Thermal- and photo-induced transformations of luminescence centers in αd-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> anion-defective crystals

The thermal- and photo-induced transformations of luminescence centers in anion-defective crystals of α-Al₂O₃ have been investigated. It has been found that the exposure of crystals to ultraviolet light at temperatures in the range 50–900°C leads to substantial changes in their thermoluminescence and radioluminescence spectra. According to the optical absorption and photoluminescence data, the detected F-type centers have been identified and the temperature ranges of the F → F ⁺ → F ₂ transformations and their possible mechanisms have been determined. The special attention has been drawn to the detailed similarity in the formation of complex F ₂-type centers in the initially perfect α-Al₂O₃ crystals irradiated with fast neutrons and in the studied anion-defective crystals.     

Unprecedented ultrahigh photocatalytic activity of δ-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> for cylindrospermopsin decomposition

The delta phase of bismuth oxide (δ-Bi₂O₃) is an important metal oxide due to its highest conductivity of any oxide material. However, it is only stable over a narrow high temperature range, and thus, incorporation of small, high-valence cation is a prerequisite for stabilizing its cubic structure to room temperature. The δ-Bi₂O₃ is also known to have low photocatalytic activity because of its low conduction band edge. As a consequence, the conduction band electrons cannot be consumed by the dissolved oxygen to produce superoxide radicals. Herein, for the first time, the δ-Bi₂O₃ has been successfully synthesized through a facile hydrothermal route without addition of any dopant. The as-synthesized δ-Bi₂O₃ shows ultrahigh photocatalytic activity for cylindrospermopsin decomposition. Within only 20 min of UV irradiation, the degradation efficiency for cylindrospermopsin by 0.5 g/L of the δ-Bi₂O₃ with a cylindrospermopsin concentration of 5 mg/L reaches 98%. Restricted charge carrier recombination and effective consumption of the conduction band electrons are behind such an unprecedented high photocatalytic activity of the δ-Bi₂O₃.

Open image in new window

Graphical abstract ?

     

Effect of ionic polarizability on oxygen diffusion in δ-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> from atomistic simulation

The effect of polarizability of cation dopants on oxygen diffusion in δ-Bi₂O₃ is determined using molecular-dynamics simulation in which the polarizability of the ions is treated within the shell model. It is found that the magnitude of the oxygen polarizability has no affect on diffusion. However, the high cation polarizability, associated with the lone pair of electrons in Bi, is found to be the key to achieving sustained oxygen diffusion. Consistent with earlier experimental results, the oxygen diffusion path is found to be between oxygen equilibrium sites, which are displaced from the 8c oxygen sites of the fluorite lattice.     

Luminescence properties of Nd<Superscript>3+</Superscript>-doped Y<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles in organic media

Nd³⁺-doped yttrium oxide nanoparticles (Y₂O₃:Nd) with cubic phase were obtained successfully by a glycine-nitrate solution combustion method. The results of Fourier transform infrared spectra (FTIR) showed that the –OH groups residing on the nanoparticles surfaces were reduced effectively by modifying with capping agent. The modified Y₂O₃:Nd nanoparticles displayed good monodispersity and excellent luminescence in N,N-dimethylformamide (DMF) solvent. Some optical parameters were calculated by Judd–Ofelt analysis based on absorption and fluorescence spectra. A relative large stimulated emission cross section, 1.7×10⁻²⁰ cm², of the ⁴F_3/2→⁴I_11/2 transition was calculated. Theses results show that the modified Y₂O₃:Nd nanoparticles display good luminescence behavior in organic media.     

Magnetic and magnetoresistive properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sr<Subscript>2</Subscript>FeMoO<Subscript>6–δ</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoheterostructures

A method has been developed for fabricating nanoporous matrices based on anodic aluminum oxide for the deposition of ferromagnetic nanoparticles in them. The modes of deposition of strontium ferromolybdate thin films prepared by the ion-plasma method have been worked out, and the magnetic and magnetoresistive properties, structure, and composition of the films have been investigated. It has been revealed that the microstructure and properties of the strontium ferromolybdate films deposited by ionplasma sputtering depend on the deposition rate and the temperature of the substrate. Based on the measurement of the electrical resistivity of nanoheterostructures in a magnetic field, it has been found that the magnetoresistance reaches 14% at T = 15 K and B = 8 T, which is due to the manifestation of tunneling magnetoresistance.     

