis of diuretics, this indirect detection method provided the technical support for future microchip performances, in which diuretics may be detected in the microchip by the common LIF detector without derivatization.     

Environmental applications of capillary gas chromatography coupled with atomic emission detection — a review

Environmental applications of capillary gas chromatography coupled with atomic emission derection (GC-AED) have been reviewed with emphasis on both the commercial and laboratory-built systems. Attention was focused on (1) element-selective detection of non-metallic as well as metallic pollutants, (2) identification of contaminants, and (3) sample preparation considerations.     

Analysis of amine compounds by capillary gas chromatography using ammonia–helium carrier gas

The use of 10%, 1%, and 0.1% ammonia in helium as carrier gas was investigated as a means of improving poor chromatographic peak shape often associated with low level determinations of amine compounds using thin film capillary columns. The 1% ammonia in helium was found suitable for improving the peak shape of sterically unhindered amine compounds, such as urethane and certain aliphatic primary amines, during gas chromatographic analysis on thin film columns. There was a negligible effect on the peak tailing arising on thick film columns. The 0.1% ammonia in helium was suitable, but not as efficient as the 1% ammonia in helium, in eliminating the peak tailing associated with low level analysis of amine compounds. The signal-to-noise (S/N) ratio improved from < 1 using helium carrier gas to 20–25 (for certain test amine compounds) using 1% ammonia in carrier gas. The 10% ammonia in helium carrier gas had an effect on the chromatographic performance similar to that of the 1% ammonia in helium, but the baseline level was very high and this mixture was not used in further studies.     

Analysis of serotonin in brain microdialysates using capillary electrophoresis and native laser-induced fluorescence detection

Serotonin or 5-hydroxytryptamine (5-HT) is a major neurotransmitter in the central nervous system. In this work, a method for analyzing 5-HT in brain microdialysis samples using a commercially available capillary electrophoresis (CE) system has been developed. A pH-mediated in-capillary preconcentration of samples was performed, and after separation by capillary zone electrophoresis, native fluorescence of 5-HT was detected by a 266 nm solid-state laser. The separation conditions for the analysis of 5-HT in standard solutions and microdialysates have been optimized, and this method has been validated on both pharmacological and analytical bases. Separation of 5-HT was performed using a 80 mmol/L citrate buffer, pH 2.5, containing 20 mmol/L hydroxypropyl-beta-cyclodextrin (HP-beta-CD) and +30 kV voltage. The detection limit was 2.5 x 10(-10) mol/L. This method allows the in vivo brain monitoring of 5-HT using a simple, accurate CE measurement in underivatized microdialysis samples.     

Fast analysis of oxygen and sulfur compounds in gasoline by GC-AED

This paper describes a method for determining both the total sulfur content and the concentration of oxygenated additives in gasoline by gas chromatography with atomic emission detection (GC-AED). The AED provides selective detection of oxygen and sulfur compounds. Because the response factors for sulfur and oxygen are largely independent of the type of compound, calibration and determination of total element content are simplified. The use of a 0.1 mm i.d. capillary column enables complete elution of the components of the gasoline in under 10 minutes.     

Sensitive determination of rhodamine 110-labeled monosaccharides in glycoprotein by capillary electrophoresis with laser-induced fluorescence detection

Rhodamine 110 (Rho110) has been used in the highly sensitive analysis of monosaccharides, as it reacts with the reducing carbonyl group of the saccharides. The monosaccharide derivatives were investigated by capillary electrophoresis with laser-induced fluorescence detection. The derivatization was performed at 90 °C for 30 min for all monosaccharides. The derivatized monosaccharides were separated using 200 mM borate (pH 10.5) as running buffer within 20 min. The fluorescence intensities of Rho110-derivatives were significantly decreased by the presence of excess reducing agent, but were greatly increased by the addition of potassium hexacyanoferrate(III). The concentration and mass detection limits for monosaccharides were in the range of 1.4–2.8 nM and 36–70 amol, respectively. We have applied this derivatization method to the analysis of the composition of monosaccharides in glycoproteins (ribonuclease B, fetuin, and erythropoietin) following their subjection to strong acid hydrolysis. The results from these analyses were in good agreements with the reported values established previously.     

Lamp-based native fluorescence detection of proteins in capillary electrophoresis

The potential of a recently developed lamp-based fluorescence detector for the analysis of underivatised proteins by capillary electrophoresis (CE) was investigated. Fluorescence detection (Flu) was achieved using optical light guides to deliver excitation light from a Xenon–Mercury lamp to the capillary detection window and to collect fluorescence emission and lead it to a photomultiplier. The performance of the detector was evaluated by monitoring the native fluorescence of the amino acid tryptophan and the proteins α-chymotrypsinogen A, carbonic anhydrase II, lysozyme and trypsinogen upon excitation at 280 nm. The test compounds were analysed using background electrolytes (BGEs) of sodium phosphate at pH 3.0 and 11.3. The results were compared to experiments of CE with UV absorbance detection. For tryptophan, a linear fluorescence response was obtained with a dynamic range of over 4 orders of magnitude, and a limit of detection (LOD) of 6.7 nM. This LOD was a factor of 200 more favourable than UV detection at 280 nm, and a factor of 20 better than detection at low-UV wavelengths. All tested proteins showed linear fluorescence responses up to 250 μg/mL. LODs were typically in the 10–20 nM range. These LODs were a factor of 25 lower than for UV detection at 280 nm, and comparable to UV detection at low-UV wavelengths. Overall, Flu yields much more stable baselines, especially with a BGE of high pH. The applicability of CE–Flu is demonstrated by the analysis of a degraded protein mixture, and of an expired formulation of the protein drug human growth hormone, indicating that protein degradation products can be selectively detected.