Phase formation in the BaCO<Subscript>3</Subscript>–PbO–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> system

Features of the formation of lead-ferroniobate compounds in the xBaCO₃–(1 – x)PbO–Fe₂O₃–Nb₂O₅ system by solid-phase synthesis are investigated. For perovskite-type lead-ferroniobate solid solution, a single-phase concentration region is revealed at 1233 K. The crystalline structures of the synthesized compounds are refined using Rietveld analysis and the Pm3?m and R3m space groups. Ceramic samples of lead ferroniobate are studied by scanning electron microscopy.     

Electrical switching in the MoO<Subscript>3</Subscript>–WO<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> and MoO<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

High field electrical switching on blown films of MoO₃(60%)–P₂O₅(40%), MoO₃(50%)–WO₃(10%)–P₂O₅(40%), and MoO₃(45%)–WO₃(15%)–P₂O₅(40%) having different thicknesses was studied and compared. Switching was observed using two terminal samples. S-type current–voltage characteristic (current-controlled negative resistance—CCNR) with memory was observed in molybdenum–phosphate glasses, but N-type characteristic (voltage-controlled negative resistance—VCNR) with threshold in tungsten–molybdenum–phosphate glasses was observed. The important observation was that with the addition of WO₃ to binary MoO₃–P₂O5 led to a change of I–V characteristic from CCNR with memory to VCNR with threshold. The measurements of density and molar volume showed linear relation between MoO₃ content and density which decreased with the increase of MoO₃ content. The samples’ thickness had no significant effect on threshold voltage. The attained results also indicated that the electrode material had no effect on switching property of devices. The switching behavior of the devices did not show any dependence on the polarity of the applied voltage. In terms of the effect of heat on the switching behavior of molybdenum–phosphate glasses, it was found that threshold voltage decreases with increasing of temperature. Finally, the switching phenomenon was explained by thermal (formation of crystalline filaments) and electronic models.     

Spectroscopic characteristics of anionic centers in α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> crystals bombarded by Cu<Superscript>+</Superscript> and Ti<Superscript>+</Superscript> ions

We have studied the effect of bombardment by Cu⁺ and Ti⁺ ions with energy 30 keV on the optical absorption and luminescence of F centers in oxygen-deficient aluminum oxide. We have shown that in the induced optical absorption spectra there are six components of gaussian shape, which can be assigned to absorption bands of F⁺, F², and F₂⁺ centers. We have established that bombardment of the samples by ion beams has a weak effect on the thermoluminescence parameters in the 3.0 eV and 2.4 eV bands, while in the 3.8 eV luminescence band for F⁺ centers, the thermoluminescent response increases considerably. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 75, No. 3, pp. 422–424, May–June, 2008.     

Electron paramagnetic resonance of Er<Superscript>3+</Superscript> ions in a polycrystalline α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

The EPR spectra of rare-earth Er³⁺ ions in a polycrystalline corundum α-Al₂O₃ synthesized by the sol-gel technology were revealed. It is shown that the EPR spectra belong to the Er³⁺ ions in the ground state corresponding to the lower Stark sublevel of the ⁴ I _15/2 term and can be described by the spin Hamiltonian of axial symmetry with an effective spin S = 1/2 and the g tensor with components g _‖ = 12.176 and g _⊥ = 4.14. The average value of the g tensor (〈g〉 = 6.82) corresponds to the Γ₇ state in a cubic field. Erbium is assumed to substitute for aluminum in the Al₂O₃ corundum crystal. The local symmetry C ₃ of the Al³⁺ ion remains despite the pronounced expansion of the lattice around the Er³⁺ ion.     

KF-doped BaTi<Subscript>2</Subscript>O<Subscript>5</Subscript> ferroelectric ceramics by solid-state reaction of KF and sol–gel-derived BaTi<Subscript>2</Subscript>O<Subscript>5</Subscript> powders

We report KF-doping work on the recently found ferroelectric material BaTi₂O₅. The ceramic samples, Ba_1-xK_xTi₂O_5-xF_x, were synthesized by solid-state reaction of mixed KF and sol–gel-derived BaTi₂O₅ powders at 1150 °C. An almost pure phase was obtained for nominal composition x≤0.097, while electron probe microanalysis indicated that the real incorporated K and F contents were less than half of the nominal values. It was observed that KF-doping is beneficial in enhancing the ceramic density to some extent, which is a key issue in sol–gel-derived BaTi₂O₅ ceramics, due to a possible liquid-phase sintering mechanism through the presence of melted KF at the sintering temperature. Scanning electron microscopy images showed that these porous ceramic samples are composed of sub-micron-sized powder aggregates which, with increasing KF-doping, undergo further agglomeration. Dielectric measurement from room temperature to ∼ 560 °C showed a broad ferroelectric phase transition, with T_C ∼ 430 °C for the undoped sample. As KF-doping increases, T_C decreases, and the magnitude of the dielectric constant maximum also displays a decreasing trend. The strongly reduced dielectric response can be partly understood by regarding the porous ceramic sample as a composite material composed of bulk BaTi₂O₅ and air, where the porosity has a significant influence on the effective dielectric constant. PACS 77.84.-s; 77.84.Dy; 81.20.Fw     

Adhesion at the interfaces between BCC metals and α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

Ab initio calculations of the atomic and electronic structures of Me(111)/α-Al₂O₃(0001) interfaces (Me = V, Cr, Nb, Mo, Ta, W) in the framework of density functional theory are reported. The energies of separation of metal films from oxide surfaces have been calculated. The structural and electronic factors responsible for the strong adhesion of bcc metal films on the oxygen termination of the surface of aluminum oxide have been analyzed.     

Fabrication of α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> bi-functional composites with hierarchical and hollow structures and their application in water treatment

The α-Fe₂O₃/TiO₂ bi-functional composites with hierarchical and hollow structures are fabricated through a hydrothermal route. The adsorption performance and photocatalytic activity of the composites towards Pb²⁺ are investigated in this work. Different adsorption kinetics models and equilibrium models are used to explore the adsorption behavior of hierarchical α-Fe₂O₃/TiO₂ hollow spheres. Experimental data show that adsorption kinetics of the hierarchical α-Fe₂O₃/TiO₂ hollow spheres can be fitted well by the pseudo-second-order model, while the isothermal data can be perfectly described by the Langmuir adsorption model. The maximum adsorption capacity of the hierarchical α-Fe₂O₃/TiO₂ hollow spheres is 32.36 mg g^?1. Moreover, the hierarchical α-Fe₂O₃/TiO₂ hollow spheres possess photocatalytic oxidation character under simulated solar light irradiation. The results demonstrate that the hierarchical α-Fe₂O₃/TiO₂ hollow spheres, as effective and cheap materials, can be applied to the removal of heavy metal ions from wastewater.     

Facile fabrication of α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Ag<Subscript>2</Subscript>S heterojunction with enhanced photoelectrochemical water splitting property

The α-Fe₂O₃/Ag₂S p-n heterojunction has been prepared via a facile room temperature successive ionic layer adsorption and reaction (SILAR) method. The heterojunction exhibits higher photoelectrochemical property compared to bare α-Fe₂O₃. The amount of Ag₂S has a significant effect on the PEC performance, which could be controlled by varying the number of SILAR cycles. The α-Fe₂O₃/Ag₂S p-n heterojunction prepared via 6 cycles of SILAR processes displays the best photoelectrochemical performance, which exhibits 1.8 times enhancement of photocurrent density and 70 mV cathodic shift of onset potential compared to bare α-Fe₂O₃. The improved PEC performance could be attributed to the formation of p-n junction between Ag₂S and α-Fe₂O₃, which not only enhanced the optical absorption ability, but also facilitated the separation efficiency of photogenerated charge carriers and passivized the surface state.     

Adhesion of niobium films to differently oriented α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> surfaces

The atomic and electronic structures of the Nb/α-Al₂O₃ interface are studied by the electron density functional method. The structural and electronic properties of three corundum surfaces, as well as chemical bonds produced by metallic niobium films at variously oriented interfaces, are discussed. Relations between the electronic structure, geometry, and mechanical properties of the interfaces are analyzed. It is shown that the adhesion of niobium films to a great extent depends on the type of oxide surface.     

O<Subscript>2</Subscript> photodesorption from AuO<Stack><Subscript>2</Subscript><Superscript>−</Superscript></Stack> and Au<Subscript>2</Subscript>O<Stack><Subscript>2</Subscript><Superscript>−</Superscript></Stack>

Using time-resolved photoelectron spectroscopy, the decay channels of AuO₂⁻ and Au₂O₂⁻ following photoexcitation with 3.1-eV photons have been studied. For AuO₂⁻, a state with a rather long lifetime of 30 ps has been identified. Its decay path could not be determined but photodesorption can be excluded. For Au₂O₂⁻, the spectra indicate O₂ desorption after 3.1-eV photoexcitation on a time scale of 1 ps. While comparing these results on Au _n O₂⁻ with analogous data on Ag _n O₂⁻ clusters, a discernible pattern emerges: for dissociatively bound O₂(AuO₂⁻, Ag₃O₂⁻), there are long-living excited states which do not decay by oxygen desorption, while for molecular chemisorption (Au₂O₂⁻, Ag₂O₂⁻, Ag₄O₂⁻, Ag₈O₂⁻), the 3.1-eV photoexcitation triggers fast O₂ desorption with a high quantum yield.     

Microwave dielectric properties of the 5.5Li<Subscript>2</Subscript>O–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>–7TiO<Subscript>2</Subscript> ceramics

A new Li₂O–Nb₂O₅–TiO₂ (LNT) ceramic with the Li₂O:Nb₂O₅:TiO₂ mole ratio of 5.5:1:7 was prepared by solid state reaction route. The phase and structure of the ceramic were characterized by X-ray diffraction and scanning electron microscopy (SEM). The microwave dielectric properties of the ceramics were studied using a network analyzer. The microwave dielectric ceramic has low sintering temperature (∼1075°C) and good microwave dielectric properties of ε _r=42, Q×f=16900 GHz (5.75 GHz), and τ _f =63.7 ppm/°C. The addition of B₂O₃ can effectively lower the sintering temperature from 1075 to 875°C and does not induce degradation of the microwave dielectric properties. Obviously, the LNT ceramics can be applied to microwave low temperature-cofired ceramics (LTCC) devices.     

Specific features of the magneto-optical properties of α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> in the IR region

The spectra of reflection and magnetoreflection of light from the crystalline insulator α-Al₂O₃ in the IR spectral region (λ = 2.5–25 μm) are investigated. Some features in the magnetoreflection spectra in the wavelength range corresponding to the excitation of optical phonon modes in α-Al₂O₃ are found. A significant increase in magnetoreflection is observed near these wavelengths. The amplitude and shape of the magnetore-flection spectra for the p and s polarizations of probe light are determined. It is shown that the optical and magneto-optical properties of α-Al₂O₃ in the IR region can be described on the basis of the theory of polaron excitation. A satisfactory correlation between the theoretical and experimental spectra is obtained, which indicates that polarons play an important role in determining the optical characteristics of nonmagnetic insulators and make the dominant contribution to the magnetoreflection spectra.     

Facile fabrication and optical property of β-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> with novel porous nanoring and nanoplate superstructures

Novel β-Bi₂O₃ crystals with nanoring and nanoplate surperstructures, which are composed of porous nanoparticles with mean pore diameter of 8 nm, were produced via a facile soft chemistry route of solvent refluxing technique. Most of the rings have the average inner diameter of 200 nm and the mean rim thickness of 20 nm. Photoluminescence spectra of the nanorings at room temperature were investigated, which demonstrated that the rings presented excellent optical properties. The influence of aging time on the morphology and structure of β-Bi₂O₃ superstructures was also studied, indicating that the nanoring superstructures transformed into nanoplates after a long aging time. The formation mechanism of the β-Bi₂O₃ superstructures was also explored. This approach will be further extended to solvent-controlled fabrication of related oxides with novel complex superstructures.     

High-Temperature Heat Capacity of Zn<Subscript>2</Subscript>V<Subscript>2</Subscript>O<Subscript>7</Subscript>–Cu<Subscript>2</Subscript>V<Subscript>2</Subscript>O<Subscript>7</Subscript> Solid Solutions

Differential scanning calorimetry has been used to study the influence of temperature on the heat capacity of synthesized vanadates Zn₂V₂O₇, (Cu_0.56Zn_1.44)V₂O₇, and (Cu_1.0Zn_1.0)V₂O₇. It is found that dependences C_p = f(T) have extremes. The thermodynamic properties of Zn₂V₂O₇ have been determined.